Search Documents

By R. D. Lopez

The concept of "heat recuperation" for the grate-kiln pelletizing system was first implemented at the Sydvaranger plant in Norway in 1974. Essentially, heat recuperation involves bringing hot air from the second stage of the pellet cooler to the drying zone to increase drying-air temperature to the maximum limit. 'Burner-fuel savings result from a lower kiln secondary-air mass flow at a higher temperature. Because of the fuel benefits achieved at Sydvaranger, heat recuperation has been included innumerous new grate-kiln plants built since then, and some older plants have been retrofitted for heat recuperation. In recent years there has been much confusion about the fuel benefits of heat recuperation. To answer some of the questions, a mathematical model was developed and plant tests were conducted at Minntac Phase 111. Minntac is a magnetite taconite concentrating and pelletizing plant, and Phase III has two indurating lines. This paper presents the results of the studies and plant tests.

Jan 1, 1980

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By Edward C. Dowling

Dilbert, management mumbo-jumbo, and human resource buzzwords aside, this paper defines corporate culture and why it is important to understand it. The sum of company experience, both good and bad, defines the way people work together. This integration of experience outlines the expected behaviors, or culture, in an organization. Given the competitive pressures inherent to our industry, the dizzying ongoing industry restructuring, and the recognition that behaviors drive effectiveness, the appreciation of an organization's culture is a prerequisite to meaningful improvement, particularly for those organizations undergoing growth, acquisitions, or mergers.

Jan 1, 2001

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

By İbrahim Alp, Emine Yoğurtcuoğlu

This article includes the application of roasting pretreatment by assisting the cyanidation process in the recovery of Au–Ag from Bolkardağ Gossan refractory ore and the characterization studies of the ore, roasting sample, and postcyanidation waste sample. While ore contained many metals along with gold and silver, the environment in which these metals were found was carbonate, sulfated, silicated, and iron oxide-containing deposits that have undergone oxidation. In mineralogical studies, there were Fe oxy/oxyhydroxides, Pb/Zn carbonates, and jarosite-bearing structures such as beudantite, calcite, dolomite, clay, and quartz in the ore. The sample used in the experiments was d80 = 29.6 μm, and the test parameters were determined by examining the TG analysis made to the ore. Preroasting experiments were carried out at a roasting temperature range of 200–800 °C, during a roasting period of 10.0 min. Three different samples were characterized by TG for temperature changes, FT-IR for bond structures and permeability, SEM/EDX for visual inspection of structural changes, and XRD Rietveld’s analysis for mineral % content differences. As a result of the cyanidation experiments carried out after the pretreatment, gold was recovered with 80–90% yields and silver with 40–48% yields, respectively.

Aug 21, 2023

By Arthur B. Johnson

Potassium, is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production. Potash is found throughout the world in both soluble and insoluble forms. It is only the soluble forms that are economically attractive to process, primarily chlorides and sulfates, with potassium chloride by far the most important potash salt. Sylvinite ore, a mechanical mixture of sylvite (KCl) and halite (NaCl), is a natural mineral of potassium. This ore is found in commercial quantities in the Permian sin region near Carlsbad, New Mexico. Vast tonnages of high-grade de, low-clay-content ores have been mined and concentrated during the past 40 years; however, these deposits are rapidly being depleted leaving high-clay, low-grade ore reserves of over 135 million tons. These ores, containing 13 to 22 percent K20 and 3 to 8 percent clay slimes; cannot be effectively processed by current commercial flotation methods. The present concentration processes for potash minerals in Carlsbad relate mainly to ores containing 1 percent or less of clay-slimes with a K20 content of 20 to 25 percent to yield products to meet the requirements of the agriculture market, namely, 95 percent KC1 equivalent to 60 percent K20. Discoveries of potash ore in Saskatchewan, Canada, have shifted the emphasis on expansion outside the United States. Presently, the American companies are looking to Canada for future growth, expenditures, and expansion. Four of the seven companies operating near Carlsbad are produces of Canadian potash despite the large investment sons required for shaft sinking and milling installations.

