Search Documents

By S. M. S. Azghdi, K. Barani

The effect of microwave treatment on the surface roughness and wettability of chalcopyrite (CuFeS2 ) and on the chemical composition of its surface was studied. The microwave source was a conventional multimodal oven with frequency of 2.45 GHz and maximum power of 900 W. Pure chalcopyrite specimens and purified chalcopyrite concentrate were used in this study. Analysis using atomic force microscopy showed a decrease in the surface roughness of the chalcopyrite after microwave radiation. This decrease may be due to oxidation of the surface and formation of iron oxide. Moreover, the surface wettability of the chalcopyrite mineral increased with increasing duration of microwave radiation, which was in good agreement with the micro-flotation mass recovery results. The increased wettability of the surface may be attributed to the decreased surface roughness by microwave radiation. Analysis using scanning electron microscope/energy-dispersive X-ray spectroscopy indicate that after microwave radiation, the contents of sulfur and iron increased whereas that of copper decreased on the surface of the chalcopyrite, significantly changing the average atomic number of the chalcopyrite surface.

By James J. Snodgrass, David E. Siskind

The Bureau of Mines investigated the effects of vibrations from underground blasting in four rock types to define blast parameters that affect vibration amplitudes and to establish means of predicting expected vibration levels. Previous studies of surface blasting indicated that charge weight per delay period had a major influence on vibration amplitudes. Dividing the distance from the blast by the square root of the charge weight scaled the effect of various charge weights, however, and allowed vibration data for a particular site to be represented by a propagation equation of the form v = K(D/W ½ )-n (1) where v = particle velocity, D = distance from the blast, W = maximum charge weight per delay period, and K and n = empirically determined site constants. For square-root scaling, particle velocity and acceleration data from the underground sites appear to follow a similar propagation law. The subsurface data are in good agreement with those of the surface studies and provide a basis for engineering estimates of vibration amplitudes in many different rock types.

Jan 1, 1974

By A. T. Sapulek, C. S. Özveren, D. W. Dixon

The prediction of underground methane emission from longwall coal faces has been extensively researched for a number of years and numerous prediction methods have been devised. Many coal mines employ sophisticated environmental monitoring equipment which generates large amounts of data including, methane concentration, air velocity and barometric pressure. Presently this information is mainly used only to indicate alarm and danger levels of the monitored data for management purposes, however, the potential uses of this data are enormous[1]. This information could be used to good effect within a production/methane emission strategy as detailed in a previous paper[2]. The paper presents a practical application of artificial neural networks to underground methane prediction. Data on methane concentration and coal production has been obtained from an underground coal mine. The data is used in a neural network architecture and forecasts of methane concentration have been obtained. The forecasts are examined and there is a discussion of the potential use of the predictions from neural networks in the field of mining production control.

Jan 1, 1995

By W. A. Zingg

Impervious zones in copper waste heaps create a problem in contacting the rock with leaching solutions. These zones are normally associated with compacted layers .formed on the surface of each lift by dump truck traffic and by disintegration of the rock exposed to atmospheric conditions. These layers are usually only a few feet in depth--but, nevertheless, act as barriers to vertical flow causing the leach solution to perch in the heap, Consequently, much of the rock remains untouched and the leach solution breaks out the side of the heap instead of continuing downward to bedrock. One solution to this problem is breaking the hard pans with explosive charges. However, to use explosives means adopting new explosive materials and methods. To use this process successfully requires finding answers to operating conditions inherent to waste heaps. Foremost among these are: (1) type and size of casing that can be used because of limitations brought about by drilling problems, caving and, corrosive conditions; (2) perforating the casing at required levels; (3) an explosive capable of being pumped; (4) obtaining detonation of the, main charges through, the wail of the casing; (5) an explosive with the ability to propagate through the voids of the rubble and one which is not affected by water, acidic solutions, or back pressure conditions from hydrostatic heads; (6) to heave and rupture the compacted zones without chambering or recompressing the waste material.

