Search Documents

By Gerd L. Klinkenborg

Throughout the history of the development of mechanical conveyor systems, it has always been an established condition that loads are received at one end of a single-belt conveyor and discharged at the other end, in a point-to-point, manner. In systems designed for the continuous transport of granular materials, vertical or horizontal changes in; direction have always necessitated two or mope single-belt conveyor units, with a corresponding number of motors, assemblies and attendant mechanical and human or electronic controls. Besides these high-cost factors, every change in the system's direction also calls for a transfer point that involves a drop-back of the material from one level to another with some loss of the material and, in many cases, unwanted additional granulation. Where changes in the location of the discharge point are wanted, the conventional single-belt conveyor must either be replaced by a shorter or longer unit or additional units purchased and installed, or existing units rearranged. This can take days or weeks, and involve special expenditures as well as loss of valuable production time.

Jan 1, 1962

By Shallesh K. Patel, Richard M. Powers, Patrick Zhang

Perceived environmental impacts from flotation reagents used in the phosphate industry have been of concern for nearly a decade. A research program was initiated to determine the distribution, fate, and consequences of flotation reagents (fatty acids, fuel oils, and amines) within the environment. Therefore, laboratory investigations of biodegradation and soil attenuation of the reagents were conducted along with field flotation mass balances and groundwater investigations in clay settling, sand tailings, and undisturbed areas. Sample analysis and a reagent mass-balance model indicated that most reagents are distributed in clay settling and sand tailings areas. Groundwater analyses showed no fatty acids or amines in any of 19 surficial or intermediate aquifer water samples. In contrast, fuel oils were detected in the surficial aquifer at all sand tailings areas in concentrations ranging between 8.5 and 0.5 mg/L. Fuel oil was also detected in trace amounts (0.6 mg/L) in one intermediate aquifer well located in an active sand tailings area. All fuel oil concentrations detected were very low and, coupled with a biodegradation rate of approximately 10% per month, all concentrations should be within reference levels in six months. Based upon the results of this study, use of flotation reagents in the beneficiation process of the Florida phosphate industry present no long-term threat to the environment.

Jan 1, 1999

By Harry R. Dahlberg

Heap leaching is discussed as a unit process. Five factors are identified as the principal elements that can be measured and/or controlled. These are: 1. Material Size 2. Volume of solution 3. Tonnage of heap 4. Time 5. Solution concentretion. The Rate of Extraction Curves obtained from an actual heap or column tests describes the economic viability of the unit process. By analysis of these curves and the five factors end their inter-relationship it is possible to determine how the extraction rate can be increased. The practice of leach and rest used by many operators is analyzed and shown on a hypothetical rate of extraction curve. The influence of the driving force of the hydrogen ion and ferric Lon as Lixivants and its effect on the rate of extraction curve is discussed.

