Search Documents

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988

By Edward S. Plotkin, Thames F. Peyton, Gary A. Almeraris

This paper describes high speed tunneling by drilling and blasting in a heavily populated urban area. The project consists primarily of mining 2500 m (8237 ft.) of tunnel through mica schist, excavating three shafts approximately 200 m (650 ft.) each and concreting lining 5300 m (17,400 ft.) of 7.34 m (24 ft.) inside diameter tunnel. The techniques developed and equipment utilized to ensure a high rate of tunneling advance are described. Extensive planning and good communications were especially essential in maintaining production on this project since tunnel mining, tunnel concreting, and shaft excavation all proceeded simultaneously from one common work shaft and a single heading.

Jan 1, 1985

By Harry M. Conger

Good afternoon, fellow members of the international mining community. I appreciate the opportunity to participate in this special three-day, international gathering, and to join with you in honoring one of my very good friends, Doug Fuerstenau. It couldn't be more fitting to have this kind of event to mark Doug's 60th birthday. You know, in addition to his faculty position at the University of California in Berkeley, Doug is a member of the Board of Directors of our Homestake Mining Company. So it is a double pleasure for me to help pay tribute to one of the outstanding academicians of the mining industry as well as a man with whom I work closely in running Homestake. I have been asked to talk about "The Future of Precious Metals," but I will concentrate my remarks on gold. Since the theme of this Symposium is "Challenges in Mineral Processing," what I'm going to talk about is a challenge that relates especially to a major problem faced by those of us who process ores to recover gold. I noted that in the Scope of this Symposium, it stated: "the mineral industry is currently facing many challenges to improve the economics, operating efficiencies and environmental concerns of the mineral processing system." I couldn't agree more with that statement. I think that a need exists for us to address this situation as it involves gold. And who better to consider this than the worldwide leaders of mineral processing research here assembled. I start with the premise that we need a new method for cyanide use or a chemical to replace sodium cyanide entirely. In the case of using cyanide differently, I see a continuing difficulty in getting general public acceptance regardless of how

Jan 1, 1989

By Donna L. Boreck

Introduction Coal has been mined in the western United States since the mid-1800s. The resource is abundant in the West. Despite recent economic conditions, it remains an important part of the nation's energy warehouse. Many of the seams that comprise the western resource base are thick, some exceeding 61 m (200 ft). Multiple, closely-spaced seams or thick coals that split into two or more minable seams are also common. Historically, subsurface development recovered from less than 15% to 50% of these deposits (Matson and White, 1975). This resulted in a substantial loss of inplace reserve due to the limited height that could be mined using the available technology. In an effort to increase future recovery from such deposits, the US Bureau of Mines analyzed the potential for incorporating three thick-seam mining methods into western coal mines. These methods are high-face longwall, multislice longwall, and longwall caving. They were developed in Europe and are being used to mine thick coal seams in Europe and Asia. One aspect that will determine their success in the US is the geology of the individual deposit; namely, are the methods adaptable to the geologic conditions characteristic of western coal? This paper analyzes some of the geologic factors that would affect development of thick or closely-spaced seams using these mining methods. Occurrence of thick and closely-spaced seams Since mining conditions and methods differ around the world, a thick seam is often defined as a seam whose total thickness cannot be extracted using the available equipment. In the western US, the maximum extractable mining height is about 4.3 m (14 ft). For this research, a thick seam was defined as a minable seam 4.6 m (15 ft) thick or more. Since one of the seams is usually lost using standard mining methods, closely-spaced or split seams were also addressed. These were defined as two minable seams 1.5 m (5 ft) thick or more separated by 9 m (30 ft) of interburden. Thick or closely-spaced coal seams are common in the West. Their importance has not been documented due, in part, to the methods used to measure resources. In the past, all reserves greater than 1.1 m (42 in.) thick for bituminous seams and greater than 3 m (10 ft) thick for subbituminous seams were grouped together and were differentiated only by rank. Further differentiation by seam thickness or minability was not done. For this reason, reserve figures for thick or split seams are difficult to determine. By analyzing available published resource data, Ferm and Muthig (1982) addressed thick seam resources. They estimated a resource of 90 Gt (99 billion st) of coal (16% of the Western resource base) in seams 4.6 (15 ft) or greater at less than 610 m (2000 ft) overburden. Yet, a later study of Pierce and others (1982) on one thick seam deposit in the Powder River Basin estimated a resource of 103 Gt (113 billion st). Pierce (1986) reported that the overburden reached a maximum of 731 m (2400 ft). The resources in this single deposit exceeded the 90 Gt (99 billion st) total projected for the entire western US by 12.7 Gt (14 billion st). Due to such differences, this author chose to look at reported occurrences of thick or closely-spaced minable seams in place of resource figures, to verify the need to research thick seam mining in the West. An occurrence was defined as an isolated site where a thick seam or two or more closely-spaced seams were reported. The occurrences were derived from published material - mostly mine descriptions, measured sections, coal exploration logs, and oil and gas logs. Due to time constraints, the reserves associated with each occurrence were not determined. All data points were random. The analysis was limited to occurrences in Colorado, Wyoming, and Utah. Although source material available to the author was limited to general coal summa-

