Search Documents

By C. J. Myers, D. L. McKinnon, A. A. Dasys

In 1988, the National Institute of Occupational Health and Safety (NIOSH) published an information bulletin stating that whole diesel exhaust should be considered a probable carcinogen. Since then, regulations across Canada and the United States (Mine Safety and Health Administration, MSHA) have looked at appropriate exposure limits for underground mine workers. In Canada, an interim standard of 1.5 mg/m3 Respirable Combustible Dust (RCD) has been adopted by some provinces and is being looked at by others. MSHA is considering levels as low as 0.5 mg/m3 soot. Golden Giant, being aware of regulatory developments, decided to look at means of reducing diesel particulate on thier large production machinery. This machinery (LHDs and haulage trucks) is powered by Detroit Diesel 71N Series engines and is used to produce 3000 tonnes of ore/day with a longhole mining technique. Having looked at the various control technologies, it was decided to evaluate the potential of using diesel particulate filters with a copper-based fuel additive for regeneration (the process by which collected particulate is burned off). This paper outlines the control technology used and the results of the field evaluation indicating the benefits to the underground mine worker.

Jan 1, 1993

By Joe M. Bryan, George E. Rodger

The development of small precious metal mines in the western states has been directed at heap leach operations. Crushing plants are an essential adjunct to heap leach operations. They must meet environmental air quality regulations which generally follow a similar pattern from state to state. Prior to mine construction a permit must be obtained and an operating permit granted during or shortly after the start-up period. The typical construction permit application consists primarily of drawings, specifications and an explanation sufficient to indicate that the mass of particulate matter entering the atmosphere is below minimum standards. The operating permit may be granted following demonstrations that air emission control equipment or methods comply with information submitted in the construction permit application.

Jan 1, 1987

By AJIT SWAIN, SUNATI MOHANTY

The ability to predict the dewatering performance of an industrial hydrocyclone from a laboratory-model hydrocyclone is of great importance. In this study, laboratory-scale hydrocyclone experiments were conducted using silica sand samples at 10 percent solid concentration for dewatering with Mozley hydrocyclones with diameters of 2 in. and 4 in. The objective is to predict the design parameters for an industrial dewatering cyclone to achieve higher solid concentration in the underflow. A model was developed based on the Nageswararao hydrocyclone model with the help of a commercial simulator for a hydrocyclone operating at 100 t/h and 20 percent solid concentration to achieve 80 percent solid recovery at 45 percent solid concentration in the underflow.

Mar 1, 2023

By HONGWEI YANG, Lili Zhang

Copper slag is mainly used in cutting tools, abrasives, asphalt pavement, road construction, and in the production of concrete as an alternative to sand and cement [1]. As a renewable resource, only about 15-20 percent of the slag is used for these applications, and the dumping or disposal of surplus unused slag results in waste of a certain amount of usable metal in the feedstock [2]. In this work, the oxidation behavior of copper smelting slag under nonisothermal condition is studied using data obtained by the thermogravimetric (TG) method, and the kinetics parameters and reaction mechanism of oxidation are determined. It provides a theoretical basis for the comprehensive recovery of iron resources in slag and the selection of reasonable slag-making conditions.

Oct 1, 2022

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine's strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

By P. R. La Pointe, H. C. Ganow

The production of both over- and undersized coal fragments is a constant problem to open pit operators in the Powder River Basin. Operators strive to achieve production blasts that economically minimize the weight percentage of over- and undersize coal. However, natural fractures influence blast fragmentation, and can impose limits on the final fragment size distribution. ARCO&apos;s Anaconda Minerals Company studied the limits placed by natural fracturing as part of a wider geotechnical study of the Wyodak Coal in the eastern Powder River Basin, Campbell County, Wyoming. Measurements of fracture orientation, size and spacing were made at ARCO&apos;s Black Thunder Mine. These data were used to form statistical distributions for natural fracture size, spacing and orientation. An algorithm was created to select fracture properties at random from these distributions and to form hypothetical blocks. The blocks were then numerically "sieved" to derive pos- sible particle size distribution curves. These curves are compared to fragmentation results from samples taken from three test blasts. All test blasts yield very similar lognormal fragment size distributions. The median particle size varies from 1.25 to 2.0 in.(3.2 to 5.1 cm), the mean from 4.0 to 8.5 in. (10.2 to 21.6 cm). The standard deviation was about 1.6 in. (4.2 cm). Coal fines (fragments < 0.25 in. or 0.64 cm) are about 15%. Calculated fragment distributions for the natural fractures predict the median size well but underestimate the variance. Algorithm modifications to account for processes known to occur in the comminution zone near the blast hole significantly improve the match in the fine coal size range. The match suggests that spacing of fractures, rather than fracture length, controls the formation of fine- and medium-sized fragments. On the other hand, the oversize coal is controlled by the fracture lengths, rather than the spacing. Data from subsequent test blasts support this idea. By increasing delay times from 8 msec to 17 msec, engineers were able to reduce fines to 7% - 10% but could achieve no further improvement, despite changes in shot pattern geometry, decking and hole size. The hypothetical fragment distributions show that, even without blast enhancement, about 5% of the natural coal blocks are fine-sized.

