Search Documents

By T. T. Chen, J. E. Dutrizac

"Grooved cast Pb-Ag anodes are used by some zinc refineries to improve current efficiency. It was found that the manganese oxide scale formed on a grooved Pb-0.75% Ag anode consists mainly of MnO2, which occurs characteristically in rhythmically banded colloform structures and adheres to a layer of ""Pb02+PbS04"" that oxidized from the anode. The relatively homogeneous and nearly fracture-free morphology of the ""Pb02+PbS04"" layer suggests the relatively uniform corrosion of the anode. Deposition of the Mn oxide initially follows the contours of the anode surface, but the grooves eventually become filled with Mn oxide and gypsum. Hydrous Mn oxides and amorphous Mn oxides are believed to be also present in the manganese oxide scale. Tiny particles of PbS04 and SrS04, together with gypsum, other impurities and micro-pores, tend to concentrate in the grooves.IntroductionManganese is a common impurity in hydrometallurgical zinc processing circuits. The manganese originates from sphalerite (Zn,Fe,Mn)S and from the Mn02 added to the leaching circuit to oxidize ferrous ions [1]. Manganese in the sphalerite follows Zn through the roasting, leaching and purification processes, and is present as Mn(II) in the purified ZnS04 solution. The Mn in the added Mn02 is reduced to Mn(II) during the oxidation of the ferrous ions present in the leach solutions. In both cases, MnS04 is generated, and the MnS04 accumulates in the purified solution. In the cellhouse, Zn is plated at the cathodes to produce high quality metal. The Mn(II) is partly oxidized at the anode surface to Mn(IV), and the Mn(IV) precipitates as a scale on the surface of the anode and as a sludge on the bottom of the electrolysis cells. The presence of a thin layer of manganese oxide scale on the surface of the Pb-Ag anode can minimize the corrosion of lead and, accordingly, reduce the contamination of the electrodeposited zinc. However, a heavy manganese scale build-up can cause ""staining"" of the zinc deposits and reduced current efficiencies. Consequently, periodic anode cleaning to remove excess manganese oxide scale is carried out routinely in commercial operations."

Jan 1, 2011

By K. Kalgraf

The motion and stability of the metal/electrolyte interface is determined by Navier-Stokes equation. The equation may be decomposed into two independent equations by taking the divergence and curl of Navier-Stokes equation. The divergence determines the motion and stability of magneto-gravitational waves. The curl of Navier-Stokes equation gives an equation containing only velocity and magnetic field, and states that the magnetic field is driving a circulation pattern in the cell, and this magneto-flow has its own stability conditions. The waves are called Alfven waves, and their stability properties are related only to magnetic field and geometry.

Jan 1, 2001

By T. Shimizu

In Japan, the emission standard of selenium in effluent was set at a maximum of20 mgll in Feb. '94 for the first time, and it is scheduled to be further decreased to a maximum of 0.1 mg/I from Feb. '97 due to tightening of the Water Pollution Prevention Act. Selenium (IV) and (VI) are generally found in effluent from precious metals refineries. Although selenium (IV) can be easily eliminated by some reducing agents, selenium (VI) is more difficult to be reduced. Therefore, many smelters are having difficulty in complying with the new emission standard. At Mitsubishi Materials' Naoshima smelter, the behavior and the elimination of selenium in effluent have been extensively investigated. As a result, it was found that two strategies were particularly effective. One of them is improving the overall operation of precious metals refinery, that is, feeding uniformly the effluent to the waste-water treatment plant, reducing the effluent volume by recycling and recovering more selenium (IV) in the effluent. The other is eliminating selenium (VI) in the effluent from the precious metals refinery. It was found that selenium (VI) can be effectively reduced by using hydrazine under high? sulphuric acid concentration and high temperature conditions. By using these measures, it is considered that Naoshima Smelter will be able to comply with the new emission standard.