Jan 3, 1988

By S. K. Kawatra, T. C. Rao, J. P. Barnwal, Durga D. Patil

Coal macerals differ widely in their surface properties and in their hydrophobicities. Therefore, it is necessary to study the flotation time dependence of coal macerals using varying concentrations of various frothers and collectors. In the present study, froth flotation is used to explore the possibility of segregating coal macerals based on their relative rates of flotation. Petrographic analysis of the various macerals in the concentrate were carried out, and the results are expressed in terms of the recoveries of various maceral groups and mineral matter. Results show that it is possible to recover a good volume of the reactive macerals without mach loss of calorific value.

Jan 1, 2000

By Gu Guohua, Hu Yuehua, Zhang Qin

The flotation behavior of pyrrhotite was investigated by using ethyl xanthate as a collector. Results showed that pyrrhotite had good floatability from pH 2 to pH 11, and poor floatability when pH was >12. The flotation of pyrrhotite was dependent on pulp potential on various pH values. The potential-pH range for pyrrhotite flotation was established. Cyclic voltammeny and FTIR spectroscopic analysis showed that the major adsorption product of ethyl xanthate on pyrrhotite was dixanthogen. The intensity of FTIR signals of dixanthogen adsorption on pyrrhotite and the anode current of a pyrrhotite electrode and flotation response of pyrrhotite are correlated with pulp potentials.