Jan 1, 1986

By H Sohn, R. R. Fernández

Microscopic gold inclusions in sulfide minerals cannot typically be extracted by conventional cyanidation. The gold ore must be pretreated to oxidize sulfide minerals associated with gold and to remove other minerals and chemical compounds that interfere in the cyanidation leaching process. The recovery of gold from refractory sulfidic-carbonaceous ores after roasting pretreatment was studied. With the addition of an oxygen-containing gas (e.g., air or oxygen-enriched air), sulfides of iron, zinc. copper and other metals are tramformed into solid oxides or sulfates and gaseous sulfur dioxide at elevated temperatures (e.g., 400° to 800°C). When the sulfides are oxidized, individual particles lose internal volume and become porous, allowing leaching solutions access to the gold. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent on the roasting conditions and roasting method. The optimum combination of particle size, roasting temperature, reaction time and oxygen concentration in the off-gas was determined for a typical refractory sulfidic-carbonaceous ore from the Carlin Trend in Nevada. The tests were run using a 150-mm laboratory rotating tube furnace and 160- and 200-mm.fluid-bed pilot roasters. Laboratory results indicated that the maximum gold extraction was 92%, with the head and the leach residue containing 5.7 and 0.4 g/t (0.166 and 0.013 oz/st) Au, respectively. The maximum extraction was achieved under the following roasting conditions: a top particle size of 150 yin, a residence time of 2 hrs, a roasting temperature of 475°C and with 40% oxygen (by volume) in the off-gas. Similar results were obtained from circulating fluid bed (CFB) pilot-plant testing. The maximum gold extraction was 90%, with the head and leach residue containing of 5.1 and 0.5 g/t (0. 149 and 0.015 oz/st) Au, respective) v. These results were achieved with the same particle size and oxygen concentration as in the laboratory testing but with the roasting temperature of 500 ° to 525°C and a residence time of 30 min.

Jan 1, 2000

By Kal V. S. Sastry

Modeling and simulation are two major tools available to a mineral process engineer for a consistent and systematic process analysis. The application of these tools to the analysis of specific mineral processing unit operations is well documented in the literature; nevertheless, they are used only to a limited extent in the industry. This is because the fundamental principles of modeling and simulation in the context of mineral processing context are not available. This paper represents the first in a series of papers planned to meet this need. General principles of process modeling and a unified mineral process model development methodology are presented. A simple example of model development using the flotation unit operation is given. A discussion of the practical significance, challenges and opportunities associated with mineral process modeling is included.

Jan 1, 1990

By Klimpel. R. R.

