Search Documents

By Hideki Yarnarnoto

The simultaneous removal for NH4+ and PO43- in aqueous solution was carried out by using Ca type zeolite synthesized from coal fly ash. The effect of pH on the cation exchange capacity and adsorption properties of the obtained zeolite, the simultaneous removal of NH4' and ~04'. in various solutions and the mechanism of simultaneous removal were investigated respectivel? ,The Ca type zeolite used in this study can simultaneously remove NH4+ and PO43- In aqueous solution without releasing counter ion, and this method gives great advantage over the other ordinary removal methods.

Jan 1, 2002

By Fuqiang Zheng, Feng Chen, Wenting Duan, Yufeng Guo, Tao Jiang

High-quality titanium-rich material is of significance in the development of titanium industry as it is the main raw material to produce sponge titanium and titanium white using chloride process. Activation roasting of titanium slag with high Ca and Mg contents as adding H3PO4 followed by acid leaching was investigated to prepare titanium-rich material. The effects of H3PO4 dosage, roasting temperature and time, hydrochloric acid quantity, acid leaching temperature and time on TiO2 grade and removal of impurities were studied. The results show that after the finely ground titanium slag roasted with 8% H3PO4 at 1000 for 2h, most Mg impurities in anosovite solid solution structure were converted into simple acid–soluble compounds. The impurities such as Ca and Mg obviously decreased when the hydrochloric acid concentration was 20%, leaching at 100 °C for 2h, from which a titanium-rich material containing 82.56% TiO2 and 1.15% (CaO+MgO) was obtained.

Jan 1, 2016

By Dengfu Chen, Huabiao Chen, Yunwei Huang, Mujun Long, Youguang Ma, Lintao Gui

In the current work, a three-dimensional model coupling turbulent flow, heat and solute transport was developed to investigate the solute transport and redistribution in the mold of slab continuous casting where the Reynolds number is very high and the molten steel flows strongly. The conservation equations of momentum, energy and species for a multicomponent system which includes solute element C, Si, Mn, P, S were solved with the commercial software ANSYS Fluent. The parameters used in the model are based on the actual continuous casting. The fluid flow, temperature distribution and solute elements distribution were analyzed. Results showed that negative segregation occurred near the strand surface, and the species concentration reached a peak value at the solidification front during solidification. The segregation degree of solute element S is higher than the other solute elements because of its lower equilibrium partition coefficient. The species concentration in the liquid pool is homogeneous because of the turbulent flow effect.

Jan 1, 2015

By K. G. F. Janssens

In the process of annealing a deformed metal the microstructure changes due to concurrent recrystallization, grain growth and precipitation. It is common knowledge that all three of these microstructural transformations show a strong dependence on each other, and that an overall model must take the relevant interactions into account. Aiming at the development of an approach which is useful in the more general case, a computational model is being developed which allows the prediction of the three dimensional grain topology and orientation distribution function of any metal submitted to subsequent deformation and annealing, taking into account concurrent recrystallization, grain growth and precipitation and starting from a statistical representation of the deformed microstructure. In this contribution a case study is presented which illustrates the potential and limits of the state of the art in the field. Keywords: Microstructure Evolution Modeling, Irregular Cellular Automata, Deformation, Precipitation, Recrystallization, Grain Growth

Jan 1, 2003

By Stephen C. Britten

An in-situ amperometric slag sensor for measuring the concentration of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The sensor provides the same information as potentiometric sensors while also providing data on the concentration of the transition metal species and the diffision kinetics within the slag. The electrochemical technique utilized in the sensor is similar to methods utilized in aqueous voltammetry.