Jan 1, 2005

By Theodore M. Gurr, James J. Bartels

Phosphate produced fertilizers provide the phosphorous nutrients required by plant life to sustain significant growth, thus improving the production of food for the world's population. Phosphorous replenishment of soil currently can be obtained efficiently by no other means than by direct application of phosphate fertilizer to the soil. Phosphate products are also utilized in animal feeds, detergent, and various industrial processes. Thirty-three countries are presently mining phosphate rock for the production of fertilizers, and its process byproducts. The major phosphate rock producers are the United States, the former Soviet Union, Morocco, and China [(Table 1)]. Phosphate rock is generally defined as a rock material that contains phosphate minerals which are sufficient for commercial usage. Phosphate minerals are found in sedimentary igneous and metamorphic rocks. Economic resources of phosphates are primarily developed from sedimentary rock sources. The apatite mineral family comprises the majority of phosphate constituents from both sedimentary and igneous rocks. Igneous phosphate rocks are generally composed of fluroapatite whereas sedimentary rocks are generally composed of carbonate fluroapatite, or chlorapatite. Phosphate rock is mined by a multitude of processes, including surface and underground mining. The mined rock requires mechanical and chemical processing to liberate the phosphate for utilization as fertilizer. Approximately 85% of the world's phosphate production uses sulfuric acid, with the remaining processes utilizing nitric and phosphoric acids. Ammonia is also introduced in the manufacture of liquid fertilizer, ammonium phosphate and ammonium polyphosphate. GEOLOGY Mineralogy and Chemical Properties Phosphate most commonly is derived from the mineral apatite, which is chemically described as CA5(F,Cl,OH)(PO4)3. Apatite is also broken up into the composite apatite minerals which are fluroapatite Ca5F(PO4)3, chlorapatite Ca5Cl (PO4)3 and hydroxyl-apatite Ca5(OH)(PO4)3. Carbonate CO3 can substitute for PO, forming carbonate apatite, called francolite. The guano phosphate (bird excrement) mineralogy commonly occurs as brushite CaHP04.2H20, monetite CaHPO4, whitlockite Ca3(PO4), and dahlite Ca10(PO4)6(OH)2. Apatite minerals form from igneous sources where they are developed deep in the earth's crust; and the cooling processes are slow, producing long, hexagonal prismatic to tabular crystals. The termination of the crystal can be basal plans or pyramids. In some instances, the crystals are bipyramids. Faster cooling, or sedimentary derived apatites are more commonly cryptocrystalline. Collophane is a name given to cryptocrystalline apatite found in phosphate rock in fossil form. Apatite minerals are relatively soft and are used to describe the 5 hardness on the Mohs scale. Cleavage is poor and develops along the C(0001). The color of apatite minerals varies from colorless, to violet, and blue, but are predominantly green or brown; luster is vitreous to subresinous. Collophane's physical appearance is often opaline, dense, with colloform structure and sometimes concretionary, nodular or pulverulent. Phosphate Bearing Materials Origins Phosphate deposits of igneous and metamorphic origins have been well defined. Sedimentary origins have been defined, but with a greater degree of uncertainty. Research in the 1980s proved out some of these processes through studies of real time deposition in Chile, Peru, and Australia. Igneous intrusive alkali rock and associated contact metamorphic rocks, provide approximately 20% of the world's phosphate. Fluorine containing apatite minerals are the most common materials containing phosphorous. Fluorapatite occurs in most igneous rocks. Fluorapatite and fluorine hydroxylapatite, together with carbonate varieties of these, are important members of the group. Where an essentially pure chlorapatite, carbonate apatite, and hydroxylapatite are rare and restricted in occurrence, the fluorine containing types occur in most all igneous rocks as early formed accessory mineral, usually in microscopic crystals, and may occur as extremely large bodies as magmatic segregations from alkalic igneous rocks. Apatite is also found crystallized in pegmatitic faces of both acidic and basic types of igneous rocks. More specifically, apatite is associated with magnetite deposits, in hydrothermal veins, especially those formed at relatively high temperatures, and in veins of the Alpine type. Apatite is common in both regionally and contact metamorphosed rocks, especially in the crystalline limestones where it is associated with sphene, zircon, pyroxine amphibole, spinel vesuvianite, phlogopite, talc, chloride schists, and as a contact metamorphic mineral.

Jan 1, 1994

By Ronald R. Bauer

Wollastonite is a little known industrial mineral of the silicate group. The largest and purest known deposit in the free world is being mined and beneficiated in Millsboro, New York by NYCO, A Division of Processed Minerals Incorporated. The associated garnet and diopside are separated from the wollastonite using dry high intensity magnetic separators. Beneficiated wollastonite is used extensively as an additive and filler in the ceramic, paint, refractory, and wallboard industries. Wollastonite acts as a functional filler due to its unique chemistry and physical acicularity.

Jan 1, 1982

By Ken Bright

This paper is an overview of approaches to assessment of ore grade for gold and the platinum group at the exploration stage of a project. Proper sampling techhniques must be complemented by good assaying. In turn, correct assaying has its roots in thoughtful, systematic sampling and sample preparation procedures. While intricacies of the subject matter could occupy a book, we will comment on acceptable sampling approaches, outline a lab hand- ling scheme, and discuss preferred analytical methods. Pitfalls previously encountered by the mining and exploration industry will be highlighted with emphasis on a perceptive under- standing of the nature of ore occurrence. Lastly, focus will be centered on reliable assay approaches.