Jan 1, 1970

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the U.S. for the detection of fire in the belt entry and monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data has the potential to provide fire characteristic information such as fire growth (heat release rate) and exact fire location. This information is critical in making decisions regarding fire-fighting strategies, underground personnel evacuation, and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide (CO), carbon dioxide (CO2), and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division (PMRD) Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy. INTRODUCTION Fires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases. The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke, and toxic gases are produced and transported by the ventilation system, and provides an indication of the time available for escape or firefighting [1]. The HRR is also an important input parameter to mine fire simulation models. Measuring the HRR of an actual fire can be a difficult task. Early experimental measurement of HRR focused on the heat output as represented by the temperature of the product gases. In ASTM E1321 (LIFT test), an array of thermocouples was positioned in a duct which captured all gaseous combustion products to measure their average temperature. This approach assumed the flow is adiabatic, which is never a reality. Significant progress on measuring HRR was made when Huggett showed that, for most common materials containing C, H, O, and N, the average heat release per unit mass of oxygen is 13.1 MJ/kg O2 [2]. Thus, the oxygen deficit is a measure of the HRR in the flow that the duct captures. This approach is termed oxygen consumption calorimetry (or the oxygen consumption method), and is widely used in the fire protection community."

Jan 1, 2017

By Daniel C. McLean

Chemistry plays a more important role in milling operations than is generally recognized, particularly in fluid- solid separation processes. Chemical aspects are also very important insofar as plant water quality is concerned, and in the manner in which this water quality effects plant design and operation. Aside from the inherent chemical characteristics of plant water, the mineral preparation industry is becoming increasingly more dependent on the use of mining chemical reagents--relatively new to the coal industry, but items of I standard usage in complex metal recovery plants. These chemicals have many useful properties and can produce significant improvements in operations and metallurgical efficiencies when used properly and intelligently. They can produce poor results and sometimes severe losses when used improperly. Most reagents are relatively expensive on a per pound basis, hence costs can be excessive if they are used wastefully or inefficiently.

Jan 1, 1968

In underground coal mining, one of the biggest challenges is spontaneous combustion, which will not only present safety hazards but result in reserve losses as a result of burnt coal. The released heat coupled with other combustible gases commonly encountered underground will significantly increase the risk of explosion. In this paper, three-phase foam as an environment-friendly fire fighting agent composed of nitrogen, water and fly ash is introduced. The nitrogen facilitates inertization of the fire zone; the water helps cool down the fire and the fly ash can closely cover the coal to isolate the oxygen. What's more, the fly ash and the foaming agent are good free radical absorption. The comprehensive merits mentioned above make three-phase foam quite effective in quenching spontaneous combustion. Experiments indicate that three-phase foam can significantly slow down the temperature rise of coal during oxidation. The comparison between slurry and three-phase foam shows that the latter one is capable of flowing upward in the porous media so as to extinguish the high-point fire and concealed fire.

Jan 1, 2011

By Zvonimir Jam?ek

In Rudarski Institut Ljubljana (RIL), i.e. Ljubljana Mining Institute, we have developed CADRIL, a smaller CAD package which purpose is to overcome the difficulties by introducing Computer Aided Design in our mines. Program CADRIL is a graphics shell for several computer applications in mining. With the basic version of CADRIL all 2D working maps for daily use can be produced. Inserting different program blocks into CADRIL we get versions MAPRIL, TAHRIL, SECRIL and so on. The main purpose of all versions is graphics design. The main and most innovative feature of CADRIL is the screen four-word command menu. Not having pull-down or tablet menus is the speciality of this program. CADRIL contains 500 achievable commands. Each of them can be composed by choosing two to four expressions stored and shown in a specific four- column menu, sorted as objects functions, parameters and modes. Thus all commands are immediately accessible. As a result of its plainness and adaptability to the present working methods of mining engineers, CADRIL quickly attained a good reputation in our mines.

