Search Documents

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By J. D. Vincent

The Henderson mine site is located at Red Mountain on the eastern slope of the Rocky Mountains, approximately 50 miles west of Denver, Colorado. The mill site is on the west slope of the Rockies and mine and mill will be connected by an underground railroad. All designs were for a 30,000 ton per day molybdenite processing plant with provisions for future expansion up to 50,000 ton per day if required. This plan did not just happen, but slowly evolved over the course of about three and one-half years. Many plants cannot afford such a delay, but the Henderson project will take about 10 years from the time it was first discovered until production starts, and these 3 !1 years were well spent in determining the best possible plant site and flowsheet. This paper describes some of the problems and the decisions made in arriving at the final location and flowsheet. The paper does not go into the specific details of how protection of the environment went hand-in-hand with all other project considerations. This particular aspect of the planning has been well-reported on other occasions and considerable information on it is readily available.

Jan 1, 1972

By Nikhil Dhawan, Shrey Agrawal

Feldspar, a low-alumina, and abundantly available aluminosilicate source, is explored in this study to extract aluminum and potassium values. The sample comprises lamellar layers of microcline and albite with quartz containing 17.4% Al2O3, 9.67% K2O, and 66.3% SiO2. Mechanical (milling) and thermal (alkali and acid baking) activation are investigated, followed by HCl leaching. The milling treatment up to 6 h is inefficient in phase dissociation and results in ~ 40% Al and K dissolution. The alkali thermal treatment yielded 80% Al and 71% K extraction. Direct precipitation of the dissolved Al and Si values yielded alumina purity of ~ 29%, and silica gelation separated SiO2 and improved alumina product (94% purity, 71% recovery). Acid baking yielded 98% pure alumina precipitate; however, Al and K extraction were limited to ~ 45% and 65%, respectively. The microwave-assisted alkali treatment was optimal with 800 W and 10 min processing conditions yielding 80% Al and 71% K recovery with 2.26 kWh/kg alumina of thermal energy consumption. The final product contains γ-alumina with a specific surface area of 87 m2/ g. Keywords Feldspar · Alumina · Potassium ·

May 18, 2022

By E. Tondu

Separation Technologies Inc.’s (STI) electrostatic separation technology is a dry, continuous process for the separation of discrete particles. This high-volume process does not require any additives nor is any additional waste produced. In December 1993, STI, in cooperation with New England Power(NEP), installed an 18-t/h (20-stph) prototype electrostatic separator at NEP’s Salem Harbor plant. The plan was to convert waste streams of type F fly ash into commercially valuable products. In July 1995, a second separator was installed at NEP’s Brayton Pointplant. Fly ash feed, ranging from 6% to 25% carbon (loss-of-ignition fly ash or LOI), is separated into <3% LOI “clean” ash and sold as a portland cement substitute in the New England concrete markets.

Jan 1, 1996

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center&apos;s 900-lb/hr pilot plant, approximately 85 percent of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to <1,000 ppm equivalent Si02, while maintaining a Ca(II) content of 516 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water.

Jan 1, 1970

By S. W. Nicholson, L. G. Woodruff, K. J. Schulz, W. E. Cannon

The 1.1 Ga Midcontinent rift of North America has many similarities to the geology of the Voisey&apos;s Bay region in Labrador and the geology of the Noril&apos;sk region in Siberia. These similarities include the hosting of large volumes of sulfur- undersaturated and trace-element-enriched basalt, having igneous centers characterized by crustal contamination, being characterized by metal depletions in some mafic units (an indication of prior sulfide segregation) and having known occurrences of Ni-Cu sulfide mineralization. These similarities along with new geophysical data and refined models for Ni-Cu sulfide deposits suggest that the Midcontinent rift probably contains undiscovered Cu-Ni [±] PGE sulfide deposits, some of which could be the size and grade of a Voisey&apos;s Bay or Noril&apos;sk deposit. In particular, intrusions and related feeder systems that occur in northern Michigan and Wisconsin, as well as to the southwest along the rift margin, deserve serious examination.

