Search Documents

By Ben Fahrman

The classical approach to engineering design involves the purely deterministic calculation of the factor of safety, the ratio of strength to stress. The factor of safety is an easy calculation to perform in many circumstances, and it is very easy to interpret the results. The simplicity of the method is both a strength and a weakness. The results of the deterministic factor of safety calculation are simple to determine and interpret, but they have no ability to account for the uncertainty present in the inputs or outputs. Uncertainty is prevalent in geotechnical engineering applications. This uncertainty can stem from spatial variability, poor sampling, a dynamically changing environment, etc. Probability analyses allow input parameters to take the form of a distribution rather than a single value, making them uniquely equipped to handle the uncertainty inherent in geotechnical engineering design considerations. A stochastic approach also has the benefit of providing results as a probability of failure, which is more meaningful than a factor of safety. Though stochastic modeling is becoming more common in many geotechnical applications, it is still not widely used for coal pillar design. The objectives of this study are to justify the concept of using a stochastic approach to coal pillar design and to compare the results of a simple stochastic analysis to those of standard industry practice. A simple synthetic study was performed to compare the results of a probabilistic analysis of coal pillar design to the results obtained from running ARMPS, which is published by NIOSH. Normal distributions were assigned to each input parameter that is required to determine the factor of safety of a single coal pillar. The probability of failure resulting from the synthetic study was found to be more conservative than the ARMPS stability factor. A probabilistic approach to coal pillar design is discussed in comparison to the traditional deterministic approach. The greatest strengths of the probabilistic approach were determined to be the effective handling of uncertainty and the increased meaning of the inputs and outputs inherent to a probabilistic approach.

Jan 1, 2013

By Jurgen te Kook

State-of-the-art for subsidence calculation are stochastical models. Although these models were successfully used all over the world they have their limitations due to the fact that they are not based on mechanical laws. For example the models did not take the rock mass structure and the rock mass characteristics into account. Therefore in a research program the skills of geomechanical numerical models for subsidence calculation were investigated. A case study shows that numerical models which are in principle based on the elastic theory are suitable for subsidence prediction. Due to the principles of these models the results are not sufficient in the case of multiple seam extraction. More extended geomechanical numerical models like FLAC and UDEC were investigated in further steps of the research work. Up to now large area geomechanical models require unrealistic long calculation times if the level of detail is similar to that of small scale calculations. Due to this it was necessary to implement a simplified description of the rock mass structure and characteristics. Different case studies show that this approach is successfull for subsidence calculation by numerical geomechanical models even for multiple seam extraction.

Jan 1, 2008

By Greg Smith

This paper documents the use of bench testing equipment developed to enhance the understanding of, and improve upon, common roof bolt support systems. Most roof bolt systems consist of components that are covered within the scope of ASTM (American Society for Testing and Materials) standards. However, ASTM does not specify testing methods or performance standards for complete roof bolt ?systems?. It only designates testing methods and minimum performance standards for roof bolt ?components?. Improved understanding and continuous improvement of these systems is essential given the enormous impact that they have on the safety and profitability of underground mining operations. Bench testing equipment has been developed that effectively measures and records multiple points of deformation in a rock bolt support system while load is being applied. With this testing capability, an improved understanding of component and system stress distribution can be obtained and devices and methods for visual load indication can be developed. This paper is formatted as case studies where testing was performed to demonstrate load versus deformation profiles and to develop system improvement products.

Jan 1, 2012

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By Changsheng Song

With increasing depth of coal mining in China, the number of coal and gas outbursts has been increasing for years. By means of destressing the protective seam, the gas in the protected seam is drained to reduce gas concentration in the high gassy seams, thus ultimately attaining simultaneous extraction of coal and gas. Base on the simulated material scale modeling and numerical simulation, the protective seam mining method was practiced at No. 8 coal mine in Pingdingshan city. After extracting the No. 15 seam, the overlying strata movement and the deformation of No. 9-10 protected seam were studied. The experiments showed that it was feasible to destress the protected seams with large interburden thickness. As the protective seam was being mined, the protected seam experienced dynamic movement process and the change in vertical stress in the No. 9-10 seam assumed ?W? shape. When the face had advanced 656 ft (200m) from the setup room, the No. 9-10 seam was fully destressed, resulting in easy gas drainage in the destressed zone. Recommendations on mining sequence of multiple seams mining in the Pingdingshan coal areas were made.

Jan 1, 2008

By Nathaniel Schaefer, Christopher Newman, Zach Agioutantis

"As mining reserves continue to be developed in deeper and more complex geological and geometric conditions, there has been an increased demand for underground mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. Current ground control design software are limited to a given device and data files generated can only contain a single design. However, with the growth of cloud computing and increases in internet access, even underground where permissible, web-based software applications allow for in-the-field calculations, as well as collaborations, from multiple users. webGroundControl (webGC) utilizes a multiple-tier architecture, building upon existing NIOSH ground control design software, more specifically ARBS, ALPS, and ARMPS. By providing operators the ability to access ground control design programs from any device, given an internet connection, webGC allows for on demand calculations to ensure underground pillar and roof stabilities with respect to current site-specific parameters, geometries, and geology. Through the development of new features, which aid in design analyses, as well as project collaborations, webGC provides the modern engineer with a more versatile ground control design tool for the improvement of underground health and safety. With the completion of the ARBS, ALPS, and ARMPS modules, this paper introduces potential users within the mining industry to the navigation and operation of the webGC application, as well as its ability to facilitate collaborations between operational personnel and planning engineers. The purpose of this paper is to raise interest in the web-based application before its official launch in Summer 2018."