Jan 1, 1979

By Robert B. Fulton, Gill Montgomery

Fluorspar is the commercial name for fluorite, a mineral that is calcium fluoride, CaF2. The name, derived from the Latin word fluere (to flow), refers to its low melting point and its early use in metallurgy as a flux. It is the principal industrial source of the element fluorine. Two other minerals, cryolite and fluorapatite, have significant fluorine content. Cryolite, sodium aluminum fluoride, Na3AlF,, is a rare mineral that has been found in commercial quantities only in Greenland. The natural material has been supplanted by synthetic cryolite for its principal industrial use in the manufacture of aluminum. Fluorapatite, Ca5F(PO3)2, is a source of phosphate for fertilizer manufacture, containing a small percentage of fluorine. Commercially mined deposits of apatite have varying amounts of fluorine, chlorine, hydroxyl, and carbonate. HISTORY Fluorspar was used by the early Greeks and Romans for ornamental purposes as vases, drinking cups, and table tops. Various peoples, including the Chinese and the American Indians, carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola in 16th century Europe. Fluorspar mining began in England about 1775 and at various places in the United States between 1820 and 1840. Production grew substantially following the development of basic open hearth steelmaking, wherein it is used as a flux. Use was stimulated by growth of the steel, aluminum, chemical, and ceramic industries, particularly during World Wars I and 11. Fluorocarbons entered the picture in 1931. The use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel began in 1942. Differential flotation for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s and the application of heavy media concentrating methods to the treatment of low grade ores in the 1940s were outstanding technological advances that facilitated increased production. Pelletizing and briquetting of flotation concentrates for use in steel furnaces and the development of flotation schemes for beneficiating ores containing abundant dolomite and barite have been major improvements in the industry. USES OF FLUORITE Fluorspar is used to make hydrogen fluoride (HF), also called hydrofluoric acid, an intermediate for fluorocarbons, aluminum fluoride, and synthetic cryolite. It is used as a flux in the steel and ceramic industries, in iron foundry and ferroalloy practice, and has many minor specialized uses. Hydrogen fluoride is produced by reacting acid grade (97% CaF,) fluorspar with sulfuric acid in a heated kiln or retort to produce HF gas and calcium sulfate. After purification by scrubbing, condensing, and distillation; the HF is marketed as anhydrous HF, a colorless fuming liquid, or it may be absorbed in water to form the aqueous acid, usually 70% HF. Synthetic cryolite, organic and inorganic fluoride chemicals, and elemental fluorine are made from hydrofluoric acid. The acid itself is important in catalysis in the manufacture of alkylate, an ingredient in high-octane fuel for aircraft and automobiles; in steel pickling, enamel stripping, and glass etching and polishing; and in various electroplating operations. The manufacture of one ton of virgin aluminum requires about 12 to 29 kg of fluorine content in synthetic cryolite and aluminum fluoride. This quantity, through improved technology and recovery practices, is being lowered significantly in countries with the most advanced technology (i.e., Australia and Sweden), while others (i.e., Surinam and South Africa), remain at the high end. Elemental fluorine is prepared from anhydrous hydrofluoric acid by electrolysis. Gaseous at room temperature and pressure, fluorine is compressed to a liquid for shipment in cylinders or in tank trucks. Elemental fluorine is used to make uranium hexafluoride, sulfur hexafluoride, and halogen fluorides. Gaseous uranium hexafluoride is used in separating U235 from U233 by the diffusion process. Sulfur hexafluoride is a stable high dielectric gas used in coaxial cables, transformers, and radar wave guides. Halogen fluorides have important applications, mostly as substitutes for elemental fluorine, which is more difficult to handle. Emulsified perfluorochemicals, organic compounds in which all hydrogen atoms have been replaced by fluorine, are undergoing investigation as promising blood substitutes. They transport oxygen and, in conjunction with a simulated blood serum, perform many functions of whole blood. With further development, these organic compounds may ultimately, in emergencies, be useful in saving lives of animals and humans during periods of acute shortages of natural blood. Inorganic fluorides are used as insecticides, preservatives, antiseptics, ceramic additives, and fluxes and in electroplating solutions, antioxidants, and many other products. Boron trifluoride is an important catalyst. Organic fluorides are volume leaders in the fluorine chemical industry. Fluorinated chlorocarbons and fluorocarbons are prepared by the interaction of anhydrous HF with chloroform, perchlorethylene and carbon tetrachloride, and are characterized by low toxicity and notable chemical stability. They perform outstandingly as refrigerants, aerosol propellants, solvents, and cleaning agents and as intermediates for polymers such as fluorocarbon resins and elastomers. Fluorocarbon resins are inert compounds that have unusually low coefficients of friction and have found a number of applications as lubricants for parts that cannot be oiled, e.g., bearings for window raising equipment located inside of automobile doors, in small electronic equipment, for the manufacture of chem-

