Search Documents

By Andre Cezar Zingano

"The objective of this paper is to estimate the coal seam strength and the pillar safety factor for low coal seams using back analysis and rock mass characterization. The coal seam strength is very important to estimate both pillar capacity and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the boreholes cores; and (ii) by back analysis from pillars successes and failures, or some in-situ tests. For low coal seams (1.2 m, or 47 in.), the confinement of the center of the pillar is very important to defining global pillar strength because the low seam height increases the confinement of the pillar core, even in small pillars. We used in this case study one underground coal mine in the Parana State where the coal seam thickness is 0.8m the pillar height is 1.3m, the entry width is 5m and seam depth is 130m. A panel test was prepared to study the pillar behavior for use of the retreat mining method. The designed pillar size was 6x5m and 1.3m high with a predicted safety factor of 1.0 based on the Hoek and Brown failure criterion is 5.3 MPa. Once no pillar failure was observed, the pillar safety factor was assumed at 1.0 and the coal seam strength was backcalculated. The back analysis estimated the coal seam strength to be 6.2MPa. The confinement of the pillar center directly affects the coal pillar strength, and also the coal seam strength estimated by back calculation.IntroductionThe coal seam strength is very important to estimating pillar strength and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the coal seam using borehole cores; and (ii) by back analysis from pillar successes and failures, or some in-situ tests like panel test or ultimate pillar capacity (Salamon and Munro, 1967; Maleki, 1981; Peng and Dutta, 1992). For the first approach, lab tests (mainly triaxial tests) and borehole geomechanics descriptions (quality and quantity of the discontinuities) determine the coal seam strength by the Hoek and Brown failure criterion (Hoek and Brown, 1997). For the second approach, a panel test to study the pillar behavior can be built to define coal seam strength by back calculation. The safety factor for the pillars in the test is 1.0, based on the estimated coal strength from the geomechanics characterization. In this case, the probability of failure is 50%. If some pillar failure occurred, and the real pillar size was measured, the back analysis could be applied to define pillar strength and the coal seam strength."

Jan 1, 2015

By Robert C. Speck

Floor heave or deformation of the mine floor into the mine opening is a problem which has plagued coal mines in this country and others. In mining areas where room and pillar mining is practiced, floor heave generally occurs when the stress applied to the floor material by a coal pillar exceeds the bearing capacity of the floor strata. When the floor strata beneath the coal pillar fail, the pillar moves downward and displaces the material under it. This material, in turn, moves outward and upward into the mine opening (Figure 1). As the underlying materials fail, the load supported by the coal pillar may be transferred to adjacent pillars. If these are marginally stable, they too may become overloaded and push into the floor. Thus, floor heave can spread through a large portion of the mine in a progressive manner. As the pillars push into the floor, differential movement and flexure of the roof strata may cause them to weaken and fail, resulting in subsidence of the ground surface above the mine. This paper describes the problem as it was manifested in the Zeigler Coal Company No. 5 and Murdock room and pillar coal mines near Murdock, Illinois, and reports the results of a U. S. Bureau of Mines- sponsored study conducted by the University of Missouri-Rolla. During the course of the study, floor heave in the two mines hindered the transportation of men, machines, and coal to and from the working mine-face, interrupted ventilation plans, drastically increased roadway maintenance costs, intensified safety and strata control problems, destroyed large pieces of equipment, and, several times, pre- vented access to otherwise minable coal resources. The ultimate objective of the study was to develop one or more simple procedures to allow detection of a potential floor heave problem during the exploration phase of mine design--before initiation of production mining.

Jan 1, 1981

Case study data were analyzed to develop and quantify empirical stress transfer relationships between seams for both longwall and room and pillar mines. Layering in the innerburden and the distance between seams were determined to be the controlling factors. To evaluate the effect of bedding planes on stress transfer, laboratory studies were conducted using layered, low modulus gravity loaded photoelastic models. Parameters investigated were thickness, number of discrete layers, modulus and friction between layers. Results showed that there was significant distortion of the pressure bulb in highly laminated conditions which correlated with the results of empirical analysis. Relationships developed were used to modify the results obtained from numerical modelling between multi-seam longwall operations. Research conclusions were demonstrated using case studies.