Jan 1, 1998

By Ronald J. Roman

The shrinking core model for coarse particle leaching has been generally accepted as describing the leaching of a copper oxide or sulfide ore. However, when a mixed oxide/sulfide ore-is leached this model can not be used in its simple form because at least two and possibly three separate leaching processes are occurring simultaneously (dissolution of oxide copper minerals, secondary copper minerals and primarily copper minerals). It has been impossible to isolate their individual leaching curves from the recovery/time curve generated by the column leach test. This paper describes a tests program carried out at the Groupo Mexico, Mexicana de Cobre's La Caridad operation in which the individual recovery/time curves for the leaching of copper oxide mineral, secondary copper mineral and primary copper minerals were developed from standard column leach tests. Once the individual recovery/time curves were developed scale-up of the column leach test results to the commercial heap leaching operation is possible by using the shrinking core model.

Jan 1, 1999

By David Dreisinger

The pressure oxidation of pyrite is an important hydrometallurgical technology, especially in the total oxidation of refractory gold ores and concentrates (gold is locked in the pyrite structure preventing direct cyanide recovery). It has been noticed in some commercial applications and benchscale studies that the leaching of pyrite may be slow and apparently can be inhibited by the presence of molten elemental sulfur in the leach pulp. The purpose of this study was to determine whether Ortho-Phenylene-Diamine (OPD) could be used as a surfactant or dispersant for sulfur in the pressure oxidation of pyrite. OPD has previously been shown to be useful for pressure leaching of zinc and copper sulfides at 150 C.In this work, the interfacial chemistry of sulfur was studied at temperatures of up to 190 C in the presence and absence of OPD and other surfactants. The contact angle between molten sulfur and pyrite was also measured. Finally, the impact of OPD on the kinetics of pyrite oxidation was measured in bench-scale pressure oxidation experiments. The essential finding of this study was that OPD lowers the interfacial tension between molten sulfur and acid solutions and increases the contact angle (reduces wetting) between molten sulfur and pyrite. The work of adhesion between sulfur and pyrite was reduced by more than an order of magnitude in the presence of OPD. In bench scale tests, addition of OPD was found to significantly accelerate the rate of oxidation of pyrite. Conveniently, it was found that OPD was also fully degraded during high temperature oxidation processes. No residual OPD was detected in solution or solid samples from the leach testing. OPD is recommended as a sulfur dispersant in the pressure oxidation of pyrite and/or elemental sulfur containing feeds.

Jan 1, 2003

By S. Goto, S. Yamashita, K. Hata

"The average consumption of zinc dust for purification of zinc leaching solution is more than 25 kg per tonne of electrolytic zinc. Authors proposed to remove impurities in zinc leaching solution by electrolysis instead of cementation by zinc dust. The effects of copper and arsenic on electrodeposition of cobalt in zinc sulfate solution were examined fundamentally using a potentiostat. It is observed that cobalt is easily deposited on a cathode at potentials under -480mV with arsenic. Mesh cathodes of stainless steel and lead anodes were used in a small electrolytic cell and the electrolyte was circulated through 'the electrodes during the electrolysis. The effect of electrolyte circulating rate , pH, cell temperature, current density, and concentration of copper and arsenious ions on removal of cobalt were studied. Removal of Cd and Ni are also examined.IntroductionCobalt is difficult to remove from a zinc leaching solution by a simple cementation reaction using zinc dust. However, it is easily precipitated by zinc dust with co-addition of arsenious or stibinous oxide and copper ion in practical operations(I), (2), (3). The consumption of zinc dust for purification is 16-152 kg per tonne of electrolytic zinc and 65% of this zinc dust consumption is used for cobalt purification. The average retention time for purification of cobalt is 4.5 hours (1). A more economical process for purification is desired instead of zinc dust. The mechanism of this acceleration effect of copper and arsenious oxide on removal of cobalt are explained by the authorsas follows; a galvanic cell is formed between zinc dust and copper which is precipitated firstly, and cobalt is reduced on copper as Co-As alloy by this galvanic current(2). This assumption was confirmed in experiments using a galvanic cell with a membrane( 4). The following galvanic reactions occur between zinc dust and copper precipitate; on copper cathode,2H+ + 2e -= Hz(g)2Coz+ + 2HAs02 + 6H ++ 10e -= 2CoAs + 4HzOand on zinc anode,Zn = Zn = 2+ 2e –This galvanic current becomes almost zero in a zinc sulfate solution which includes only cobalt and no arsenious oxide, and cobalt is weakly deposited on a copper cathode. Cobalt deposition requiers a high degree of cathodic polarization. However, the galvanic current flows almost constantly in an electrolyte, which includes arsenious oxide, and the cathode potential is kept at about -500mV. Cobalt is precipitated as Co-As on the cathode.The authors assumed that cobalt may be removed by electrolysis at a very low current density instead of zinc dust and the following experiments were carried out. In the first part of this paper, the fundamental experiments using a potentiostat on the behaviour of cobalt in zinc sulfate solution are described. In the second part, the results of the electrolysis are reported. Cobalt is removed by a new type of an electrolytic cell, which was desigoed to <Iccelerate the rate of deposition of cobalt. The removal of cadmium and nickel in a solution which includes cobalt and arsenic are also examined."

