Search Documents

By Rudolf Keller

In the electrolysis of neodymium oxide from a molten fluoride electrolyte, anode effects may occur at the carbon anodes, interfering with smooth cell operation. In laboratory experiments, we attempted to circumvent this problem by selecting electrolytes with a high oxide concentration, possibly at relatively low rare earth content, but cathodic deposition was not satisfactory. A regime at higher cell voltage was discovered to yield good cell performance, but evolution of considerable amounts of fluorocarbon compounds suggested that a reactive treatment of the off-gases would be necessary for environmental acceptability. Subsequent experimentation at low cell voltage revealed conditions for satisfactory operation without occurrence of anode effects and without formation of any CF4 or C2F8.

Jan 1, 1997

By Edouard Asselin, Guikuan Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe( II )-Fe(III)-H2S04 solution at 25°C and 70 °C. Results from the calculation ofspeciation in the above solution reveal that, at both 25 °C and 70 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller values for the reversible potential of the ferric/ferrous couple based on the Nemst equation. Exchange current densities of the ferric/ferrous couple were obtained by extrapolating the cathodic linear Tafel line to the reversible potential and are on the order of 10-7·10-6 A/cm2 at 25°C and 10·6-10-5 A/cm2 at 70 °C, respectively. The transfer coefficients were about 0.35-0.38 at 25°C and 0.35-0.45 at 70 °C. Polarization plots of CPC and CPP under different nominal Fe3+/Fe2+ ratios are in good agreement at 25 ·c and at 70 °C. Based on the obtained exchange current densities, the rate constant k, was calculated and is on the order of 10-1 cm/s at 25 °C and 10 1 cm/s at 70 °C.IntroductionChalcopyrite is the most abundant copper mineral in nature, accounting for about 70% of copper reserves in the world [I]. In recent years, the metallurgical industry has been searching for a hydrometallurgical process as an alternative to pyrometallurgical treatment due to high emissions of S02 and capital costs associated with smelting. Activity in this area has increased recently due to some inherent advantages associated with hydrometallurgical processing, such as the possibility of treating low-grade ores (increasingly more abundant in the case of copper) and easier control of waste, with the attendant benefits to the environment [I]. Chalcopyrite is highly refractory under most hydrometallurgical conditions, owing to the formation of an anodic passivation layer on the chalcopyrite surface which renders the process kinetics very slow. Most of the currently proposed processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Sulfuric acid is preferred over all other leaching reagents in terms of cost, environmental friendliness, and ease of its regeneration during electro-winning. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale,"

Jan 1, 2012

By S. N. Ojha, Gouthama, R. K. Mandal

"Spray deposition processing of liquid immiscible alloys, based on AI-Pb and Cu-Pb systems have been investigated. Process variables have been optimized to generate uniform dispersion of ultrafine second phase particles in· the matrix of the primary phase. Mechanisms governing the microstructural evolution in this synthesis methodology are discussed. Results of the present investigation are used to demonstrate that rapid solidification of atomized droplets initially provides a high nucleation rate of the second phase during the liquid phase separation. The solid matrix phase nucleates at a later stage and grows with a high velocity enabling trapping of the dispersed phase. Subsequent alteration in the size and size distribution of the second phase is suggested to arise further during deposition of high velocity droplets. Possible reasons for this effect are brought out. Microstructural features of atomized powders and spray-deposits of these alloys are presented to support the present approach of synthesizing composites. IntroductionIn recent years, synthesis of advanced materials with metastable microstructures and ultra fine dispersion of second phase particles has led to the development of novel techniques of materials processing. The other requirement of such a processing methodology is to achieve near-net shape geometries in less number of processing steps. The solidification processing method via spray deposition route qualifies these criteria. This process primarily involves atomization of a melt by high energy gas jets into spray of droplets which are subsequently propelled by the kinetic energy of the gas towards a deposition substrate to build-up a thick high density preform. Although the concept of spray deposition was pioneered by Singer [1] in the early seventies, the fundamentals of the deposition process has been understood only recently [2-4]. Several benefits of spray deposition processing are by now well established [5,6]. Rapid solidification effects are inherent in spray deposition processing due to high heat exchange rate at the droplet-gas interface and also on the deposition surface by force convection. Since considerable heat extraction occurs from the atomized spray prior to droplet consolidation, a relatively low processing temperature is ensured in this process. As a result deleterious coarsening phenomenon can be minimized. In addition, controlled maneuvering of the substrate provides the capability of the process in producing disc, sheet or tube shape preforms of difficult to work materials in a single operation. A significant improvement in properties, resulting from microstructural homogeneity and refinement in grain size induced by spray deposition has been reported for several alloy systems [7,8]."

