Search Documents

By J. C. Irvine

A recent development in underground drilling has been the introduction of the down-the-hole drill, an old and very familiar tool to the surface operator. The idea of moving such a rig underground is not new. Tests were conducted at INCO in Canada and Mt. Isa, Australia in the early 1960's, and St. Joe used one for underground exploration in their Missouri lead mines in the mid-1960's. However, the trend to full scale production programs did not start until the mid-1970's. The first successful North American test was at INGO in early 1973. This led to a large-scale pillar recovery and open stoping program which en¬compassed 25 drilling units by mid-1976. Meramec Mining Company tested a unit using air boosted up to 200 psi (140, 000 kg(m2) in the summer of 1973 which by 1976 led to an open stope and pillar drilling program using 12 units. By mid-1976, production units using boosted air were also in use at Pilot Knob in Missouri and at St. Joe in Balmat, New York. Experimental and utility units were in use in several other mines and down-the-hole drills were being seriously considered for at least one major new underground mine.

Jan 1, 1976

By Z. Hyder, A. Urquidez

"INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is located approximately 26 miles southeast of Carlsbad, New Mexico and is the nation’s first underground geologic repository for transuranic (TRU) and TRU-mixed waste (see Figure 1). The WIPP facility was opened for operation in 1999 when the first TRU waste shipment arrived at the WIPP facility for disposal.WIPP facility does not employ typical production aspects of a conventional mine. Instead, the mining focus is on the quality of the excavation to ensure safe disposal of TRU and TRU-mixed waste (Walls, 1991). GEOLOGY WIPP underground repository is mined within a 2,000 feet-thick bedded-halite formation (Salado Formation) (see Figure 2). The WIPP underground repository is located approximately 2,150 feet beneath the surface near the center of the Salado Formation. Geologic criterion and site-selection factors evaluated for the selection of the repository included topography, depth, thickness, lateral extent, lithology, stratigraphy, structure, erosion, dissolution, subsidence, surface water, aquifers, hydrologic transport, climatic fluctuations, manmade penetrations (U.S. Department of Energy, 1980).FACILITY DESIGN Profit did not play a major role in the WIPP’s conception like in a conventional mine. This was due to the extensive amount of additional regulations and safety controls that had to be built into the WIPP facility. Since it is nuclear and hazardous waste disposal facility, it must meet certain federal and state requirements for TRU-mixed waste. One of the major regulatory drivers for the WIPP facility is defined in the WIPP Land Withdrawal Act (LWA). One of the requirements in the WIPP LWA requires the DOE to submit documentation of continued compliance with Title 40 CFR Part 191, Subparts B, and C. These standards are regulated by the Environmental Protection Agency (EPA). The DOE must submit documentation of continued compliance (recertification) with these regulations every five years. In addition to the LWA, the Resource Conservation and Recovery Act (RCRA) is another major regulatory driver for the WIPP facility. Since the WIPP facility is categorized as a “Miscellaneous Unit” under 40 CFR, it must meet extensive environmental performance standards. These standards are defined in the WIPP Hazardous Waste Facility Permit (HWFP). The HWFP defines the terms and conditions that the Secretary of the New Mexico Environment Department has determined necessary to protect human health and the environment (U.S. Department of Energy and Nuclear Waste Partnership LLC, 2015)."

Jan 1, 2017

By B. G. McNish

Neutron Activator Laboratory Analyzer used for Rapid Analysis for Ore Blending, Stripping, and Mine Control BAUXITE is a rock and not a mineral. Since it is a rock, its mineral content varies depending upon the parent material, the topographic location of the deposit and the severity of the weathering and oxidation processes which produced it. At Bauxite, Arkansas the major mineralogical constituent of the bauxite is gibbsite with ~IL- purities of silica, iron oxide, and titania minerals. Minor amounts of other minerals are found. Chemical composition varies from 45% to 60% alumina, 5% to 25% silica, 1% to 15% ferric oxide, and 1% to 3% titania. The Arkansas bauxite region is located entirely within the north- central area of the West Gulf Coastal Plain near the northwestern boundary with the Interior Highlands. The region trends northeast-southwest and is about 42 kilometers long. It is divided into two districts; one in Saline County and the other in Pulaski County. The Saline District is the most important since it has produced most of the bauxite. This district is located at Bauxite, Arkansas and the deposits are found around the flanks of the Saline Dome. It is roughly square-shaped and is about 190 square kilometers in area. The source rock for the deposits is a Late Cretaceous, grey, nepheline syenite.

