Search Documents

By Andrew Thomson, Peter Wright

"A section of a London Underground expanded segmental lined tunnel constructed in the 1970’s progressively deteriorated after 2001, with extensive radial joint spalling and mid-segment cracking. As part of the PPP contract Tube Lines Ltd and their partners carried out various analyses of the tunnel, including analysis of laser scans of the tunnel, geotechnical testing through the tunnel walls, geotechnical desk studies, real-time monitoring and even full-scale segment testing. This paper discusses the behaviour of the tunnel lining in this setting, the causes of failure and the lessons that can be learnt from this rare example of a tunnel which was progressively failing in service. It is finally noted that a replacement tunnel lining was installed during night-time possessions and completed in 2015. INTRODUCTION In 2003, Tube Lines Ltd. was established under a Public-Private Partnership (PPP) scheme to provide maintenance services and upgrade projects for London Underground (LU). The Deep Tube Tunnel Knowledge and Inspection Programme comprised the assessment of all tunnels, shafts and other underground structures. This included a number of lengths of tunnel constructed using segmental concrete linings. First used by LU in the 1960s, the savings both in cost and speed of construction led to concrete linings replacing cast iron for new tunnel construction in all but a few cases. During the initial scoping phase of this programme, inspections identified potential issues with the expanded concrete segmental linings on the Jubilee line. The inspections found a number of segments with surface spalling (Figure 1a), which did not appear on the post-construction defect records. These were generally relatively shallow, up to 40mm deep, spread over a wide area of segment. These were different to spalls caused by handling damage, which are typically localised at segment corners. Subsequent inspections over the following years identified an increasing number of segments with these types of spalls as well as an increased incidence of longitudinal mid-segment cracking (Figure 1b). The increasing occurrence of these defects was hypothesised to be caused by tensile stresses developing in the vicinity of the joint."

Jan 1, 2016

By Sumit Kumar Hota, Asadi Srinivasa Reddy, Ashok Kumar, Ashish Agrawal, Surajit Sinha, Chandra Sekhar, Tanay Ray

In the current operational facility, due to the absence of pellet pot facility, a novel technique is developed wherein the pellets with different chemistries prepared in the laboratory are fired in an induration machine by placing them inside the Inconel baskets. In the present work, an attempt is made to optimize the pellet chemistry by developing 2 different flux pellets, viz., low basicity (B2: CaO/ SiO2 = 0.3) pellets and high basicity (B2 = 0.9) pellets, and further the effects of basicity on pellet properties, viz., cold compressive strength, porosity, swelling index, reducibility index, and softening and melting temperature, are studied. It has been found through the multiple operational trials that increasing the basicity of pellets from 0.3 to 0.9 results into improving the pellet strength, reducibility and softening and melting characteristics. Moreover, it is observed that the swelling index of pellets is reduced by adding 2% MgO to both low and high basicity pellets that could be attributed to the formation of high melting point slag in pellets. The operational trial has resulted into producing pellets that exhibit a combination of desired mechanical strength, improved swelling, and reducibility index and possess better softening–melting behavior among all the chemistries studied.

May 24, 2022

By J. J. Scott

As a Rock Mechanics investigator, the author has, Over his career, attempted to use his best knowledge in developing better rock control fixtures. Based on the experience of nine years of development of friction rock stabilizers, in 1980 he decided to launch a new investigation to develop a unique roof support fixture which would fit the coal mining market. The largest single user of roof bolts in the world is the American coal mining industry, historically using up to 100 million fixtures per year. In 1989 they used approximately 82 million fixtures.