Jan 1, 1995

By Dezhong Kong, Jaichen Wang, Shengli Yang

"The stability control of longwall coal face is the key technology of large-cutting-height mining method. Therefore, a systematic study of the factors that affect coal face stability and its control technology is required in the development of large-cutting-height mining method in China. After the practical field observation and years of study, it was found that the more than 95% of failure in coal face are shear failure. The shear failure analysis model of coal face has been established, that can perform systematic study among factors such as mining height, coal mass strength, roof load, support resistance, and face flipper protecting plate horizontal force. Meanwhile, sensitivity analysis of factors influencing coal face stability showed that improving support capacity, cohesion of coal mass and decreasing roof load of coal face are the key to improve coal face stability. Numerical simulation of the factors affecting coal face stability has been performed using UDEC software and the results are consistent with the theoretical analysis. The coal face reinforcement technology of largecutting- height mining method using the grouting combined with coir rope is presented. Laboratory tests have been carried out to verify its reinforcement effect and practical application has been implemented in several coal mines with good results. It has now become the main technology to reduce longwall coal face failure of large-cutting-height mining method.INTRODUCTIONLarge-cutting-height mining method of more than 3.5m mining height, is one of the main methods for thick-seam mining in China. Currently, the largest mining height is 7.3m and the support capacity is 1,800mt. Shendong and Jincheng mining area have the best use of large-cutting-height mining technology (Wang, 2009). Generally, the mining height ranges from 6.5m to 7m and the support capacity ranges from 1,000mt to 2,000mt, annual output of the panel is between 10 and 12 million tons and the highest are 15 million tons. The main goal of large-cutting-height mining technology is to achieve high yield and high efficiency by increasing the advancing speed of longwall face (Yuan, 2011- 2012). However, in certain geologic conditions, rib spalling and roof falls in the unsupported area often occur. Because of the large tonnage of large-cutting-height mining equipment, once the rib spalling and roof falls cause the equipment to be out of alignment, the face advancing speed could be affected seriously that in turn affects the output (Yang, 2012). Therefore, studying the failure mechanism and control technique of coal face in large-cuttingheight mining method is of great significance."

Jan 1, 2015

By Taghi Sherizadeh, Pinnaduwa H. S. W. Kulatilake

"This paper examines the effect of different geological and mining factors on roof stability in underground coal mines by combining the field observations, laboratory testing, and numerical modeling. Observations at an underground coal mine that uses the room-and-pillar mining method showed several failures of the immediate roof, and is used as a case study. Three-dimensional distinct element analyses were performed to study the intrinsic roof failure mechanisms and to evaluate specifically the effect of in-situ stress magnitudes and directions, discontinuity mechanical properties, and variation of pillar to room size on roof stability.INTRODUCTIONThe lithology of the immediate roof with respect to the underground openings plays an important role in stability of the roof in underground excavations. Laminated, or thinly bedded shale, is one of the most frequently seen overlaying strata above the coal deposits. The bedding planes and interfaces have very low or close to zero tensile strength in the direction perpendicular to the bedding planes, and their shear strength is much lower than of the rock layers. As a result, the bedding planes are much weaker than the rock layers. Therefore, due to the stress concentrations caused by excavations, slippage and separation can easily happen along the bedding planes before initiation of failure within the rock layers.In the past, several attempts have been made to understand the mechanism behind the roof failure in underground coal mines. Most of these earlier attempts were based on empirical techniques and continuum based numerical methods that have limited capability in simulating the response of discontinuum rock mass behavior to excavation. Different factors such as the magnitude and direction of the horizontal in-situ stresses, type and mechanical properties of roof rock, surface topography, geological anomalies, gas pressure, slippage and separation of bedding planes at the roof and floor, entry width and excavation sequences are identified as key factors that could significantly impact the stability of the roof. Among all the aforementioned factors, in spite of its importance, the impact of slip and separation of bedding planes on roof stability has not received enough attention from researchers. In a few available numerical modeling studies, the bedding planes are modeled using the continuum based numerical codes such as ABAQUS (Chen, 1999) and FLAC3D (Ray, 2009). However, since the bedding planes among the roof layers become discontinuous during the numerical analysis, this behavior is most likely not be accurately captured by the continuum based numerical models. Chen (1999) conducted finite element analysis to study the impacts of the roof and coal interface slip and the bedding planes slip in the roof on the stress distribution in the roof strata by using the finite element analysis software named ABAQUS. To avoid the complications associated with the finite sliding between two deformable bodies, he limited his study to the two-dimensional finite element analysis (plane strain). He concluded that the slip and separation of interfaces and bedding planes have significant impact on the behavior of the roof strata and without considering the interfaces, the roof bolt functions cannot be simulated properly by using the numerical analysis methods. Gadde and Peng (2005) performed three-dimensional finite difference analysis using FLAC3D software with strain softening material behavior to simulate the cutter roof in an underground coal mine. Their numerical model was fully continuum and no bedding plane was included in the model. They suggested that the strain softening material model can help to simulate the cutter roof failure up to a satisfactory level (Gadde and Peng, 2005))."