Jan 1, 1994

By M. M. Kim

As-electrogalvanized coatings of pure Zn, Zn-11% Fe, and Zn-18% Fe coatings were characterized in terms of initial crystal structure and surface morphology. Samples were then subjected to heat treatments simulating the paint bake cycle of automobile manufacturers. Surface morphology changes were correlated with the process variables, and crystallo.graphic changes were interpreted by mapping heat treatment routes on the Fe-Zn phase diagram. The morphology of pure zinc electrogalvanized coatings with heat treatment from platelets to smeared platelets. The zn-11% Fe coating changes with heat treatment from tetrahedral nodules to a mixture of round and tetrahedral nodules, with the Zn-:18% Fe coating always having round nodules. Regarding crystal structure, a critical transformation time can be defined at any selected temperature, below which the crystal structure does not change. This temperature is related to iron content.

Jan 1, 1990

By K. Tozwa

The electrical conductivity of electrolytes for copper electrorefining and electrowinning processes has been reported by many researchers since 1911. The experimental results show that the conductivity increases with an increase in sulfuric acid concentration and decreascs with an increase in copper concentration. In pure copper sulfate solution, however, the conductivity increases with an increase in the copper concentration. After confirming the conductivity of pure and acidified copper sulfate solutions experimentally, the concentrations of hydrogen ion and free (not hydrated) water in the electrolytes were estimated and it was found that the relation between the conductivity of acidified copper sulfate electrolytes and the products of concentration of hydrogen ion and free water is linear. Accordingly, the conductivity of acidified copper sulfate electrolytes increases with an increase in sulfuric acid concentration and decreases with an increase in copper concentration.

Jan 1, 2003

By C. Damiani

The Chuquicamata smelter, operating since 1952, has gone through several developing stages which have been characterized by the addition of peak technology for copper concentrate smelting (Teniente converter and Outokumpu flash furnace) with an intensive use of technical oxygen, which has permit-ted to partially discontinue the reverberatory furnace utilization. This paper shows the main indicators and operational practices at present, as well as those concerning maintenance aspects. Finally, the most relevant topics related to the future development of the smelter are mentioned with special remarks on the Decontamination Plan, which allows US to keep the high level of production, reducing the emission of contaminants according to the legal requirements in force.

Jan 1, 1993

By Ximeng Zhu

The electrochemical behavior of mineral and coal pyrites in stirred and quiescent alkaline boratelsulfate solutions @H 7.9-10.5) have been investigated using cyclic voltammetry. Significant differences in the electrochemical response of these pyrites were observed. At the mineral pyrite surface, three anodic peaks at about -0.8 V, -0.1 V and +0.5 V (SCE) have been detected along with their corresponding reduction peaks. The first two peaks correspond to FeIFeOI) and FeOI)lFe(III) oxidation. The third peak is present for quiescent conditions but disappears as a distinct peak when the electrolyte is stirred. In the upper voltage region +0.30V (SCE), the current increases markedly during stirring and the reactions correspond to the oxidation of pyrite with the formation FeOII) oxides plus elemental sulfur. Also there is evidence that Fe oxy-ions form. Coal pyrites, under rapid sweep conditions display only the first two anodic peaks, the associated reduction peaks and an additional reduction peak corresponding to one or more of the high voltage oxidation products. After prolonged exposure to high potentials, coal pyrite displays reactions similar to those of mineral pyrite but at much higher current densities demonstrating the much higher reactivity of the coal pyrite. The reactivity sequence was Upper Freeport coal pyrite > Pittsburgh coal pyrite > mineral pyrite.