Jan 1, 1994

My "outside exploration" began in November 1908, only 16 months after I had come to Bisbee as a raw engineer. The well publicized reputations of eminent engineers up to that time, including John Hayes Hammond, Herbert Hoover, James Douglas, D.C. Jack- ling, J. Park Channing, and a few others had been due to new mines they had found or brought to successful operation. And here was I, a mere youngster, given a chance to join the group. I knew there would be disappointments but I had no idea how many of them. In spite of the many prospects that turned out to be worthless I never looked at a new one without the feeling that this one might turn out to be the big success. This confidence, blind as it was, gave every arduous examination a zest and it made me climb every mountain on which the owner said there was something worth seeing, or on which T could see a distant staining that might mean ore. If I looked at every showing the owner suggested he at least would think I was honest and would bring other properties to our attention. This reputation of never refusing to go to see an outcrop, no matter how hot the desert sun or how rough the terrain, was probably one of my best assets. High as my hopes were at the start, they proved not to be exaggerated and if I were given a chance to do it again I would not hesitate, in spite of the jaundice, rheumatic fever, and other maladies that beset some of the expeditions. On the whole the results have equaled all my hopes. Toward the end of my years of active exploration I totaled up the score. Out of the prospects submitted to us about two out of three were eliminated after questioning the owner or prospector, without an examination. This left about a 1000 mines or prospects that seemed worth at least a preliminary look. One out of seven of these was worth a little development and a seventh of this seventh turned out to be a modest success or better. And nine or ten in all, or one out of 1000

Jan 1, 1976

By K. Anderson

There is a credible, cogent, and responsible argument that mining can be part of a sustainable future in countries with freely elected governments, transparent and enforceable laws, a closure plan with an adequate bond, and a small handful of other measures. This perspective, built largely upon the understanding of mining as a temporary use of the land, is coupled with a growing understanding of economic diversification as a tool to level out the ‘bust’ side of the boom and bust cycle. There are verifiable signs of progress that the sector has, at least in some venues, begun to embrace this view of ‘sustainability’ both in philosophy and practice. While laudable, there remains a conundrum not yet fully explored. It is conceivable that companies can fulfill all legal requirements, practice corporate responsibility in its broadest and most liberal interpretation, and yet leave behind, after the gates are closed and the lights turned off, a situation which is not only unsustainable, but far worse off than before mining started. Having observed this outcome, repeatedly, some critics have concluded that all mining should be stopped. Others recommend that it be vastly curtailed until regulatory regimes are re-vamped, communities fully empowered, and companies brought to heel. Yet others, including many within the industry, are looking to hold back this dark prospect with peer pressure, branding and competition for good will. In this paper, I propose to focus on this discontinuity, that gap wherein the chain of logic breaks and reasonable policies, reason-able choices, reasonable actions, may fail to deliver expected results. I suggest that any meaningful definition of post-closure sustainability must include the concept of human welfare, and increasingly, human security, over and above meeting the requirements of law, beyond retaining shareholder value and reputation, beyond discussions of subsequent land use and diversified employment. I suggest that self-determination, that ability of a people to hold for themselves the vision of their own future, and to have a sense of their power to implement it, may be both the most difficult and the single most important determinant of long-term sustainability in a community. The particulars will vary; a Canadian junior or an Australian multinational, a highly regulated state in the American west or a ‘failing state’ in Africa’s west, gold or sand and gravel. But the recommendation is the same: this must be a collective endeavor, a shared responsibility involving some combination of government, companies, communities, local and international NGOs (non-governmental organizations), each contributing in the ways most able.