Acknowledgments I am honored to be named as a recipient of the Antoine M. Gaudin Award, and I would like to briefly single out four groups who deserve a special thank-you relative to this award. The first group consists of Professor Kawatra, the many international support references that he gathered and the Gaudin Committee itself. I know such things don&apos;t come without considerable effort by many individuals, and I&apos;m grateful for their support. The second group consists of the management of The Dow Chemical Company, the managements of various mining companies and, in recent years, the management of G. S. Technologies, all of whom supported me, financially and otherwise, in my grinding, flotation and other particle-processing work. Operations people are the most overworked and under recognized people in the world, whether they be in the mining or chemical industry. Obviously, without extensive industrial support, especially from operating personnel in the mining industry, almost nothing about the work contained in this lecture would have, or could have, happened. The third group consists of a number of coworkers who have played key roles in specifically implementing the new flotation-product portion of this lecture. Of these, Bob Hansen, Don Leonard, Basil Fee, Simon Isherwood, Fernando Cones and Marty Meulendyke deserve special recognition. They have not only been dedicated, but they have been great to work with. Also in this third group are many members of the international academic community, especially those at Penn State. Professor Leonard Austin must be singled out because he took me as a young mathematically oriented chemist and taught me to be an effective process-oriented engineer. Without this experience, I would not have had the over 30-year career as an engineer, which I have loved. In addition, Len planted the size-reduction-research virus in my blood, which I can&apos;t seem to get rid of. I also need to mention Professor Frank Aplan, whose obvious love of mineral processing and froth flotation helped to create my interest in flotation. Thus, for those of you who don&apos;t like my approach to flotation, it&apos;s all Frank&apos;s fault. The fourth, and certainly not the least, group to thank is my wife, Charlene, and our two sons, Richard and Steven. No one could have a more supportive family. In every sense of the word, my wife has been my partner from the beginningwe were married at the end of my freshman year in college. She has sacrificed much for me, and I will never really be able to express the depth of my gratitude for Charlene&apos;s encouragement, loyalty and support over the past 36 years. General comments on froth flotation The industrial process of froth flotation: Where is it going? I&apos;m here to tell you loud and clear that froth flotation is alive, well, and growing. The inherent characteristics of high mineral throughput per unit of capital, low operating cost per unit of feed, high mineral specificity and high operating flexibility have guaranteed froth flotation an important past and a growing future. As with any evolving technology, there are always trends at the industrial level that are primarily driven by economics. The current trends include: •the movement towards larger and larger equipment, •more alternative equipment designs (e.g., the column cell),

Jan 1, 1996

By Alan L. Mierke

West Virginia&apos;s economy has been closely linked with coal. West Virginia is consistently one of the top three coal-producing states. Its 149 Mt (164 mil¬lion st) produced in 1992 represented 16.5% of total US coal production. In recent years, the state&apos;s economy has experienced a diversification away from its traditional employment base of min¬ing and heavy manufacturing. However, the coal industry remains an integral part of the lives of West Virginians. Coal is mined in 33 of the state&apos;s 55 counties. In many of these counties, the coal industry is the largest private employer and contributor to the economy. West Virginia has three major coal-producing regions. The northern region produces coal high in gas and sulfur content (steam coal). It is consumed primarily by utility and industrial markets. The southeast region produces high-grade coal low in sulfur content but high in carbons and Btu (metallurgical coal). The southwest region produces metallurgical and steam coal. The high-grade metallurgical coal is used in the production of coke for steel manufacturing. Metallurgical coal also comprises the majority of coal exported from the United States. During 1993, West Virginia was the country&apos;s largest exporter of coal, accounting for 44.5% of total US coal exports.

Jan 1, 1995

By Wallace W. Roepke, Richard C. Olson

To adequately attack the longwall dust problem, the US Bureau of Mines funded a contract to define dust sources on a longwall mine face area. The study examined the shearer during sumping, cutting, and tramming, the conveyor, and the roof supports. Tests showed the shearer to be the major dust source. Introduction Long-term illnesses place a heavy burden on miners, the mining industry, and taxpayers. Black lung payments to more than 400,000 miners and their survivors exceeded $9 billion between 1970 and 1980. They are continuing at a rate of $1 billion per year. Recent MSHA data indicate more than 50% of the longwall faces are still out of compliance with the 2 mg/m3 (0.00007 oz per cu ft) respirable dust regulation. Allowable dust limits are often further reduced owing to the presence of silica dust. This substantially increases the problem&apos;s severity. Research in the 1970s showed that by modifying the mining method through changing drum-type mining machines from high rpm shallow cutting to slow rpm deep cutting, both specific dust and energy could be reduced (Black et al., 1978; Ludlow and Wilson, 1982; Roepke, Lindroth, and Myren, 1976). The coal mining industry is using more longwall equipment to economically obtain high productivity. This high production rate, however, makes it difficult for longwalls to meet the legal dust standard. Research is showing how both these concerns may be addressed at the mining face. Results reported here explain the relationship of various major elements of the longwall system to dust generation on the longwall face. This paper is based on work completed by Foster-Miller Associates Inc. Objectives were to differentiate dust sources on the longwall face and to quantify dust levels for various elements of the shearer drum. The work was accomplished in two phases. Jonathon Ludlow, project engineer for FMA, developed and performed the necessary testing (Ludlow and Marshall, 1983). Bradley, Hadden, and Weston (1983) have done evaluations on British coal mines that produced similar results to those reported here. They found causative rela¬tionships between haulage speed, production, depth cut, drum speed, and dust generation. They also found that roof support movement increased the dustiness, whereas this work indicated that support movement had only a minor effect on total dust exposure. Both of these results are valid when the variation of mining conditions is analyzed. British mines are deeper than US mines. Therefore, roof rocks and coal are more fragmented than in the shallower US mines. Other reasons for the dust differences include the weaker shales found in Britain and the variation of roof support equipment designs between the UK and the US. Four mines in this report had rock roofs and, thus, would be less dusty. The fifth longwall mine had a coal roof, but the large cross-sectional area and high air velocity minimized dust exposure. Mines and Equipment Five underground longwall mine sites were tested (Fig. 1). All were using double-ended ranging-drum shearers (derds) with some variations in equipment. The mines and equipment details are shown in Table 1. No modification of mining equipment or operating cycles was made during the first phase of testing. The mining process observed followed the normal mine operating procedures. Three GCA RAM-1 respirable dust monitors and two vortex anemometers with cycle notations on portable tape recorders were used in each face area. The start and end of each cycle segment were recorded. Dust monitors record the dust levels once every 10 seconds, thus providing a relatively continuous real time indication of change in