Jan 1, 1990

By John R. Marks

Introduction An engineer is a builder and a problem solver. He uses knowledge of the properties of matter and energy to furnish the needs of society. Engineers form the bridge between scientific researchers and the general public, most of whom are technologically illiterate. Mining, metallurgical, and petroleum engineers extract minerals from the ground and process them into usable forms. Then, other engineers further process them into society's needs. Minerals engineers deal with more uncertainty than other engineers. Each ore deposit has its own personality and each ore is metallurgically unique. Minerals engineers, therefore, must be flexible, often applying larger safety factors and contingencies than other engineers, and frequently functioning as a jack of all trades. A minerals engineer can work in coal, oil, oil shale, base metals, ferrous metals, precious metals, industrial minerals, strategic minerals, or in exploration. Other mining jobs include banking and financing, education and research, marketing and sales, and government. As a minerals engineer, you may be among the first to work on the ocean floor or the moon. College Preparation A difference between college and industry is the type of problems to be solved. A typical college problem has an exact answer derived from given information. An industry problem is more apt to have a solution chosen from a number of alternatives. Information required for the solution is not given. It must be measured, calculated, looked-up, estimated, or otherwise derived. Solutions involve trade-offs, economics, and human factors, as well as application of physical laws and theory. When a college problem is answered, you move on to the next one. In industry, however, the headaches may just be starting with the implementation of the solution. Students often complain that they see little use for the theory they are learning. This is valid. A good professor will link theory and practice. Another difference between college and industry is the price of failure. In college, you can make a half-hearted effort in an assignment and take your C or D. On the job, however, poor engineering results in potentially effective projects being rejected and unsound projects being undertaken. Poor performance results in cost overruns, schedule holdups, oversights, disgruntled employees, irate bosses, unsafe structures, and unreliable systems. The costs are time, money, and possibly lives. The student pays the university for his work - not the other way around. So the rewards for good schoolwork often seem nebulous. But education must be viewed as an investment. Working for good grades will help you think better, learn more, receive better job offers, and perform more effectively on the job. There is no substitute for hard work. Avoid taking the easiest electives. If you desire a more liberal education or dislike rigorous physical sciences, mathematics, or engineering courses, change majors. Remember, you are training to be an engineer, not a computer programmer or market analyst. At least one summer of industry employment is necessary for minerals engineering students. The sooner you gain actual experience, the sooner you will know whether to change majors. Most large companies hire students during summer. It is best to send out applications around Christmas break. First and second year students usually work as laborers. Upper-classmen may work as engineering technicians. Students must sometimes choose between returning to a company at a higher position or trying a different company at a lower position, for more varied experience. Both alternatives have advantages. Do your best on these summer jobs. The company is watching. If you do well, the chances are good you will get a job offer when you graduate. Good references are important when you begin job hunting. Interviewing occurs near the end of your school career. The standard procedure is to send your resume with a cover letter to each company you are interested in. The resume for a graduating engineer with little experience need not exceed one page. The cover letter must be written for the individual company.

Jan 2, 1985

By Florian Festge

It has been said that good things come in threes. In the case of screening for mining and quarry operations, profit comes in three distinct phases: layered, basic and sharp screening. But how good they are ? whether they maximize efficiency and improve the potential for success ? depends on having the right screen media on the deck for each of the three phases. A relatively new method for achieving that goal is a blended screen media approach that incorporates the ideal screen media for each phase and the ideal mix of media for the process overall. The goal in implementing a blended solution is to find the optimal combination of open area and durability. If this combination is found, maximum product quality and profits will be realized by increasing efficiency of classification while minimizing downtime and maintenance costs.

Jan 1, 2012

By George A. Roche

Since our firm was established by Mr. Price in 1937, we have followed an investment philosophy which is based on the belief that investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria that we use to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of our investment strategy for two of the three mutual funds sponsored by the Price organization and for our private clients. However, during the past 5 years we have seen inflation accelerate due to a variety of factors including the inability of our government to meet seemingly unlimited needs with limited revenue sources. While there might be temporary periods of price stability, we believe that inflation will still continue to be the investor's greatest problem in future years. Our conviction that inflation would increase combined with the acceleration of inflation in the late 1960s stimulated an intensive investment research effort, on our part, to identify those companies with strong natural resource bases -- who own or control large, secure, and low cost tangible assets. Over the longer term and in an environment of a depreciating dollar some of these firms should be able to develop and sell these assets at higher prices. While we still believe that investing in growth companies is a sound investment strategy to offset inflation, we also believe that certain natural resource companies will show well above average investment performance. In the newest Price mutual fund, The Rowe Price New Era Fund, we have, as a matter of policy, placed a large portion of the portfolio in natural resource companies.

