Search Documents

By Juan L. Yarmuch, Gonzalo Sepulveda

Medium- and short-term mine planning holds immense significance in optimizing production and resource utilization. It serves as a vital link between the long-term strategic plans and the day-to-day operational activities of a mine. In this context, a mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the net present value (NPV) of the schedule while ensuring enough room for the operation of mining equipment.

Jul 1, 2024

By S. Behl

A major limitation in developing successful selective flocculation schemes is the difficulty encountered in adsorbing the polymeric flocculant only on the desired substrate. In this paper a correlation between selectivity of flocculant adsorption and separation efficiency is outlined and a potential technique to achieve selective adsorption of flocculants is discussed.

Jan 1, 1992

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985

By S. Komar Kawatra, J. J. Carlson

"It is widely known that steel made from iron ore pellets high in phosphorus is brittle. Removal of phosphorus from iron ores such as hematite has proven to be difficult. The majority of research on phosphorus removal from hematite ores has been focused on flotation. The purpose of this study was to assess phosphorus distribution under current operations at an existing hematite concentrator and determine how efficient the plant is at removing phosphorus. Objectives included: (1) Perform a phosphorus balance at an operating plant to assess phosphorus distribution under current operations; (2) Determine phosphorus removal efficiency of each separating unit and (3) Perform a quantitative liberation analysis to determine max phosphorus removal by physical means. Liberation was quantitatively determined using wet high intensity magnetic separation (WHIMS) to separate iron ore from liberated apatite (and other nonmagnetic compounds).It was observed that 61.2% of the total phosphorus entering Plant F was rejected during current operations. The desliming process was the most efficient step at removing phosphorus (45.1% P removed), whereas the flotation step was much less effective (16.1% P removed). Liberation analyses indicated that the deslime thickener may have been more efficient at removing phosphorus than the flotation circuit due to the greater abundance of liberated phosphorus in the deslime thickener feed. The scavenger returns stream was identified as having a high concentration of phosphorus and a possible point of phosphorus removal. However, liberation analyses indicated that only 32.4% of the total phosphorus in the stream was liberated. Grinding the scavenger returns to 80% passing 5.2 µm increased the amount of liberated phosphorus in the stream to 70.4%."

Jan 1, 2014

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By D. Scott Scovira, Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1 ms increments up to 1500 ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits.

Feb 1, 2024

By C. V. Deutsch, O. Babak

A longstanding problem in geostatistics is that kriging usually assigns significantly greater weights to end samples in strings of data than it does to central samples. These weights are theoretically valid, but suboptimal estimates may result when there are geological trends in the variable near contacts, that is, large weights may be applied to samples that are systematically lower or higher than average. A number of ad-hoc corrections exist, each with pros and cons; none are fully automatic with a well-defined measure of optimality. A new method for estimation in a finite domain is proposed. This method is referred to as finite domain kriging. The method is based on kriging with a successively larger number of data. The total number of relevant data (n) is established, and then n kriging matrices are solved. The first matrix has the closest single data value (n-1 weights are set to zero); the second has the two closest data (n-2 weights are set to zero) and so on. The final matrix has all n data. The kriging weights used for estimation are the average of the weights from the n successive kriging runs. Each kriging run is optimal, yet with different smoothing and a different treatment of data at the end of the strings. The result is a set of weights that does not give undue influence to data values at the end of strings. The methodology is developed with examples. Cross validation shows that finite domain kriging outperforms conventional kriging.