Jan 1, 2004

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By Clement K. Chase, Manuel R. Lastra

Introduction The choice of using a dump or heap leaching process or a fine grinding-agitation leaching process is based on the grade and tonnage of the ore body. Low grade ore and small tonnages are best treated by a low-cost method, such as dump or heap leaching. Permeability, however, is the critical factor in a successful leaching operation, regardless of tonnage or grade. Without permeability in the leach bed, no percolation, no dissolution, no extraction, and no success are possible. Solution delivery to the ore is also essential. Solute-to-mineral contact is a requisite. The solute must be effectively strong and not be depleted in active dissolvers, such as acid, ferric iron, cyanide, and oxygen. It must also be moving across the mineral to be dissolved. No pockets of stagnant solution can be allowed. A third factor is recovery of the now-dissolved metal in the pregnant liquor. All such liquor should be gathered at a reasonable metal concentration to make further pumping and processing worthwhile. Control and recovery of pregnant solutions are probably the most ignored factors of solution mining. This stage in recovery is historically where many operations either fail or become viable. Permeability A permeable heap is normally achieved by taking into account heap building/construction and agglomeration/pelletizing. Even though heap building is critical for good permeability, it will not be discussed here. It has been described in detail by others. Instead, this analysis will concentrate on agglomeration and pelletizing. Differences between agglomeration and pelletizing are emphasized. Agglomeration is referred to when small particles are being attached to larger particles -the ore presents a complete size distribution. On the other hand, pelletizing is a process where all particles are fine (less than 850)µm or 20 mesh), as with mill tailings. The difference is important from two points of view: • Mechanical devices used to achieve the desired attaching action; and • Binder dosages. Mechanical Devices Due to the absence of large particles that fines can become attached to, pelletizing should be done in a centrifugal-action-based device, such as an inclined rotating plate, a rotary drum, or a series of belt-transfer points. In agglomeration, large particles play a part as a natural nucleus for the attaching action of fines. Hence, a tumbling action as strong as for pelletizing is not required. Common methods to accomplish agglomeration include: • Cascade belt system with either all belts moving forward or some of them moving forward and at least one moving backward; • Combination of belt plus inclined vibrating chute; • Large concrete mixer drum; and • Belt discharging directly onto stockpiled ore. The proper agglomeration system will depend basically on the size distribution of the ore and the amount and type of clays present. In all of the agglomerating systems described, the tumbling action takes place at the transfer points either from belt to belt, or from belt to inclined chute ore belt to ore pile. Usually, two or three mixing bars at each transfer point are also included to help the mixing action. Plows to move the ore around on a moving belt are also used.

Jan 11, 1984

By S. Bhattacharjee, S. K. Singh, R. K. Galgali

A method for the preparation of zirconia- toughened mullite using dc plasma is presented. An indigenously developed 50-kW thermal plasma reactor is used for the preparation of zirconia-toughened mullite using a dissociated zircon and alumina mixture. Both XRD and SEM studies of the product confirmed the formation of mullite and zirconia. The zirconia grew as equiaxed grains of uniform size (~5 µm) in a mullite matrix.

Jan 1, 2002

By Frederick Schwarz

At the El Realito project, Sonora, Mexico, the Luz del Oro joint venture has recently inferred a geologic resource of 400 to 800 kt of 2.5 glt gold potentially present in gossans, breccias, and veins. El Realito, under investigation for a dump leach, open pit operation, is located in the Sun Antonio Mining District where gold and silver veins and gold placers have been exploited since Spanish colonial times.

Jan 1, 1990

By Ben L. Seegmiller

The artificial stabilization of a pit slope at the Twin Buttes Mine near Tucson, Arizona has been completed as part of a practical rock mechanics program. The research program began in June 1971 as a result of the three million ton South Slope slide(1) which caused significant economic and operational problems. Hydrological studies, field and laboratory testing and investigation of various stabilization systems(2)occupied the first year of research. In July 1972 a design for an artificial stabilization test using post-tensioned cable bolts was completed and the selection of an outside contractor was made the following month. The project began in mid-September and was completed during the first week of January 1973. The test site is located adjacent to the South Slope slide in a zone of high potential failure. When the site was initially selected it was thought that it would remain stable at least until the test could be completed. However, heavy rains which fell in late October induced displacement in the half of the test site adjacent to the South Slope slide. Prior to this stabilization test it was thought both impractical as well as improbable that a moving slide could be stabilized with an artificial support system(3). Because the project was nearing the half-way point it was decided that an attempt should be made to complete the test as originally planned. This meant, in effect, that an attempt would be made to stabilize the moving section as well as the stable section.