Jan 1, 1972

By V. H. Forsythe

Mr. Chairman, members of SME, and guests It is indeed a pleasure to have the opportunity to appear before this group. The topic of this paper is, "Current Trends in Related Industries and Their Influence on Electric Shovel Design and Size". Before getting into the major items, it is well to point out that this text will deal with loading shovels primarily, since their application is almost universal in major open pit mining operations throughout the world. Related industries influence our design in many ways. For the sake of simplicity, these industries will be broken down into two major categories. The first category to be discussed will include industries that will indirectly influence design and size, while the second category will include industries whose products can directly be incorporated by the engineer in the design of shovels.

Jan 1, 1964

By Northcutt Ely

My topic today is our Nation's interest in the minerals beneath the oceans. I will state what I think should be our objectives, the means available to attain these objectives, and the obstacles to their accomplishment. It is possible that as early as this year of 1969 our country must make policy decisions on this subject, and that these, once made, will be almost irreversible. Two factors are hastening an. early decision. First, the 1958 Convention on the Continental Shelf becomes eligible for amendment after June 10, 1969, if the Assembly of the United Nations so decides. Second, the United Nations has created a permanent committee of 42 nations, which was preceded by an ad hoc committee of 35 nations, to study the question of the peaceful uses of the seabed "beyond the limits of national jurisdiction. While these measures purport to deal with the creation of a regime to govern mineral development on the deep sea floor beyond the limits of the jurisdiction of the coastal nations, it has become clear that the urgent issue is the extent to which this future regime shall acquire jurisdiction over the mineral resources of the continental margin, and receive royalties therefrom. This brings the proposal into potential collision with the interests of the coastal nations under the 1958 Convention on the Continental Shelf, including, of course, the United States.

Jan 1, 1969

By W. Szymanski

The United States contains one of the world's largest reserves of uranium. Domestic production and exploration activities, however, have declined since the early 1980s due to weaker-than-expected growth in nuclear power demand and to foreign competition. The main result has been that more costly and less productive conventional mines and mills have closed. Meanwhile, industry productivity as measured by uranium output per employee has increased threefold since 1980. At the end of 1992, only six plants, all nonconventional, were operating in the United States. Due to cost considerations and increased environmental awareness, any additions to existing capacity are expected to be met through nonconventional in situ leach plants.

Jan 1, 1994

By L. M. Yokum

Tremendous strides have been made in front end loaders in the last fifteen years. Fifteen years ago a 2; cubic yard front end loader was the largest standard machine you could purchase. Today there are two commercially available 15 yard front end loaders and many 10 yard front end loaders. The estimated total worldwide market for all front end loaders over one cubic yard has increased to over 30,000 units yearly. The trend for front end loaders, in general, and for the mining market, in particular, is to larger and larger loaders. Today there are 18 cubic yard and a 24 cubic yard front end loader in prototype form. It is not inconceivable that within another fifteen years that there will be front end loaders in the 50 cubic yard class with design features quite different from today's. These larger loaders are being designed at the demand of the mining industry and the design criteria are being directed at this market area. The costs of these larger loaders will be greater per unit of capacity, and it is the intent of the various manufacturers that they will be more reliable, be easier to service, give greater availability, live longer, and cost less to maintain, than previous loaders. It is also the intent of the manufacturers to compete directly with the large mining shovel as the front end loaders become appropriately larger and more reliable. There has been some trend in this direction in the past with smaller shovels and loaders. In Figure No. 1 are data for U.S. production of front end loaders (5-6 cubic yard class and 10 cubic yard class) and U.S. production of cable operation, crawler mounted power shovels, draglines and cranes (1; to 5 cubic yard class) for the years 1965 and 1970. (Source: Bureau of Census, U.S. Department of Commerce.)

Jan 1, 1972

By Steve Kral

The dramatic rescue of nine Pennsylvania coal miners trapped nearly 90 m (300 ft) underground for77 hours probably would not have happened without the high technology equipment and improved mine rescue training techniques available today. By now, most everyone has heard the story of the accident that occurred at the Quecreek Mine near Somerset, PA. At about 9 pm on Wednesday, July 24, the miners were drilling coal in the room-and-pillar mine. Their drilling accidentally punched through to the adjacent, abandoned Saxman Mine. Old mine maps of the Saxman Mine led Black Wolf Coal, Quecreek’s owners, to believe they were between 60 to 90 m (200 to 300 m) away from the abandoned mine. Those maps proved to be inaccurate.