Jan 1, 1988

By Tan Zhenxiang

INTRODUCTION Koolyanobbing is an open cut iron ore mine, which is located in Yilgarn region of Western Australia. To prevent the operators from suffering silicosis diseases and protect the air from being polluted, a series of dust control measures have been taken. These measures include ventilation and dust control system for sample preparation shed, dust collecting system for drill rig, dust suppression system for ore processing plant, dust control for haul road. The details related to individual dust control measure are dealt as follows. SAMPLE PREPARATION SHED DUST CONTROL The sample preparation is one of the major dust sources at Koolyanobbing. The activity is being carried out at the sample preparation shed. It typically needs to go through the following stages, that is, crushing, splitting, drying and pulverising. The amount of dust generated from crushing and splitting is mainly determined by the moisture content contained in the pre- pared sample. A significant amount of dust is generated at the sample pulverising stage due to cleaning sample bowl with com- pressed air. To protect the sample preparing personnel's health and make the dust level in the air meet the requirement from the health and safety authority, a central ventilation and dust control system has been installed at the sample preparation shed. As shown in Fig. l, the system consists of suction heads, suction lines, dust collector and vacuum fan. The fan creates vacuum environment in the system, therefore the dust is drawn into the dust collector through the suction heads and suction lines. The dust collector is of fabric filter. When the dusty air comes to the filter, the dust in the air is collected and retained on the surface of the filter while the clean air passes through and enters the atmosphere. The retained dust is blowed out by the pressured air pulses and deposits into the dust bin underneath the filter. A time relay device is used to control the cleaning time and the cleaning interval. DRILL RIG DUST CONTROL A hydraulic percussion drill is used to drill blast holes. To carry out the drilling operation properly and efficiently, the cut- tings are being flushed out of the hole by the compressed air. In order to prevent from the fine particles in the cuttings escaping to the air, a dust collector is attached to the drill. The collector mainly consists of suction head, cyclone and bag filter. Refer to Fig. 2. The suction head is installed at the lower end of the feed beams and is movable. The moving range is up to 250 mm. It is not only used to restrict the cuttings, but also used to prevent water from entering the filters when drilling wet hole. A 406 mm diameter primary cyclone is used to separate the heaviest particles in the cuttings. It is also used as blast holes sampling equipment. One part of the dust particles are collected by a sample bag through a splitter attached to the end of the cy- clone. The rest of the particles fall down to the ground through the closing rubber. The bag filter is driven by a hydraulic motor (1). It is used to collect the lighter particles in the cuttings. The filtering area is 16 m2 and the dust separation efficiency is up to 99.9%. The working principle of the filter is demonstrated in Fig. 3. When the rock drill (9) flushing is turned on, the pressurised air from the compressor is directed to the rock drill and to the pres- sure switch (10). The pressured air will open the pressure switch to de-energise and close the solenoid valve (4) The pressure affecting the cut-off cylinder (5) keeps the exhaust port flap open. When the flushing valve (8) is closed, the pressure affecting the cut-off cylinder disappears and the internal intake opening flap is closed by a spring. The pressure also ceases to affect the pressure switch and the spring switches the contact to the point 2. The time relay (11) is now activated and gives a 0.5 second current impulse to the solenoid valve and keeps the current cut off for approx 8 seconds. When the solenoid valve is live, it opens and lets an impulse of pressured air to the filters (2). These impulses will clean the filters.

Jan 1, 1997

By Carrie Smith

The 2025 Women in Mining USA National Conference, held April 15-18 at the Grand Hyatt Riverwalk in San Antonio, TX, brought together hundreds of professionals for a fourday event focused on empowering women and creating space for all individuals in the industry. Under the theme “Empowering the Future of Mining,” the conference served as a dynamic platform for professional development, knowledge-sharing and cross-sector collaboration. Organized by Women in Mining USA (WIM USA), whose mission is to foster equity, sustainability and leadership in mining, the event featured an extensive agenda including workshops, keynote speeches, panel discussions and networking opportunities. Attendees ranged from industry veterans to emerging professionals and students, united by a shared commitment to progress within one of the world’s most essential and traditionally maledominated sectors.

Jun 1, 2025

By C. O. Brawner

A recent advance in slope dewatering-depressurization and stabilization is the use of vacuum assist horizontal drainage. (Brawner and Pakalnis) Horizontal drains have been used for several decades to reduce water pressures in slopes to improve stability. The benefit from vacuum assist arises from an increased hydraulic gradient caused by an induced negative atmospheric pressure. A research program included a laboratory model whereby the effects of vacuum drainage were evaluated. Three case studies are described where the technique has been successful. The first is in a rock slope where flows increased from 0.1 1/min. under gravity drainage up to 1.2 1/min, upon vacuum. The second study involves installation of 17 drains placed at a slightly downward gradient to intercept and de- pressurize aquifers under a major tar sand deposit in Canada. The third study was on a large open pit copper mine in British Columbia where flow increased about 30 per cent.

