Search Documents

By Michael Rieber

Capable of establishing a net present value of zero over a short period of time small mines, though not simply scalers of large operations, minimize market risks and reduce investment capital. Particularly now they are relevant to LDC development. Small mine concepts are reviewed with emphasis on sizing, speed, and LDC problems. The special problem of gold and the precious metals is examined with respect to mine evaluation. Small mine analysis is introduced with emphasis on the financial model including gold price forecast considerations.

Jan 1, 1987

By Shelley M. Burg, Dennis K. Poulton, Robert B. Gordon

This project includes the excavation and concrete lining of approximately 18 900 m (62 000 ft) of 5.5 m (18 ft) finished diameter subway tunnel for the Los Angeles MTA. The project required that four soft ground headings be excavated from a single shaft located near the mid point of the tunnels. The tunnels were classified "gassy" during the excavation phase. Because of the contract schedule requirements and the limited urban work site available, many logistical problems had to be overcome during the project while excavation was accomplished at a record setting pace. Some unique project features include the muck handling system and an access shaft using a high strength tieback support system. In order to accomplish the work, an extensive effort to plan and construct the main work site was required.

Jan 1, 1995

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Limited contracted to sink a 1500 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.5 ft) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (15 ft.) diameter double-drum hoist to sink the shaft with 12.5 tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1991

By Naj Aziz

Both bolt profile shape and spacing (rib spacing) have been found to influence the bonding capacity of the grouted rock bolt. The bolt surface profile configuration has greater importance to rock bolting in strata reinforcement in mining than the steel rebar used in civil engineering construction. This is because a rock bolt in mining usually is subjected to greater dynamic loading than the steel rebar in civil engineering construction. The increased bonding capacity of a bolt is important when supported ground is either heavily fractured, faulted or the supported ground is of soft formation, typically that of coal measure rocks. Past laboratory studies have identified the bolt profile spacing as of significant relevance to bolt resin rock bonding increase, however, no attempt has been made to determine the optimum spacing between the bolt profiles spacing. Accordingly, a series of laboratory tests were carried out on 22 mm core diameter bolts, commonly used in Australian mines, installed in cylindrical steel sleeve. The study was carried out using both push and pull testing methods. The push test was carried out in 150 mm long sleeves while the pull testing was conducted in 115 mm long sleeves. Profile spacing tested include, 12.5, 25.0, 37.5, and 50 mm lengths. Additional studies undertaken include modelling the profile of the load-displacement data of pull testing. Bolts with a profile spacing of 37.5 mm were found to provide optimum load bearing capacity as compared to other tested profile spacings.

Jan 1, 2009

Production reporting is a natural computer application and is often one of the first applications implemented by new computer users. Automation of a manual reporting system is a good place for new computer users to gain computing experience because generation of basic reports - is fairly straightforward, and automation can often be justified easily on the basis of clerical cost savings. Computers are particularly well-suited for reporting applications which generally satisfy the criteria for effective computerization. Three characteristics must be present to effectively utilize a computerized system: 1) The potential application must be precisely definable. If an algorithm for data processing cannot be developed, data cannot be processed. 2) The operation to be performed must be repetitive. If a particular function is only going to be performed once, computerized systems development is probably not justified. 3) The volume of the data to be processed must be relatively large. If only a few items of data must be manipulated, manual methods are probably adequate. Although a computer can perform only a few functions (it can compute; it can make comparisons; it can rearrange data), it can perform these functions much faster and more accurately than a human being can. The ability to classify and reclassify data in a variety of ways and the ability to summarize data make the computer an ideal tool for production reporting. Production reports can be classified into three major categories, depending on their purpose. Reports can be used for (1) informative, (2) analytical, and (3) control purposes.