Jan 1, 2002

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

"Foreword by Ren BryceSenior engineer, Freeport-McMoRan, Oro Valley, AZ, USAThe eighth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the national SME Annual Conference & Expo in Denver, CO. A total of 33 students presented their work at the poster competition. The competition started in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. The MPD recognizes the effort required to enter and as a result, provides monetary rewards to all participants. The first-place winner receives $1,000; the second, $500; the third, $250; and the fourth through seventh, $200. All remaining students receive $100. All of the students also receive a complimentary ticket to the MPD Luncheon. As in past years, there are separate levels of competition for undergraduates and graduates.Graduate winnersKaustubh Shrimali won first place for researching “The influence of starch in amine adsorption by quartz in the reverse flotation of iron ore.” Venkata Atluri received second for studying “The effect of polysaccharides on bubble attachment at talc surfaces.” Jennifer Galvin placed third for investigating “A novel approach to alkali pug bake for the extraction of rare earth elements from monazite concentrate.” In the fourth through seventh places were Amy Richins, Sumedh Gostu, Brett Carlson and Chris Vass.Undergraduate winnersNestor Santa earned first place for exploring “Copper recovery from waste printed circuit boards.” Cassidy O’Connell received second place for conducting “Performance analysis of CMC in high talc copper sulfide flotation systems.” Catalina Vanegas won third place for examining “Cyanidation tests and pretreatments to recover gold from a refractory ore in Colombia.” Kylie Boyce, Michael Archambo and Pritam Sinha were in the fourth through sixth places.Everyone benefits from attending the student poster competition. The students are able to display their work to future employers, and industry professionals can talk to up-and-coming engineers. Next year, there will be another competition for more posters and networking. Come and enjoy the event and the posters."

Jan 1, 2017

By Robert E. Baker

Cortez Gold Mines, the United States' third largest primary producer of gold, commenced continuous operations on January 10, 1969. The decision to proceed to production was made in March of 1968 and construction of the mill and stripping operations for the pit began in April and July, respectively. Anomalous conditions on the slope of Mt. Tenabo along the Roberts Mountain thrust fault zone were discovered by the U.S.G.S. while conducting geochemical surveys in the old Cortez silver district. Following the discovery of gold an intensive program of drilling was organized. Drilling outlined an orebody with 3.5 million tons of ore averaging 0.28 ounces of gold per ton. It was on the basis of this reserve that a 1700 t. p.d. cyanide plant was designed. Needless to say, with such a limited ore reserve, economies in design and construction would have to be observed. Cortez Gold Mines is a joint venture with American Exploration & Mining Co., The Bunker Hill Company, Vernon F. Taylor, Jr., and Webb Resources, Inc. , as partners. American Exploration & Mining Co. is the operating partner.

Jan 1, 1969

During the last 20 years, more than 80 km (50 miles) of tunnels have been constructed in the Los Angeles, CA area. Recent projects include The East Central Interceptor Sewer (ECIS), completed in 2004. It spans more than 18 km (11 miles). The Northeast Interceptor Sewer (NEIS), completed in 2005, spans 11 km (7 miles). And the 2-km (1.3-mile) Metropolitan Transportation Authority?s Gold Line Eastside Extension (MCGLEE) was completed in 2006. All of the tunnel routes lay beneath heavily populated urban environments so minimizing ground surface settlement was critical to the success of the projects. Previous tunneling efforts in the Los Angeles area using open shield methods resulted in significant settlement that damaged roads, utilities, buildings and other structures. Earth pressure balance (EPB), or slurry machines, were specified for these projects to reduce subsidence risk. The contractors chose EPB tunnel boring machines (TBM) for the work. The closed and pressured face of the EPB TBM reduces loss of ground at the tunnel face and, when the machines are used in combination with gasketed pre-cast tunnel liners and backfill grout behind the installed segments, losses from over-cut of the excavated surface are also reduced.

Jan 1, 2008

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device. Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery. Recent developments-in electrooptic inspection of dry end wet material leaving a grinding device are critically reviewed. New methods for characterizing ultrafines are discussed. A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine index and other fineness indices is described.