Jan 1, 1992

By L. Andrews, G. Smits, M. D. Adams, E. A. Viljoen

A new approach has been developed that is capable of ascertaining the ore component that is responsible for the preg­robbing of pregnant pulps. Many gold mines are currently treating ores containing a component that is detrimental to the recovery of gold, in that they "preg-rob" the pregnant pulp by adsorption of some of the dissolved gold. The identity of the preg-robbing component in this type of ore has been the subject of considerable debate over a lengthy period, th various suggestions including amorphous carbon, chlonte, chalcopyrite and layered silicates, such as the phyllosilicate minerals pyrophyllite, kaolinite, phlogopite and illite. A means is now available to identify and characterize the preg-robber in gold ores. This new approach consists of contacting the ore with a synthetic aurocyanide solution, identifying the mineral grains by optical microscopy and analysing each grain individually using high-sensitivity electron microprobe analysis. The approach is exemplified in this initial study by identifying the preg-robbing component in an active sample of gold-bearing shale to be an amorphous carbonaceous phase consisting of discrete particles of about 5 µm diameter interspersed with shale particles and agglomerated into grains of up to 100 µm diameter. Microanalysis of these grains as well as other mineral particles revealed that the gold content of some of the carbonaceous grains was close to 7000 g,lt, with no gold being detected in any of the other mineral phases that were found to be present (e.g. quartz, chlorite, muscovite, pyrophyllite, etc). Bulk analysis of the sample for carbon and gold confirmed that gold loadings of around 7000 g,/t would be expected if all of the gold were adsorbed onto the carbonaceous component. The carbonaceous constituent is probably also responsible for the anomalously high surface area measured for the material. It probably acts in a similar fashion to activated carbon, and the correct choice of organic blinding agent will decrease the extent of preg-robbing by lowering the activity of the material for gold, without causing any downstream problems such as fouling of the activated carbon used for gold recovery

Jan 1, 1993

By Thomas H. Koenning, James R. Boulton

The coal mined by Cyprus at the Shoshone mine near Hanna, WY is highly susceptible to spontaneous combustion. Spontaneous heatings have occurred in the gob of several of the longwall panels and, in some cases, following roof falls. Prevention and detection methods have evolved over the years as more has been learned about the occurrences. Seal design and construction have progressed to reduce air leakage into the gob. Pressure balancing has been successful as a supplement to good workmanship in reducing leakage. Early heating detection has improved as knowledge has been gained. Prior methods of detection relied upon thermocouples detecting a temperature change. Later a gas chromatograph was used to analyze gob gas samples. Initially the products of combustion (POC) were relied upon for detection. Most recently, lack of oxygen depletion in the gob has been used as an early warning of problems. Examples are presented to illustrate the evolution of spontaneous combustion control at the Cyprus Shoshone coal mine. Methods have been developed which minimize the oxygen concentration in the gob and reduce the potential for spontaneous combustion.

Jan 1, 1997

The day after I reached New York, on January 30th, John Ryan of Anaconda told me where they wanted me to go. Late in 1916 the Russian Czar, desperate for money and supplies with which to carry on his unhappy share In the first World War, sent emissaries to the United States to see if our great mining companies might be interested in trying to find mines and to bring them to production in the millions of acres of the Imperial Estates in Russia and Siberia. It looked like a long chance as no one knew whether or where there might be important ore bodies. Even if they found them it might be a hopeless task to equip them under wartime conditions But the American copper companies had plenty of money and they were used to taking risks. They made a supersecret agreement with the Czar's deputies to send an exploring expedition to Russia at once I never learned the names of the other companies but Anaconda was to man- age the venture. Horace Winchell, then the leading mine geologist In the United States, was to be in charge of operations. Charles Janin, an eminent placer and dredge expert, was to study chances for producing gold and platinum. Though at 33 years of age I was much younger than the others, I was chosen to hunt for copper and other valuable metals. Charles Boynton, a business man who had lived in Russia and had married an attractive Russian woman, was to join the party and carry on any necessary financial or diplomatic affairs. He had gone on ahead to arrange for our reception Finally a graduate student from Ann Arbor named Steinberg was to go along as Interpreter. We soon found out that if his Russian was no better than his English his interpretlng couldn't be trusted too much I knew nothing about the millions of square miles In Russia and Siberia, and even less about what mineral deposits might be found, but I was delighted at the prospect. I was treading on air for the few