Jan 1, 1999

By Gene E. McClelland, Dirk J. A. van Zyl

5.1 INTRODUCTION Heap leach cyanidation techniques possess considerable potential for exploitation of low-grade ores, small ore bodies, mine strip waste and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successfu1, ore must exhibit certain characteristics, as previously discussed in Chapter 1. Primary among the necessary ore characteristics is that the ore must have good permeability after being crushed or treated and stacked into heaps if uniform distribution of the cyanide leach solution is to be achieved. Gold and silver ores containing excessive amounts of clays or fines generated by crushing are some of the most difficult to treat successfully by heap leaching. The presence of excessive amounts of slimes (generally classified as minus 50-micron or 270 Tyler mesh sieve size particles) in the heap leach feed will slow the percolation flow of the leach solution, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap, causing the leach solution to run off the sides of the heap rather than to penetrate the ore heap. The problem of heap leaching ores containing fines can be aggravated during stacking and preparation of the ore heaps, because natural sorting of coarse and fine material occurs during these steps (Johanson, 1978). This phenomenon results in a concentration of ore fines at the center of individual ore piles and a concomitant concentration of larger rock fragments on the lower slopes and base of the piles. When the individual piles within the heap are leveled off prior to installation of the sprinkling system which delivers the leach solution, additional segregation occurs as the fines sift through the coarser ore particles. The segregation results in localized areas or zones with marked differences in permeability. As a consequence, the leach solutions follow the path of least resistance, percolating downward through the coarse ore regions and bypassing or barely wetting areas that contain large amounts of fines or slimes. Effective utilization of marginal gold and silver resources through heap leach processing requires the development of new methods in order to achieve more uniform size distribution during ore heap preparation and better slime control during leaching.

Jan 1, 1988

By Douglas B. Silver

The key to unlocking value is to find opportunity where others have missed it. How does a company find value in a thoroughly explored asset? This article explores the approach taken by one company and the results it achieved from working this problem. The town of Shafter is located on a small bend in the road in west Texas&apos; Big Bend Country. Its past emulates the glory days of so many other mining camps. A discovery was made, fortunes were built and World War II shut down the operation. The Shafter deposit continues to be one of the larg¬est undeveloped primary silver deposits in North America. Gold Fields Mining Co. recognized the area&apos;s potential in 1977 and embarked on studies to reopen and develop the district. Gold Fields spent $16 million on the Shafter project. It drilled more than 86,240 m (282,940 ft) in 475 holes, sunk two shafts and developed 1,550 m (5,100 ft) of underground workings. Today, the mothballed 447-kW (600-hp), single-drum Nordberg hoist and permanent production-type, single-compartment headframe continue to crown the shaft. Other buildings onsite house compressors, mine pumps, spare parts, drill core and other supplies. All these items look as though they arrived yesterday. By 1982, Gold Fields had completed an extensive feasibility study with ambitions to. construct a 1.36-kt/d (1,500-stpd) agitated cyanidation mill and base metal gravity circuit. Reserves at Shafter stand at 4.23 Mt (4.67 million st) grading 193.5 g/t (5.65 oz/st) silver. Gold Fields planned to produce 71.5 t/a (2.3 million oz/year) of silver at a head grade of 196.2 g/t (5.73 oz/st) silver with a 77% recovery rate. Cash costs were projected to be $5.54/oz with an anticipated initial and total capital cost of $46.2 million and $51.3 million (1984 dollars), respectively. The study assumed a silver price of $8.60/oz that has not been seen since the Hunt brothers quit buying silver. When silver prices declined, Gold Fields put the property up for sale.

Jan 1, 1999

By John Litz

The term "refractory gold ores" refers to a wide number of ore types which are not readily amenable to direct cyanidation. A number of processes have been used commercially, and a number of others have been proposed and in many cases pilot tested. The selection of the appropriate process for an ore should not be arbitrary. Ore grade may preclude some processes, but a good understanding of the ore mineralogy can guide the selection. Many present gold operations and many potential gold operations have faced or are facing problems with refractory gold mineralization. We at Hazen Research have had the opportunity to perform bench testwork and in some cases, pilot plant testing on a number of refractory ores. The data included in this paper are excerpted from the testing of fifteen ores which cover a wide range of mineralogical compositions. This paper is not intended to be a treatise on the processing of refractory gold ores. In many of these gold projects, not all of the standard process alternatives were evaluated, nor was adequate mineralogical work performed. Such is the dilemma of contract research. "If I believe that I don't need it, why should I pay to have it done." The intent of this presentation, therefore, is to show how different ores respond to the various processes, and to demonstrate that one must have an open mind when developing a process for a specific refractory gold ore.

Jan 1, 1998

By George L. Wilhelm

Many factors, some of which are not easily defined or described, must be considered in the design of a hydraulic backfill system. After participating in the design of several plants, I have a conviction that future refinements in sandfill systems must come in large part, from the merging of good design ideas and information from existing operating plants. It is important then, that we document and publish information on existing plant designs and their operating characteristics. This information will then be available for use by our successors and later innovators in hydraulic fill placement. The Mayflower hydraulic sandfill system is similar to other plants. The intent of this paper is to describe only this system&apos;s unique design and operating characteristics. I will not describe in any detail, the familiar elements of the system. I will document some of the observed hydraulic characteristics of the system, elaborate on some of the design situations that had to be solved, and will discuss operating factors that are not generally described in our technical literature.

