Search Documents

By A. S. Usmani

The flow associated with the pouring of molten metal into moulds has been modelled on the basis of certain simplifying assumptions. A finite element based Navier-Stokes equation solver has been used to analyse the flow. The velocities obtained from the Navier-Stokes equation solver are used to advect a pseudo-concentration function for modelling the fluid front. A simple problem with a known analytical solution is solved first to test the model. Subsequently, several more examples with varied geometrical configurations are modelled, including one with curved flow boundaries.

Jan 1, 1992

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By Theo Lehner

The Rönnskär smelter has wide experience in the field of recycling of non-ferrous metals. Today, smelting and refining from primary and secondary raw materials are integrated in a complex flow sheet. Boliden operates a lead flash smelter, a lead refinery, a copper smelter and refinery, a sulphuric acid and sulphur dioxide plant, a slag fuming plant and precious metal plant at its Rönnskär smelter in the North of Sweden. The Business Area Smelter Operations also incorporates Boliden Bergsöe, Sweden's lead-acid battery recycler, and Norzink, Norway, where recycled zinc accounts for more than 20% of it's production. Raw materials for the Rönnskär smelter include concentrates, ashes, slags, metallic scrap, electronic scrap and electric arc furnace (EAF) steel-making dust. This paper briefly describes current operations and illustrates current measures to improve productivity. Limits to recycling as experienced by a non-ferrous smelter are, illustrated. The deportment of critical elements contained in raw materials is also discussed.

Jan 1, 1998

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By S. C. Sharma, M. Krishna, N. Sanmukha

"The oxidation behavior of an aluminium composite with 0, 2, 4, and 6% by weight of hematite at 200 to 500 °C has been investigated. Within the experimental temperature ranges a parabolic weight gain was observed. The, weight gain as a function of oxidation time becomes linear after an initial period on oxidation formation, an oxide scale was found whose morphology depends on temperature, cooling rate and sub-scale formation at the interface between the matrix and reinforcement. The presence of hematite particulate reinforcement has very little effect on the oxidation behavior. The interface oxidization rate was found to be higher than that of other regions. The, oxidation products were either metallic oxides or ceramic oxides. The exposure time of specimens to oxidation was 1000 minutes at various temperatures. In the present work key principles of alloy oxidation were discussed. Also the paper emphasizes various reactions taking ' place and the activation energies involved in the oxidation reactions.IntroductionMetal matrix composites (MMCs) reinforced with ceramic particulate, whiskers, or fibers have received increasing attention due to their potentially high fracture toughness and strength 1-5. Particle reinforced Aluminium MMCs find potential application in several thermal environment, especially in the automobile engine parts, space applications, such as drive shafts, cylinders, pistons, and brake rotors6.With the exception of gold, no metal or alloy is stable at room temperature, they tend to form their respective oxides. Most of the metals in the solid or liquid state are morphologically unstable when exposed to air at higher temperatures. An investigation relating to the temperature profiles of the piston area in a diesel engine has shown that the temperature can reach as high as 500¬800 K in certain regions of the piston. As the piston and cylinder areas are exposed to high temperature environment, the MMCs should have sufficient stability on both mechanical and chemical strength (oxidation). Oxidation occurs at grain boundaries in alloys and at the interface of the particulate and matrix in MMCs, which usually enhances intergranular fracture, resulting in premature failure and severe brittleness 8-10. Therefore for high-temperature applications, it is essential to have a thorough understanding of the oxidation behavior of aluminium MMCs."