Jan 1, 1976

By J. A. Baicker

A 2 1/2 inch diameter probe containing a high resolution gamma ray spectrometer was developed for downhole ore grade assays to depths of 6,000 feet. Tests have been conducted on the characteristics of this tool for in-situ determinations of uranium by means of natural gamma ray counting, and of copper, silver, gold, iron and coal quality by means of neutron-induced gamma rays. Application of the technique for improved carbon-oxygen logging in oil fields is promising. The probe contains a cryogenically cooled high purity germanium detector and a 4,000 channel spectrum analyzer. Gamma ray spectra are digitally transmitted up the cable to the truck-mounted data processing system. We found that uranium can be assayed directly in different types of formations independently of the degree of geochemical disequilibrium by counting the relatively weak 1.001 MeV gamma ray of protactinium-234m. Neutron activation work shows that in-situ determinations of copper, silver, iron and coal quality are technically feasible. In carbon-oxygen oil well logging the technique allows an accurate determination of carbon, oxygen, hydrogen, chlorine, silicon, calcium and iron, and shows promise of providing an improved oil/water differentiator.

Jan 1, 1982

By M. G. Bakker, D. D. Murphy, D. R. Spears

The US Bureau of Mines studied the mechanism of shear flocculation of silica with stearic acid. At pH 6 and 12, shear flocculation of silica was not observed with the addition of up to 4.5 x 10-4 M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations = 10-4 M (22.5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labeled with a doxyl group. The presence of the spin-labeling group did not greatly affect the shear flocculation properties of stearic acid. Adsorption of labeled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicated that the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-5 M (22.5 lb/st). The results are discussed in terms of a possible mechanism for shear flocculation.

Jan 1, 1995

By G. V. Sullivan, B. E. Davis, T. O. Liewellyn

A technique was devised by the US Bureau of Mines to recover coarse [+1.2-mm (14- mesh)] North Carolina phosphate now discarded as waste. Concentration utilizes the difference in particle sphericity between the relatively flat calcite and the rounded phosphate pebbles. Sizing, treatment in a continuous hydraulic classification system, and grinding upgraded a 17% P,O5 reject to 4.5% P,05 with a phosphate recovery of 63%. The CaO: P2O5 ratio was reduced from 2.49 to 1.66.

Jan 1, 1987

By E. B. Kroeger

One of the problems encountered when constructing a roadway is the planned route often needs to cross soils that are soft and highly compressible. An approach to dealing with soft and compressible soils is to construct the fill from lightweight materials, thereby reducing the stresses on underlying soils. Most lightweight fills have approximately the same cost, so the most important consideration when choosing a lightweight fill is that the material properties of the lightweight fill match the conditions existing at the site. Expanded polystyrene (EPS) has been used as a lightweight fill material for more than 30 years. The EPS used for road fills is typically in the range of 0.5 to 2 lb/ft3, and has a compressive strength of in the range of 10 to 30 lb/in2. If a higher strength material is needed, then the material density is increased, which also adds to the cost of the material. Another type of lightweight fill material that is commonly being used is lightweight aggregate (LWA). LWA can be created by passing slate or shale through a rotary kiln or reheating coal fly ash with other materials to form pellets or aggregate. Several companies throughout the U.S market these materials under a variety of names. LWA can have a unit weight from 45-80 lb/ft3. For sites where trucking granular fill does not pose a problem, this material may be an alternative to EPS. One of the drawbacks to using LWA is the availability of the material. Only a few companies are manufacturing LWA, so it may not be available or may be cost prohibitive in certain areas of the country. Lightweight flyash blocks have been produced which may fill the gap in unit weight between the EPS and LWA. Blocks have been produced with a unit weight as low as 30 lb/ft3. They are relatively inexpensive, easy to handle, and have a moderate compressive strength. Although the unit weight is dramatically higher than EPS, the strength is also higher. If lateral stabilization of the fill is a problem, then geofabrics or grids can be incorporated into the design to add lateral strength.