Jan 1, 1973

By M. E. Buzon, M. E. Gunter, B. D. McNamee

A Google search on talc asbestos yields more than 500,000 hits due to the growing number of civil lawsuits in this area. Historically, the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos and whether the amphiboles had an asbestiform habit. Ultramafic-hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc, but they can occur in the surrounding black-wall. In these deposits, the serpentinite host rock is in direct contact with the talc, therefore, allegations can be made that non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. We analyzed talcs from both metamorphosed carbonate- and ultramafic-hosted talc deposits using polarized light microscopy (PLM), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), electron microprobe (EPMA) with wavelengthdispersive spectroscopy (WDS), transmission electron microscopy (TEM) with EDS, and powder X-ray diffraction (XRD). Compositions of minerals determined by EDS alone are not sufficient to confidently identify asbestos, despite common practices by some researchers. We emphasize, using both historical samples, and analyses of currently contested minerals, the importance of determining both the structure and composition of a mineral, as well as defining its morphology, before concluding whether it is asbestos.

Jan 1, 2018

By Rubén Pavón] [H.

Mexico, that for various years held the second place among the elemental sulphur producers in the world, now occupies the fourth position. Nevertheless, taking advantage of the recent increase in the international prices of the metalloid, it is expected that Mexico recovers its traditional position producing, for the first time, over two million tons of sulphur during 1974. Drawing from material stockpiled during the last years sales are expected to reach 2.5 million tons, at excellent prices in the foreign markets, but not so in the domestic ones where prices have remained practically static since 1955, in spite of substantial escalation of production costs. Of the two sources of elemental sulphur in Mexico, the frasch process extraction from the salt domes of the Tehuantepec isthmus where the most important reserves are located - is the one that shall have an important increment. An increase of production of lesser magnitude is expected from sour gas, since sulphur recovery plants wilI go on stream toward the end of the year in the new oil fields recently located in the State of Chiapas. Two Mexican corporations are expanding and improving rational Frasch extraction operations. Together with Petroleos Mexicanos' sulphur recovery from sour gas it is estimated that production during 1975 shall reach 2.5 million tons and, consequently, supply the domestic market and generate an important sum of foreign currencies.

Jan 1, 1974

By H. Ouellet, J. Paraszczak

The pneumatic jackleg drill remains a widely used tool in development and production drilling in many small-scale and narrow-vein underground mining operations in North America. Several drawbacks of this technology (unsatisfactory drilling rate, noise, vibration, presence of oil mist, etc.) and the successful introduction of water-powered jackleg drills in South Africa have stimulated the interest of many mine operators. The performance of both drill types have been tested in a mine site in Northwestern Quebec, Canada. Results of the testing of penetration and advance rates as well as environmental aspects are presented. They show a superiority of water-powered drills, even though the difference in performance is less significant than that reported from South Africa. Further research avenues are proposed to better evaluate the potential of water drilling technology in North American metal mines.

Jan 1, 1995

This one day field trip is sponsored by the Denver Region Exploration Geologists? Society, May 14th 2009. The trip highlights major geologic features and some notable uranium occurrences along the north-south mountain-basin boundary southwest of Denver and continuing north to Fort Collins, Colorado. Uranium deposits visited include sandstone?hosted roll front type and polymetallic veins hosted in metamorphic rocks. A replacement ?episyenite? type occurrence is considered via description and hand samples but is not visited owing to logistical constraints. Recovery methods addressed include underground mining and in-situ leach recovery. Samples of Precambrian basement rocks, deposit host rocks, uranium ore samples, and ore polished sections viewed by reflected light microscopy will be available. A road map showing the locations of the stops serves as the front cover of this field guide. The Robinson episyenite-hosted occurrence (not visited) is labeled as Stop 6. A stratigraphic column is provided which shows the position of the host rocks at each stop (Figure 1-1).