Jan 1, 2000

By J. V. Atwood

The U.S. Bureau of Mines has developed a novel Double Membrane Electrolytic Cell (DMEC) that exhibits unique features for recycling contaminated metals and metal alloys. The DMEC incorporates two anionic ion exchange membranes, separating anodic and cathodic regions of the cell. The ion exchange membranes prevent significant transport of unwanted cationic impurities to the catholyte from the impure anolyte while the anion/cation balance in cell compartments is maintained through the free movement of anions between compartments. The membrane barrier makes it possible to electro refine highly contaminated materials or to electrowin from solution while utilizing alternate anode reactions. Sinceanolyte and catholyte cross contamination has been eliminated, premium cathode products are produced. The DMEC has been tested at bench, pilot, and commercial scales. Configuration of the DMEC, cell operation, scale, up efforts, and significant design factors are discussed. Two separate recycling investigations utilizing DMEC technology are presented. The first investigation examines recovery of high purity cobalt and nickel from severely contaminated super aIloy scrap. The second involves? upgrading contaminated cobalt in the U.S. Government's National Defense Stockpile. Capital and operating costs for both potential applications are presented.

Jan 1, 1995

By Y. A. Chang

The objective of the present study is to evaluate and compile the relevant phase equilibria and thermodynamic data reported in the literature for the ternary system Cu-Fe-S. It is hoped that the results presented here will be useful to practising engineers and scientists in industry who are attempting to improve continually the existing processes of copper extraction and refining. At the same time, the present work will undoubtedly reveal the lack of some basic data which are important for the improvement of our existing extractive processes. Lastly, this work will also show that the development of theoretical models for the alloy phases in the Cu-Fe-S system is essential before complete consistency between the phase equilibria and the thermodynamic data can be achieved.

Jan 1, 1976

By Musa Karakus

In an attempt to explain the phenomena of lead entrainment during Cu drossing of lead bullion, two different synthetic lead bullions were heated to 1050°C, cooled slowly to various temperatures, and then quenched. The morphology and composition of dross particles that form when Mn is used to desulphurize bullion also were examined. Polished sections of these pyrometallurgical products were examined by process mineralogical techniques to identify the impurity phases, determine their chemical compositions, examine the morphology of the impurity phases and evaluate the potential for lead entrainment in such crystals, and characterize pre-quench and quench-generated phases. The phases crystallized were metallic lead, metallic copper, galena, chalcocite, albandite, Cu14.4Pb2S9. and 5.5Pb2S3.5. Metallic copper formed isometric skeletal crystals, chalcocite formed platy and skeletal crystals, and 1formed crystals and eutectic intergrowth with chalcocite and Cu14.4Pb2S9 or Cu5.5Ph2S3.5. The pre-quench crystals are larger and usually exhibit skeletal forms; the quench-generated phases are only a few micrometers across and disseminated throughout the lead matrix. Skeletal crystals of metallic copper and chalcocite form three dimensional networks that entrain large amounts of metallic lead.

Jan 1, 1989

By Orlando C. Rojas

The Potrerillos Smelter commissioned a new El Teniente converter in 1985. As a result of the use of this technology, the Peirce-Smith converters have been processing only high grade matte or white metal. These operational changes resulted in damages to the converter shells, excessive splashing and cold dope generation and very short refractory campaigns. The paper shows the modifications to the tuyere angle, mouth design changes and new techniques for mouth cleaning and gas handling. Operational results up to 1991 are also shown.

Jan 1, 1993

By René Winand

A new process was studied at large laboratory scale at Université Libre de Bruxelles, under contract with Metallurgie Hoboken-Overpelt. A two cathodes (1m long ; 0.2 m high) channel cell was used at 2000 A/m2, with an electrolyte flow rate up to 1.8 m/sec. The main results may be summarized as follows : cathodes are electro¬refined grade in analysis ; metallographic structure and surface roughness are kept under control up to 1.3 cm (one side deposits) ; silver in cathode is controlled by CI and Br ions in solution ; organics must be used at very low concentrations (in the range of 0.1 mg/1, with a consumption of about 0.01 mg/lh).