Jan 1, 2017

By Andre Zingano

The objective of this paper is to compare the behaviors of different types of roof bolts: (1) One-Step Bolt (OSB), (2) Fully grouted Bolt (RB), (3) Combination Bolt (CB), and (4) Torque tension Bolt (TB). Two dimensional numerical models were built for both bolted and unbolted roofs. The geological sequence and rock properties used in the numerical models represent the typical roof condition for Pittsburgh coal seam. Using the unbolted roof as a base case, a comparison is conducted by monitoring the roof vertical displacement at the center of the entry and at the bolt positions, the axial force in the roof bolts, and stress distribution in the bolted area. The grout/rock interface is assumed to be perfect. The estimated roof displacements showed that the differences among the four types of roof bolts are small. The major differences are in the shear stress at the grout/rock contact and in the shear stress along the immediate roof bedding interface as well as in the bolt axial stress. There is less axial stress for the OSB compared to RB and CB as the diameter of the OSB is much bigger and the contact area between grout and rock is twice as large as for RB and CB. The higher strength of the OSB contributes to keep the bedding planes in the roof closed.

Jan 1, 2007

By Nicholas Chlumecky

One of the oldest mine supports in use today is timber cribbing. In many mining operations material, installation and maintenance costs for timber cribbings are substantial. Their performance characteristics also add to mining costs. During the 1970'6, the U.S. Bureau of Mines recognized many of the deficiencies of timber cribbing and very successfully initiated the development of steel-fiber- reinforced (SFR) concrete blocks. Since the early 1980's this SFR concrete cribbing has been manufactured as a high quality product which has found increasing acceptance by mine operators. The rapid acceptance of the SFR concrete block cribbing has proven that its use is eliminating many of the deficiencies of timber cribbing while providing superior load carrying capability. The use of SPR concrete blocks to build the cribbing is based on the same principle as wood. That is, stacking longitudinal, rectangular blocks in layers in a crisscross manner. The blocks are positioned at right angles to the blocks of the layer below. With this situation, the possibility of misalignment exists when the concrete blocks at the base are not placed exactly parallel or when the blocks of the base are subject to unequal settlement. Such misalignments creates localized, high stress areas which reduces the load capacity of the cribbing made from SFR concrete blocks. Recognizing the problem of misalignment, the Underground Supports Division of Commercial Shearing, Inc., conceived a circular, one-piece, steel-fiber-reinforced concrete cribbing which is being marketed under the name - Donut Cribbing. This concept eliminates the possibility of misalignment and provides 100% bearing between layers of stacked cribbing as well as other advantages. The purpose of this paper is to discuss the performance characteristics, installation speed and economical factors of each of the three cribbing types -- timber cribbing, SFR concrete block cribbing and SFR concrete Donut Cribbing.

Jan 1, 1986

By Thomas M. Brady

The Spokane Research Laboratory/NIOSH and the University of British Columbia (UBC) geomechanics group are focusing on the development of safe and cost-effective underground design guidelines for weak rock masses having an RMR in the range of 15 to 45. Weak ground conditions, ground support, and mining methods used in several North American underground mines were observed. The RMR values were calculated to update both manned entry span design and non-entry stability graphs, plus a database on underhand mining methods was created to reflect existing North American mining conditions. The immediate rock mass was characterized and analyzed in terms of prevailing type of ground support, potential failure mechanisms, and rock behavior to define how existing design curves must be modified for the existing weak rock mass. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making sound economic decisions that will also ensure a safe working environment.