Jan 1, 1991

By Yuanbo Zhang, Zhixiong You, Li Qin, Guanghui Li, Tao Jiang

Low-grade manganese oxide ore is generally characterized by high iron content. In this work, sulfidation roasting of an iron-rich manganese oxide ore with elemental sulfur was characterized. The experimental results indicated that manganese dioxide can be selectively reduced over iron oxide by using elemental sulfur. The manganese phases in roasted product included low-valence manganese oxide, manganese sulfide and manganese sulfate, while those of iron mainly depended on the sulfur addition. Iron oxide would only be reduced or sulfidized at larger sulfur additions. The effect of roasting temperature and S/Mn mole ratio on the phase transformations was also investigated; extractions of Mn/Fe by sulfuric acid were evaluated. An extraction of Mn greater than 95% was obtained while that of Fe was controlled less than 10% under the optimal conditions.

Jan 1, 2016

By J. S. Kirkaldy

A theoretical procedure is demonstrated for calculating two-dimensional binary cellular single-valued interfaces and extended to triple-valued (remelt) shapes. The numerical calculations for the single-valued local equilibrium problem which yield unique shapes as functions of the supersaturation parameter a and the partition coefficient k are reviewed. The cell amplitude L and wavelength A scale identically as the inverse velocity to the 112 power and the aspect ratio r is a constant equal to 312, independently of a and k for a < 0.5.. For 0.5 < a < m, L, A and r decrease asymptotically to zero indicating the finite amplitude nature of the instability at a = 1 and the existence of sub-marginal states which converge to a flat interface at a- m (Glv- m). Scaling comparisons between equilibrium single-valued and triple-valued and deep-rooted non- equilibrium cells are made.

Jan 1, 1992

By Masami Taguchi

"It is found that lead monoxide, PbO, has an ionic conductivity, and the all solid-state electrochemical cell using this oxide as an electrolyte has attracted the attention of battery researchers. In this study, thin film PbO2/PbO/Pb solid cells were produced on glass substrates and their discharge properties were investigated. The acti.ve material for the positive electrode, PbO2, was obtained by reactive sputtering of a Pb target in oxygen plasma. The PbO electrolyte and the active material for the negative electrode, Pb, were vacuum evaporated from /3 -PbO powder and a Pb block, respectively. The open-circuit voltage of the cell agreed with the theoretical value based on the thermodynamic data, and the close-circuit voltage was improved by the addition of a univalent impurity such as sodium or potassium to the PbO electrolyte. The connection of the cells in series and in parallel produced a higher electromotive force and a larger capacity. Also, the charge-discharge cycling test revealed that the cell could be charged and function as a storage battery.IntroductionGenerally, the ionic conductivity of a solid-state electrolyte is lower than that of a liquid electrolyte near room temperature. This has been a serious obstacle to using such electrolytes in an electrochemical cell. However, some solid-state electrolytes, which can preferentially pass a specified ion and have high ionic conductivity, have been found. Lead monoxide, PbO, which is an oxygen ion conductor, is such an example (1)(2). If a solid-state electrolyte is adopted for use in an electrochemical cell the problem associated with a liquid electrolyte such as leakage can be alleviated. The cell structure also can be simplified, because the electrolyte plays the role of separator to prevent the active materials from mixing. Thus, physical vapor deposition technology may make it possible to develop a very thin film cell, which consists of only solid phases (3)(4). In this study, the thin film PbO2/PbO/Pb solid cell with a thickness· of only a few micrometers, in which all the constituents were systematically deposited on a glass substrate by reactive sputtering and vacuum evaporation, has been produced and the charge-discharge properties were investigated. An attempt was made to improve the discharge properties by doping impurities such as Na2CO3 and Sb2O3 into the PbO electrolyte. Moreover, the connection of the cells in series and in parallel to get a higher electromotive force and a larger capacity, and the charge-discharge cycling test to determine its use as a storage battery were carried out."

Jan 1, 2000

By Dae Jin Ha

Sticking phenomenon occurring during hot rolling of two STS 430JlL ferritic stainless steels was analyzed by hot-rolling simulation tests. The sticking started from the initial nucleation stage in which the rolled materials were stuck onto the roll specimen surface, proceeded to the growth stage in which stuck fragments grew further, and reached the saturation stage. The modified 430JlL steel had a smaller number of sticking nucleation sites and slower growth rate than the conventional 430JlL steel because of higher high temperature hardness, thereby leading to less serious sticking. When the simulation test was conducted at 1070 °c, Cr oxides were formed on the surface of the rolled materials, and thus the sticking was drastically reduced because of the increased surface hardness of the rolled materials. In order to prevent the sticking, high-temperature properties of the rolled materials should be enhanced when rolled at 900°C or 1000 °C, and rolling conditions and alloying compositions, under which the oxide formation was promoted, were more important than high-temperature properties when rolled at higher temperatures than 1000 oC.

