Search Documents

By Richard L. Bullock

INTRODUCTION TO COAL MINE PRACTICES To illustrate the trends and the proportions of the various methods used to mine coal underground, Fig. 1 is useful. However, of all the underground coal mining practices in the US, room-and-pillar mining still accounts for 96.5%. This percentage is divided as follows: conventional, machine cut-33.0%; conventional, hand cut -1.7% : and continuous mining-61 .8%. As was stated in Sec. 1, Chap. 7, the term "development" means different things to a coal miner and a metal miner. Though some of the ideas and concepts presented in the first two chapters of this section are valid for all types of mines, they apply particularly to mines using noncoal methods. In coal mines (and many other mines using coal mining systems) development refers to that phase of the mining cycle which advances several entries through the virgin seam, forming pillars by cross- cutting between the parallel entries. Because in the past, coal seams (as well as seams of potash, trona, oil shales, gilsonite, salt, and some uranium) have been much more uniform in their thickness, continuity, and quality, and because they often cover large areas, it has been possible to develop the room-and-pillar mine completely from a preplanned, systematic approach with a minimum of surface drilling information. As the better coal seams of the midwest and east are being depleted (or eliminated because of high sulfur), seams of poor quality and continuity will have to be mined. Also, seams that are not nearly so well known at greater depth will have to be taken as well as some of the steeply pitching and folded seams of the west. The American coal miner is only now feeling the need to do a much more complete job of prospecting the geology of the coal seams than he has ever done before. This is the only way that the risk of unknown rock conditions can be minimized. In many ways, surprises in the rock or coal seams are much more of a disaster to the coal miner developing a room-and- pillar mine than to his metal mining counterpart. Be- cause of the multiple entries, the complex set of the Federal Coal Mine Health and Safety regulations, and the totally dedicated design of coal mining equipment, coal mining systems do not have the flexibility to easily overcome changes in the seams mined or the rocks around them. Thus, if a wide parting of rock shows up unexpectedly in the middle of a coal seam entry being milled away by a continuous miner, it will either have to slowly "chew" through it, convert to a conventional mining system, or stop that particular entry. Likewise, if suddenly the coal disappears completely and in its place are the remains of an old creek bed, the "want" or "wash out" as it's called will usually have to be mined right along with the coal, by the same methods and with the same soft rock equipment, or the entry will have to be abandoned. For reasons such as these, coal seams today should be drilled from the surface just as thoroughly as the ore bodies in metal mines. Having once determined a more precise location of where the coal seams are located and which are suitable for mining, the engineer must still take a systematic approach to planning the mine as completely as possible. The initial series of entries must be planned to be driven either from the side hill portal or from the bottom of the shaft or slope. In either case, they should usually intersect the area close to the midpoint of the mass to be mined.

Jan 1, 1982

By Jr. McCulloch

Mining operations of Freeport Indonesia (FI) are located approximately 4 degrees -6' south latitude, 137 -7' east longitude in Irian Jaya the eastern most state of Indonesia (Figure I). The mines are located approximately 96 km (60 miles) from coast in the Carstenz Mountain range. The ore bodies are between 2900 and 4000 meters (9500 and 13 000 ft) elevation.

Jan 1, 1989

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-substitution with clays and organically bound. Rare earth minerals (REMs) such as monazite exist in coal and have a grain size less than 5 microns. Froth flotation was successful in concentrating REMs existing in a thickener underflow material derived from Fire Clay seam coal which contained around 300 ppm of rare earth elements (REEs). Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2300 ppm REEs. Using a laboratory flotation column, a concentrate containing around 4700 ppm of total REEs was produced equating to an enrichment ratio of 10:1. INTRODUCTION Rare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets, and batteries [1, 2]. REE recovery from alternative sources such as coal and coal by-products has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials. The average REE content of the world coal is around 60-70 ppm [2]. There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia (300-1000 ppm), the Fire Clay coal seam in eastern Kentucky (500 ppm), and the Sydney Basin in Nova Scotia, Canada (72-483 ppm) [3-6]. The occurrence of REEs in coal and coal by-products can be classified into three types, i.e., rare earth minerals such as monazite and xenotime, ion exchangeable REEs in clays, and REEs associated with organic matrix. The particle size of the rare earth (RE) minerals in coal and coal by-products is very small and normally in the micron and/or nanometer scales. The flotation technique, which is based on the surface chemistry difference, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime, and bastnaesite [7-11]. As such, flotation is a promising method for the concentration of REEs from coal and coal by-products. In the current study, rare earth flotation was conducted using the fine coal refuse generated at an operating coal preparation plant treating coal from the Fire Clay seam. REE concentration by flotation required an appropriate amount of grinding and control of the pH value while using typical collectors. Prior to RE concentration, release tests were conducted to evaluate the floatability of the recoverable coal and the REE distribution in the flotation fractions in the fine refuse. Mineralogy of the REE was studied using SEM-EDX."