Jan 1, 2003

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The STG integrated method of grouting can be divided into the several phases as outlined in preceding chapters. For convenience in describing technical procedures, they can be grouped as: 1. Investigations in non-geotechnical, exploration bore¬holes. 2. Drilling the holes necessary for geotechnical investiga¬tions and for grouting. 3. Conducting appropriate hydrogeologic tests in those holes and consequent calculations. 4. The preparation of a clay mortar. 5. The preparation of a clay-cement grout with additives. 6. The injection of the grout. 7. Checking the quality of the grout curtain. Items 2, 4, 5 and 6 are discussed below. These activities contain the procedural aspects of grouting. 7.1 DRILLING GROUT HOLES Grout holes belong to a very select class of drillholes. The necessary drilling equipment must enable the operator to drill the holes in inclined, twisting directions. In addi¬tion, the equipment must permit drilling under structurally and hydrogeologically complex conditions. The equipment must permit the operator to conduct specific testing activi¬ties in the drillholes. These activities include hydrodynamic analyses, flowmetric analysis, and the installation and re¬moval of deflectors, packers, grouting plugs, casings, lin¬ers, pumping facilities and other work. As explained in Chapters 5 and 6, the grouting of sat¬urated rock is conducted both through holes drilled from the surface and through holes drilled from the face of a shaft, drift, or tunnel. The drilling of grout holes from the surface can be carried out by an aggregate of equipment that can be the same equipment used for drilling exploration boreholes. Depending on the projected depth of the holes, the STG ZIF- 1200MR and ZIF-650 drilling rigs (or modifications of them) are used. The SKB-4, SKB-5 and SKB-7 high-output drilling rigs (workover rigs) have been used in recent years. The STG BMP-24 drilling rigs are used for carrying out the descent-lifting operations for drilling holes from the sur¬face. In a number of cases, the UKB-500C, URB-3AM and URB-2A power-fed drilling equipment is used for drilling holes from the surface. It should be noted that the drilling of grout holes usually requires an electric drive assembly. Drilling with diesel drive assemblies would be used only to preclude the possi¬bility of losing electric power during drilling operations. Turbine drilling would be used only for appropriate techni¬cal-economic reasons. The selection of the grout hole design is determined by the hydrogeological and structural geological conditions at the site as interpreted in Chapters 2 and 3. The design of grout holes must be as simple as possible in order to min¬imize costs. Hole design guidelines can be adopted as a basis for this purpose, unless site-specific conditions require otherwise. The mouth of the drillhole must be outfitted with a guide-pipe having a length of at least 2 m and an outside diameter from 219 to 234 mm. The upper part of the hole must be attached by a jig consisting of borehole casing that has a diameter ranging from 108 to 146 mm. The length of the jig h is determined by the equation [ ] where k = 1.1 to 1.2 is the load factor; P,, is the injection pressure of the grout into the mouth of the drillhole; D is the external diameter of the jig pipe; m = 0.6 to 0.7 is the work condition factor; T[ ].1 MPa is the bonding value of the rock cemented to the jig. The grout hole is drilled from the jig shoe to the de¬signed depth using a rock-crushing bit with a diameter of 93 mm or more. However in complex hydrogeological condi¬tions when the shaft intersects unstable rock, other hole designs can be used. The diameter of grout holes must permit an aggregate of investigations to be conducted in them using down-hole borehole geophysical and flowmetric logging instruments. It is necessary to cement the casing strings reliably in the grout holes, thereby permitting the injection of the grout under high pressure through the pres¬sure tight mouth of the borehole. Technological details for drilling grout holes such as the rotational rate of the drill bit, the axial load on the rock¬crushing bit, and the drilling fluid flow rate are optimized for the specific rock-hydrogeological conditions largely by experience. The hole diameter and type of rock crushing bit are important variables in these details of drilling. It is advisable to drill holes using water as the drilling fluid. However in those cases where the hole walls are unstable or under very high ground water pressure, the use of a well¬ engineered drilling mud should not be precluded. Unfortu¬nately, drilling mud can influence test results. When steeply dipping fractures with inclination angles of more than 60 to 70° are encountered, it is necessary to drill guided, inclined grout holes. This procedure permits the maximum number of fractures in each hole to be stu-