Jan 1, 1979

By J. S. Wozek

In metallurgical applications, coal fulfills dual roles as a chemical feed stock and as a fuel source. These applications range from cokemaking, ironrnaking (including pulverized coal injection), foundry, basic oxygen furnace / electric arc furnace coal additions, direct ironrnaking, Corex, and the futuristic direct steelmaking. In all steelmaking related processes, chemical reactions are simultaneously temperature and chemical dependent. Therefore, coals used in these processes must consistently comply with specific quality parameters in order to promote efficient operations. This paper limits discussion of Metallurgical Coal Quality to cokemaking and ironmaking applications. Its purpose is to present the customer's perspective on the control of critical coal and coke properties.

Jan 1, 1994

By Michael J. Fiannaca

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Cold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 9 million tons of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 1.0 million tons per year. Careful evaluation of the combined results of successive sampling projects has established the pit plan, mineable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1984

By J. Edberg

"This article details the use of an alternative testing method to the 2004 "Post-Tensioning Institute (PTI) Recommendations for Prestressed Rock and Soil Anchors" manual’s recommendations for temporary and permanent rock anchors for applications in shafts and tunnels. This method was developed and used for the Black River Tunnel (BRT) project in Lorain, OH as a means to reduce testing time of rock bolts during shaft construction while maintaining a similar level of quality control and assurance. The following sections will detail the project background, subsurface characteristics, shaft construction, the 2004 PTI testing method and associated difficulties, the alternative testing method and conclusions reached.Project backgroundThe city of Lorain is located in north central Ohio on the south shore of Lake Erie, approximately 40 km (25 miles) west of Cleveland and 119 km (74 miles) east of Toledo. The city chose to build a large-diameter storage tunnel and pump station to meet its requirements to reduce sanitary sewer overflows to the nearby Black River. NTH Consultants Ltd. (NTH) was retained by the city’s prime consultant, Malcolm Pirnie Inc. (now the water division of Arcadis), to perform a geotechnical investigation, develop design and construction bid documents for the tunnel and shaft liner systems and ultimately provide oversight assistance during the construction phase of the project.The BRT is an approximately 1,700-m (5,560-ft) long, 7-m (23-ft) diameter rock tunnel to be lined with a 5.8-m (19-ft) inside diameter secondary concrete lining (Fig. 1). The tunnel is designed to accept flow at a new drop shaft (Shaft 3) located on the west side of the Black River, across from the city of Lorain Black River waste water treatment plant (BRWWTP). The tunnel will be dewatered at the south end by a large diameter pump station (Shaft 1) located in the existing Lorain Port Authority Public Boat Launch. Flow from the new pump station will be discharged into an existing shallow interceptor sewer and directed back to the BRWWTP."

Jan 1, 2014

By Nick Tessitore, Ryan Marsters, Alex Warren, Dylan Fawaz

The West Gates Deicing Industrial Waste Pond Expansion project at Denver International Airport seeks to expand utilities to accommodate additional terminal gates. The project includes six tunnel crossings beneath taxiways and runways with lengths ranging from 239 to 2,025 linear feet. Excavation methods include shielded tunnel boring machines and steerable auger boring. Designed initial support includes liner plate, steel ribs and lagging, steel casing, and Fiberglass Reinforced Pipe and ranges in size from 24" to 132". This paper will discuss challenges associated with the overall layout and design of the project, including contingencies to protect critical infrastructure. In addition, a construction update is provided.

Jun 23, 2024

By Aarne Visnapuu

Unmodified pneumatic rock drills may have noise levels of 115 to 130 dB at the operator's position. Experimental modifications have been made to a standard drill to suppress the noise from the three main sources: the air exhaust noise, the noise radiated from the drill, and the resonance noise of the steel drill rods. A prototype model developed at the Bureau of Mines, Rolla Metallurgy Research Center, operates at a noise level below 100 dB. A close-fitting case and muffler unit, consisting of a metallic skeleton filled with viscoelastic absorber and having a durable cover, provided both muffling and noise absorption. Damping alloys were used at strategic points in the drill. Drill steel resonance noise was reduced by a constrained-layer treatment on the outside of the drill rod. The singular and combined effects of the treatments are presented in detail.