Jan 1, 1979

By Rui Xiang Yang, Cong Li, Jia Zeng, Rong Liang Zhang, Wei Zhang, Chao Fan Tang

This research took the roasted products obtained by leaching copper (Cu) refining slag using waste acids and roasting leaching residues with calcium oxide (CaO) as raw materials and used oxidative leaching to extract Cu from roasted products using waste acids. Influences of the leaching temperature, liquid–solid ratio, and sulfuric acid ( H2SO4) concentration in waste acids on the leaching rate of Cu in the oxidative leaching process of roasted products using waste acids were investigated. The unreacted-core shrinking model of heterogeneous reactions was adopted to reveal the leaching kinetics of Cu in the oxidative leaching process of roasted products using waste acids. Results show that the leaching rate of Cu reaches 91.68% when the leaching temperature, liquid–solid ratio, H2SO4 concentration in waste acids, and injected airflow are 80 ℃, 8:1, 1.5 mol/L, and 200 mL/min, respectively. If the leaching temperature is below 80 ℃, the leaching process of Cu is controlled by the solid-film diffusion, and the apparent activation energy Ea is 11.0835 kJ/mol; at a leaching temperature above 80 ℃, the leaching process of Cu is governed by the interfacial chemical reaction, with an apparent activation energy Ea of 42.3183 kJ/mol. The liquid–solid ratio can positively influence the reaction rate constant. The apparent order of the leaching reaction of Cu is 0.632.

Jan 11, 2023

By Charles A. III Cravotta

Streamflow and water-quality data for the northern part of Swatara Creek, which drains a 112-km2 area in the Southern Anthracite Field of east-central Pennsylvania, indicate iron, copper, and lead, and to a lesser extent manganese and zinc, are transported with suspended particles during stormflow conditions. During stormflow conditions, concentrations of these constituents typically peak prior to peak stream stage as a result of scour and transport of streambed deposits. In contrast, sulfate is transported mostly as a dissolved ion. Concentrations of sulfate, specific conductance, and pH are inversely related to streamflow, indicating dilution and acidification during stormflow. This effect is attributed to the mixing of poorly buffered stream water having pH 6.0-6.5 with weakly acidic storm runoff having pH 4.0-4.5 and low dissolved solids.

Jan 1, 2000

By BARBOSA AMILTON, Denise C. R. Espinosa, David B. Dreisinger

Chelating resins can be used to recover important metals from different sources, and it is important to understand which resin is most suitable for each metal [1]. This review  benefits the mining industry because chelating resins can be used to recover metals from low-grade ores and mining tailings, increasing the industrial process efficiency [2–4]. Furthermore, the use of chelating resins in mining processes and mining tailings has the common problem of metals contamination, with iron being the main contaminant in low-grade ores and tailings. Understanding how contaminants decrease ion exchange efficiency is significant for industries [5

By Brian Burdett, Terry I. Mudder, Robert T. Richins, James A. Stevenson, Michael M. Botz, Alan L. Wilder

The first Cyanisorb process was constructed in 1991 at the Golden Cross Mine in Waihi, New Zealand to recover cyanide from CIL tailings. The Golden Cross operation consists of an open-pit and underground gold mine with a conventional crushing, grinding and CIL circuit with Merrill Crowe zinc precipitation for gold recovery. Prior to disposal in the tailings pond, slurry tailings are stripped of cyanide at a pH of approxi­mately 7.5 using the Cyanisorb process. Mill throughput is approximately 2,500 tons per day (TPD), and CIL slurry tailings average 37% solids with a specific gravity of 1.27. CIL tailings WAD cyanide average 150 mg/L. The Cyanisorb process recovers approximately 85% of tailings WAD cyanide, produc­ing a slurry effluent with approximately 20 mg/L WAD cyanide. A second Cyanisorb process was commissioned at the NERCO DeLamar silver mine in southwest Idaho in May, 1992. The ore milling and silver recovery operation consists of crushing, grinding, a CIP circuit and Merrill Crowe zinc precipi­tation for silver recovery. Cyanide recovery is from clarified tailings with WAD cyanide ranging from 3 50 mg/L to 600 mg/L, producing an effluent with less than 30 mg/L to 60 mg/L WAD cyanide. Due to the presence of zinc-cyanide complexes in mill tailings resulting from the Merrill Crowe process, cyanide is stripped at a pH of approximately 5.5.

Jan 1, 1995

By Edgar W. Sawyer

Attapulgite and sepiolite are the clay minerals used to thicken ionically contaminated watzrs in the preparation of drilling fluids. They are nonsweliing clays that can be dispersed and reflocculated by mechanical means to increase the viscosity of fresh water and salt and gypsum contaminated waters. Those gelled in fresh water do not become excessively thick when contaminated with high salt concentrations or polyvalent cations encountered during drilling. Gels formed exhibit thixotropy and yield pseudoplastic rheological behavior due to the particle interactions and mechanical interferences of the flocculated gel structure.