Jan 1, 1993

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium, and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. [Table 1] affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak- type brines, produced mainly for lithium. MARKET ATTRIBUTES Some of the important market traits common to industrial minerals used by the chemical industry are: 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities. 8. Purchases are generally by contract of one year or longer term, with spot buying playing only a minor role. 9. Contract prices are usually fixed in short term commitments, but may vary according to assay, with premiums and penalties for content above or below the norm; however, general practice is for specifications to be fixed in the contract with minimums being set for the desired material and maximums for undesired elements. In longer term contracts, prices are often escalated on labor, fuel, and other vendor processing costs. 10. Suppliers of individual commodities to the chemical industry tend to be limited in number and are generally medium- to large-size producers that supply a few major consumers. 11. The bulk of the mineral volume is for basic chemical uses, sulfur suppliers to sulfuric acid producers and fluorspar for hydrofluoric acid producers being typical examples. These basic chemical products then are used for the production of other products. 12. Shortage of a supply of adequate quality leads consumers to seek substitutes. In the case of fluorspar, much work is being done on recovery of fluorine from phosphate rock. Success in the form of fluorosilicic acid and/or hydrofluoric acid production could, in time, affect the hydrofluoric acid chemical industry. 13. Markets tend to be characterized by cycles of shortage followed by oversupply, with attendant wide price fluctuations. 14. Baniers to trade can have an adverse effect on the necessary movement of industrial minerals used by the chemical industry in international trade. Antidumping laws, quotas, and tariffs can disrupt or dislocate normal markets. 15. Chemical industry consumers may back-integrate for security of supply or for favorable economics, sometimes by joint ownership and often with experienced mining partners.

Jan 1, 1994

By J. C. Yingling, J. W. Leonard

Introduction The absence of coal-face particle management heavily penalizes the transportation of coal from initial loading to final consumption. The penalties include dust problems, significantly reduced mine-loading-cycle productivity, mine-belt spillage, excessively high coal-preparation costs, chute blockages and dangerous pulverizer blockages at the final point of utilization. Fine particles commonly cause environmental and economic problems. It is well known that these fines can cause safety and environmental dust problems. But it is not well understood that these fines can also swell broken coal to a point where 5% to 15% more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading-cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long-established, and frequently misleading, basis of tonnage. It is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain nonfrothing chemicals, which are added to mine-face spray water, and by employing improved mine-face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed. The precursor to the work presented in this paper, involving the bulk density improvement for broken coal and the subsequent production gains for underground coal mines, was earlier presented in Leonard and Newman (1989). In the past, this topic has been studied and practiced only in byproduct coking in the steel industry. However, a potential exists for an increase in coal-industry productivity by improving the bulk density of coal to yield a subsequent reduction in delivered cost. This can occur with breakage, handling and treatment methods resulting in the loading of greater quantities of coal in fixed volumetric capacity haulage units such as mine cars, shuttle cars and scoops. Laboratory-based experiments to achieve an increase in productivity by increasing coal bulk density were discussed in Leonard, Paradkar and Groppo (1992). Chemical techniques using small quantities of commercially available reagents (surfactants) resulted in about a 13% to 15 % increase in bulk density, which was thought to produce a proportional increase in the productivity of a mine, together with a subsequent reduction in cost. The idea is to mix the reagents with the water that is used to spray coal during mining. In this paper, the impact of bulk density improvements on production rates is presented. Increases in production ranging from 60% to 88% of the bulk density increases are projected. This analysis was performed for atypical continuous-miner section. In the following sections, discussion and results of the analysis are presented. Discussion An analysis was performed to ascertain the impact of bulk density improvements on face-production rates for a typical continuous-miner section. Figure 1 illustrates the section layout and cut sequence. This layout and sequence is identical to the case described in King and Suboleski (1991). As can be seen, the section uses five entries and 12.2-m cuts that are taken by a remotely controlled continuous miner. The seam height is 1.5 m and two shuttle cars (5.7 t nominal capacity) are employed for haulage from the miner to the section feeder, which, throughout the cut sequence, is positioned as illustrated in Fig. 1. The simulation model was coded in the SIMAN simulation language. The major impacts of increased bulk density improvements on such a production system are as follows: •Shuttle-car payloads, in terms of the mass of coal transported per haul cycle, are increased proportionally to the increase in bulk density that results from the application of surfactant. •Shuttle-car discharge times should remain largely unchanged, because they are determined by the volume of material that is discharged, rather than the mass, and this volume does not change.