Jan 1, 1997

By Carl A. Kuehn

At Carlin, Nevada, non-indigenous hydrocarbons were introduced as a bitumen phase which was mobilized due to burial under the Roberts Mountains allochthon. similarly, some indigenous organic matter was locally mobilized. Fluid inclusion and paragenetic data of veinlets formed during this hydrocarbon stage, combined with quantitative modelling or organic maturation, indicate that host rocks had evolved past dry gas conditions of around 1550 and l.l+0.2 Kb in the presence of CH4-saturated, highly saline brine by no later than early to middle Cretaceous time. All hydrocarbons present would have been rendered immobile under these catagenic conditions. Crosscutting relationships at several scales suggest that hydrocarbon mobility may have ceased prior to the intrusion of a series of dikes in the mine which have subsequently been altered and mineralized. Apart from subsequent oxidation, the current distribution and high maturity of carbon-rich zones were established prior to gold introduction. No Evidence has been found supporting proposed hydrocarbon "remobilization" during or after gold mineralization and alteration. The high density of the CH4-bearing fluid requires formation at high pressures (near 1 Kb) and precludes their formation as a result of the "cracking-off" of CH4 from organic matter during a thermal event associated with a shallow hydrothermal system. The density and composition of the fluid inclusions restricted to the early hydrocarbon-stages of the Carlin paragenesis are not unique to the sediment-hosted gold deposit environment of north-central Nevada. Similar inclusions are found in authigenic quartz crystals from Paleozoic carbonaceous shales in central Pennsylvania which have experienced normal metagenesis of indigenous organic matter due to deep burial.