Jan 1, 2009

By S. Tuylu, D. Adiguzel, A. Bascetin, O. Ozdemir, U. Cinar

"In recent years, use of mineral processing tailings as a paste backfill has been significantly increased due to the environmental problems occurred during the disposal of the tailings in mine area. The paste material used to fill the stopes excavated is generally consisted of tailings (solid ratio: 70–85%) and cement (3-7%w/w). Meanwhile, the strength of the paste material is completely related to ratios of these materials. Cemented Paste Backfill (CPB) system is used as support depending on the roof pressure and also as an underground disposal method. Therefore, temporary strength value of the paste material gains a great importance. For example, the paste backfill material must compensate the minimum 4 MPa strength value in order to procure the permanent fortification, and the mixture cost must be minimal as well. For this reason, in this study, the Pb-Zn tailings were used to prepare for the paste backfill material using cement in order to perform the uniaxial compressive strength (UCS) tests. Additionally, a statistical experimental design and linear programming techniques was used to find the optimum mixture in terms of strength and cost. The pulp solid ratios (PSR) of the tailings and cement (by the solid) were varied as 75-85% and 3-8%, respectively. The results of this study; the optimum mixture is ~79.5%PSR and 6.8% cement ratio (by the solid) for 4 MPa UCS (28 day) and 16-17 cm slump value determined by this method with statistically reviewed experimental data. INTRODUCTION Fine-grained tailing waste materials resulting from mining activities are an important environmental problem. In terms of environmental protection, the use of tailings with paste backfill is a very attractive approach and a desirable solution to tailings management. Paste backfill, which is used to fill underground openings, is made by primarly mine tailings mixed with hydraulic binders and water. Its main benefits are not only disposal of mine tailings in underground, but also providing a certain strength to ensure a safe working environment. Therefore, it is necessary to use hydraulic binders due to durability of the system (Benzaazoua et al., 2004). Paste backfill, formed from the mix of dewatered plant tailings (75-85 wt. % solids), water and binder (3-8 wt. %) (Brackebusch, 1994; Landriault et al., 2005).Water is used to determine the chemical reactions between tailing and binder materials for strength as well as increasing pumpability. Portland cement and ash can be used as binder materials (Douglas and Malhotra, 1987). The factors which affect strength and stability of paste backfill separate into two groups called interior and exterior factors. Interior and exterior factors determine the strength, stability and deformation features of backfill in short and long terms and also affect the transportation of backfill to underground (Benzaazoua et al., 2004; Erçikdi et al., 2006; Yilmaz et al., 2010; Nasir and Fall, 2010). Material properties of tailings as well as site operations to fill the underground openings are the most important steps for the design purposes. Grain size distribution, chemical, and physical properties of tailings, and mechanical properties of paste fill material are used to understand the suitability of tailings as paste fill material (Ozturk et al., 2014). In addition, Fig. 1. is also proposed to apply a typical design for the operational stages of paste fill applications on the site."

Jan 1, 2016

By James M. King

Analytical models for transient groundwater phenomena, such as those of Theis, Cooper, and Jacob, are important but often limited tools for aquifer evaluation and drawdown prediction. Most were developed using simplifying assumptions which compromise their treatment of complex boundaries and most also contain functions that are mathematically complex and difficult to solve explicitly. Examples of such functions are the Bessel functions, the exponential integral, and similar well functions for leaky confined and water table aquifers. This paper describes the joint use of simple numerical techniques and numerical approximations of these functions to extend many analytical models beyond their conventional applications. The enhanced analytical methods represent many hydrologic problems more easily and realistically, permit a wider range of application, and often provide insight into the response of pumped groundwater systems without the need to resort to more complex numerical flow models. Use of the enhanced analytical methods usually requires the use of microcomputers due to the large number of computations. Examples presented here are the development and extension of type curves and the determination of drawdown distributions.

Jan 1, 1984

By G. Davis

Mineral properties and mineral firms often trade at a market value that is significantly greater than the value indicated by discounted cash flow (DCF) techniques. A possible explanation is that DCF analysis does not consider the value derived from managerial flexibility. Presumably, then, at least some of the difference between DCF value and market value is due to managerial flexibility. This paper surveys the recent attempts to empirically quantify the value of managerial flexibility using option pricing theory. The results indicate that managerial flexibility, at least as measured by the option pricing methodology, falls well short of explaining the gap between DCF value and market value.