Jan 1, 1970

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By D. G. Chedgy

This article presents a novel design, called the Climax High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 -660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Jan 1, 1997

By Y. C. Lo

This paper presents the development of ultrasonic grinding technology for material and mineral processing. The principles underlying this new technology, as well as their implementation in two laboratory scale devices are described in detail. Ultrasonic grinding experiment results are discussed with respect to operating variables and the achieved product sizes. Special attention has been given to the electrical energy consumption of the grinder, and an attempt to compare its efficiency with tumbling mills has been made. A mechanical system capable of measuring the specific grinding energy is also described.

Jan 1, 1991

By D. A. Wheeler

Invented by Pierre Boutin in the early 1960s the column was a complete break from the conventional flotation cell. 1. When used as a rougher-scavenger, the column is excellent. 2. When used as a cleaner, the results can be spectacular. The very first column tests were carried out using it as a rougher-scavenger in a reverse float where silica was floated from iron. It produced a concentrate underflow as good or better than that produced from roughing and scavenging stages in cells, The froth tailing overflow was better than that produced by several stages of cell cleaning. Column scaleup progressed rapidly from the two inch diameter unit to a semi automated 12 inch diameter column on material from the Iron Ore Company of Canada. A change in operating philosophy within IOCC brought all flotation development, column or conventional, to a halt. At that time, IOCC had an exclusive right to the use of the column in Canada in the field of iron ore. We moved into the field of sulphides. A Canadian copper producer sent ore for testing and the results led to their purchase of the first commercial size of column - a 36 inch diameter machine. It was a mechanical disaster. It took several years to raise sufficient funds to return to that mill with our basic 18 inch square unit. It was to be tested and modified in order to learn how to properly design a large column. Originally used as a rougher- scavenger, it had to produce tails equal to the final tailings from this well run plant. It did, and did so while producing a rougher-scavenger concentrate almost equal to the plant final concentrate. It was finally used as a cleaner and produced concentrate 5% higher in copper than the plant final concentrate with equal cleaner tails. This phase of the column development was carried out under very difficult circumstances. The mill superintendent had realized that if he took the froth removal system from our original mechanical disaster and applied it to a conditioner while injecting air, he would have a flotation cell. He had personally applied for patents on this Maxwell Cell. Our development work was done in his mill and as our results became better and better, our difficulties became worse and worse. We finally had to terminate this work. The 18 inch column installed at Mines Gaspé 14 years later was identical to the one removed from Opemiska. The 18 inch column was tried on various ores over the following years and always produced excellent results. However, it was not really a production size unit. We had always aimed for the 72 inch column (72" x 72" x 44' 9"). Prior to this huge machine, we needed the intermediate 36 inch column. The failure of the original 36 inch diameter unit at Opemiska had raised the possibility of short circuiting inside the column as the cross section increased. The first 36 inch square unit was tested in parallel with the proven 18 inch column. If the underflow of the 36 incher was not as good as that of the 18 incher, short circuiting was a possibility in the larger unit. It had been designed for insertion of drop in partitions, four feed points had been provided and the 36 inch column would have become a modular unit of four 18 inch columns. Testing showed the underflows of both columns to be identical. There was no short circuiting in the 36 inch column. Once we had the 36 incher, we had no fear of the 72 inch column. It is permanently partitioned into four 36 inch columns but uses only one set of instrumentation. All the component parts of the 72 inch column come from the 36 inch unit. In spite of our results, the mining community did not believe the column could work. Finally, in 1980, Mines Gasp6 ordered an 18 and 36 inch column for their byproduct molybdenum

Jan 1, 1988

By J. J. Kellar

The near-infrared (NIR) (12,000-4,000 cm-1) region of the electromagnetic spectrum, between the mid-infrared and visible, has often been viewed by spectroscopists to be of limited utility. This is unfortunate, and recently the use of the NIR has increased greatly, primarily for the quantitative analysis of food and agricultural products. However, many other areas of application of NIR spectroscopy remain unexamined. In this paper a novel use of NIR in the area of flotation chemistry is demonstrated. Specifically, it is shown that NIR/Internal Reflection Spectroscopy (IRS) can be used to quantify collector adsorption reactions in-situ.