Jan 1, 1987

By M. F. Hochella

Transmission electron microscopy (TEM) and energy dispersive X-ray (EDX) analysis have been used to study the mode of occurrence and mineral associations of gold in partially oxidized high grade gold ore from the Carlin sediment-hosted deposit. Rounded.gold particles have been observed that range in size from 0.03 to 0.1 p.m (300 to 1000 A) in diameter. The gold is associated with maghemite h-Fep3l and a K-Al-Si-bearing phase that is suspected to be illite. Detailed descriptions of gold and its mineral associations in &apos;Carlin-type&apos; gold deposits are critical not only to understanding the mechanism of fluid transport and precipitation of gold, but also to developing improved metallurgical techniques for the recovery of gold from refractory ore. Direct observation of gold in unoxidized ore is rare due to its relatively high degree of dissemination and low average bulk concentration which averages 9 ppm according to Radtke (1). Hausen and Kerr (2) observed 1 to 5 p.m grains of gold directly in oxidized ore but these microscopically visible particles account for only a small percentage of gold present in the ore. The samples used in this study were selected from individual beds of high grade, partially oxidized ore (4.55 oz/ton or 156 ppm gold) that were collected in the Main pit of the Carlin mine. The samples were collected from several thinly laminated carbonate micrite beds within the top 50 meters of the Roberts Mountains Formation. The carbonate micrite has been altered by hydrothermal fluids to a calcite-absent, moderately silicified rock referred to as alteration zone #3 by Bakken and Einaudi (3). Based on petrographic and SEM studies, the samples contain carbonaceous matter, and both pyrite and iron oxide pseudomorphs after pyrite. The oxidation of pyrite may be a pro-duct of deep weathering, in which case limited remobilization of gold may have occurred. TEM sections of the rock were prepared by first embedding small chips in low viscosity epoxy. The epoxy blocks were cut with a Reichert Ultracut E ultramicrotome, producing thin sections less than 0.1 p.m thick. The sections were examined with a Phil-lips 400ST TEM at 120 keV in both imaging and selected area diffraction modes. Native golci*was easily detected in TEM bright field images due to the large electron density contrast between gold and all other phases that are present (Figs. 1 and 2), Gold was positively identified with high spatial resolution EDX analysis in the transmission electron microscope, although selected area diffraction of individual grains was not successful EDX analyses of the platy and massive minerals immediately surrounding the gold particles typically indicate the presence of Si, AI, K, and Fe, However, the d-spacings derived from selected area diffraction of these polycrystalline masses (as, for example, in Fig. 2) give an exact match for maghemite. As a result, there is no diffraction information to identify the K-AI-Si-bearing phase(s). The lack of a diffraction pattern could be due to either electron beam damage or to a poorly crystalline phase(s).

Jan 1, 1987

By Z. Zhang, Cuihuan Huang, Zongshu Zou, Nan Wang, Xueqian Xin

"Vitrification is considered as an attractive procedure for municipal solid waste incineration ash, which can realize the volume reduction and innocent treatment of incineration ash, as well as reuse of bottom ash. The main oxide components of molten ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the total mass. The phase relations and thermodynamic properties of the CaO-Al2O3-SiO2-FeOx-MgO-Na2O oxide system is highly required, and is of great scientific significance for optimization of vitrification processing and sustainable resource utilization of melting slag. A study on the equilibria phase relations of CaO-SiO2-MgO-FeOx system was done by using CALPHAD method based on FactSage in this paper. The modeling parameters for the thermodynamic properties of liquid phase in CaO-SiO2-MgO-FeOx system were established and the equilibrium phase relations of MgO-SiO2-FeOx and CaO-SiO2-FeOx-MgO systems were calculated for different temperatures and oxygen partial pressures.IntroductionThe main oxide components of vitrified bottom ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the bottom ash by weight [1]. During slag processing and modification, the knowledge of thermodynamic properties and liquidus temperature in the related slag system is highly required [2-5], which is not yet available. Through literature survey [6-9], it is clear that the systematic information on the concerned complex slag system is scarce. Most binary subsystems except FeOx-Na2O have been investigated well. Among ternary subsystems, few phase relations of the Na2O-MgO-SiO2 ternary system are available. For the phase relations of the system Na2O-MgO-Al2O3, all the studies are focused on the Al2O3-rich region. Investigation on the CaO-Al2O3-FeOx system is limited to Fe2O3-containing system with relatively higher oxygen potential. Most quaternary systems are not studied well except the CaO-MgO-Al2O3-SiO2 system, mainly due to their metallurgical importance. Figure 1 demonstrates the research status of the vitrified bottom ash slag with almost zero effort [10]. The effort here is defined based on the published literature by considering the number of publications, the investigated composition ranges, and the research details. So far the engineers in the field have to make assumptions of the thermodynamic properties of the simplified oxide system, without taking into consideration the interactions of the different oxide components, which hinders the development of the slag valorization and utilization. In order to provide thermodynamic properties for the application of the vitrified bottom ash, the six-component oxide system (CaO-MgO-Al2O3-SiO2-FeOx-Na2O) will be investigated through both experimental approach and computer modeling."