Jan 1, 1973

By Lloyd E. Haight

After accepting the invitation to make this appearance today, it occurred to me that the subject matter which had been assigned to me, namely, the purpose and role of an advisor, was, contrary to what; some people might think, a controversial subject. In my brief lifetime, I have discovered that the world is full of advisors; that is to say, there are many people who undertake to render advice concerning subject matters upon which they may, or may not be qualified to speak. It shall be my purpose today to set forth what now appears to be the function of the members of the Advisory Council to the U. S. Public Land Law Review Commission; and, in so doing, I hope that I do not offend the Commission or any other-member of the Advisory Council with whom I serve. It has always been my personal conception of the role of an advisor that he should tender advice when it is requested, and then only if he has prepared himself concerning the matter upon which the advice is being given. I am sure it was the Congressional intent at the time the Public Land Law Review Commission was established indeed it was the hope. of Congress--that those of us who were to become members of the Advisory Council were informed upon certain particular subjects and then at the proper time express our opinions upon these subjects-and, by the same token, not attempt to enter opinions upon problems with which we have no experience in theory or in actuality. Some wag once said that if Columbus had had an advisory council, he would still be waiting at the dock in Spain, and there is more truth than fiction in that statement. With this problem in mind, let us examine the purpose of the Advisory Council itself.

Jan 1, 1967

By A. B. Cecala, G. W. Klinowski

Introduction The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour (acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec (50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average millwide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al., 1987). Testing Total mill ventilation systems were evaluated at two processing operations. For both tests, the primary goal was to determine the reduction in respirable dust throughout the structure. Test site No. 1. The first evaluation was performed at a clay-crushing and screening mill in New York. The mill's base dimensions were 39.6 x 9.8 m (130 x 32 ft), giving a volumetric capacity of 4250 m3 (150,000 cu ft). The TMVS was designed to provide 12 m3/sec (25,430 cfm) of ventilation air to the mill, representing about 10 acph. This was accomplished by three 4 m3/sec (8475 cfm) roof-powered exhaustors that were evenly spaced across the roof. Three wall louvers provided inlets for make-up air at the mill's base. Two evaluations were performed at this mill. The first occurred for two days in December when outside air temperatures ranged from -12.2° to 4.4° C (10° to 40° F). Temperatures with the wind chill factor dropped as low as -34° to -40° C (-29 to -40° F) during the early morning. The second evaluation was in April when outside air temperatures ranged between 10° to 26.7° C (50° to 80° F). These two evaluations verified the effectiveness of TMVS in lowering respirable-dust concentrations throughout the mill. Gravimetric-sampler respirable-dust concentrations in December ranged from 0.22 to 2.39 mg/m3 under normal conditions, compared to 0.13 to 1.55 mg/m3 with TMVS. In April, respirable dust concentrations ranged from 0.29 to 4.84 mg/m3 under normal conditions compared to 0.21 to 2.37 mg/m3 with the system on. TMVS also increased visibility throughout the mill building. Dust reductions for gravimetric and RAM-I instruments are listed in Table 1. Each value was determined by comparing the average concentration for the entire day of testing for normal and TMVS values. The mean/standard deviation values for gravimetric and RAM-1 results were 42.5/17.6 and 37.1/16.8, respectively.

Jan 1, 1996

By R. L. Atwood

This paper discusses the metallurgical and Manufacturing input to Merrill-Crowe plants. Topics treated are pregnant solution chemistry, clarification, degassing, zinc addition, product filtration, accounting, and costs.

Jan 1, 1985

By Roberto Pimentel de Souza

CURD started producing pellets in 1969, with one two-million ton straight grate plant. In the beginning of April '73, the second unit came on stream with an additional capacity of 3 million TPY of pellets. In January '77, the third unit started, bringing the annual capacity to 8 million TPY. For the present year 3 more units, 3 million each, are expected to begin production. CVRD's experience is given about the use of different binders and additives. Over the years several kinds of pellets have been produced to satisfy the market requirements. General quality information is given regarding each.

Jan 1, 1978

By Tracy T. Morris

The current state of the mining community has made it imperative for operations to reduce costs and increase productivity in order to remain competitive. This has been done in Colorado with the installation of an Outokumpu flash flotation machine for the production of a gold/silver/lead concentrate.

Jan 1, 1987

By John E. Crawford

A year ago, if I had the pleasure of addressing you, I would have discussed ocean mineral resources from a promotional standpoint. I would have described exciting indications of mammoth tonnages of sea-floor industrial minerals. I would have attempted to fire your imaginations as to the potential of a nation having the technologic know-how to exploit its submerged boundaries. As a first step toward this capability, I would have solicited your support for a Bureau of Mines? program aimed at determining the industrial worth of marine minerals and devising techniques and hard- ware for their recovery. We still need your support, but recently we have ventured out of the realm of planning and into your Government's first program in marine mineral engineering. Today, I wish to describe what we have done within the framework of existing research problems and our possible goals. I will be brief so as to allow ample time for questions, and I can do this with confidence because our program is so new that I need not be chagrined at not having all the answers.