Jan 1, 2008

By K. C. Liddell, B. Dou

"In producing multilayer films for magnetic data storage applications, the interfacial roughness must be controlled in order to obtain high quality materials with reproducible properties. The present understanding of the effect of roughness on multilayer properties such as magnetoresistance is sketchy, particularly for electrodeposited films. In this study, quantitative atomic force microscopy was used to characterize surface morphology before and after Ni films of varying thickness were deposited on Cu cathodes. A multinuclear multilayer growth mechanism is supported by both the deposition conditions and the AFM images, and a multinuclear multilayer model gave a satisfactory fit to measurements of the density of peaks on ultrathin Ni films between 0 and 8 nm thick.Alloys consisting of alternating ferro-and paramagnetic layers have begun to replace Permalloy in the sensing elements of magnetic hard drives. The operating principle of the new read heads is giant magnetoresistance (GMR), and they are smaller and more sensitive than previous inductive heads (1). Experimental studies on sputtered multilayers have emphasized the role of layer thickness and interlayer roughness in determining the presence and size of the GMR effect (e.g., 2,3,4,5,6). However, roughness in electrodeposited multilayers has rarely been measured, even though read heads are likely to continue to be made by this process for some time to come. Cu/Ni can be considered a model system for understanding processing-microstructure-property relationships in electrodeposited multilayers and is the most widely investigated of all such systems (e.g., 7,8,9,10,11,12). Nevertheless, the roughness of the interfaces in Cu/Ni electrodeposits has not been systematically characterized by quantitative techniques, and in all studies reported so far, the total deposit thicknesses were considerably greater than the 10 nm needed for most sensor applications (1). The thinnest such films were about 50 nm (7)."

Jan 1, 1998

By A. Patti, S. Reutzel, D. M. Herlach, L. Ratke, I. Egry

Cu-Co shows a metastable miscibility gap in the region of the undercooled melt. Undercooling of the melt below the binodal leads to separation of the melt into a Co-rich LI-phase and a Curich L2-phase. Experimentally, undercooling into the metastable miscibility gap is realised by means of electromagnetic levitation (EML), processing in drop tube (DT) and by melt flux embedding. As undercooling is large in these experiments, the velocity of the solidification front is high and the microstructure is frozen in instantaneously. Samples have been undercooled and solidified in the TEMPUS-facility (container less electromagnetic processing under weightlessness) during parabolic flight under reduced gravity conditions. Microstructures of solidified samples have been analysed and compared to those processed under gravitational conditions. The influence of convection on phase growth is much lower in reduced gravity. The microstructure shows spherical droplets of the minority phase, statistically dispersed in the majority phase.

Jan 1, 2004

By Ma Keyi, Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping

"The oxidation of the Multifunctional Electrodeposited RE-Ni-WP- SiC Composites at high temperature is investigated. The results show that during high temperature oxidation the relationship between the mass change of pure Ni , Ni-W-P, Ni-W-P-SiC or RE-Ni-W-P-SiC coating and the oxidation time follows a mixed curve, i.e. it is approximately a linear relationship when the oxidation time is less than 60 mins while it is a power function relationship when the oxidation time is over 60 mins. The order for the oxidation rate of the four coatings is Ni> Ni-W-P> Ni-WP- SiC>RE-Ni-W-P-SiC. The mass change of Ni-W-P, Ni-W-PSiC or RE-Ni-W-P-SiC coating increases exponentially with a rise of oxidation temperature. The high temperature-oxidation resistance of RE-Ni-W-P-SiC composite coating is 3-4 times that ofNi-W-P alloy coating. The cross section morphologies and Xray diffraction patterns indicate that the high temperature oxidation resistance of RE-Ni-W-P-SiC composite coating is better than any other coatings.1. IntroductionWith the rapid development of modem industries the products in engineering industry are continually challenged by the requirements of long-term and stable working at higher temperature, pressure, speed and under adverse conditions. Consequently, the surface properties of the products, such as the resistance to oxidation at high temperature, the resistance to wear and the resistance to corrosion, should be improved continually."