Jan 1, 2011

By Michael G. King

The primary non-ferrous metals industry is the principal supplier of the minor metals selenium, tellurium and bismuth. It is also a major supplier of antimony. These minor elements are recovered from by-products of base metals production. To ensure that these elements remain available, the cost of production must be compatible with four other factors - method of production, available supply, technological niches, and product stewardship. This paper first describes the relationship between the copper industry and the production of tellurium and selenium. The more complex relationship between the lead industry and bismuth production is then discussed, followed by comments on antimony availability. Product stewardship programs are essential to the growth or certain specialized markets for these metals. Smelters and refineries of non- ferrous metals will play a major role in the recycling of scraps and wastes from these markets. Examples on how such materials can be recycled are given in the paper.

Jan 1, 1995

By William A. Fuchs

A study of carbonaceous ore at the Santa Fe mine (Corona Gold Inc.) shows that there is no quantitative relationship between organic carbon content and preg rob, although much of this material preg robs. However, there is a relation between K20 and preg rob. Preg rob generally occurs only in those samples with greater than 2% K20. X-ray diffraction and chemical . studies show that the critical factor is the illite content of mixed (possibly interstratified) illite-smectite. Apparently illite, at a certain threshold, "geo-activates" the carbon. The potential for easily monitoring preg rob using a gamma ray spectrometer is discussed.

Jan 1, 1990

By Andrey Tarasov, Erki Unn, Valery Paretsky

"The stability of the markets of energy resources and labor in countries of the Baltic Sea Region including Estonia is determined to a significant degree by the use of combustible shales as fuel and their distillation resulting in generation of up to 70% of non-recyclable waste. The objective of this business plan is to substantiate the investments for establishment of a new facility in Estonia for waste-less and environmentally safe processing of fossil minerals and man-made products generated in the shale industry, as well as other hazardous wastes. The proposed facility will use a basically new waste processing technology developed in Russia - i.e., processing in sparged molten slag This technology eliminates any release of harmful pollutants to the environment and a facility using this technology does not require, therefore, any sanitary protection zone.IntroductionIn the Baltic region, and first of all in Estonia and some other European territories, there are large natural deposits of combustible shale, which due to the lack of other own resources of energy and hydrocarbons for the chemical industry is burned and distilled with low technical and economic efficiency generating large amounts of toxic and highly toxic wastes and intermediate products. Currently, the penalties for disposal of such wastes have grown to such an extent that shale burning and distillation might become unprofitable. This might result in suspension of the given operations, which in turn will affect in an adverse way the markets of energy resources and labor market in those countries. Furthermore, in addition to the “shale problem”, Estonia, similarly to most member countries of the European Union, faces the challange of environmentally safe processing of highly toxic wastes, such as municipal solid wastes, oilpolluted materials, medical wastes and infected materials, spent rubber tires, etc. These wastes are at present stored or processed with release of a significant quantities of extremely toxic cancerogenic substances (dioxins, furans) or collected and exported for treatment at an extremely high cost and with a loss of valuable components contained in these types of waste and often with return of supper toxic processing products."

Jan 1, 2008

By KNona C. Liddell

The time and spatial dependence of component and species concentrations during in situ uraninite leaching have been modeled using a reactive transport model based on partial equilibrium between reactive minerals and the solution. The flow field is represented by mixing cells in series. The effects of the H2O2, (NH4)2CO3, and NH4HCO3 component concentrations have been simulated, and results are presented for a one-dimensional flow field.