Jan 8, 1984

By Jia-Shyan Shiau, Chung-Ken Ho

An uneven gas distribution through the burden layers inside a blast furnace (BF) results in abnormal gas resistance or pressure changes. Rapid variations in the abnormal gas resistance will lead to the occurrence of channeling. A visualization technology mainly made of pressure distribution was developed to predict BF channeling phenomena in this study. The real-time data of BF shaft pressure was used to create a 3D visual model by neural network algorithms and 3D real-time BF pressure changes were observed. The root mean square deviation (RMSD) of the BF shaft pressure was used as an index to set up the predicting criteria of channeling occurrence with the opening of BF Annular Gap Element (AGE), and a predicting system based on the criteria was built. The two criteria for the channeling alarm are the RMSD of the BF shaft pressure (> 0.15 kg/cm2 ) at the upper two levels, and the AGE opening being greater than 60%. This system has been installed in the China Steel Corporation (CSC) BFs, and the test results showed that a prediction can be obtained 8 to 16 min ahead of channeling allowing sufficient time for the operator to adjust the BF operation in order to avoid the occurrence of channeling.

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By Tácio Ferreira, Liz Diaz

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill-and-blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at 345 kt/a (380,000 stpy) generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This article presents how data were collected and design standards reviewed, and the opportunities that were found to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71 percent on the mine’s highwalls.

Aug 1, 2025

By Ramkrishna Agarwal

A low grade iron ore is mined underground at Grace Mine using the panel caving method. Most of the development work is located in footwall. The runways for LHD equipments are heavily supported with steel sets on five foot centers. The sets are embedded in two to three feet of concrete. The initial cost of support is one of the largest single costs of production. During the process of ore-win¬ning, supports frequently fail, necessitating expensive repair. There is no systematic pattern to the failure of supports. A rock mechanics program was launched to isolate causes and their relative contributions to the failure of supports. The preliminary results are presented. A typical portion of a runway is instrumented to monitor rock mass movements around the runway and the corresponding response of supports as various mining activities are carried out in the neighborhood. We believe that such a program is a prerequisite to any remedial measure to alleviate pressure problem at Grace Mine.