Jan 1, 2000

By Hongmin Zhu, Guihua Wang, Xiangsheng Wang

"The anode process of carbon electrode in fluoride melt was studied by voltammetry and chronoamperometry. Anode gases were analyzed by gas chromatography on-line during controlled-potential electrolysis. Two peaks were observed on the cyclic voltammograms. According to the results of gas chromatography, the first peak was corresponded to the discharge of residual oxide ions, with the formation of CO and CO2. Discharge of fluoride ions occurred at 4.1 V vs. Li+/Li, and leading to the anode effect. With the occurrence of anode effect, small amount of CF4 was detected. As the potential reached 4.5 V, CF4 and C2F6 gas evolution occurred, and the current increased to form the second peak.1.IntroductionIn the primary production of Aluminum and some rare earth metals like neodymium, a departure from normal cell operation known as anode effect results in the generation of perfluorocarbons (PFCs), which have high global warming potentials [1]. Owing to the pressure of environmental protection, considerable research has been carried out to clarify the mechanism of anode effect and PFC generation of industry and laboratory cells in the aluminum electrolysis system [2-9]. The common result on PFC generation is that the PFCs are emitted from Hall-Heroult cells only when they are on anode effect. In this article, we selected LiF, the main electrolyte for the neodymium electrolysis [10-11], to perform further investigation on the underlying kinetics of PFC generation and the nature of the reactions at the electrode.2. ExperimentalAll experiments were carried out in an alumina tube reactor, which was filled with high purity helium atmosphere. Spectrographic graphite crucibles were used, which played the dual role of molten fluoride container and the counter electrode. Lithium fluoride was analytical grade. The experiments were carried out at 900 °C."

Jan 1, 2011

By Xie Gang

The leaching experiment used by bacteria on the low grade sulfide copper ore which is difficult to leach was carried out. Some leaching bacteria which have good physiological and leaching activity were isolated and domesticated, and were adapted to leaching ore. The effective domesticated method was put forward. Some technological parameters such as ore acidification, potential controlling, leaching method, ore granularity, leaching acidity, leaching liquid quantity and acid consumption were obtained by column experiment and leaching ore in situ under the ore well. The results show it could leach 30.62% of copper from the low-grade sulfide copper ore within 24 weeks by column leaching method, and the bioleaching rate of copper is 22.83% by leaching in situ under the ore well in 8 months.

Jan 1, 2006

By Kazuhiro Nisizono, Takashi Kuroki, Nobuyuki Mori, Keisaku Ogi

"The improvement of critical current density and mechanical property is essential to the practical application of the superconductive oxides. A solidification technique is developed in this study for the growth of columnar or single Y123 crystal with finely dispersed Y211 and Ag particles through a monotecto-peritectic reaction of Li.(Ba-Cu-Ag-0 rich liquid)+ Y211-+ Y123+Lz(Ag rich liquid). The large solidification rate and temperature gradient can refine the Ag and Y211 particles. But Ag-free region is widely formed along the crystal growth direction in the central part of the Y123 cell. Since this phenomenon occurs because of the cellular growth, it is necessary to narrow Y123 cell width or to grow Y123 crystal with flat freezing interface. By controlling crystal growth direction using a seed crystal, Y123 columnar or single crystal with uniformly dispersed fine Ag particles are obtained. The· behavior of Ag and Y211 particles during the solidification of Y123 crystal is simulated by the peritectic growth model of faceted Y123 crystals.IntroductionY-Ba-Cu-0 superconducting oxide (YBCO) with high critical temperature also has excellent superconducting characteristic under the high magnetic field. The critical current density (Jc) has been enhanced by ·using unidirectional-solidification technique, which can overcome the weak-link problem at grain boundaries and control the crystal orientation and the distribution of Y211 particles which give effective magnetic flux pinning centers in the Yl23 matrix [1-4].In addition to improving superconducting properties, it is necessary to improve mechanical property for the practical application. The silver addition to the melt-textured YBCO superconducting oxide has been reported as the effective method to improve mechanical properties without degrading superconducting properties. Since the material properties are considered to be largely affected by silver particle size, form, dispersion state etc. in the Y123 phase, it is important to control Ag distribution in YBCO/Ag composites. Besides, it is also reported that the silver addition improve the corrosion resistance to the water and CO2 [5,6]. Nishizono et al. [7-9] have reported that the silver distribution in the YBCO/Ag composites is largely affected by the solidification condition, but yet some unclear points are also remained. YBCO has been also fabricated by the zone melting method [10-12], and Furuya et al. [5] and Hirano et al. [13] have reported the fabrication of silver added YBCO composites, but the distribution and behavior of Ag are not investigated in detail"