Jan 1, 2017

By T. F. Torries

The primary merit criteria used by the mining industry is internal rate of return (IRR) rather than net present value (NPV) although NPV is favored by academicians. This paper discusses the problems with IRR and NPV and compares the multi-goal nature of decision makers and their need for information with the characteristics of NPV and IRR. Conclusions are that both NPV and IRR are needed for investment ranking, that NPV suffers the same multiple root problem as does IR.R, and the determination of incremental IRR to reach NPV consistent project ranking is misguided in practice.

Jan 1, 1997

The knowledge of aggregate size under various chemical and hydrodynamic conditions is very important for selective agglomeration, flotation and water clarification processes. Traditionally, aggregate size measurements are conducted using an ex-situ technique or in a diluted suspension. In either case, the measurement occurs in an environment that does not resemble the actual conditions under which the aggregates are formed. In this study, an on-line scanning laser microscope has been used to study the coagula size of micronized coal suspensions as a function of pH, solids concentration and agitation intensity. A maximum aggregate size of 310 µ m was obtained under relatively quiescent conditions and at pH values near the iso-electric point (iep) of the coal. The aggregate size results compare well with the coagulation efficiency measurements obtained under the same pH conditions.

Jan 1, 1994

By M. D. Bath

Minproc Engineers Inc. (Minproc) recently completed the construction and start-up of a process facility to treat 14,000 t/d of gold-silver ore at Kori Kollo, Bolivia. The comminution circuit consists of crushing and SAG-ball mill grinding. Breakage characteristics of the ore were determined and a circuit model developed. This enabled variations of the circuit to be simulated, and evaluated in terms of predicted performance to provide the criteria for final engineering design. Subsequently, analysis of the operating circuit provided data for circuit model-fitting. The validity of the original model and circuit performance predictions are discussed.

Jan 1, 1994

By J. J. Sammarco

Computer-aided control of a mining machine pl aces its operator in a safe, remote location, thus reducing health and safety risks, Sensing systems that provide machine position (xy coordinate) and heading (yaw), are extremely useful in aiding remote positioning of mining machines. The U. S. Bureau of Mines has developed two sensing systems for position and heading information: A scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system that employs ring-laser gyroscopes. This paper presents a brief background and status of these sensing systems as applied to the remote positioning tasks of a continuous mining machine. Included are field test results of each system operating in a room-and-pillar research section at a cooperating mine in West Virginia.

Jan 1, 1992

By L. Yuan, J. Soles, D. Bahrami, W. Tang, R. Thomas

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the NIOSH Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron, carbon steel), three types of liquids (diesel fuel, hydraulic fluid, engine oil), four air ventilation speeds (0, 0.5, 1.5, 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperature. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Mar 2, 2022

By James N. L. Lukanuski

Three porphyry copper districts in southern Arizona are partly overlain by post-ore fanglomerates which share certain physical and petrologic characteris¬tics and which may comprise a distinct and significant class of rock. These units are the Locomotive fanglomerate of Ajo, the Helmet fanglomerate of Twin Buttes-Mission-Pima, and the Cloudburst formation of San Manuel-Kalamazoo, termed "Locomotive-type fanglomerates" herein. Post-ore units at Poston Butte and Lakeshore, Arizona, and Sar Chesmeh, Iran, also appear to fit this class. "Locomotive-type fanglomerates" are composed of poorly sorted conglomerates, lenticular sandstone beds, andesitic to rhyolitic flows and tuffs, and unique monothologic landslide breccias. They contain fragments of holyokeite - - a rare oligoclase lava of porcellaneous appearance. Their basal contacts are considered to be depositional and overlapping, sometimes complicated by later low-angle faulting. They arc quite different than the younger Cila, Pantano, and most "Whitetail" alluvial beds, and the older Amole, Recreation, Claflin Ranch, etc. elastics; in particular they are thinner and less widespread. Their ages are Eocene to late Oligocene. "Locomotive-type fanglomerates" may be genetically related to porphyry coppers as products of subsequent differentiation and volcanism, and sedimentation in short-lived basins of restricted area and extreme relief. They might be utilized as reconnaissance guides to target areas and as structural guides within target areas in the southwestern U.S., Northern Mexico, and elsewhere.