Jan 1, 1996

By J. A. M. Cano

Introduction Since the beginning of operations at the pellet plant at Ponta Ubu ES, Samarco Mineração SA has produced pellets for direct reduction and blast furnace processes. Of the total amount of pellets produced from 1977 through 1993, 55 % are used in the blast furnace, about 45 Mt (49.6 million st). The principal components of pellet gangue are calcium oxide, magnesium oxide, silica and alumina. They should be added in adequate quantities to guarantee the mechanical resistance of the fired pellets under blast furnace conditions. Over the years, the pellets produced by Samarco had a silica content between 2.5% and 2.8% and varying binary basicity preferably between 0.8 and 0.85. On the other hand, the increasing amount of industrial waste in siderurgical plants caused by the increase of steel production has caused some countries to put into practice methods to reduce the volume of slag produced in the blast furnace. This paper's goal is to find an alternative for decreasing the amount of slag produced in the blast furnace. It is possible to decrease pellet gangue by decreasing the silica content to about 2%, leaving the metallurgical properties and quality of pellets unaltered. For this work, Samarco pellets were used with Si02 between 2.5% and 2.8%, pellets with high silica and pellets with Si02 between 2.0% and 2.3% low silica. Both were partially fluxed by the range of varying basicity CaO/SiO2 from 0.8 to 0.95 during production. Experimental tests on pilot scale Thhis work began in January 1986 in the pilot plant (pot grate, Fig. 1) at Samarco. Its goal was to obtain preliminary data that would indicate the bybility of the project. It also formed a solid base to extend the studies in tests on an industrial scale of production for blast-furnace pellets. The pot grate is a test furnace composed of a gas burner, a combustion chamber and a grate, connected by hot air ducts. The burner is fed by a mixture of LPG and air. It reaches high temperatures through oxygen injection. The combustion chamber heats the air that comes from the turbocompressor. This hot air flows through the ducts to the grate on which the pellet samples are fired. During updraft drying, downdraft drying, preheating, firing and afterfiring, the upward and downward direction of the air flow can be controlled by valves driven by pneumatic cylinders. The pot grate indurator was fully automated in August 1989. Positive and negative pressures measurements resulting from gas passing through the pellet layer, as well as temperature readings, are recorded in graphs in relation to time for all tests. The tests depend on the various steps carried out in sequence that can influence the results of the tests. Therefore, some criteria were adopted to restrict the number of variables in the process. This was done to facilitate the results of the analysis. The pellets were composed of concentrate, bentonite, hydrated calcitic lime and metallurgical coal, all regularly used in the pellet plant. The material balance of the pellets mix was determined from the chemical analysis of the components. Table 1 shows the chemical characteristics of the concentrate and the additives used in the pilot plant and industrial tests. The basicity has a marked influence on the metallurgical properties of the pellets produced by Samarco with a silica content between 2.5% and 2.8%. However, for pellets with low silica (about 2%), it was necessary to study the variation in the parameters of quality in a wide range of basicities to deliniate with precision a scope of work. A large variety of low-silica blast-furnace pellets were produced at the pilot plant with binary basicity varying between 0.8 and 0.95. After chemical analysis, those pellets were separated into five groups of different binary basicity (0.8, 0.84, 0.87, 0.90 and 0.95). Each was then split, one part for metallurgical tests in the laboratory at Samarco and another to be evaluated in a laboratory for metallurgical tests in Germany. It was agreed that the tests to evaluate the quality of the pellets in the two [ ]

Jan 1, 1996

By James A. Martin

Evaluation and subsequent development of a quarry in east-central Missouri was based on a general but brief examination of outcrops and core from five (5) test holes. Neither core, outcrops, nor existing quarries in the general area gave any indication of potential major problems. In the third year of operation large areas of collapse rubble, consisting of green shale and large blocks of limestone and sandstone, were encountered. Their size and random distribution resulted in both blasting and quality control problems. By the fourth year of operation, production costs became prohibitive and the site was abandoned. Prior to dismantling the plant a geologic investigation, which included shallow seismic and resistivity surveys, was made of the unmined portion of the lease. The collapse dolines appear to be related to structure and predate development of the modern topography. Surface indications of these features are few. The seismic profiles were especially helpful in plotting their distribution. Geologic relationships and seismic data developed at this site are being related to similar suspect areas in Missouri and have been useful in their evaluation.

Jan 1, 1970