Jan 1, 2000

By D. S. Barr

The Freeport McMoRan chlorination circuit is comprised of four related processes: ore chlorination, gas scrubbing, chlorine supply and excess hypochlorite removal ("hypo kill"). Each of these processes are described, and related to the pertinent mineralogic components in the carbonaceous ore feed to the plant. The chlorination system in use at Jerritt Canyon to passivate forms of preg-robbing organic carbon has proven to be a cost effective and efficient means to recover gold from low sulfide carbonaceous refractory ores, where gold may not be specifically associated with either the sulfides or the carbon.

Jan 1, 1987

By Olusegun J. Ilegbusi

"A two-fluid model is used to calculate flow and heat transfer characteristics of a plasma jet. This model accounts for both gradient-diffusion mixing and unmixing that may result from pressure-gradient-body-force imbalance in the system. The unmixedness is considered to be essentially a Rayleigh-Taylor kind instability. Separate transport equations are solved for the plasma and ambient gas velocities, temperatures and volume fractions. The two fluids allowed to exchange mass, momentum and energy through empirical interaction parameters. The empirical coefficients are first established by comparison of predictions with available experimental data for shear flows. The model is then applied to an Argon plasma jet ejecting into stagnant air. The predicted results show the significant build-up of unmixed air within the plasma gas, even relatively far downstream of the plasma torch. By adjusting the inlet condition, the model adequately reproduces the available experimental data on the temperature profile.IntroductionPlasma jets have important applications in materials processing, some of which include spray deposition, melting and refining, heat treatment and materials synthesis. In a typical reactor, the hot plasma stream entrains a surrounding gas and the resulting heat and mass transfer and the condition of operation of the torch, determines to a large extent, the performance of the unit. The entrainment may prevent uniform mixing and produce regions of unmixed hot/cold gases and non-uniform deposits as a result of insufficient melting of deposit in cold regions. This phenomenon may also affect chemical reaction rate in plasma systems for NOx reduction in exhaust gases.The study of plasma phenomena is often conveniently divided into three parts namely, the plasma torch, the plasma jet and analysis of the particles carried in the jet. The present work concerns processes occuring in the near-field of the plasma jet i.e. just downstream of the torch."

Jan 1, 1994

By Oleksandr Liaskovskiy, Sergey Beringov, Sergiy Yatsuk, Timur Vlasenko, Iryna Buchovska

"Working with solar-grade silicon for solar cells application usually meets some difficulties in comparison to polysilicon produced by Siemens method: higher impurities content leads to lower yield, worse electro-physical parameters and poor performance in solar cells application. However some adjustments in ingot production can show significant improvements in quality of final product: crystalline wafers and cells.Recent investigations have shown that solar-grade silicon is suitable for high effective production process such as mono-like multicrystalline wafer production. Production-scale lots made at Pillar show promising results for solar-grade silicon application: high-quality wafers with significantly big crystalline grains of <100> orientation.IntroductionThe standard technology of producing multicrystalline silicon ingots by directional solidification method in quartz crucibles has a number of disadvantages resulting in limited efficiency of solar cells made of multicrystalline material: crystallites of multicrystalline ingot are relatively small (down to 5 mm size), grain borders of crystallites contain parasitic impurities such as metals, silicon nitride etc., crystallographic orientation of crystallites is random. The listed deficiencies are an integral characteristic of the technology which affects the efficiency of solar cells, such as presence of solar cells with low efficiency even at a high level of average efficiency, problems with shunted cells, silicon nitride inclusions, which adversely affect cell efficiency and are centres for silicon carbide formation, impossibility of application of high effective alkaline texturing etc. Also with regard to the targets set by photovoltaic to reduce the cost per Wp in the nearest future, standard technology of multicrystalline silicon ingots production by directional solidification faces certain challenges some of which are hard to overcome due to rather low efficiency of solar cells made of multicrystalline wafers. Therefore alternative methods of multicrystalline silicon production for photovoltaic application having a number of advantages in comparison to traditional technology are developing rapidly."

Jan 1, 2012