Jan 1, 1968

By Yuting Xue, Lihong Zhou, DAVOOD BAHRAMI

The paper discusses the use of machine learning (ML) to develop a predictive model for determining the location and size of underground mine fires using simulated ventilation data. The study highlights the importance of prompt fire location determination for effective firefighting strategies and reducing injury risks. The ML model was trained with simulated data and achieved an accuracy score of 0.920, which improved to 0.962 by grouping closely connected airways.

Sep 1, 2023

By Richard Klimpel

The laboratory ball mill grinding of coal/water slurries is described for three coals. Emphasis is placed on the measurement of specific rates of breakage for various operating conditions. Corresponding rheological information is also presented based on data collected using a rotational viscometer. A rheological explanation of the influence of various slurry fluidity conditions on the specific rates of breakage is presented. This rheological approach has proved useful In both the identification of suitable chemicals for increasing breakage rates in coal/mineral slurry grinding and in the plant scale implementation of dense slurry grinding systems.

Jan 1, 1982

By Richard Switalski, Thomas Scotese, James Morrison, Randall Essex

OVERVIEW Like many older metropolitan areas across the U.S., the Greater Cleveland area is served by a combination of separate sanitary sewers and combined sanitary-stormwater sewers. In 1966, a Master Plan was implemented by the Northeast Ohio Regional Sewer District (District) to minimize pollutant overflows into adjoining Lake Erie and its tributary rivers and streams, that would occur during wet weather events. One component of the Master Plan was to reduce the load on combined sewers by constructing new conveyances to intercept separate sanitary flows and convey them to upgraded regional waste water treatment plants for priority treatment. As part of a 15-year program to construct 74 km (46 miles) of new interceptors, the West Leg Interceptor (WLI) Project intercepts flows from four decommissioned waste water treatment plants (WWTPs), and conveys those flows to the new Southwest Interceptor (SWI), which conveys the flows to the Southerly Treatment Plant, a tertiary level treatment facility. The WLI Project was built in sections to permit decommissioning of the WWTPs as each segment of the interceptor system was completed and put into service. Flows from the first of the four WWTPs was converted to the WLI in November, 1992; the final connection was achieved in July 1994. The WLI comprises 9.1 km (5.7 miles) of 21 to 29 m (70 to 95 ft) deep mainline interceptor tunnel, four vortex drop structures, approximately 2 km (1.3 miles) of shallow tunneled connector sewer to the mainline, approximately 2.9 km (1.8 miles) of open cut connector sewers, five construction work shafts (not including one work shaft constructed under SWI Contract 6 at the north end of the WLI), and 15 access shafts.

Jan 1, 1995

By Kenneth Ronald Miller

Thunder Basin Coal Company&apos;s Black Thunder Mine is located 80 km (50 miles) southeast of Gillette, Wyoming in the Powder River Basin. Surface coal mining operations began in 1977. The Black Thunder Mine has been North America&apos;s largest producing coal mine for over 5 years. Production in 1988 totaled 22.6 million mt (24.9 million st) of sub-bituminous coal. Thunder Basin Coal Company is a subsidiary of Atlantic Richfield Company. The mine began as a truck-shovel stripping and mining operation. Haul trucks of 154 mt (170 st) capacity were part of the original fleet. In 1985, 218 mt (240 st) capacity trucks were introduced to the fleet. In 1988 a dragline was added for stripping. A single, primary/ secondary crushing stream feeds either a slot storage facility or dual silos. Three loading points are situated over two rail loops serviced by the Burlington Northern and Chicago North-western Railways. A Near Pit Crushing and Conveying system is currently under construction. It is expected to be completed during the fourth quarter of 1989. During the past 10 years, the conceptual crushing/conveying design has changed several times as technology and commodity markets have changed. The system under construction will have a capacity of 4700 mtph (5200 stph). The overland belt will be 3570 m (11,700 ft) long and 1800 mm (72 in.) wide. The belt speed will be 300 meters per minute (1000 fpm). Two separate crushing streams will feed the overland belt. Each stream will be comprised of a dump hopper at reclaim surface elevation, a drag feeder, a two-stage triple-roll crusher, and an incline conveyor of 2700 mtph (3000 stph) capacity. This article will describe the different concepts and factors that have resulted in the system design now under construction.