Jan 1, 2015

By R. Quentin Eades, Kyle Perry

"Surface mines continue to implement highwalls for several reasons, such as increasing recovery, improving margins, and justifying higher stripping ratios. Highwall stability is a complex issue that is dependent upon a variety of mining and geologic factors, and a safe design is necessary for a successful surface operation. To improve highwall stability, it is important to understand the connection between local geology and blasting.Explosives are employed throughout the mining industry for primary rock breakage. There are a number of controlled blasting techniques that can be implemented to improve highwall stability. These include line drilling, smooth wall blasting, trim blasting, buffer blasting, air decking, and presplitting. Each of these techniques have associated advantages and disadvantages. Understanding local geology is necessary for selecting the appropriate controlled blasting technique. Furthermore, understanding the limitations and conditions for successful implementation of each technique is necessary. A discussion of the impact of geologic conditions on highwall stability is provided. Additionally, discussion is provided for the successful incorporation of the controlled blasting techniques listed above, and the associated mining and geologic factors that influence the selection and design of controlled blasting plans. Finally, a new methodology is proposed.INTRODUCTIONExplosives are used throughout the mining industry as the standard for primary rock breakage, a critical part of the mining cycle. In 2015, the U.S.. consumed 2.2 million tons of explosives (Apodaca, 2015). The coal mining industry accounted for the majority of explosive consumption, accounting for approximately 63% of total explosives. The quarrying and nonmetal mining industries accounted for 12% of explosive consumption, and the metal mining industry accounted for 9% (Apodaca, 2015). This constitutes 84% of the explosives used in the U.S. However, the energy released during the detonation process is often in excess of that required to adequately fragment the surrounding rock (Jhanwar and Jethwa, 2000). This excessive energy, along with over confinement and poor blast geometry, will cause damage to the undisturbed rock mass beyond the intended boundary of the blast. This event is known as overbreak or back-break (ISEE, 2011)."