Jan 1, 1996

By H. Walqui

Southern Peru Copper Corporation (SPCC) are currently modernizing the Ilo copper smelter. A single ISASMELT furnace will start smelting 1,200,000 tonnes per year of concentrate during the second half of 2006. The existing Peirce Smith converters are being upgraded for converting the matte to blister copper and a new acid plant and oxygen plant are being installed. Two new anode furnaces and a twin anode casting wheel have been installed in 2005 and commissioned in January 2006. The modernization project will ensure the smelter satisfies new environmental regulations due to come into force in January 2007. This paper summarises the background to the modernization project, describes the main design features of the new copper smelter and summarises progress on the smelter construction as of early 2006. This paper describes the genesis of the Ilo Smelter Modernization Project and describes in details the scope and current status of the project.

Jan 1, 2006

By A. J. Paul

Traditionally, 16"/50 caliber projectile shells have been fabricated from forged steel. The Naval Surface Warfare Center (NAVSWC) has determined that cost savings of approximately 60% (-$4.7M/year) as well as improved shell fragmentation can be achieved by casting these shells from austempered ductile iron. One of the technical concerns arising out of this material substitution is the role of the casting process in controlling the quality of the cast shells. Optimizing the process through proper orientation of the mold, placement of chills, superheat, etc., can minimize shrinkage porosity and, consequently, flaw size. For this purpose, the mold filling and subsequent solidification of the projectiles was simulated using a 3-D, fully transient, coupled fluid flow and heat transfer model based on finite differences. Several casting orientations were investigated and the casting parameters were varied to optimize the process and minimize casting defects. A comprehensive software tool, which was developed using state-of- the-art visualization techniques, has been used to analyze the process of casting. Emphasis is placed on the use of this visualization tool as an aid to the foundry engineer for process optimization.

Jan 1, 1992

By Kenichi Moriyama

The Sumitomo Toyo Copper Smelter started operation in 1971, as an epoch-making smelter at which 9996 of the charged sulfur could be captured. In the past ten years, the amount of treated copper concentrate has-been increased from 1,300 l/ day to 1;900 t/ day by the extremely effective application of the oxygen enrichment for a flash smelting furnace and converter furnace. The sulfuric acid production capacity at the acid plant has also been increased up to 1,900 t/ day corresponding to the increase of copper concentrate smelting rate without installing an additional acid plant. Furthermore the sulfur fixed ratio is kept at a high level, more than 99.996. despite the SO. strength fluctuation of the wide range of 596 to 1396 which is attributed to the combination of flash smelting furnace and, P.S. converter. These -operational results at the? acid plant were achieved by several modifications. and two examples are briefly described as follows; (1) Converter modifications in order to cope with the high SO, strength -gas (2) Introduction of the anodically protection shell and tube type acid coolers In addition. the quality of sulfuric acid has been positively increased. For example, the concentration of iron and arsenic, which were the main Impurities in ?sulfuric acid, was successfully .reduced.

Jan 1, 1995

By Moenster J. A., M. J. Sankovitch

Doe Run's Buick Smelter was converted from a primary lead smelter to a secondary lead smelter in 1991. The recycling facility was designed to produce 60,000 tons of refined lead per year from 110,000 tons of spent starting-lighting-ignition (SLI) batteries and 10,000 tons of lead contained in drosses and scrap. Since commissioning, Buick's refined lead output has steadily increased to exceed 120,000 tons for 1999. The production gains have been the result of continuous process improvements, empowerment of the workforee, and development of additional scrap lead streams. The production gains were accomplished while setting industry standards for employee safety, reducing plant environmental emissions and employee blood leads, achieving ISO 9002 certification, and expanding product lines to meet customer requirements. This paper highlights Buick's major accomplishments through the 1990's.