Jan 1, 1975

By D. Kidd, T. Tucker, L. M. Indergard, S. Davis

"INTRODUCTION The Lisbon Valley Mining Co LLC (LVMC) operates the Lisbon Valley Mine located in SE Utah. The mine includes 3 open pits, 150-acre heap leach pad, and solvent extraction electro winning plant (SX/EW). Approximately 25MM tons of ore has been mined since 2005. The ore is stacked on the leach pad to an average height of 55 feet and occurs as a blend of crushed material (minus 2”) and run-of-mine (minus 24”). The host rocks include Dakota and Burro Canyon Sandstones. Copper occurs finely disseminated in this material at an average grade of 0.46%. Minerology is 63% sulfide, 27% oxide, and 10% insoluble. Total inventory mined through 2016 is approximately 230 MM lbs. METALLURGICAL CONSTRAINTS Copper production is constrained by areas of low permeability ore and geochemical issues, including acid consumption. The intrinsic permeability the ore ranges from 10-2 to 1 Darcy. This permeability does not permit sufficient aeration by natural convection, therefore oxygen transport is largely limited to the mass of oxygen that can remain dissolved in leachates. As a result, greater than 50MM lbs of copper remains in inventory and occurs secondary sulfides, including chalcocite, covellite, and bornite. BIOLEACHING FUNDAMENTALS Due to the higher activation energies of secondary sulfides, notably covellite and bornite, a strong oxidant is needed to remove an electron from the metal-sulfide lattice and release the copper cation into the sulfate solution. This process occurs most efficiently using the strong oxidant ferric iron (Fe3+). Ferrous iron can be oxidized to ferric iron by oxygen via chemical oxidation or biologically; which was measured to occur 500,000 times faster when using microbes versus oxygen.1 The microbes that oxidize ferrous iron (Fe2+) to ferric iron are naturally abundant and will develop biomass when appropriate conditions and nutrients present themselves. Most nutrients are provided by the ore/irrigation (P,N,Mg, Ca & Fe2+) while the others (O2 and CO2) are provided by air. In most cases, oxygen transfer is the rate limiting step during copper sulfide leaching. 1 Lacey & Lawson 1970 FORCED AERATION SYSTEM DESIGN This paper describes LVMC’s efforts to bioleach the remaining inventory by forced aeration. Two basic aeration systems were installed and tested including vertical wells and horizontal piping. Vertical System The vertical system was installed using the mine’s blast hole drilling rig. Wells were constructed using 4” high-density polyethylene (HDPE) connected to 4” polyvinyl chloride (PVC) screens similar to conventional bioventing wells. Ore samples were collected at each well location to characterize the spatial distribution of the remaining inventory along with fines (minus 200 sieve), pH (acid consumption), and iron. A block model of each analyte was developed and mapped in 3D."

Jan 1, 2017

By M. Misra

The processing strategy for the effective separation of bitumen from low grade (< 10 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1979

By W. S. Sadik

This paper presents the ventilation design for an underground testing facility in a salt medium. The underground workings consist of two-12 ft. (3.66 m) diameter watertight shafts and approximately 6000 ft. (1830 m) plus of drifting. These facilities are designed for the purpose of providing access for an in-situ testing of a salt horizon in which a variety of hazardous and non-hazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1988

By James R. Yancik

Economical and environmental pressures necessitates the recovery of the minus 0.6 mm x 0 coal generated by todays mining machines. This size fraction, dependent on the type of production unit, maintenance of the production unit, and the Hardgrove Grindability Index, can be a substantial portion of the Preparation Plant feed. Historically, dewatering of the collected 0.6 mm x 0 product has often been rather expensive and marginal with respect to surface moisture reduction. The Freeman United Crown II Preparation Plant more than adequately demonstrates that the continuous scroll type centrifuge can dewater 0.6 mm x 0 coal to acceptable surface moisture levels.

Jan 1, 1981

By QU Hong-lue, YANG Lin-han

Aiming at the subjective impact caused by subjective weighting method in the establishment of rockburst risk attribute identification and prediction model, the combined weighting method was introduced to eliminate the influence of unreasonable weight of each index. Eight discriminant indexes affecting the risk of rockburst were selected. Through the literature review, relevant rockburst cases were collected and 8 index rockburst sample sets were established. A variety of machine learning methods were used to analyze the feature importance of discriminant indexes in the samples, and then to determine the objective weight values of different methods. Combined with the subjective weights determined by the Analytic Hierarchy Process, the combination of weights were successively carried out. Based on the attribute recognition theory, the combination weights with different objective weight methods were established to identify the rockburst risk attributes, and verified by the confidence criterion. The results show that the objective weight value determined by the feature importance analysis of machine learning reduces the subjectivity of the weight of Analytic Hierarchy Process method, improves the prediction accuracy, and makes the prediction result closer to the fact.