Jan 1, 2018

By Kewal K. Kohli, Stefanie Self

"Three cases of surface subsidence investigated over abandoned coal mines after flooding in one case and dcwatering in two cases are presented in this paper. Mining was conducted by the room and- pillar method at all the mines leaving stable pillars. This paper will discuss the background chain of events and the likely causes of the pillar failure resulting in surface subsidence.CASE NO.1BackgroundThe Pittsburgh scam was mined in 1960 by the room-and- pillar method, leaving pillars (Figure I) through Mine A. located in Monongalia County. West Virginia.The mining height in U1is area was 1.83 m (6 ft) with an average mining depth of 140 m (460 ft). The mining recovery was 62% and the safety factor of the pillars was calculated at 1.15 using the Bieniawski ( 1984) fom1ula. For stable pillar design. a 1.5 safety factor is recommended. A 1.15 safety factor is considered marginal. Pumping continued after the mine was shut down in 1960 to prevent water seeping into an adjoining mine owned by the same company. The pumping ceased on December 12. 2003, and the mine was allowed to flood. The water level rose about 17 m (55 ft) by August 3 1, 2004, based on observations in a nearby borehole. On September 3, 2004 surface subsidence occurred above this area causing damage 10 a residence (Figure 2).Summary of InvestigationThe floor of the Pittsburgh coal scam played a strong role in the pillar failure. In this area, the immediate floor of the Pittsburgh seam consists of about two feet of fireclay. Extensive damage to the surface house was an indication that a major collapse below the surface had occurred. The pillars supporting the overlying strata were evaluated to find the cause of their failure. The pillars in the Pittsburgh seam (sec Figure I) had a marginal safety factor of 1.15 before flooding and were stable for 26 years. Once the mine was flooded the water level in the Pittsburgh seam rose by 17 m (55 ft). Shortly thereafter the fireclay in the floor weakened, resulting in several pillars punching into the floor unevenly making the immediate roof unstable. The overburden strata supported by these pillars also subsided do"" n into the mine, causing damage to several house on the surface."

Jan 1, 2010

By Peng Zhang

In a recent research effort, a laminated overburden loading model (as implemented in LaModel3.0 was compared with the results of ARMPS 2010, and the laminated overburden model was found to more accurately classify a ARMPS database of 52 deep cover case histories by a factor of 60% versus 54%. However, the LaModel analysis of each case study required several days to complete, as compared to a requirement of only several minutes for each ARMPS analysis. In the research presented in this paper, a computer code (ARMPS-LAM) has been developed to effectively implement the laminated overburden model into the ARMPS program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition and then automatically develops, runs, and analyzes a full LaModel analysis of the mining geometry to output the stability factor on the Active Mining Zone(AMZ), all without further user input. The present laboratory version of ARMPS-LAM can be run in batch mode; therefore, the ARMPS 2010 database of 645case histories can be analyzed very quickly. In an initial logistic regression analysis of this database, the ARMPS-LAM program was seen to be slightly more accurate than ARMPS 2010 by a factor of 71% versus 63%.

Jan 1, 2013

By C. C. White

Much benefit can be achieved by a mining company and a manufacturer if both parties can communicate effectively with each other and assist in product development; mutually beneficial ideas and products will develop. This communication can best be achieved if both parties have the opportunity of having on their respective staffs, specialists whose function is to improve the use of products used in mine development. Although a great wealth of roof control knowledge has long existed among mine operators, until recently there was not an abundance of joint development of roof control material by manufacturers and mine operators. This was perhaps due, in past lean years, to the preoccupation of mine management with other overwhelming problems that arise in mining. Manage¬ment had little time for the lengthy process of product development. Until recently, only a few of the largest mining companies had fulltime personnel devoted to roof control. A bolt manufacturer who is invited to work with an operator's roof control people in developing new material is lucky indeed in that he learns what is wanted and he acquires the benefit of the operator's knowledge and experience. He has only to come up with a satisfactory product at an acceptable price - which is not always easy: The development of new products is usually costly and time consuming, and many new products fall by the wayside. In the case of point anchors, however, this product is here to stay. The advantage of point anchors over mechanical anchors is now a proven fact. This advantage is due to less bleed off and higher ultimate load capacity of the resin point anchors. Point anchored bolts have proven to be superior to fully grouted bolts in many areas. We at Birmingham Bolt Company are fortunate in that we have been involved in joint efforts to develop point anchors with several coal companies from whom excellent advice and direction was received. It is appropriate to mention before continuing that the use of point anchors began in the 1960's in Europe and became widespread only recently in the United States. They fall in two categories, point anchors and combination point anchors. These categories have been defined by the Bureau of Mines as follows: (1) point anchors having 24" of grouted length and (2) combination anchors having 24" or more of grouted length. In the present nomenclature, all are anchored with resin or some sort of cementing compound between the rebar or tensioned element and the wall of the hole. The latest development includes an expansion shell as well as rebar, the purpose of the expansion shell being to facilitate installation without the delay necessary in use of types that require a waiting periond for setting of the resin before tightening. (See figures #1 and #2.