Jan 1, 1973

By Charles H. Tiernon

Separation of particles on a table deck* results from differences in specific gravity, plus a number of other interrelated phenomena: size of particles; shape of particles; stratification (consolidation trickling); and hindered settling. The effective use of these factors may be controlled and aided by the following table adjustments: differential action of the drive or head motion; speed of motion; length of stroke; side tilt; end elevation; size of deck area; shape of deck; character of deck surface; riffle design; amount and distribution of wash water; feed water-to-solids ratio; feed rate; and feed uniformity. The typical concentrating table used in the US coal industry is essentially a rhombohedral-shaped deck supported by a suitable subframe. It generally slopes in the direction of the short axis, tilts upward at the refuse end of the long axis, and is differentially reciprocated in the direction of the long axis. This head motion tends to move the particles longitudinally toward the end of the table. At right angles to this movement, wash water (distributed along the high side of the table) tends to move particles down the slope parallel to the short axis of the table. Hence, the natural path of a particle on a concentrating table is from the feed box corner to the diagonally opposite corner of the deck (Fig. 1). There is a natural tendency for heavier particles to sink to the deck of the table and for lighter particles to stay nearer the surface. As a consequence, the heavier particles are carried further along the longitudinal axis since, being on or near the surface of the deck, they are more affected by the table&apos;s reciprocating action. The lighter particles, being at or near the top of the moving bed, travel slower in a longitudinal direction and thus separate from the heavy particles. Wash water and the diluting water in the feed cause lighter gravity particles to move down the short axis of the table. The feed material then fans out from the feed box, where it enters onto the table with heavy gravity particles moving in one direction and lighter particles moving in another. By properly adjusting all of the previously mentioned factors, a clear-cut separation is possible between high- and low-gravity particles, or between refuse and coal. Riffles are of great importance to tabling. They create considerably more capacity than is possible with smooth decks, and they are responsible for better separation accuracy. Particles in their downward movement along the deck&apos;s slope are delayed behind the riffles. Hindered settling, consolidation trickling, and other phenomena occur as the particles tumble over the riffles and stratification ensues. The heavier particles settle to the deck of the table and are trapped behind the riffles, thus insuring their positive movement toward the end of the table. Since stratification and separation of particles are not complete as a result of any one riffle, a series of riffles are used. The cycle of stratification and hindered settling is repeated from riffle to riffle. The result is purer products as particles fan out and progress forward and downward over the table. The smallest, heaviest particles stratify downward to the surface of the deck more quickly and are carried out by table movement toward the refuse end at a faster rate than coarse, heavy particles. Light gravity, larger pieces ride on the top layer of particles and flow down the deck&apos;s slope as a result of the cross flow of wash water at right

Jan 8, 1980

By R. Schipper

Two bench scale biochemical reactors (BCRs) were operated over a period of 3 months for the removal of uranium, radium, and selenium from mining influenced water (MIW). A BCR is an anaerobic reactor comprised of organic and inorganic substrate including woodchips, straw, sawdust, and limestone. Uranium and selenium are removed in a BCR by biological reduction of oxidized species (i.e., selenite, selenate) to less soluble forms (Pahler et al. 2007, Blumenstein et al. 2008, Rutkowski et al. 2013). It is believed that radium may be removed through absorption to the biomass in the BCR. The bench scale BCRs were constructed of 6 inch PVC columns with a top to bottom flow configuration. The bench influent water consisted of three different water ratios from two adit seeps. BCR hydraulic retention times of 24 to 36 hours were targeted during the study. Influent concentrations ranged from 19 ug/L to 1.86 mg/L for dissolved uranium, 12 ug/L to 270 ug/L for dissolved selenium, and 4.9 pCi/L to 24 pCi/L for radium 226. The average and maximum dissolved uranium removal was 93.6% and 98.5% respectively, the average and maximum dissolved selenium removal was 93.3% and 98.9% respectively, and the average and maximum radium 226 removal was 89.5% and 100% respectively.

Feb 23, 2014

By J. R. Sturgul

Thompson and Adler (1988) present a new simulator for use in designing conveyor belt systems for underground mines. Their model uses a large Fortran program to do a Monte Carlo simulation. Their approach is similar to that done by other researchers, such as Stanford (1965) and Newhart (1977). All Fortran based simulation models use an imaginary clock that is advanced a time increment. At each advance of time increment the program has to determine what is to take place in the system. Since many things can take place at different places in the system, this approach requires that a large amount of logic is needed at each step of the program. This, then, necessitates a great amount of jumping between different portions of the program. In fact, the Fortran program, CMBCS, takes up to 15 to 20 minutes to run on the mainframe and several hours for the PC. Such execution times are typical of Fortran based simulation studies. There have been other examples of Fortran based simulation studies in mining. Cross and Williamson (1969) presented a model of a working open-pit copper mine. Fosinato (1982) presented a model of the bucketwheel excavators for the large open-pit mines in Southern Victoria in Australia. These excavators discharge into a complex conveyor system, which can be thought of as being similar, but more complicated than the one modeled by CMBCS. All previous simulation studies using Fortran as the source code have several things in common: they all are very lengthy, often being of the order of 10,000 lines of code and take a great deal of CPU time to execute. The program of Fosinato takes more than 4.5 hours to run on a large mainframe. Also not mentioned by Thompson and Adler is the actual time it took to write the Fortran code. This, too, can be considerable, as Fosinato&apos;s program took several man years to write and de-bug. In order to change it, as the parameters change or as the mine increases, further large amount of time is needed. An alternate to such Fortran based programs is provided by using a special computer language known as General Purpose Simulation System (GPSS). This language is designed to solve a wide variety of discrete event simulation problems and appears to be particularly suited for mining situations as shown by Sturgul and Yi (1 987). Although GPSS was introduced as far back as 1961, it has not been used in mining to any great extent. However, the original form was quite crude and inefficient compared to modem versions. Perhaps with the increasing popularity and availability of these recent versions, this will change. Two such versions are GPSS/H for the mainframe and GPSS/PC for the personal computer. GPSS/H allows for interactive usage, such as allowing input data to be entered via a menu. GPSS/PC has excellent graphical capabilities and one can actually view the simulation in progress. In addition, one can halt the simulation and change values of various parameters. If a particular portion of the simulation is in progress via a concept known as "microwindows." These new versions have greatly increased the potential for using the language for mining situations. Mining applications of GPSS have been given by Sturgul and Yi (1987), Sturgul and Harrison (1987), Sturgul (1987), and Sturgul and Singhal (1988). Schriber (1987) presents a summary of the recent advances in GPSS.