Jan 1, 1987

By V. E. Antonov

Hydrides of iron and iron-based alloys are thermodynamically stable only at hydrogen pressures in the gigapascal range and rapidly loose hydrogen under ambient conditions. At low temperatures, however, these hydrides can be retained in a metastable state at atmospheric pressure after being cooled under the high pressure to liquid nitrogen temperature. This review will discuss the current state of studies on phase transformations in the Fe-H and related systems and also on the composition, crystal structure and physical properties of the hydrides, both under high hydrogen pressures and in the "quenched" metastable state at ambient pressure. The studies at ambient pressure include magnetization measurements, X-ray and neutron diffraction, Mossbauer spectroscopy and inelastic neutron scattering. In the sections on Mossbauer and structural investigations of hydrides of Fe-Cr and Ni-Fe alloys new experimental results will be presented.

Jan 1, 2002

By Esher Hsu

Keywords: Recycling, Consumer Battery, Fee rates On November 11, 1999, all types of spent consumer batteries are proclaimed to be collected in Taiwan. Under current recycling system, all producers and importers of consumer batteries have to pay a collection/recycling fee to the Recycling Management Fund (RMF) of EPA based upon the rate approved by EPA. Collectors and recycling plants receive subsidies from RMF according to the collected and treated amounts audited by an independent auditing organization. Collected spent consumer batteries only reached 923 tons in 2002 equivalent to 10% of the total quantity sold at the same year. How to increase the collection efficiency of used batteries becomes an important issue for EPA in Taiwan. The objective of this study is to explore current recycling system of spent consumer battery in increasing collection efficiency. Results provide some suggestions to Taiwan EPA regarding recycling route, recycling system, recycling rates, and recycling subsidies.

Jan 1, 2005

By Kenneth G. Thomas

This paper reviews the alkaline and acid gold autoclaving experiences gained at Barrick Gold Corporation. Alkaline autoclaving was operational at Barrick Mercur, Utah, U.S.A., on carbonaceous/sulphide refractory ore for eight years commencing in 1988. Acid autoclaves have been operational at Barrick Goldstrike, Nevada, U.S.A., on sulphide refractory ore since 1990 and now process 17,500 stpd of ore through six large autoclaves. Information is presented on operating costs, materials of construction, reagent requirements and flow sheet developments that reduced capital and operating costs.

Jan 1, 2000

By Yuanbo Zhang, Bingbing Liu, Zhuyin Chen, Xiao Kang, Chen Liu

Composite agglomeration process (CAP) is an effective method to utilize the iron-bearing dusts generated in the ironmaking plants, by which the dust percentage in the sinter feed can be increased up to 20 wt %. In the current study, a comparison on behavior of iron-bearing dust in the conventional sintering process (CSP) and CAP was characterized. The results showed, in the CSP products, the scattered iron-bearing dust in the mixture was disadvantageous for the sintering indexes and consolidation of the finished sinters. In the CAP products, the main phase in the iron-bearing dust pellets was well-crystallized Fe2O3 grain particles. In the matrix parts, there were more Fe3O4 particles generated, which caused to high RDI+3.15 and low RI of the finished products. The pellets and the matrix parts were bonded by iron oxides and acicular calcium ferrite.

Jan 1, 2016

By L. Lewczuk

A detailed mineralogical and liberation study was performed on the iron ore mill products from the Scully concentrator of Wabush Mines, Newfoundland. Automated image analysis techniques were applied to deter-mine grain size distribution and liberation of all mineral components of the ore. As a result of the study it was indicated that iron recovery can be improved and the Mn minerals reduced in the iron ore concentrate by (a) increasing spiral middlings, (b) regrinding the middlings, and (c) separating the Mn minerals from the iron minerals in the reground middlings.