Jan 1, 1982

By Houquan Zhang, Yu Wu, Yanlong Chen, Zhenfu Luo, Aihong Lu

"A non-destructive detection scheme for bolt installation quality was designed by adopting the method of non-destructive detection on bolt installation quality. Based on the field measurements, a random non-destructive detection method for determining the characteristic length including anchoring length, free segment length and initial axial load of bolt was discussed, and the characteristics of increasing bolt axial load in the initial stable stage was obtained. The results show that the bolt axial load and deformation of surrounding rocks correlate each other. Compared with the traditional detection technique for bolt installation quality, the non-destructive detection method has obvious advantages such as random, accuracy, and economic. The method provides a reliable basis for bolt support optimization and stability control of surrounding rocks.INTRODUCTIONBolt support in roadway can make the surrounding rocks and bolt form a structure in the early stage of roadway development through the bolt pre-tension, which can maximize the self-bearing capacity of surrounding rocks. Thus it is a form of active support (Kang, 2007). In order to make the bolt play an active supporting role, it needs to ensure the installation quality of bolting. Thus the bolts can supply a high initial anchoring force and control the deformation of surrounding rocks (Shan, 2009; Wei, 2012). Moreover, bolt supporting is a concealed work. Once installation quality problems appear; it will be difficult for effective detection and screening (Xie, 2008).THE PROBLEMS OF BOLT INSTALLATION QUALITY IN COAL MINE AND ITS DETECTIONThe Problems of the In Situ Bolt InstallationDue to the problems in installation environment, machine, and technique, and workers proficiency (Li, 2003), there are many problems exist in bolt installation. If the borehole depth is too long, the anchoring agent will accumulate at the bottom of the bore, which reduces the anchoring length. Furthermore, if the borehole depth is short due to the poor geological condition, the exposed part of the bolt will be too Jong and the pallet cannot cling to the rock face, which prevent the pre-tension from being applied. The pre-tension is very important for bolt installation. If pre-tension is insufficient the rock bolt cannot control the deformation of surrounding rock efficiently and the bolt anchoring force will decrease considerably. The bolt length is another important parameter for anchoring quality, which will affect the control area of bolt supporting. In addition, the cleanness of drill hole has a great influence on the effective anchorage length of bolt. If the drill hole cleaning is not enough, it will directly affect the anchoring agent and the contact area of surrounding rocks, which will decrease the effective anchorage length and initial anchor-force."

Jan 1, 2016

By J. Nielen van der Merwe

During the process of pillar extraction at the Welgedacht Colliery, an unexpected pillar collapse resulted in the entrapment of equipment. The area was visited soon after the event to evaluate the stability of the area for the purposes of extracting the equipment. It was found that the area had stabilised sufficiently to allow work without undue risk to the safety of workers. The equipment was reclaimed successfully. A subsequent investigation into the reasons for the collapse was conducted. It entailed detailed underground and surface subsidence observations and numerical modeling. It was found that none of the perceived negative factors that were present at the time could result in pillar loads that were sufficient to cause the collapse. It was concluded that the local pillar strengths were less than the nationally used value and that they were possibly further reduced by aging.

Jan 1, 1999

By Marc Arl

Failures of the face and roof above longwall shields have caused days and sometimes weeks of lost production. A common recovery method for these failures has been to pump light weight cementitious grout into the roof and face cavity to stabilize the area This approach while effective is very time consuming and costly. Mines in several coal producing nations have over the past few years been applying phenolic foam grouts in these situations in lieu of cementitious materials. Phenolic foam is a two-component injection product intended for cavity filling, air and gas sealing and the consolidation of highly fractured strata. The properties of phenolic foam; rapid application, quick setting, high expansion rate, high compressive strength and excellent anti-static properties, produce a fast, safe and cost effective cavity filing solution. The product is also classified as fire resistant and so is also suitable for sealing off underground heatings and for aiding fire fighting operations in deep mines. This paper will discuss the application and use of phenolic foam in various underground coal mines in the world over the past few years.