Jan 1, 1995

By Nan Zhang, Lei Zhang, Gai-feng Xue, Lina Wang, Pu Liu

"A novel ß-diketone modified silica gel was synthesized by a simple reaction. The prepared material was characterized by diffuse reflectance FTIR spectroscopy and it was used for the adsorption of heave metal ions in the industrial waste water. The main parameters affecting the sorption of heavy metal ions, including pH, water flow rate, and elution, have been investigated in detail. Under the optimized operating conditions, most of the targeted heavy metal ions could be removed. The material could be simply regenerated by hydrochloric acid solution. The method is rapid, selective, economic and applicable to the removal of heavy metal ions from industrial waste water.IntroductionToxic organic pollutants and heavy metals ions mainly from industrial activities such as plating, metallurgy and dyeing industries, are a threat to human health and the surrounding environment, because of their toxicity and persistence after being released into the natural environment [1]. These pollutants must be removed or degraded to an acceptable level, before being discharged to the receiving waters. Therefore, detection and determination of heavy metal ions in industrial waste water is very important.Inductively coupled plasma optical emission spectrometry (ICP-OES) is the most used technique for the determination of heavy metal ions because of its capability for rapid multi-element detection over a wide concentration range and with relatively low detection limits. Compared to other techniques such as neutron activation analysis (NAA), X-ray fluorescence spectrometry (XRF) and inductively coupled plasma mass spectrometry (ICP-MS), ICP-OES has the above advantages. Some constituents in industrial waters, such as organic compounds and inorganic salts, may cause matrix effects. In order to achieve accurate and reliable results, an efficient preconcentration of heavy metal ions and their separation from the matrix are usually required."

Jan 1, 2012

By Greg Dowling, Jun Ge, George Shannon, Shufeng Yang, Yongfeng Chen, Lifeng Zhang

"Inclusions in 316L stainless steel ingots poured using two different upgate designs – a traditional upgate and a swirl upgate - were investigated using SEM and ASPEX automated inclusion analysis. The main inclusions were high SiO2 inclusions, MnS inclusions and SiO2-Al2O3-CaO inclusions. More inclusions were detected at the top of the ingot than other places in vertical direction, and more inclusions were at the edge of the ingot than other place in the radial direction. With swirling upgate there were more K- and Na- bearing inclusions than that with the traditional upgate indicating possible more serious flux entrainment with the swirl upgate.IntroductionIngot casting still is very important for production of special steel grades including high carbon chromium bearing steel, thick plate, seamless tube, forgings, bars, and wire rods [1] . During the bottom teeming process, molten steel enters the trumpet and passes through the spider into the runners. Molten steel then enters the ingot mold through an upgate near the end of the runner. In the early stages of filling a mold, a mold flux bag hung in the mold were burnt and the mold flux will cover the top of the rising steel to protect the steel from being reoxidized, acting as well as act as a thermal insulator. So far, some efforts on studying inclusions characteristics in the ingot have been reported. A review paper on the control of inclusions during steel ingot casting was published by Zhang et al. [2] Zhang also studied Inclusions in bottom-teemed ingots of plain carbon steel and found that the >20µm inclusions originated from either the entrainment of mold flux of the reoxidation during teeming process. [3] The results of Nagendra and Du showed that there were more inclusions in the centre part of the ingot [4]. Eriksson et al reported that the composition of inclusions was more complex in the mold samples in comparison to the ladle samples, and more inclusions in the mold were found than in ladle because of the reaction between the mold flux and the molten steel [5]. It was reported that SiO2-CaO-Al2O3 inclusions originating from mold powder with reoxidation product Al2O3 as a part, and there were more inclusions close to the side wall than the center of the ingot in the radial direction. [6]. A more recent investigation showed that four main types of inclusions in runner samples were classified: oxides, sulfides, complex and carbon-nitrides. [7] The flow pattern in the mold during filling has been found to be an important factor regarding inclusions in the ingot. In the early stages offilling a mold, steel enters the mold through the entry nozzle at a high velocity. The effect of the resulting turbulence on the meniscus can lead to the entrainment of mold flux. Efforts have been paid over the years to find methods to reduce the velocity of the molten steel entering the mold, such as using opening angle of the inlet nozzle [8], using swirl blade at the runner [9], using a divergent nozzle combined with a swirling flow generated in the nozzle [10-11]."