Jan 1, 1987

By Monica Campos, Jose Mujica, Maria Campos

The extraction and processing of metals and other minerals have played an important role in economic, political, and social development worldwide, from the early stages of prehistory to the present day (Gosner, 2020). In other words, mining has been a fundamental part of human civilization, providing the raw materials necessary for technological, infrastructure, and industrial advances. As society progresses, the importance of mining continues to grow, supporting the development of everything from the smallest electronic devices to the tallest skyscrapers (The Importance Of Mining In Modern Society, 2024). The mining industry is closely linked to a country’s economy and activities related to natural resources. The economy of a nation is connected to its extractive industries (Moreira & McMahon, 2014), which have seen dramatic growth in recent years (Pietrobelli et al., 2018). In a context of increasing demand for natural resources, driven by the development of emerging technologies, the expansion of infrastructure, and the foundation of engineering achievements for the coming decades (Importance Of Mining - Minerals Education Coalition, 2024), mining should focus efforts on global development, requiring a comprehensive approach to sustainability that addresses the planet’s needs and protects the well-being, primarily, of the communities and environments where mining operations take place (Figari, 2024). In these areas, diversity and inclusion should be promoted, thus fostering equitable and sustainable development. Speaking of sustainable development, diversity, and inclusion brings us to an interesting topic: the Sustainable Development Goals (SDGs), also known as the Global Goals, which could serve as a key framework for fostering a strong social management culture in mining. The SDGs were adopted by the United Nations in 2015 as a universal call to end poverty, protect the planet, and ensure that all people enjoy peace and prosperity by 2030 (Sustainable Development Goals, n.d.). Companies have compelling reasons to align their actions with the SDGs, as their long-term success depends on healthy communities. This is a major challenge and requires collaborative efforts (Singh & Rahman, 2021). As Fraser (2021) mentions, achieving more sustainable outcomes may involve mining companies and communities working together collaboratively. This research proposes an innovative approach: Inclusive Mining for Sustainable Development, which aims not only to maximize economic profitability but also to promote social and environmental well-being by integrating the United Nations’ Sustainable Development Goals (SDGs), primarily focused on diversity and inclusion. This can be achieved through the implementation of a key value-added initiative for mining companies: the Creation and operation of a corporate volunteering program aimed at developing and executing inclusive practices to promote gender equality, the inclusion of local communities and indigenous peoples, and accessibility for people with disabilities. This proposal will educate employees and stakeholders about sustainability and promote concrete actions through corporate volunteering to strengthen the mining company’s commitment to community development, improve social relations, and advance toward achieving the United Nations’ Sustainable Development Goals, establishing the company as a global change agent.

Feb 1, 2025

By Z. Zhongwei

The leaching kinetic of mechanically activated sphalerite with acid FeCl3 solution was investigated. The result has shown that mechanical pre-treatment has greatly enhanced the leaching process. Comparing with the original concentrate, the activated one can be leached more completely at relatively lower temperature with diluter FeCl3 concentration within a shorter leaching time. The activation energy for the activated concentrate is 27 KJ/mol, while for the original one is 52 KJ/mol.

Jan 1, 1995