Jan 1, 1984

By F. Bourgeois, J. A. Herbst, R. P. King

The ultrafast load cell (UFLC) has proved to be an exceptionally good device for the study of the fundamental processes associated with the impact fracture of particulate material. A new high- sensitivity UFLC has been commissioned at the Utah Comminution Center for the study of low-impact energy single-particle fracture. The force-time histories of individual fracture events have been measured. The force and energy absorbed at crack initiation have been measured at several particle sizes. The mass specific energy for fracture and the associated breakage function have been determined. The distributions of particle breakage energy and particle strength have been measured as a function of particle size.

Jan 1, 1992

By Shoung Ouyang, Pinnaduwa H. S. W. Kulatilake

Available literature on the topic is reviewed. Methods are suggested to improve the presently available techniques to perform probabilistic modeling of shear strength parameters for rock discontinuities. The Mohr-Coulomb model and a power law model are used as strength criteria to model shear strength of rock discontinuities. Use of various regression techniques for point estimation of shear strength parameters from direct shear data are discussed. Goodness-of-fit tests for bivariate beta and bivariate normal distributions are developed, and the applicability of them to represent the distribution of shear strength parameters is tested through examples. Both distributions seem to have potential to represent the statistical distribution of strength parameters.

Jan 1, 1986

By Omar Abd el Fattah Ramly, Abdallah Mohamed Sourour

FOREWORD In 1974, the Ministry of Housing and Reconstruction (The Client) which subsequently became the Ministry of Development and New Communities of the Government of the Arab Republic of Egypt assigned responsibility to the Arab Contractors (Osman Ahmed Osman and Company) for the design and construction of the tunnels under the Suez Canal. For this project the Arab Contractors of Cairo and Tarmac International of London formed a joint Venture, called Osmac. Sir William Halcrow and Partners of London are responsible for the design of the Ahmed Hamdi Tunnel as a Sub-Contractor to the Contractor. The advisory consultant of the client is a joint Venture between Tippetts-Abbett-McCarthy-Stratton (TAMS) of New York and Arab Consulting Engineers (ACE) of Cairo. INTRODUCTION A site investigation was carried out between Km 141 and Km 150 Suez Canal chainage to determine the ground conditions relevant to design and construction of a road tunnel under the Suez Canal. A feasibility study included aerial surveying, geological mapping and the drilling of 8 boreholes. Detailed investigation included the drilling of 105 boreholes, sampling, piezometer installation, pumping tests, and the digging of trial pits and trial excavations. In-situ work comprised SPT, permeability tests and dilatometer tests. Laboratory testing included soil classification tests, compaction tests, California Bearing Ratio tests, shear strength determination and oedometer consolidation tests as well as chemical analysis of both soil and ground water. The investigation revealed that the ground conditions at the first proposed El Shatt site (Km 148.5) were not favourable for bored tunnelling, whereas they were more favourable at the southern El Shatt site (Km 150.0).

Jan 1, 1979

By David G. Hammond

INTRODUCTION Previous papers and discussions at this conference have already covered the subjects of identification and nature of risks, allocation of risks and contractual arrangements. In this portion of the conference, in the light of topics already covered, we will consider how to minimize risks and how to mitigate losses. Webster defines mitigate as "to make less severe or painful", an apt definition for our purpose! RISK MANAGEMENT POLICY The first thing that must be said about risks, especially in construction, is that they exist and that they don't necessarily fall alike on the just and the unjust. Some risks, i.e., some kinds of risks, must be recognized as inevitable in engineering and construction and therefore must philosophically and realistically be accepted as part of situations to be dealt with. Dealing with means minimizing, covering, and sharing of risks and doesn't mean merely passing off the risks to someone else. While some risks can be avoided, for example, whether the structure will fall down or the excavation will cave in, risks management primarily deals with: A. minimizing risks---whomever risk it may be B. equitable sharing of those risks among the participants.