Jan 1, 2005

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By C. P. Mangelsdorf

The success of the Birmingham roof truss (Figure 1) in supporting some difficult roof conditions, particularly in the Illinois coal basin, has given impetus to the development of a number of alternate schemes. These schemes attempt to alleviate two major problems with the Birming-ham truss, namely, the time required for installation and the cost of material. Because of the difficulty of drilling angled holes and the number of different pieces of hardware which must be handled manually, most operators have been unable to install Birmingham trusses in the cycle and have had to schedule truss crews during the maintenance shift or whenever they would not impede production. Due to this delay the truss has traditionally been viewed as a supplemental form of roof support. In fact, the truss might qualify as primary support and replace at least two bolts if it could he installed in the cycle (and MSHA would accept it as an alternate in the roof plan.) [ ] Figure 1. The Birmingham truss. Two attempts to deal with the first difficulty have sought to streamline the truss hardware while preserving the essential character of the Birmingham truss. One of these, by Peabody Coal, is reported elsewhere in these proceedings by C. Bollier. Another is a contract issued by the Bureau of Mines to Bendix Corporation for the development of a machine, particularly suited for use in low coal, which will automate many of the operations currently executed manually. This machine is expected to be ready for field testing by fall of 1982. Once in place, a truss installed by either of these schemes will interact with the roof in the same way as a conventional Birmingham truss. An alternate approach has been proposed by several different manufacturers independently. Although the hardware details differ. the essential idea consists of two angle bolts, the heads of which are connected by a horizontal chord tightened to some pre-determined tension. Figure 2 shows the generalized concept and does not depict any one of the four systems proposed. The advantage of this scheme is that the angle bolts can be installed and tightened in the cycle, and as bolts, immediately satisfy the roof control plan. The horizontal chord can be added later to achieve almost any initial desired roof loading, the limits of which are defined below this scheme is referred to here as the angle-bolt truss. Because of a fundamental difference in the way in which load is transferred between chords, this design does not interact with the roof under subsequent loading in the same manner as a Birmingham truss. The purpose of this paper is to examine this fundamental difference and its consequences. [ ]

Jan 1, 1982

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By Michael J. Peacock

The Powhatan No. 4 Mine is located in southeastern Ohio along the Ohio River in Monroe County. The mine produces approximately 3.2 million tons of steam coal annually from the Pittsburgh No. 8 seam. The Pittsburgh No. 8 seam in this area dips to the southeast in varying amounts from 10-feet to 40-feet per mile. The seam is made up of a main bench coal (4' to 5f' ) containing several thin and variable partings and a rider ("roof") coal (0" to 18") which is separated from the main bench by a parting (0" to 18") that is reasonably consistent in occurrence and position. Strata overlying the seam varies from a bedded to nonbedded calcareous mudstone-claystone (6' to 12') in the north and east regions of the mine to a sandstone (Pittsburgh Sandstone C10' to 40'1 in the south and west regions. The Redstone Limestone (10' to 18' ) overlying the mudstone-claystone in the north and east thins and rises toward the area of sandstone deposition in the south and west. From its opening in April of 1971 until late 1981, primary roof support in the long-1 ived entries at Quarto Mining Company's Powhatan No. 4 Mine had been achieved with 8-foot and 10-foot. 518-inch mechanical roof bolts using a Single expansion shell. These bolts were installed so that the expansion shell achieved a competent anchorage in the limestone. However, as the mine developed westward, the limestone began to trend upward becoming inaccessible as an anchorage medium at the 8-foot and 10-foot horizons. Anchorage achieved in the underlying mudstone-claystone strata was failure-prone due to weathering (after exposure to air and moisture) and inconsistencies in the anchorage horizon, leading to an increase in the incidence of reportable roof falls at the mine. Responding to the threat to safety and productivity posed by the increase in roof falls. Mine Management through its Safety and Engineering Departments, sought solutions to the problem. In seeking a solution to the problem, the safest and en engineering groups examined the reportable roof falls to determine the cause of those failures. Their examination pinpointed two items which were found to be a common link in the majority of those falls; namely, anchor integrity and geologic trends. Analysis of the roof falls indicated that due to effects of air and moisture on the anchoraae zones in the mudstones and clay- itones, the integrity of the anchorage over time could not be maintained. Geologic trends noted included the upward trend of the -main limestone as mining progressed westward, inconsistencies in the amount of roof coal and draw slate in the immediate mine roof and increasing evidence of heavily slickensided immediate mine roof. In the absence of the protective barrier provided by the roof coal, the immediate strata and particularly the draw slate, is susceptible to deterioration due to the weathering effects of air and moisture and thus is prone to "eat out" around the roof bolts and cause roof falls. The presence of heavily slickensided roof creates a need for increased contact surface such as that provided by plank and header blocks to aid in holding up the roof and tends to make the behavior of such roof very unpredictable. Having determined the causes of the roof falls. Mine Management began to identify the kind of roof support which would best solve these problems, while at the same time providing the mine with a safe, cost effective and efficient roof support system. This paper will provide an analysis of how this decision was reached, the background that was researched to aid in forming the decision, the considerations that played key roles in the formulation of the plan, the mechanics of following through and implementing the new roof support system, and an assessment of the resultant gains in safety, productivity and improved costs derived from the implementation of the new roof support system.