Jan 1, 1983

By William E. Souder, R. J. Evans

From time to time, major technological innovations arise that alter the time-honored ways of doing things. Such innovations can dramatically benefit society in terms of new products, increased outputs, reduced costs and general modernizations. However, the advent of these types of technologies is likely to be resisted because of their uncertain potentials, and because they disrupt established routines and industry patterns. This paper reviews the case history of water jet coal cutting, and assesses its potential to become a major innovation within the next decade.

Jan 1, 1983

By E. F. C. Ferrett

The benefits derived from the use of main fan evasees or diffusers are well known. If a well designed evasee is fitted to a fan either more air will flow through it or the same air flow rate will be discharged at a lower fan speed. This latter possibility will reduce the air power requirement of the mine, the fan input power and the overall energy costs. Despite these apparent advantages, many reports have been received from the industry of poor evasee performance. After examination, it appears that these problems are often caused by installation difficulties or inaccurate design procedures. The performance of an evasee is affected by several independent factors. Some of these factors describe the evasee geometry whilst others are concerned with the behaviour of the air as it passes through the evasee. This paper shows that the divergence angle is by no means the only ;important parameter which affects evasee performance and that the size of the inlet boundary layer has a significant influence. The performance of evasees of differing geometric shape are compared and the criterion to be used for optimum performance is discussed. It is shown that the commonly used evasee efficiency is a poor indicator of good performance. Recent work by the author and others is evaluated and a simple design. guide discussed. For more sophisticated work, details of a. computer program are provided. Finally, a brief resume of the performance of truncated diffusers is given. Since compressibility effects can be ignored for most mining applications, incompressible flow has been assumed for most of this paper.

Jan 1, 1980

By A. Papandreou

Industrial wastes nowadays constitute one of the most serious threats for the future of our planet. Researchers around the world have very often proposed many kind of solutions in the management problem of industrial effluents. However in most cases suggested solutions are either too expensive to be applied in industrial scale, or they just transfer the problem (e.g. precipitation creates dangerous sludge) and so they create an even greater problem and threat. In the present study the exploitation of valuable hydraulic and adsorption properties of fly ash is studied. Fly ash can easily and cheaply be shaped into stable pellets. After ageing for a sort period of time, these structures can be used as adsorbents for the removal of heavy metals from industrial effluents. Experiments in aqueous solutions have shown excellent adsorption behavior concerning the removal of cadmium, copper, lead, chromium (III) and zinc. The advantage of this technology, except low cost, is that after saturation the pellets can be easily removed from the liquid phase and stabilized in concrete structures without any problem of desorption or leaching. Moreover in these structures a significant amount of cement in the concrete can be replaced by raw fly ash. (Ashcrete as it is called). The utilization of an industrial byproduct as fly ash in the form of pellets as adsorption means and their stabilization with concrete (or ashcrete) combines the useful properties of a solid waste in the treatment of liquid effluents and constitutes a green low cost technology.

Jan 1, 2006

By Alfred G. Hoyl

The small miner and small mine have an important role to play in the finding, developing and production of our mineral resources. "Help, not hinder" must be our byword. We must push in every way we can devise to change the adversary position of government and environmental movements. We need the small mines and they must be encouraged, not hindered. Technically excellent and adequate equipment is available, and needed information is also available to the small operation. Environmental questions and problems must be fully considered regardless of the size of a mining operation.

Jan 1, 1987

By Martín A. Encinas-Romero, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, Patricia Guerrero-Germán, José R. Parga-Torres, Luis S. Quiróz-Castillo, JESÚS L. VALENZUELA-GARCÍA

Pressure oxidation is a hydrometallurgical oxidative pretreatment for refractory ores, such as sulfide ores. Here, simultaneous alkaline pressure oxidation and sodium cyanide leaching treatments were carried out on a pyritic ore from the Mulatos Mine located in Sahuaripa, Sonora, Mexico. Mineral characterization, agitation leaching, hot cyanidation under atmospheric pressure conditions, simultaneous moderated pressure oxidation and leaching, and kinetic testing results are shown. The modified variables were temperature, pressure, and cyanide concentration. Characterization indicated that pyrite was the main mineral. Simultaneous pressure oxidation and leaching experiments were conducted at a temperature range of 40–80 °C, oxygen pressure of 87.5–200 psi, and cyanide concentration of 0.8–1.2 wt% in a 2-L Parr pressure reactor. A dissolution rate of 81–86% was achieved under the following conditions: 87.5 psi, 80 °C, 0.8 wt% NaCN, for 1 h.