Jan 1, 1979

By D. Naden

Sulphuric acid leaching is the most common method of recovering uranium from its ores and in the following discussion various alternative low cost routes are investigated for recovering uranium from milled ore acid leach liquors. Historically uranium has been recovered from dilute impure leach liquors by packed bed ion exchange (IX), solvent extraction (SX) or a combination of both. All three process routes as commonly practised require complete separation of leached solids and liquids, as well as extensive solids washing in order to reduce soluble uranium losses to a minimum. Separation and washing are costly and often require equipment covering large areas of land. The size and capital cost of the post leach solids washing operation is controlled by the ease of washing the slimes fraction of the ore and the key to the problem of cost reduction, as many others have realised, lies in the ability to separate the slimes fraction of the ore from the more easily washed sands, to wash the sands in low cost equipment and to recover uranium from the slimes stream. Sands and slimes are usually defined in this context as the material larger than, and smaller than, 325 mesh (44 microns). The proposed flowsheets which minimise solid-liquid separation and washing have usually incorporated ion exchange (Refs 1,2,3), and resin in pulp is in fact practised in several mills in the USA (Ref 1). The resins used in these flowsheets and [cranium] recovery throughout the world have been strong base resins which load rapidly and are moderately selective for the uranyl sulphate complex anion over the range of pH which is conveniently achieved in an acid leach operation. Strong base resins are, however, not as selective as weak base resins and weak base liquid reagents owing to the adsorption of competing anions, some of which find their way into the product while others act as resins poisons. Ion exchange using strong base resins must therefore be followed by a more selective weak base SX purification step if pure yellow cake is required.

Jan 1, 1976

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007

By John C. Wangaard

A method of raising by use of a cage has been used with considerable success at the Cary Mine, Hurley, Wisconsin, on the Gogebic Range. The Cary Mine is owned by the Odanah Iron Company, Pickands, Mather and Company, Managers. This method is known to have been used previously at Tennessee Copper and probably in other districts. The Cary Mine was engaged in deepening the main shaft from the 34th to the 37th level. To accomplish this, and to facilitate development, a ventilation shaft 930 feet north of the main shaft was sunk from the 34th to the 37th level and crosscuts were driven on the 35th, 36th and 37th levels to the main shaft location, These levels are at 200 foot verticalintervals. All of this work was done in granite and the majority of the workings were not timbered. The next step was to get a raise through from the 37th to the 36th level, and from the 36th to the 35th level, which would later be stripped to full shaft size. Several methods of raising were considered including double-compartment cribbed and two single raises interconnected at regular intervals, but the cage method was chosen as it appeared to be a safe and efficient operation. The method in general consists in the use of a drill hole between levels through which to pass a hoisting rope to raise and lower a light cage.

Jan 1, 1958

23.1-SOURCE, POWER-SYSTEM ELEMENTS A. J. T HUM Basic considerations in providing power for mine production and collateral operations are: 1. Mining operations of any size normally use electric motors for driving all equipment except mobile service units. 2. The electricity for power may be purchased or self-generated, depending on the location, size and specific operating circumstances of the individual property. 3. The major elements of the power system will be the source, either an incoming transmission line from a utility in the case of purchased power or the power plant if self-generated. Energy for the power plant may be water, hydrocarbon fuels, waste heat or nuclear, which will govern the type of prime mover selected. 4. The electricity normally is generated in the form of alternating current and must be distributed to the points of usage. This usually requires a primary substation for transformation to suitable voltages and secondary substations at points of usage throughout the operations, The power is delivered from the primary to the secondary substations over transmission lines or cables, depending on distances, voltages and local conditions. 5. At the points of use, there will be starting and protective devices for each motor. In some instances, direct current will be needed and rectifiers of various types can be used to provide it. 6. The entire electrical system requires suitable switching and protective devices to prevent damage to the equipment in case of power failues or faults; also, in most cases, sufficient metering to establish the demand and amount of electrical energy consumed. 23.2-PURCHASED POWER A. J. THULI 1. Where public-utility or government-generated power is available, it usually is advantageous for the mine owner to purchase rather than generate. Purchased power generally will be cheaper and more reliable than operating a small generating plant except in some cases where waste heat is available as the source of energy and can be used to supply all or a portion of the power requirements. 2. If it is decided to purchase power, the owner usually must participate in the cost of constructing the connecting line from the closest existing utility line to his point of usage. If the connected load is less than 1,000 lip, it probably is best to let the utility provide the primary substation. For larger connected loads the owner can obtain a more favorable "primary voltage" rate if he provides the primary substation to receive the incoming power and transform it to the distributing and usage voltages. 3. The cost of purchased power usually is made up of a demand charge, deter¬mined by the maximum amount of power the customer takes during any 15-min period throughout a month, and a graduated energy charge for the kilowatt-hours consumed-that is, so much for the first block of energy based on the demand,

Jan 1, 1973