Jan 1, 1986

By Yingzin Zhou

Partial backfilling can be used to reduce and control surface subsidence damage caused by longwall mining or pillaring operations in room-and-pillar mines. The use of partial backfill as opposed to total backfill minimizes the cost associated with such efforts. By com- paring surface subsidence, strains, and slopes, the effectiveness of partial backfilling including the amount, geometry, and location of backfill are demonstrated. Results show that it is possible to arrange a given volume of backfill in its geometry and location so that optimum effects are achieved in controlling vertical movement, surface slope, and curvature.

Jan 1, 1990

By Jessica M. Wempen

Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has been demonstrated as a potentially practical method for measuring mining induced surface subsidence. Unlike traditional methods of subsidence monitoring, DInSAR has the capacity to generate subsidence data on a regional mining scale with a relatively high data density. Using DInSAR to evaluate subsidence over large regions with relatively long time scales has the potential to help quantify the impact of subsidence in the mining region, and provide a means for validating whole-mine geotechnical models. In this study, nine pairs of interferometric data from the Japanese Advance Land Observing Satellite (ALOS) were processed using DInSAR to generate displacement maps for a group of trona mines in southwest Wyoming. The data cover a time span from December 2007 to March 2011. The maximum subsidence for one of the mines totaled 1.3 meters for this period. Cumulative DInSAR displacement maps show the development of subsidence over time. In this mining region, surface subsidence is generated primarily by extraction of trona using retreating longwalls. Additionally, trona is extracted by solution mining, which also generates measurable surface subsidence.

Jan 1, 2014

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By Peng Zhang

In previous research, the laminated overburden model from the LaModel program was effectively integrated with Analysis of Retreat Mining Pillar Stability (ARMPS) through ARMPS-like input to create a laboratory version of the new ?ARMPS-LAM? program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition, and then automatically develops, grids, runs, and analyzes a full LaModel analysis of the mining geometry to output the section stability factor (SF), all without further user input. The initial ARMPS-LAM results were encouraging with a case history classification accuracy of 55% to 71%; however, a few of the input variables that were nominally included in the SF calculation showed independent significance in the classification accuracy. Therefore, in order to further improve the accuracy of the ARMPS-LAM program, an investigation of the SFs calculated by the new ARMPS-LAM program and the ARMPS program is detailed in this paper. The initial results of a linear correlation between the ARMPS-LAM SF and the ARMPS SF showed a strong correlation (R2 = 0.88), with the ARMPS-LAM SF averaging about 8% higher. The difference in SFs between the programs were further investigated, and, ultimately, the results indicated that the laminated overburden model as implemented in ARMPS-LAM distributes relatively more load on the section pillars for depths less than about 1,000 ft and less load for depths more than 1,000 ft. The results of this research highlight the potential for improving the ARMPS-LAM program in the future by implementing a more accurate loading calculation on the section pillars.

Jan 1, 2014