Jan 1, 1988

By Katsutoshi Inoue

The sulfuric acid leaching of spent hydrodesulfurization catalysts yields an acidic solution rich in rare metals such as molybdenum, vanadium, cobalt, and nickel in addition to aluminum. For the purpose of separating and recovering the rare metals from the solution, basic solvent extraction characteristics of the metals involved with commercially available acidic organophosphorus reagents like TR-83, PC-88A, PIA-8 and CYANEX 272 as well as aliphatic alpha-hydroxyoxime LIX 63 from sulfuric acid media were investigated in the present work. It was demonstrated that CYANEX 272, PIA-8 and LIX 63 possessed excellent selectivity for molybdenum and vanadium over the other metals at comparatively low pH. Further, recovery of molybdenum and vanadium from the total leach liquor by the selected extractants was discussed. Additionally, in order to achieve preferential separation and recovery of cobalt and nickel over an appreciable amount of aluminum from the raffinate obtained after recovering molybdenum and vanadium, a systematic investigation was conducted on synergistic extraction behaviors of the mixed solvents of LIX 63 in combination with a series of acidic extractants such as CYANEX 272, PIA-8, PC-88A, D2EHPA, TR-83 and OPEHPA for cobalt, nickel and aluminum. It was elucidated that all of these mixtures could exhibit a good synergistic effect for extraction of cobalt and nickel, and that the lower the pKa of the acidic extractants, the greater the synergism. Contrarily, the extraction of aluminum, was considerably suppressed by LIX 63. Effective extraction of cobalt and nickel away from aluminum was accomplished from the sulfate solution at low pH (1.0 - 2.5) with the mixtures. In particular, the mixtures consisting of LIX 63 and CYANEX 272 or PIA-8 appeared to be the most feasible and economic from an industrial point of view, yielding acceptable separation efficiency for cobalt and nickel over aluminum and .a low acidity requirement for stripping cobalt and nickel as well as negligible degradation of LIX 63. Aluminum can be readily recovered as sulfate salt from the raffinate obtained after recovering molybdenum, vanadium, cobalt and nickel as outlined above by conventional crystallization method.

Jan 1, 1995

By F. R. A. Jorgenson

The ignition of chalcopyrite and pyrite was studied using laminar flow furnace and thermal analysis techniques which were supported by XRD and optical microscopic examination of the products. In air, chalcopyrite and pyrite ignited at temperatures of 400-500'C and 500-600?C respectively. The phase assemblages predicted from thermodynamic analyses were compared with those found by experiment, and the onset of ignition was correlated against changes in the phase compositions. Pyrite and chalcopyrite ignited when pyrrhotite and intermediate solid solution formed thus opening up the structure and allowing ready access of oxygen.

Jan 1, 1989

By Nathan A. Tiner

Sulfuric acid anodizing process is extensively used in many industrial and consumer products to provide corrosion resistance to aluminum alloys. The anodic coatings produced consist of amorphous alhnum oxide with a pornus structure which is easily sealed and colored with dyes. The coatings may contain defects due to surface flaws, canposition and microstructure of the aluminum alloy, and/or due to the anodizing process conditions. This paper will describe the techniques used in anodizing process, various defects which may be produced in anodic coatings and the methods to control them.

Jan 1, 1992

By Geir Martin Haarberg

Modern electrolysis technologies can provide possibilities for developing sustainable processes in terms of energy and environment. Laboratory experiments were carried out to study electrodeposition of iron from molten salts and aqueous solutions using an inert oxygen evolving anode to eliminate the emissions of CO2. The possibilities of molten salt electrorefining of metallurgical grade silicon to produce solar grade silicon were also investigated. Electrochemical techniques were used to study the electrochemical behaviour of dissolved iron, silicon, and titanium species. Bulk electrolysis was carried out to deposit pure iron, silicon, and titanium. The quality of the deposits was studied by SEM/EDS and XRD analyses. Calculations based on laboratory studies indicate that great improvements in terms of reduced energy consum

Jan 1, 2010

By Thomas Niehoff

Many industrial processes require energy. Energy is required for melting or heating purposes. The heat can be generated by electrical heating or combustion/oxidation of hydrocarbons. Oxygen supports the combustion process. Oxygen is naturally contained in air with about 21 vol.-percent. The use of technical oxygen will allow an increase to the natural oxygen concentration of combustion air. Altering the combustion process by increasing the oxygen content has various effects. These effects are described and analyzed with regard to heat transfer, emissions and energy consumption. Industrial processes requiring oxyfuel are described and discussed regarding energy aspects.

Jan 1, 2008