Jan 1, 2009

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

By Bruce E. Nesbitt, Paul G. Lhotka

At Lupin mine gold is spatially and genetically linked to zones of hydrothermal alteration in iron-formation which are symmetrically developed adjacent to late Archean quartz veins. Immediately adjacent to the veins, coarse grained, typically gold- and sulfide-poor, calc-silicate rocks are often present. These rocks comprise hedenbergite + quartz ± grossular garnet ± epidote ± scheelite ± calcite. Sulfides (pyrrhotite, arsenopyrite and loellingite) and gold are concentrated in the next zone and occur with hornblende-rich rocks comprised of hornblende, quartz, hedenbergite and grunerite. Furthest from the veins are gold- and sulfide-poor, grunerite-rich iron formation comprising grunerite, quartz, hornblende and sometimes magnetite. Although the alteration assemblages have similarities with skarns, they develop in iron formation, and are at best indirectly related to intrusive igneous rocks. Geological and geochemical data clearly indicate the calc-silicate rocks are metasomatic in origin.

Jan 1, 1990

By G. C. Anderson

The Cleveland Cliffs NOLA electronics and software upgrade is a Windows based system that simultaneously controls two Texas Nuclear NOLAs and associated sampling. It uses new spectrum analysis and algorithms to produce accurate, linear silica measurement with slurries that range from 5 through 50 percent solids. This linearity allows us to achieve a reproducible procedural calibration. The hardware consists of readily available shelf items, is extremely redundant and eliminates all NIM bus modules.

Jan 1, 2003

By Anil Kumar

In underground mine production units that employ discrete-vehicle face haulage, feeders are used in the belt network so that vehicles can unload rapidly without transmitting to the conveyor network the high material flow rates that result from rapid unloading. They prevent production bottlenecks at the face, while reducing capacity requirements for downstream materials handling equipment. Similarly, surge bins may be installed at intermediate locations in the network to smooth flows from a number of upstream sources, thereby reducing downstream belt capacity requirements. This paper introduces new stochastic process models to temporally describe loading patterns from unit operations and techniques for computing the probability of various fill levels for the feeder or surge bin. These results may be used to analyze the effect of alternative bin or feeder capacities and discharge rates on the performance and costs of the materials handling system.

Jan 1, 1994

By Walter Hoecker

The dissolution of gold in cyanide_ leaching has been we11 published with the genera1 acceptance that gold is oxidised by oxygen and stabilized by complexation with cyanide [1]. The dissolution of gold is essentially an electrochemical process. The rate of the anodic gold dissolution is controlled by the cyanide concentration. - (2) While the cathode reduction of oxygen is controlled by dissolved oxygen concentration - (3) There are a number of factors influencing the concentration of oxygen, and if 1owered substanth.lly will effect the efficiency of the leaching plant. These include: "' salinity "' temperature "'partial pressure "'oxygen consumption rate The use of pure oxygen for· cyanidation is only beneficial if oxygen is rate limiting, Conversely a slurry saturated with air (typically 5 - 8 ppm) may not be enough for maximum leach rate. The diagram below shows the maximum dissolved oxygen levels obtainable with pure oxygen and air. DISSOLVED OXYGEN (MAXIMUM) IN WATER At steady state, the rate of the cathodic reaction must equal the rate of the anodic reaction. Thus the rate of gold dissolution is dependent on both the· cyanide and oxygen concentrations. - (4) Using an average of Do/Den =· 1.5 [2] (where Do and Den are the oxygen and cyanide diffusion coefficients) the table below illustrates the maximum effective oxygen concentrations for given cyanide levels in clean water [3].

Jan 1, 1992