Jan 1, 2000

By C. Beckermann

"A diffuse interface model is derived for the direct simulation of two-phase flows with surface tension, density differences between the phases, and phase change. The derivation starts from the balance equations for a sharp interface and uses a formal averaging procedure on an atomic scale to obtain diffuse interface versions of the equations. Two approaches are considered: (i) the two phases have different velocities inside the interface and separate conservation equations are solved for each phase, and (ii) the two phases have the same velocity inside the diffuse interfuce and mixture conservation equations are solved. Based on a superposition of microscopic (atomic-scale) and macroscopic interface morphologies, an expression for the interfacial momentum source term is introduced that models surface tension effects and accounts for immiscibility between the phases.IntroductionDiffuse interface methods have been a popular tool in the direct simulation of two-phase flows [I]. In diffuse interface approaches, the interface between the two phases is characterized by a rapid but smooth transition in the properties, such as density and viscosity. Usually, a phase function ? is introduced to represent this transition, and the evolution of ? in the domain is computed from a separate equation or recipe. A unique set of conservation equations (e.g., mass and momentum) is solved on the entire domain, irrespective of the phase present, by accounting for the transition in the properties and introducing terms that account for interfacial sources. The continuum surface force (CSF) model of Brackbill et al. [2], which accounts for surface tension, is an example of the latter. The volume-of-fluid (VOF), level set, and phase-field methods are all examples of diffuse interface approaches. The major advantage of diffuse interface methods is that explicit tracking of the interface and the application of traditional sharp interface conditions are avoided. A disadvantage can arise from the artificial smearing of what is in reality an interface of atomic-scale width; however, techniques have been developed to overcome this problem."

Jan 1, 2004

By Rajesh S. Ransing

An intelligent tool has been developed to analyse the quality of diecast components. The influence of both design and process parameters has been studied in great detail. The tool, based on expert systems related technologies, can identify the causes for the defective castings manufactured. Design related causes such as gate position; gate area, runner design etc. as well as process related causes such as cycle time, cavity filling time and melt temperature are suggested by analysing the data on defective castings for a manufacturing campaign. This intelligent analysis is useful for both design as well as production engineers in the decision making process. All the causes for the occurrence of defects are classified into two categories. The firs category is the 'rootcauses' i.e. the causes which are related to the actual process, material and design parameters and which can be directly monitored. The second category is more abstract in nature and is classified as `metacauses'. These capture the scientific rationale implicit in the cause and defect relationships. This knowledge on causes and defects is represented in the form of a structured graph rather than by a set of rules, which, coupled with forward reasoning and heuristic search techniques results in an elegant and efficient approach. Uncertainties and the degree of relationship among causes and defects are represented by a fuzzy probabilistic model.

Jan 1, 1994

By O. Morfín

The most probable source of Pb contamination in the perennial reach of Aravaipa Creek, Arizona, has been determined using Pb isotope ratios and total metals analyses of samples collected from the ephemeral and perennial reaches and mine wastes located in the Aravaipa Mining District . Previously, elevated levels of Pb, Cd and As in fish in the perennial reach of Aravaipa Creek, a protected wilderness area,, were assumed to be due to off-site transport from abandoned flotation tailings piles located at Klondyke, Arizona upstream of the wilderness area.Our work replaces this inference with isotopic data that allows us to confirm this hypothesis. The Pb/Zn deposits of the district were mined between the late 1890s and the late1960s, with the most significant ore production coming from one deposit in a rhyolite dike swarm on the Western front of the Santa Teresa Mountains, a granitic pluton of Cretaceous-Tertiary age (~65 ma). Mineralogy has been well constrained across the length of the lode system: Pb and Zn sulfides predominate in the NW sector, and a mixed suite of hypogene/supergene Pb sulfide and Pb oxide minerals comprises the majority of its SE corner. Total metals analyses and comparison of metals ratios serve to constrain the source and transport of certain metals within different parts of the system. Pb isotope ratios in samples, obtained by ICP-MS analysis, define two distinct contributors. The first end-member (208Pb/204Pb = 38.513 to 38.721 and 207Pb/204Pb= 15.550 to 15.598) is characteristic of the mixed, oxide/sulfide ores at the SE end of the deposit. A second end-member (208Pb/204Pb = 38.855 to 38.946 and 207Pb/204Pb = 15.610 to 15.625) characterizes samples taken from the NW, purely Pb sulfide end of the lode. Pb isotope ratios from perennial reach sediments are closely correlated with ratios given by samples from the Klondyke tailings site and by Pb sulfide samples from the NW sector, the primary source of ores processed at Klondyke.