Jan 1, 1995

By P. A. Rittenhouse

Reserves of potash are more than adequate to meet future world demand for this primary fertilizer nutrient. The bulk of both reserves and current production is located in only a few countries. Recent attention has focused on potential development of smaller reserves to supply local markets in developing areas of the world. However, most new capacity in the next decade will be built in countries with large current production and reserves. The paper reviews current and future projects that will add to the world supply of potash.

Jan 1, 1985

By S. J. Jung

The prime criteria in the design of underground openings with complicated geological structures is ground control. Stability of underground openings for deep mines is critical because incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress conditions. Current design procedures for complicated orientation and geometry of mines are rapidly becoming inadequate as mines are being developed. In this study, finite element method has been used with optimization criteria to design more stable and safe underground openings.

Jan 1, 1993

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production; however, the thermal state of pellets in drying section is still unclear. In this study, the temperature distribution of drying section was investigated using computational fluid dynamics (CFD). Based on the calculated results of airflow velocity, space temperature distribution, and the temperature change of pellets, it concluded that there is a coupling effect in drying section in traveling grate. The gas with higher temperature in DDD transfers heat to UDD through the gap of the insulation board, and the temperature gradient of the pellet bed changed before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD was displayed in UDD in advance. Moreover, a contrast experiment was conducted to verify the model.

Feb 1, 2021

By Henrique D. G. Turrer, Robert F. Winterfield, Jobe E. Wheeler, Marcello R. Cru, Baojie Zhang, Pedro P. Pinto

Efficient particle classification is essential to enhance gravity and magnetic separation stages in one iron ore beneficiation plant. This study investigates the use of high-frequency screens to process finely ground iron ore, focusing on two size cuts: 400 μm and 100 μm. Pilot-scale trials were performed on four ore blends using a full-scale screening unit. A total of 48 tests were conducted, evaluating the effects of panel aperture, solids concentration, wash water, and feed particle size distribution. Results showed that wash water improved efficiency by up to 5%, while a solids concentration near 40% w/w delivered high separation performance with minimal ultra-fines in oversize streams. Apertures slightly larger than the target cut sizes yielded better precision in particle separation. Feed particle size distribution had limited impact on efficiency. The investigation successfully identified optimal screening conditions, including aperture selection, to achieve the most effective separation performance for downstream concentration processes.

Feb 22, 2026

By L. L. Damon

A geochemical study of cyanide neutralization processes was conducted at Brohm Mining Corporation to gain a better understanding of the leach pad behavior and to develop a simplified procedure to quantify the attainment of compliance with permitted cyanide neutralization criteria. Such attainment is a prerequisite for off-loading spent ore from the leach pad at the "load/unload" gold heap leach operation. The geochemical study program consisted of size fraction analyses and weak acid dissociable (wad) cyanide analyses for various sections of the spent ore from the actual leach pad. Further testwork included size fraction analyses and wad cyanide analyses on the ore from four 29 foot laboratory test columns which were leached and neutralized with different neutralization treatments in parallel with an actual active leach pad. Wad cyanide was analyzed daily on the neutralizing columns and various parameters were monitored weekly on the influents and effluents during the leach cycle and neutralization period. A comparison was made of neutralized effluent chemistry and porewater extraction fluids, as well as an analysis of the selective adsorption of cyanide on various particle size fractions.

Jan 1, 1992

By R. Yang

This paper presents a kinematic approach for blast modeling with examples of blast models that were developed previously. A kinematic approach was applied successfully in developing blasting models that can simulate all blast design parameters for field applications. Several applied blasting models have been developed and applied widely in the world. A kinematic approach to blast modeling refers to using measurements of kinematic quantities such as the velocity, strain, or displacement and well-established assumptions to model blasting phenomena, rather than being restricted to use first principal of physics, such as, the stress- and material-constitutive relations. The kinematic quantities are easy to measure in the field. Due to the complexity and inhomogeneity of rock mass properties, using first principles of physics, many parameters of rock and explosive properties must be involved, which are hard or impossible to quantify. This creates a major impediment when trying to simulate the total process of blasting based upon first principles of physics. The 3D kinematic model for muckpile formation was developed and applied to open pit blasts. The multiple blasthole fragmentation model developed during recent years has been applied successfully to many mine sites around the globe. These models are typical examples of blast modeling using the kinematic approach, which enables the models to catch major trends of the blasting process and explicitly simulate full blast design parameters and complex geometries. Blast modeling using the kinematic approach results in easy model calibration and validation against field measurements and effective applications to practical problems. Using kinematic models of the muckpile formation and the multiple blasthole fragmentation model, this paper demonstrates the merits of the kinematic approach for blast modeling. New developments of the models were also presented in the paper, which illustrate the potential of the kinematic modelling approach.