Jan 1, 1989

By Musa D. Manzi, Raymond J. Durrheim, Richard T. Masethe

An investigation into the source mechanism of mining-induced seismic activity plays a vital role in understanding the various modes of failure observed in the underground deep-level South African mining environment. The seismic events data for this study was captured by the mine-wide seismic system operating at Kloof Gold Mine. This system comprises 40 4.5 Hz tri-axial geophones sampling at 6 kHz installed at locations that surround the stopes mining the Ventersdorp Contact Reef (VCR), Main Reef (MR) and Kloof Reef (KR). A set of 103,753 mining-related seismic events (-3.0≤ ML ≤2.7) that occurred during 2017 and 2018 was selected for this study. The mining depth of these seismic events ranges from 1600 – 4200 m; most located close to stopes mining the VCR ore body. The main criteria used to select a subset of events for detailed analysis were the number of stations that recorded the seismic event and the azimuthal distribution of the sensors.

Apr 26, 2022

By Arthur S. Radtke

The structural setting of disseminated-replacement gold deposits of the Carlin-type and other aspects of their genesis are closely related to events which took place during the evolution of the Basin and Range province. The deposits formed as a result. of chemical and physical processes which took place at shallow depths in the roots of hot spring systems at moderate temperatures (about 200°C) and low pressures (about 25 bars) (Radtke and Dickson, 1974). Locations of Carlin-type gold deposits in the Basin and Range province are shown in Figure 1. Most of the block-faulted mountain ranges in the Great Basin formed by tectonic activity that happened since Miocene time, although faulting in some places probably began in Eocene to Oligocene time (Hamilton and Myers, 1966). The Carlin-type deposits are spatially related to Basin and Range-type faults: Many deposits, such as Getchell, Pinson, Preble, and Cortez, occur along the flanks of ranges, while other deposits, including Carlin (Radtke, 1974) occur within the ranges in areas characterized by crosscutting and intersecting high-angle or Basin and Range-type faults. The association of the ore deposits with Basin and Range-type faults is evidence that ore deposition is young, Miocene or later. The steep, high-angle faults played three roles: first, they provided deep channels for upward-flowing solutions; second, in preparing the rocks for fluid penetration by brecciation and general rock dislocation; and third, they moved sedimentary carbonate rocks, favorable for ore deposition, from deep levels to near-surface positions where the physico-chemical conditions were more suitable for the deposition of ore.

Jan 1, 1976

By T. L. Carstensen

The Miami In-situ mine of BHP Copper is located in Globe-Miami, Arizona. The mine leaches mineralized leach capping over a supergene enriched sulfide deposit, and has produced over 500 million lbs of copper during the last 50 years. The Miami unit has identified several opportunities to enhance and expand in-situ production. A computer block model consisting of strict geologic controls, mineralogy, and metallurgical data was developed to assist in the determination of the leachable copper resource. An understanding of the accessibility and solubility of the resource to leaching solutions and the integration of hydrogeologic and hydrometallurgical information was necessary for completion of this project.

Jan 1, 1997

By G. L. Mowrey

In addition to developing various types of coal interface detection systems, the U.S. Bureau of Mines is actively involved in developing a coal rib thickness monitoring system for high wall mining applications. One particular system that appears to show promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1995

By M. Tapper

If one considers that prehistoric man&apos;s first house may have been a limestone cave, calcium carbonate may be the most timeless of all building materials. Fanciful history aside, CaCO3 has been used for countless applications in human habitats. After all, tine marble block and tiles have always been the hallmark of eloquents and style. Mortars and cements derived from limestone have held together the very blocks of our civilization. In modem times, synthetic polymers are blended with ground limestone to produce everything from pipe, floor tile, cultured marble and house siding. All of these miracles of our technology contain CacO3 of various sizes and in varying amounts. This paper will discuss some of the critical attributes of CaCO3 which make it suitable for the new building products that have helped increase our standard of living. The vehicle of discussion will be a residential, single family house.

Jan 1, 1993

The exploitation of mineral deposits for economical recovery of the contained minerals has many aspects differing from other industrial or manufacturing operations. However, generally accepted principles of good organization and management applicable to industrial plants are similarly effective for mineral processing plants. A more detailed coverage of organizational structures and management techniques than is possible in this section can be obtained from many good books devoted wholly to these subjects. A few of the more readily available examples are included in the general references at the beginning of this section. The field of mineral processing encompass a wide variety of minerals, processes, flowsheets, equipment, and end products. Mineral deposits, mines, and related beneficiation plants are found in all parts of the globe, often in remote locations with no nearby support for supplies and maintenance. Available labor is frequently unskilled, sometimes primitive, and often untrained without machine and hand tools or heavy equipment experience. Such situations call for well- planned and conducted training programs covering the full range of mining-type job skills. Climates can range from arctic to tropical and from arid to extremes of rain or snow, and the mine and plant sites can be almost anywhere. However, it is often possible and sometimes necessary for

Jan 1, 1985