Jan 1, 1965

By James E. Breland

Society's growing concern over the number of deaths and serious injuries occurring in coal mines, coupled with a growing sentiment to develop and promulgate improved mandatory health or safety standards, was no doubt the basis for passage by Congress of the Federal Coal Mine Health and Safety Act of 1969, being Public Law 91-173 approved December 30, 1969. Even prior to passage of the Act, strong reaction was quick to arise concerning the effect of such legislation upon the coal mining industry. Initial response varied from mild forms of criticism to' the expressed fear of complete suspension of operations and mine closings. Primarily responsible for these early forms of skepticism were speculative or fanciful cost estimates which led operators to contemplate a less than prosperous existence. However, in spite of this unfavorable outlook, the majority of the operators have faced up to the situation and have been striving to comply with the Act and the regulations issued thereunder. While encouraging strides have been made toward implementation of the Act, it must be recognized that noticeable results have been attained only through many months of determined effort and, as anticipated, at quite heavy expense to the operator.

Jan 1, 1973

By M. Tamlin

The state of the lithium mineral industry is closely linked to the performance of the glass and ceramic industries and to the overall economy. Demand for the glass/ceramic products in Europe, Asia and North America remained strong during 1999. This was due to a slight improvement in the economy during the latter half of the year. Consequently, demand for lithium minerals was firm, with a positive outlook. The major economic minerals for lithium are spodumene, petalite and lepidolite. The latter was once the primary mineral. But its importance hasdeclined since the 1960s. The lithium industry consists of two different segments: •The lithium minerals segment mines from hard-rock deposits and physically processes the material to high-grade concentrates. •The lithium chemicals and metal industry segment. The major feedstock for specialty lithium chemicals was previously high-grade spodumene ore converted to lithium carbonate. However, most lithium carbonate is now sourced from salars in North and South America.

Jan 1, 2000

By Ross W. Whipple

Applying geophysical techniques in potential geothermal areas has received: little attention in the United States, though it is widely used and accepted in New Zealand and Italy. In those countries it has been demonstrated that geophysical surveys can be useful in locating new geothermal areas and in directing test drilling programs. Geophysical studies in a thermal region can provide structural information and, if conditions are right directly; locate subsurface hot waters. They can give indications of sub-alluvial rock types and of the thickness of alluvial cover. In certain cases they can be used to estimate the power potential of a hydrothermal system.

Jan 1, 1963

By John W. Ahlrichs, E. Daniel Baker, Erich U. Petersen, William J. Tafuri, Douglas N. Halbe

The combined Bootstrap and Capstone deposits, located in the Bootstrap subdistrict (Section 10, T36N, R49E, M.D.B.M., Elko County, Nevada), are approximately 27 miles northwest of Ca-1I: Nevada. The contiguous Bootstrap Capstone deposits are located along the northeastern and northern flanks of Round Mountain, a horst block separated by grabens from the sheep Creek Mountains to the north-northwest and the Tuscarora Mountains to the east. Open-pit-minable gold reserves as of December, 1989, were 13.27 million short tons with an average grade of .057 troy ounces gold per ton and an overall waste-to-ore strip ratio of 2.5:1. Ore zones in Bootstrap are concentrated along north striking high-angle dikes localized along faults, while ore zones at Capstone are strata form and structural, occurring at the Devonian limestone/siliceous sediment interface and in high-angle fault-filling dikes. Pre-ore faulting produced a complex structural setting for Capstone, dominated by strong northwest fault sets cross-cut by northeasterly structures. Alteration associated with both deposits is silicification with a-strong argillic overprint. Dike emplacement, which post-dates silicification, marked the onset of mainstage gold deposition and argillic overprinting of silicified lithologies. Gold displays an affinity for moderately argillized sedimentary and igneous lithologies. Mineralogic and geochemical analyses of rotary percussion drill samples show good correlation between gold, silica, antimony, and arsenic.