May 7, 2020

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) multiple seam interaction between web and barrier pillars in superjacent mines, ii) subsidence and caving propagating to overlying seams and mines, iii) pooled water and the potential for inundation resulting from a breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, iv) the presence of overlying or underlying mine workings where pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist.

Jan 1, 2009

By J. E. Oberholtzer, M. G. Fernald

INTRODUCTION Approximately six years ago the U.S. Bureau of Mines (USBM) developed a data acquisition system (DAS) specifically designed for measuring radon levels and other environmental parameters during studies of means to control radiation hazards in underground uranium mines. The DAS system records data in machine readable form using a paper tape punch, which represented the state-of-the-art at that time for a moderate cost output device. However, the use of paper tape as a recording medium for field studies is somewhat unwieldy. Reducing the raw data required either that the tape be shipped to a computer center equipped with a high-speed paper tape reader or that the tape be transmitted at low speed over the telephone lines to a remote computer. Transmitting, at ten characters per second, the data from a 10-channel DAS taking Four readings per hour would require about 30 minutes For each 24-hour day's data. Telephone lines from remote mine sites are often of marginal quality and data errors can be introduced during transmission. Paper tape punches are also prone to occasional punching errors. Both problems make it necessary to carefully check for and correct data errors, a process which is possible because each DAS produces an independent printed data record, but the error checking and correction process can be quite laborious. Aware of recent advances in microcomputer technology which have brought the price of a personal computer down to about the cost of a paper tape punch 5-10 years ago, the Bureau decided to explore the feasibility of using a low-cost personal computer in the field to process DAS data in real time. On behalf of the Bureau, Arthur D. Little, Inc., developed a simple interface circuit which permits an Apple II computer to accept data from one or two DAS units as it is being transmitted to the paper tape punches. Computer software converts each measurement to appropriate engineering units, e.g., radon concentration, Working Levels, air velocity, temperature, or barometric pressure. The computer also calculates 1-hour and 8-hour running averages of all converted data and prints those results as soon as they are obtained on a line printer located at the test site for immediate inspection. After development, the system was used continuously and successfully for a 5-month period at a Utah uranium mine. DAS DESIGN AND MODIFICATION Each of the two USBM data acquisition systems used in this work consists of two separate modules. A multiplexer module located below ground near the measurement transducers acquires signals from each of nine tranducers. Six input channels were devoted to measurements of radon or Working Level. The outputs of those transducers, photomultiplier tubes or G-M tubes, respectively, are digital pulse trains which are accepted directly by the mutliplexer. Three channels were used for environmental parameters--air velocity, temperature, and/or barometric pressure. Each of the environmental tranducers is fitted with dedicated linearizing and voltage-to-frequency conversion circuitry so that the outputs to the multiplexer are also pulse trains having frequencies of one tenth of the value of the measured parameter expressed in the appropriate engineering units. A 100-Hz reference signal was input into the tenth channel for use in monitoring system integrity and performance. All ten pulse trains are then timeseries multiplexed into a signal line for transmission to the above-ground data acquisition module. Above ground, the composite signal is de-multiplexed into ten separate lines, each of which is connected to a digital counter which converts the pulse train to a numerical value. The acquisition of each set of readings is initiated by an adjustable "scan cycle comparator" timer. The acquisition process proceeds in three phases. First, radon and Working Level channels are counted for an extended period of time, typically 5-10 minutes depending on activity, because of the low pulse rates involved. Then the other four channels are counted for ten seconds, and finally, all ten readings, along with the Julian day and time of day are output serially onto paper tape and printed on a strip printer. When the scan cycle comparator reaches its preset time (15-minute cycle times were used in this work), it resets itself, initiates another readout cycle, and begins timing again. The only modification made to the data acquisition systems used in this work was to disconnect the scan cycle comparator in one unit, which became the "slave" and bring in the scan cycle comparator signal from the other unit, the "master", to initiate data acquisition cycles in the slave. Synchronizing the two data acquisitions in this fashion and using two slightly different radon counting times insured that the two systems never attempted to output data to the Apple II at the same time. THE APPLE II COMPUTER The Apple II computer used in this work was equipped with 48 KBytes of semiconductor random access memory (RAM), two floppy diskette drives, a Centronics Model 730 impact matrix printer and a modulator for driving an ordinary color television as a video display device. A single California Computer Systems Model 7720A dual 8-bit bidirectional parallel input/output (I/O) card was installed in the Apple to accept the digital data from both data acquisition systems. This card is

Jan 1, 1981

By Paul D. Chamberlin

The evolution of heap and dump leaching has followed the development of agglomeration, materials of construction for leach pads and ponds, solution distribution systems, testing techniques, and state regulations. They are now mature processes. Possible future directions and developments are discussed. In situ leaching of precious metals is waiting to be commercialized. Regulators are reluctant to allow the use of cyanide because of the potential for excursions and operators are reluctant because of the potential for lawsuits. Developments in alternative lixiviants are needed before in situ leaching is accepted.