Mar 2, 2022

By H. E. Bonner

The recovery of fine coal has historically had limited success due to the intimate clay association on the surfaces of the coal particles. This clay presence has detrimentally affected conventional beneficiation techniques resulting in a recovered product containing unacceptably high concentrations of ash and moisture. An ultrasonically activated tray that operates in a continuous fashion has been developed that separates the clay film from each particle's surfaces. This separation is of sufficient duration to allow conventional beneficiation techniques to be utilized more efficiently.

Jan 1, 1989

By Brian Mangogna, Clay McNail, Weishi Mang, Adam Steimel

Together with innovatively applying modern flotation reagents and developing the breakthrough mill enterprise expert control and operating system, Doe Run Buick Mill constructed an advanced large copper rougher scavenger to process its complex Pb\Zn\Cu ore more efficiently. The scavenger circuit, featuring its own motor control center, air blower, multiple reagent loops and FrothSense+™ camera, operates both mechanically and chemically to maximize copper recovery and under expert control. Such scavenger features can be applied to zinc rougher circuits for all Doe Run mills to maximize Cu recovery during Cu special runs when the zinc rougher becomes a copper rougher scavenger.

Feb 1, 2025

By Günther M. Volkmann

"INTRODUCTION The construction of the BAB 44 motorway between Kassel and Herleshausen (both Germany) is an important part of the trans-European road network. After its completion, the A 44 will permit an efficient connection of the Benelux States in the West and Poland in the East. In the section between Eschenstruth and Hessisch Lichtenau the Hirschhagen Tunnel is constructed with a length of 4.1km. Most sections of the tunnel are situated in weak ground conditions. Hence a combination of face bolts with spiles (short forepoling) or pipe umbrellas (long forepoling) additionally support the tunnel heading on a regular basis This article will focus on the application of a newly developed method to connect the pipe umbrella support, which is mostly installed by conventional drilling machines nowadays. The installation method limits the outer diameter to a maximum of 168mm and a pipe wall thickness of 12.5mm because workers must be able to handle pipes and its drill steel. Typically these pipes are connected with threads that create a weak link in the support system so during the last decade alternative connection systems were developed to overcome this disadvantage. One of these alternative coupling systems is the so called Squeezed Connection, which will be explained in this article followed by a discussion of its advantages and disadvantages regarding technical specifications, construction time, and safety issues. THE HIRSCHHAGEN HIGHWAY TUNNEL The German highway A 44 directs from Aachen through the Ruhrgebiet to Kassel (all Germany) and it is extended to Herleshausen (Germany). The new section connects the A 7 to the A 4 after completion. This upgrades the east-west highway connection starting at the Benelux Union and heading to Poland so it is an important part of the trans-European road network. The newly constructed section has a total length of approximately 63 km and comprises 13 tunnels. All tunnels are constructed as double tube tunnels with 2 lanes and emergency sidewalks on both sides and 14 emergency cross passages. The Tunnel Hirschhagen starts in the north of Eschenstruth and ends near Hessisch Lichtenau (Figure 1). The length of the northern tube is 4,147 m and that one of the southern tube is 4,204 m. So it is the longest tunnel of the A 44 and the second longest highway tunnel in Germany when it is put into operation. On its alignment it crosses underground the Losse valley with the state road 7, the streetcar Kassel-Hessisch Lichtenau and the Losse stream. The cover above crown varies from 10 m to 95m and it is the lowest when crossing the Losse stream."

Jan 1, 2016