Apr 26, 2022

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995

By J. W. Keck

Pilot plant grinding and concentration test results indicate that conglomerate native copper ore can be ground and concentrated using conventional techniques. Single stage autogenous grinding and rod mill-ball mill grinding required the same amount of energy far the required comminution. Metallurgical results were comparable for both types of grinding investigated.

Jan 1, 1973

By C. J. Webb

Abandoned uranium mines in the southern Black Hills of South Dakota were sampled for uranium, radium, and rare earth elements during 1992 and 1993. Analyses of water samples from several shallow ponds in the mine pits showed pH values between 3 and 4 with uranium concentrations between 1600 and 2600 ppb. Rare earth elements and their respective isotopes were analyzed with an inductively coupled plasma mass spectrometer and were referenced to a shale normalization pattern. All samples showed an enrichment in the middle rare earth elements. Rare earth levels often were greater than 0.2 ppm. At one site, the concentrations of lanthanides were 150,000 times above background levels. While the southern Black Hills have long been known for rich uranium ore deposits, these analyses show that significant levels of rare earth elements also are present, indicating that the potential exist for future development.

Jan 1, 1995

By F. S. Knoll

The high tension process which separates materials based on relative differences in surface conductivity has been very successful in recovering non-ferrous metals from municipal waste. Aluminum is by far the largest constitutent of the total non-ferrous metal fraction; accounting for >95% in most localities. Wire and insulation mixtures from industrial wastes have been treated commercially for several years by a high tension process initially developed for use in the iron ore industry. The wire and insulation application was a forerunner of municipal waste dry treatment technology. In the past eighteen months the rotating-drum-type electrostatic separator has undergone extensive testing and development in order that the process might be efficiently adapted to the recovery of aluminum from municipal waste.

Jan 1, 1974

Growing concerns of climate change and its potential association with the release of greenhouse gasses to the atmosphere have prompted possible legislation which would require minimization of greenhouse gas emissions. Carbon dioxide and methane, both of which largely contribute to the greenhouse effect, have direct links to the fossil energy industry sector. Specifically, the combustion of one ton of coal produces between one and three tons of carbon dioxide, dependent upon the carbon content and heating value of the combusted coal. Additionally, coal mine methane (CMM) released through a mine?s ventilation system has a radiative trapping impact approximately 20 times greater than that of an equivalent mass of carbon dioxide. The capture of coalbed methane (CBM) prior to the mining process and its utilization as an alternative energy source provides the possibility of a decreased carbon footprint. Domestically, the past 25 years have seen a significant expansion of the CBM industry. Internationally, in developing countries such as China, the need for western coal degasification technology is growing. A collaborative, international effort will be required to initiate a recognizable decrease in global greenhouse gas emissions. This paper identifies the potential decrease in equivalent carbon dioxide emissions through effective degasification at a hypothetical longwall mine located in China. Advanced, three-dimensional gas reservoir simulation software will be utilized to determine the maximum feasible CBM recovery in a low permeability, high gas content reservoir prior to the mining process.

Jan 1, 2010

By Mark Van Dyke, Ted Klemetti, Jake Beale, Zoheir Khademian, Joe Wickline

In 2016, a 3.7-ML magnitude event caused by mining activity occurred at a longwall mine in southwestern Virginia which was recorded by the United States Geological Survey (USGS) and felt by local residents. The event was the largest of its kind since a global mine design change by the operator was instituted in 2008 following three large events in 2005, 2006, and 2007 (3.4, 4.3, and 3.4 Moment Magnitude (Mw), respectively). Two of the three pre-2008 events (2005 and 2007) damaged ventilation controls in the mine which fueled a mine fire. In 2016, the mine’s management requested researchers from the National Institute for Occupational Safety and Health (NIOSH) to access geological data and determine what parameters could possibly lead to events of a magnitude of 1.0 ML or greater. Evaluation of 2152 geological data points and modeling revealed three major geological factors in common with the majority of the 181 recorded +1.0 ML events from 2009 through 2016. Three levels of seismic potential were identified as follows:

Aug 4, 2023