Jan 1, 2003

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006

By David Hughes

The paper covers the utilization of on-line analysis in process control of solvent extraction in nickel leach solvent extraction processes in Finland and Australia and in copper heap-leach and solvent extraction in Chile. The goals of and requirements for controlling the solvent extraction stages of the processes are reviewed. The applications at three plants are compared. The development of the technology used is reviewed and design considerations are discussed. Requirements for on-line control and analyzer performance are compared. A new generation of analyzers and its effect on the set-up process of a project is introduced.

Jan 1, 2003

By S. P. Marsh, M. E. Glicksman

"The effect of capillarity-driven diffusion on the recalescence of mushy zones is studied in pure materials. The solid-liquid mixture is formed by rapid partial solidification of an initially undercooled melt, and the ratio of the two phases is subsequently maintained constant by an externally imposed adiabatic constraint. A novel technique has been developed that permits tracking of the kinetics of the diffusion-controlled evolution process in situ using precision temperature measurements averaged on a length scale larger than that of the microstructure.The mean ""temperature of a mushy zone is slightly below the bulk equilibrium melting point, and is related to a characteristic length scale of the microstructure through an appropriate statistical average of the GibbsThomson equation. Theoretical considerations indicate that the diffusion controlled recalescence will progress as t- l / 3, where t is time. This behavior is experimentally verified for both succinonitrile (SCN) and ethylene carbonate (ETC), which have markedly different morphologies. The kinetic rate constant is observed to increase monotonically with increasing volume fraction of solid in the two-phase mixtures, although a firm theoretical foundation for this result has not been developed.INTRODUCTIONA dispersed multiphase system seeking equilibrium will generally contain variations in the local .free energy density. These density variations arise from such factors as variations in the bulk free energies of the phases and the distribution of interfacial energies. In this study, we examine the kinetics of diffusion-controlled recalescence in 1 solid-liquid mixture of a pure substance at its melting point. This type of two-phase system is particularly convenient to analyze because of the well-characterized physical properties of pure phases (crystals and their melts) and their interfacial energies, and the absence of any solutal effects."

Jan 1, 1986

Direct electrowinning is an electrochemical process which has been developed for the extractive recovery of copper from dilute, acidic leach solutions. In passing through a thin particulate coke cathode. copper is reduced and electrodeposited in a thin layer forming a solid copper-coke sheet. The product is melted in a furnace to separate the coke, then the molten copper is fire refined to produce a salable product. A description is given of a prototype unit which is designed to treat 20 gpm leach liquor and recover over 100 pounds of copper per day. Economic analyses show that in a commercial facility producing about 25.000 TPY copper.*the direct electrowinning process has lower overall cost than either conventional iron-cementation or the newer liquid ion exchange-electrowinning when the leach liquors contain less than 2 grams per liter of copper.

Jan 1, 1976

By Seshadri Seetharuman

The present paper summarises a series of measurements of the interaction parameter of oxygen in liquid copper with respect to a third element, e(M)o, where M is Mn, Zn, As, Se or Te which are common impurities in the liquid metal. The technique employed was the solid electrolyte galvanic cell method. The cell used may be represented as Pt, W or cermet / Cu-O-M // ZrO2 - CaO // AO, A /PT where AO/A represents a suitable oxide/metal reference. The measurements indicate that Mn and Zn interact very strongly with oxygen in liquid copper while, in the case of arsenic the interaction parameter is nearly zero. The behaviour of the elements Se and Te is unique with respect to oxygen interactions in copper bath. At oxygen levels, xo= 10-4 ? 10-5, the apparent interaction parameters are negative, comparable to that for sulphur. On the other hand, at lower oxygen levels, the results indicate that the interaction parameter values are positive. The results are discussed in the light of some of the theoretical models for solute interactions in liquid metals.