Jan 1, 1990

By Robert W. Miller

There are many problems faced by ventilation engineers in deep underground mining operations, not the least of which is controlling miner exposure to radon gas and its daughter products. Radon gas is commonly found in uranium mining operations, but may also be present in other deep metal mines. For example, tin mines in England, iron ore mines in Sweden, gold mines in South Africa, and molybdenum mines in the U. S. have potential radon exposures. This is because uranium and accompanying radium ore are ubiquitous to the earth's crust albeit at low levels. The fact that the activity represented by one WL can be caused by a relatively low concentration of radon gas increases the difficulty of control. Since the source of the radon gas is usually widespread throughout a mine, local exhaust ventilation is not a viable control schema. The technique used to control exposure is then dilution ventilation and, in fact, huge amounts of air must be moved in order to reduce potential exposures to an acceptable level. An interesting comparison can be made of ventilation rates in different types of mines. It is estimated in modern coal mines, which are generally acknowledged to have high rates of ventilation, that about eleven tons of air are moved for each ton of ore mined. A typical operating uranium mine may have ventilation flows of 14-15 tons per ton of ore mined. This provides an idea of the scope and importance of ventilation in modern mining operations where radon is a hazard. Further pressure is put on ventilation engineers by the steady downward trend in exposure limits set by national and international standard setting agencies. Much of this tendency toward lowered standards is based upon longitudinal mortality studies of miner populations. Another important factor is the limited number of experienced miners available in the labor pool. For optimum production, it is important to have as many experienced miners underground in each shift as possible. However, the average daily exposure in a U. S. mine must be less than .3 WL to permit the miner to work underground for a full year. The ventilation system then must provide enough uncontaminated air to maintain the WL below the .3 TTL level to maximize production efficiency and minimize personnel turnover and the problems associated with it. Ultimately, the goal of the ventilation engineer and health physicist is to protect the working miner from harmful exposures based upon currently acceptable standards. U. S. Federal regulations require that in uranium mines all active work sites must be monitored every two weeks if they measure above .1 WL. Areas that have .3 WL ratios or higher must be monitored on a weekly basis until five consecutive weekly samples show the level has dropped below .3 WL. Also, exposure records must be kept for all individuals exposed to levels exceeding .3 WL. These requirements provide a strong economic incentive to have a ventilation system that minimizes exposure of any personnel. A good ventilation system requires careful planning, operation and backup in order to fulfill its mission of providing adequate clean air. Its proper operation also requires coordination with production personnel so it can be adapted as new areas in the mine open up and old areas are sealed off. The ultimate indicator of ventilation efficiency to control radon daughter exposure is, of course, monitoring working levels. Historically, this has been done using the Kusnetz, Tsivoglou, and Rolle's methods, among others. These methods all require cumbersome equipment and tedious calculations to obtain the measurements that results in WL. More important, however, they require a significant time lag between sampling and counting, typically 40-90 minutes. This time lag is, in fact, what can cause significant economic losses due to unnecessary downtime as well as high WL exposures. In a typical mining situation, a sampling technician using the Kusnetz method takes a sample, moves to the next location and takes another sample and so on. Forty to ninety minutes after the first sample, the technician will stop, run the activity count on the filter and calculate the WL. The technician may be one-half mile away or several levels removed from where the first sample was taken when it is counted. If the WL ratio is high the technician must then backtrack to the sample position. There are then two options. If the sample area is a working stage, it can be shut down or a second sample can be taken. If the first alternative is chosen; i.e., shutdown and correction of the ventilation, then another sample must be taken, followed by a forty minute wait for results. If the ventilation adjustment didn't correct the problem, then the whole process must be repeated with a minimum of forty-five minutes per sample cycle when using the Kusnetz method. It has been estimated from operating uranium mines that the cost per hour for downtime on a production slope is about $1,50O/hour. The time lag between sampling and resultant data can be very costly. If the second alternative is chosen to verify the first reading, the miners may be unnecessarily exposed to high levels while waiting for the result. Clearly, such a sampling system can be markedly improved by eliminating the excessive time lag between sampling and analysis.

Jan 1, 1981

By P. Moran

A promising and increasingly popular tailings management strategy is to place cemented tailings underground as backfill. The placement of cemented tailings results in enhanced geotechnical stability and a purportedly more geochemically stable tailings form with lower leaching potential. Conventional subaerial tailings management can negatively affect water quality if weathering causes acid rock drainage and metal leaching (ARD/ML) to occur, whereas cemented tailings can limit leaching via porosity and permeability reductions and contribute alkalinity to limit the potential for ARD/ML. Cemented tailings backfill appears to be better, but how can this advantage be proven? Currently, cemented tailings backfill is utilized at mining operations internationally, but there is limited guidance on performing geochemical characterization and associated evaluation of the potential impacts to water quality. As a result, various approaches to simulating the leaching behavior of cemented backfill have been utilized, including some methods that are unlikely to represent weathering under site-relevant conditions. American Society for Testing and Materials (ASTM) Standard Test Method C1308-08 is a diffusion testing method initially developed to assess constituent release rates from solid nuclear waste forms. ASTM C1308-08 uses intact cylinders that more closely represent actual backfill than methods that require crushing or size reduction. It is widely believed that leaching from actual cemented tailings is controlled by diffusion through small pores that exhibit limited exposed surface area, making diffusion testing particularly applicable to cemented tailings placement.

Feb 27, 2013