Jan 1, 1990

By M. L. Young

Hindered settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous, laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate, and column height column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 1999

By Dennis C. Parker

The Porters Creek clay is mined for its absorbent properties. The formation is part of the Upper Mississippi embayment and is recognized in Alabama, Mississippi, Tennessee, Kentucky, Illinois, and southeast Missouri. Major minerals in order of abundance are Montmorillonite, Quartz, Illite, Kaolinite, and Chlorite. Mining consists of open pit operation utilizing track loaders or scraper. The clay is dried or hardened in rotary kilns and crushed to size by roll crushers. The clay granules are sized and air classified prior to storage for shipment or packaging. Granules are sold for pet absorbents, oil absorbents, anti-skid material, fertilizer, and pesticide carriers.

Jan 1, 1979

By F. J. Susko

The U.S. Bureau of Mines is using Fourier-transform infrared (FT-IR) analysis to investigate the bonding mechanism which occurs during the dewatering of clay slurries. High molecular weight polymers are used as flocculating agents in these processes. This investigation presents the results of an FT-IR study of calcium-exchanged montmorillonite treated with polyacrylamide (PAM) and polyethylene oxide (PEO). Both thin film and attenuated total reflectance (ATR) spectroscopic techniques were employed to study this clay-polymer system~ Results suggest PAM is adsorbed to the clay via the nitrogen atom of the polymer. A water bridge is involved in the bonding between the clay and PE~. Evidence also suggests that PEO may be adsorbed directly onto the surface of the clay.

Jan 1, 1990

By K. Peri

The leaching behavior of gold in ammonical solutions with iodine as an oxidant has been investigated using cyclic voltammogram and Tafel polarization. The majority of experiments was carried out at 75°C and the results were compared with the equilibrium consideration on the iodine-ammonia system. The distribution of nine iodide containing species at various pH values in the absence and presence of ammonia was considered at three different temperatures. It was found that by introduction of ammonia into the system, the concentration of iodide (r), iodine (12) and triiodide (13') is increased substantially which in turn helps the rate of dissolution of gold. The apparent activation energy was found to be about 46 kJ/mole, indicating a chemical controlled mechanism.

Jan 1, 1999

By Ernest Y. Baafi

The usual tasks performed by a mine store include .removal, replenishment, ordering and deletion of items and updating of stocks. A personal computer Mine Store Inventory Database System MIDSYS for monitoring stocks in such a store is presented. The system consists of series of relational databases developed in dBASE III+ environment. The system has three main modules comprising of a store management module, a display module and an employee-store operation module. The third module is useful in tracing movement of store goods. The MIDSYS is menu .driven with help functions at all levels.

Jan 1, 1992

By James J. Scott

Three dimensional photoelastic techniques have been developed which provide information on the state of stress at any point in a model investigated. This investigation utilizes these techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by use of data obtained by observing points in slices from the model with a polariscope and solving data obtained by' the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. Results of this work provide information on the overall stress distribution on points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type.

Jan 1, 1963

By C. C. Harvey

As we move towards the 21st Century there are several factors that will influence the markets and processing requirements for industrial minerals. Traditional markets for many industrial minerals in the developed world are frequently stagnant or decreasing because of their maturity or due to environmental factors such as reclamation, recovery of byproducts, and recycling. Some industrial minerals are greatly affected by these factors, while others are either immune to or have adapted successfully to meet these challenges. In the developing countries of the world, there is rapid market growth and resource exploitation. The future of specific mineral commodities in several markets will be discussed.

Jan 1, 1997

By Osamu Shoji, Mamoru Kato

In order to continue improving the quality of telecommunication services to meet the expectations of the people and to increase reliability in the case of emergency such as disasters, Nippon Telegraph and Telephone Public Corporation (NTT) is now constructing cable tunnels which connect main urban telephone offices. However, almost all the large cities in Japan are built in river deltas, so that their chief underground features are low strength fluvial deposit and a high ground water level. In this saturated soft ground, the ground surface at an installation site has occasionally subsided through deep excavations for cable tunneling construction. As these settlements have sometimes caused accidents, especially in densely populated large cities, NTT has made much effort to avoid such accidents. These accidents have occured mainly in flexible sheeting due to its inward movement. Therefore, after the investigation into forecast method of sheeting deflection with accuracy, NTT has reserched a system which forecasts ground surface settlements. This paper describes an outline of the ground settlement forecast system and practical example on the site.

Jan 1, 1979