Jan 1, 1989

By Peter J. Szabo

The mining executive works in a cyclical industry. His employment is subject to the vagaries of the marketplace. Boom and bust has always been the industry's story. "Big oil" failed in its mining effort. This left emotional and financial scars on many mining families. One must remember that mining executives always play a high-stakes game. Given the cyclical nature of the mining industry, mining executives need to take care of their own financial security. The mining executive that does not plan for his financial security in this cyclical business is playing Russian Roulette with his future. Take a look at those people who have reached their later years with the mining industry. One usually finds three categories of people. Those few in the first group have been fortunate enough to have worked for one company. They have survived the winnowing process of cyclicality, political problems, and takeovers. They have reached normal retirement age. For them, the retirement years are usually comfortable. People in the second group have worked for those same mining companies. But these people have been forced out by early retirement. Or they have been laid off for cyclical, takeover, or political reasons. The third group includes those who have held many positions in the mining industry. Probably not until their later years are they fully vested, if at all, in a pension program. The first small group, then, is the exception. The others, unless they have taken care of their financial security, are doomed to later years of financial problems, stress, and unhappiness. Too late in life, many realize the harsh realities of failure to plan and implement a personal financial program. Mining executives go to some of the world's leading mining schools, to learn how to make money. The curriculum is technically strong. Most mining graduates are familiar with the intricacies of discounted cash flow, present value, and the Hoskold formula. But few of these same mining schools require courses on personal financial planning. Such courses could give mining students a realistic foundation and the mechanisms with which to cope with their cyclical profession. An executive has only three sources of money. He can make money at work. He can put his money to work. Or he can get money from charities, such as government programs. Of these three sources of money, money at work has the best chance of providing financial security in later years. The mining executive must think of the day when he will be too old to work and contribute to the market place. At this point, the quantity and quality of his investments will determine whether his later years will be secure. Along with the Mining Engineering Handbook, two key books should be included in the mining executive's library. These are Venita Van Caspel's The Power of Money Dynamics and Benjamin J. Stein's Financial Passages. These books contain the basic concepts of personal financial planning so critical to an individual's financial survival. Venita points out the simple formula that is the key to financial independence: Time + Money + American Free Enterprise (Rate of Return) = Opportunity to Become Financially Independent Chart 1 shows that this is not a trite formula. The chart shows the dramatic effects of compounding over time. The chart also shows at various yields what a $2000 a year Individual Retirement Account (IRA) contribution will accumulate. Chart 1 (from Money magazine) is based on the future value of an ordinary annuity. It shows that the key to amassing a small fortune by the time a person reaches his 50s is starting to save methodically in his 20s. This, coupled with the highest yields consistent with safety of principal will ensure financial security. There are significant effects from compounding money over time. Every year the decision is put off to save for later years will cost a person dearly by the time he reaches his 50s. For example, consider the decision to put off for one year a $2000 IRA investment at a 12% return. Starting it at age 31 instead of 30 will cost the executive almost $100,000 by age 65. What if the executive waits until age 35 to get started with his $2000 a year investment? He will then lose nearly $400,000 by age 65. Stated another way, the executive costs himself this $400,000 simply because he did not invest $167 a month for five years. $167 a month - that's less than an inexpensive second car payment. This $400,000 pool of money could provide the executive a $40,000 a year income at age 65, assuming a 10% return on invest-

Jan 11, 1985

By Kal V. S. Sastry, Stephen N. Little

Computer simulation of comminution systems is found to provide significant cost savings by enabling efficient circuit design and development of control systems. These simulation systems are based on sound mathematical models and numerical methods. Nevertheless, they are found to be hard-to-use and hard-to-modify to carry out more elaborate process analysis. This paper discusses the fundamental principles and practical aspects of an advanced, highly functional, and user-friendly SIMulator for COMminution, SIMCOM, that is being developed at Berkeley by incorporating state-of-the-art software engineering principles.

Jan 1, 1992