Jan 1, 2006

By Syd Peng, Gamal Rashed

"Bumps in coal mines have been recognized as a major hazard for many years. These sudden violent failures around mine openings have compromised safety, ventilation and access to mine workings. Previous studies showed that the violence of coal specimen failure depends on both the interface friction and width-to-height (W/H) ratio of a coal specimen. The mode of failure for a uniaxially loaded coal specimen or a coal pillar is a combination of both shear failure along the interface and compressive failure in the coal. Unstable interface failures provide a sudden de-confinement to coal rib, thus triggering uns and compressive failure in the sidewalls. The compressive failure of a coal specimen or a coal pillar can be controlled by changing its W/H ratio. As the W/H ratio increases, the ultimate strength increases. With a proper combination of interface friction and the width-to-height (W/H) ratio of pillar or coal specimen, the mode of failure will change from sudden violent failure, which is brittle failure to non-violent failure, which is ductile failure. The main objective of this paper is to determine at what W/H ratio and interface friction the mode of failure changes from violent to non-violent. In this research, coal specimens of width-to-height ratio ranging from 1 to 10 were uniaxially tested under two interface frictions of 0.10 and 0.25. The results are presented and discussed.INTRODUCTIONCoal mine bumps are sudden, violent bursts of coal from a pillar or pillars or a block of coal, resulting in a section, the whole pillar, or the solid block of coal being thrown into an open entry. These bursts are accompanied by very loud noises (Peng, 2008). Several case histories in mining have long described coal pillars or coal faces failing violently with an accompanying ejection of debris and broken material into the working areas of the mines (Campoli et al., 1987; Osterwald, 1962; Peperakis, 1958; Garvey et al., 2013). Because of the catastrophic nature of these sudden failures, understanding the causes of coal mine bumps is essential to create a safe underground working environment. This phenomenon has motivated many ground control researchers to conduct extensive field investigations throughout the past century. Rashed and Peng (2014) compared the mechanical properties of two kinds of coal, one from bump and the other from non-bump-prone mines. They found that coal itself does not play any significant role in coal bumps and recommended that future research should focus more on the local variation of geological conditions such as the interface friction between pillar and roof and between pillar and floor."

Jan 1, 2015

By W. Smith

The U.S. Bureau of Mines (USBM) is using laboratory and computer-based techniques to investigate the post- failure behavior of yielding pillars and pillar reinforcement techniques to control entry deformation. Poorly dimensioned yield pillars, can cause adverse ground conditions. Laboratory studies to evaluate various reinforcement techniques for controlling yield pillar deformation were conducted. A cracking and crushing model is used to evaluate potential tensile and compressive failure planes within pillars of various widths to assess the degree of yielding and stress redistribution. The use of an elasto-plastic model to evaluate the effect of various reinforcement on yield pillars is also discussed. These procedures effectively account for the residual pillar strength, important in yield pillar design.

Jan 1, 1995

By Andrew P. Jarosz

The present computerized mine planning systems use CAD-like and Data Base Management System (DBMS) environments for the handling of numerical, textural, and graphical data. These two environments are usually integrated, that the data provided by the DBMS are linked to any graphical element rendered by the CAD system. The subsidence monitoring, analysis and prediction process should be integrated with the mine design process. It should allow for the assessment of impacts of mining on surface, surface utilities, and structures. It should also provide for the measures to control mining, that will create only acceptable levels of negative impacts on the surface. The common data base, and graphical capabilities of the CAD interface, may be used with great advantage for both systems. The findings of the subsidence engineering modulus should be directly incorporated into the mine design system, and vice versa. In this paper the author suggests guidelines for the development of the comprehensive computer system, able not only to predict the vertical and horizontal components of the ground movement, but also assess the induced surface damages, and costs related to subsidence prevention and compensation.

Jan 1, 1995

By Luis E. Vallejo

The strength measured by the uniaxial compression test is a parameter that is widely used for the engineering classification of rocks. Sedimentary rocks such as shales, however, are difficult to evaluate by uniaxial compression tatting because the rocks slake during the preparation of the standard samples required for the tests. Indirect methods such as the point load test have been proposed to determine the unconfined compressive strength of shales and other soft rocks. It is current practice to use 24 as the conversion factor between the point load strength, Is, and the unconfined compressive strength, sf (sf = 24 Is). The present study investigated index-to-strength conversion factors for shales and sandstones obtained from surface coal mining sites in the Appalachian region. Regression analyses indicate that a conversion factor of 12.5 best correlated the strengths obtained from the point load and unconfined compression tarts in the case of shales. For the sandstones, a value of 17.4 best correlated the strengths.

Jan 1, 1989

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .0, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

Jan 1, 1999

By Soheil Bahrampour

Void detection and identification of bed separation while drilling holes in rocks for roof bolting can be a great source of information for the evaluation of ground conditions and adjustment of ground control or support measures. This can be accomplished through the monitoring and analysis of drilling parameters by the roof bolter. This paper reviews work currently under way in a joint study between Penn State University and J. H. Fletcher & Co. The detection of voids, along with identification of rock types, can lead to development of 3D roof maps, which can subsequently be used to evaluate ground support and its suitability for given ground conditions in tunneling and mining operations. Existing algorithms for void detection utilize the sensory information of the drill unit, such as feed and rotary pressure, revolutions per minute (RPM), and penetration rate, to detect voids or joints on the roof/ ribs. While the void detection algorithms are being revised to allow analysis of available data from the existing sensory systems of the roofbolters with higher accuracy and lower number of false detections, additional sensors have been added to the drill to improve its ability for accurate detection of the voids and joints. This includes installation of vibration and acoustic sensors on a drilling unit at J. H. Fletcher & Co., and pertinent data analysis which are discussed in this paper. Initial results indicate that the data obtained by vibration and acoustic sensors at high sampling rates can be used to improve the performance of the void detection algorithms independently, and when combined with the modified algorithms using existing sensors, it can substantially improve the capabilities of current void detection system.

Jan 1, 2013

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989