Jan 1, 1983

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof (XP) enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4) air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway (TR). Researchers at the National Institute for Occupational Safety and Health (NIOSH) measured TR pressures of lithiumiron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 294 bar (4260 psia) of pressure during a TR, far exceeding minimum pressure containment specifications for conventional XP enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce TR pressures to levels below that expected for CH4-air ignitions. Measured TR temperatures were below the minimum autoignition temperature of CH4-air.

Nov 6, 2020

By D. S. Yantek, R. J. Matetic, A. K. Smith, E. D. Thimons, J. Srednicki

In a 2007 report to the U.S. Congress, the Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) stated that built-in-place refuge alternatives (BIP RAs) provide significant advantages over mobile refuge alternatives. At present, the requirement to locate refuge alternatives within 305 m (1,000 ft) of working faces makes BIP RAs impractical in most coal mines. BIP RAs would be practical if three issues are addressed: (1) allowing BIP RAs to be located at greater distances from the working face, (2) developing a reliable process for the design and approval of BIP RA stoppings that meet the 0.1-MPa (15-psi) design criteria, and (3) developing systems that reliably deliver breathable air to the refuge alternative. In 2015, NIOSH OMSHR conducted a study of these three issues and issued a report. In the report, justification was provided for allowing the placement of BIP RAs at greater distances from the working face than the currently mandated 305 m (1,000 ft), guidelines were developed that could be used by industry when submitting BIP RA stopping design applications for approval which are patterned after the Mine Safety and Health Administration guidelines for coal mine seal design applications, and insights were provided into options for providing a reliable supply of clean, breathable air to BIP RAs. This paper presents a summary of the study’s findings and also addresses issues discovered during the building and designing of a BIP RA that OMSHR researchers constructed in NIOSH’s Experimental Coal Mine in Pittsburgh to research the testing and improving of BIP RAs. These issues include several issues related to the delivery, distribution and exhaust of ventilation air to the BIP RA and some general construction issues that require further investigation.

Jan 1, 2016

By G. Récoché, A. Chamaret, M. O’Connor

Building indicators that respond to all stakeholders' needs is a time-consuming and complex exercise, with certain questions still unsolved. The aim of the current three-year research project, carried out in partnership between BRGM’s Mineral Resources Division and C3ED, is to propose a top-down / bottom-up indicators building methodology that combines conception and coordination methods and a participative approach. The tool-design phase is based partly on a comparative analysis of existing international initiatives according to different criteria (objective, observation scale, framework, etc.). The study of two African mining projects will provide the opportunity to confront the conceptual aspects with reality in the field. Careful consideration of the participants’ suggestions will result in a set of indicators that can be easily understood and adopted by all stakeholders. The final objective is to measure the impact of a mining site on a local, regional and national sustainable development frame, throughout the full life cycle of a mine.

Jan 1, 2005

By Hakan Uyguçgil, Beril Bayraktar, Adnan Konuk

Mining is one of the industries with the highest risk of occupational accidents in Turkey and globally. The most important feature that distinguishes the mining industry from other sectors is the constantly changing working conditions. The risk of accidents is very high, especially in underground mining, and can happen for several reasons. Therefore, it is essential to carry out all necessary measures in coordination with other disciplines to adapt to changing workplace conditions. The dangers that might occur underground must be determined in advance, controlled at their source, or eliminated since it is critical to take the necessary precautions before the accident. Accident prevention will protect miners’ living conditions by contributing to the country’s economy through reduced labour and production losses. In this research, the data from 13,653 accidents reported in the Karadon Hard Coal Enterprise between 2000 and 2011 were analysed and compared using the Life Table and the Kaplan-Meier methods. Accident records were classified and analysed into four categories: environmentalrelated accidents, equipment-related accidents, person-related accidents, and other accidents. Findings in terms of survival time indicate that environment-related and person-related accidents had the highest risk in Karadon, with equipment-related accidents having the lowest. This study established the reliability of using survival analysis methods to investigate occupational accidents in the mining sector. Given that environment-related and person-related accidents occur in a relatively short period, such as 1 year after starting work, it has been recommended that research be done to improve workplace and occupational safety measures and broaden the training given to miners. Additionally, it has been determined that increasing the use of automation and mechanisation in underground coal mines, combined with developing a thorough equipment safety training programme to raise awareness of the danger, can help prevent person-related occupational accidents caused by the interaction between equipment.

Aug 5, 2023