Jan 1, 1993

By N. A. Warner

To filly secure the environmental and social acceptability benefits of making a sulphide smelting facility and its ancillary sulphuric acid plant or other means for fixing sulphur, a virtually zero gas emission operation, it will be necessary to utilise exclusively technically pure oxygen. The strategy proposed for preventing the smelter from overheating involves highly efficient energy transfer by promoting sulphur trioxide formation at a relatively higher temperature than normal. A closed-loop gas circuit uses an eductor system actuated by the process oxygen to recirculate sulphur trioxide and unconverted sulphur dioxide back to the smelter, the endothermic dissociation of sulphur trioxide becoming a major contributor to the removal of excess heat. The only gases leaving the system relate to the bleed of nitrogen impurity introduced in the tonnage oxygen.

Jan 1, 1998

By James C. Foley, David K. Rehbein

"In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent ·advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ evaluations of the acoustic attenuation and velocity as sintering proceeds. Pure aluminum (99.999%) and aluminum alloy powders were prepared with high-pressure gas atomization (HPGA). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and attenuation during sintering. The changes in acoustic properties were correlated with sample microstructures and mechanical properties. Evolution of the acoustic echo train during sintering is shown to provide information on the state of sintering as well as having the potential for detection of interior flaws.IntroductionThe versatility of powder metalallurgy (PIM) technology in the manufacture of complex shapes has enabled an increasing amount of wrought and casting production capacity to be converted to PIM technology. However, ultrasonic inspection of green components produced using PIM techniques remains a challenge and is not generally practiced [1]. Inspection of PIM components in the green state is highly desirable, because the green part can be reclaimed with only accepted components being subjected to further costly processing. Another potential benefit is characterization and greater understanding of the sintering process itself. An increased scientific understanding of the sintering process enables intelligent process control, greater reliability of the production process and a lower rate of rejection of the finished product. In order to realize these potential benefits, it is necessary therefore that accept/reject criterion be based on real time nondestructive evaluation of the green-state components and the sintering process.Most current nondestructive inspection techniques suffer from their inability to perform inspections below the near-surface region with the exception of X-ray and to some extent pulsed eddy current [2]. X-ray inspection requires extensive shielding of production personnel and expensive film and film processing. While development of pulsed eddy current techniques have lessened the impact of the well-known skin effect, the depth of penetration of the induced eddy currents remains somewhat of an issue [2]."