Jan 1, 2012

By M. J. Perpich

Electrochemical and chemical leaching tests were carried out on chalcocite, covellite and chalcopyrite in acidified iron sulfate solutions sparged with a mixture of O2 - SO2. The gas mixture catalyzed the ferrous to ferric oxidation reaction in situ and, therefore, increased the redox potential and oxidizing strength of the solution. Anodic polarization curves in dilute sulfuric acid on copper sulfide electrodes showed that chalcopyrite passivates and dissolves at current densities orders of magnitude less than chalcocite and covellite. The addition of a depassivating agent (Ag+) increased the passive current density of chalcopyrite and caused breakdown near 0.625 V (SCE). The depassivating effect was also observed during the leaching of chalcopyrite particulate samples as small amounts of Ag+ added to acidified iron sulfate solutions in the presence of O2 - SO2 mixtures greatly increased the leaching rate and the total amount of Cu oxidized (> 90%). Passivation was prevented in the absence of Ag+ by decreasing the initial oxidizing power of the solution and by pretreating the sample in a reductive leach. Both of these methods resulted in transformation of the chalcopyrite surface from its characteristic greenish-gold into deep black. Increased concentrations of Fe+++ due to 02 - S02 sparging were then able to oxidize the transformation product.

Jan 1, 1999

By Junji Shibata

As one of the effective usages of various wastes discharged in non-ferrous metal industry, the synthesis of hydrotalcite was carried out using aluminum dross as a raw material. Hydrotalcite is one of the inorganic anion exchangers and has layered structure of complex hydroxide. The removal of toxic metal ions such as As(III), As(V), Cr(VI) and Se(IV) with the hydrotalcite was investigated, and the removal properties were compared from the viewpoint of the anion exchange amount and exchange rate. Hydrotalcite can be obtained by a co-precipitation method from the aluminum dross and the waste MgCl2 solution discharged in an aluminum regeneration process. Slight amounts of SiO2, Al2O3, Fe2O3 and so on remain in the reaction product as an impurity component. Interlayer distance of the obtained hydrotalcite is about 0.3nm. Hydrotalcite changes to Mg-Al oxide by the calcination at 773K for 3h, and then hydrotalcite is formed again by a rehydration operation after calcination. The toxic metal ions are removed from aqueous solution by the anion exchange reaction in the pH region where toxic metal ions exist as the anionic species like AsO2-, HAsO42-,CrO42-, and SeO32-. The exchange amount is considerably concerned with the valence of anionic species and the size of anionic species. The removal of toxic metal ions were investigated from the engineering aspects such as the low concentration limit to be removed, the amount of hydrotalcite to be used for the perfect removal of toxic metal ions and so on.

Jan 1, 2006

By Bo Yan, Jiaquan Zhang, Haibo Sun

"Based on the validation of steady-state isothermal mathematical model by a 0.4-scale water model for the single-strand slab casting tundish, the effect of varying pouring temperature on the flow, temperature field, and residence time distribution(RTD) of the liquid steel was studied by a transient hydrodynamic model. Due to the decreasing temperature of ladle stream over a casting period of 50 min, the direction of vortex flow at the downstream side of dam changes to clockwise from the anticlockwise at 4 min after the new teeming, and reverts to anticlockwise direction again at 43 min. Meanwhile, the melt flow state in the dam hole is also varying with time. For conventional isothermal water modeling, the RTD parameters obtained are much different as compared with the non-isothermal ones. For the flow control devices(FCD) design, however, the identical optimal scheme can be concluded from the point of view of isothermal modeling.IntroductionOriginally, tundish was adopted as a buffer and distributor to hold and allocate molten steel for sequence casting upon ladle exchange and to provide a desired steel flow rate to the mould below. With the increasing demand to strand quality, the tundish has become a critical metallurgical reactor to enhance inclusions removal, avoid reoxidation of molten steel, and prevent slag entrapment. The general trends to obtain these metallurgical effects are to optimize steel flow pattern and to extend the residence time of molten steel in the tundish through increasing the volume of tundish and/or using FCDs in the interior of the tundish."

Jan 1, 2012