Jan 1, 2000

By Dao-Wu Yang, Ju-Lan Zeng, Li-Xian Sun, Yan Yao

"The hydration heat of the pure cement, the fly ash single-dopped cement, as well as the fly ash and fluorgypsum co-dopped cement were investigated by means of micro-calorimety with an eight-channel micro-calorimeter (TAM Air). The results showed that the hydration heat and the hydration rate could be reduced significantly by fly ash and fluorgypsum. However, the reduction was not proportional to the loading of dopant. The exothermic peak of the fly ash and fluorgypsum co-doped cement was appeared earlier than the fly ash single-doped cement. As the temperature decreased, the hydration heat and the hydration rate of the doped cement were reduced, and the exothermic peak appeared later. The effects of fly ash and fluorgypsum on the compressive strength of cement were also investigated. The results revealed that the early compressive strength of concrete made up of the co-doped cement was largely higher than that of the fly ash single-doped cement. Based on the experiment results obtained in this paper, we could conclude that fluorgypsum is a suitable additive for fly ash-doped cement.IntroductionFly ash and fluorgypsum are industrial waste. In 2008, nearly 400 million tons of fly ash has been produced by coal-burning power plants in China. And it is estimated that this number would exceed 500 million at the year of 2015. Besides, every year the fluoride salt factories in China discharge more than 100 million tons of fluorgypsum. Tremendous of fly ash and fluorgypsum occupy considerable land and contaminate air and water sources [1]. As a result, comprehensive utilization of this two industrial waste has draw great attention from all over the world.Cement is the most-used construction material on earth. But the production of cement consumes huge energy and destroys the environment. This problem might can be partly solved by applying fly ash and fluorgypsum as additive for cement [2-4]. During the last decade, some papers that focused on applying fly ash and fluorgypsum as additive for cement have been published [5, 6]. However, to the best of our knowledge, none of these papers investigated the hydration heat of the fly ash and fluorgypsum co-doped cement.The hydration of cement is an exothermic reaction, which can result in serious problem for mass concrete: The interior of the concrete could reach very high temperature as the hydration proceeded [7-9]. As a result, the great temperature difference between the interior and the outer of the concrete would exist and cause serious thermal stresses. Thus, the concrete would be destroyed by the cracks which in tum are resulted from the thermal stresses [10, 11]. The heat released by the cement hydration and the hydration rate is commonly regulated by adding mixed materials or transferring additive such as fly ash and fluorgypsum [12-14]."

Jan 1, 2011

By Justin Karl, Ali Gordon, James DeMarco, Yongho Sohn

"Aluminum metal-matrix composites are lightweight materials that have the potential to supplant steel in many applications. The current work helps to identify the parameters that confer maximal strength and ductility. Torsion tests were performed on the as-cast aluminum metal-matrix composite A359-SiCp-30% at a variety of temperatures and twist rates. Dependence of material properties on temperature and strain rate were identified from equivalent stress-strain curves constructed from the reduced data. Examination of the microstructure was performed on the as-cast material and on fracture surfaces. A temperature-and strain rate-dependent constitutive model was applied to simulation of the mechanical response of the torsion specimen. Trends in material properties corroborate and extend trends identified previously under tensile loading with regard to temperature and strain rate dependence. Shear properties of simulated specimens agree with properties obtained through experimentation.IntroductionAluminum metal-matrix composites (A1-MMCs) have become increasingly popu1ar in recent years. While unreinforced aluminum alloys have low densities and high ductilities, they are not suitable for many applications due to their lack of strength and stiffness. To provide added strength and stiffness while maintaining favorable densities, it has become common to reinforce aluminum alloys with silicon carbide in various forms, although usually the inclusions are in the form of whiskers or particles. The result is a composite material with superior specific strength and stiffness. While whisker-reinforced composites are expensive due to the necessity of processing by nonstandard techniques and have low transverse properties when rolled, particle reinforced Al-MMCs have transverse material property values almost as high as the longitudinal properties and are not as expensive to process as whisker-reinforced Al-MMCs [1]."

Jan 1, 2012

By C. Dresen

This paper discussed the reaction kinetics of the reduction of industrial phosphate pellets for P4 production. In the reduction process of various phosphate ores, the following parameters were investigated: Diffusion of the phosphorus oxide and other gaseous products from the reaction mixture after having been reduced on the reductant (coke) surface. Influence of silica on reaction kinetics. Temperature influence. Influence of mineralogy and morphology (different ores). Particle size influence of silica and coke. Experiments were carried out in a vertical tube furnace with 2 ores, 2 types of silica and one type of coke. Selected experimental conditions simulated furnace conditions. The following conclusions could be made: Reaction rate increases with the addition of SiO2 into the pellet. The reaction rate increases above 1350°C (melting temperature of the slag). Mixing different ore types in the pellets leads to differences in reduction kinetics. Particle size of the coke particles influence reduction kinetics. The amount of slag formation is influenced by silica addition, coke size and temperature.

Jan 1, 2002