Search Documents

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By Guo Chen, Jin Chen, Jinhui Peng

"In this paper, the methods of life cycle assessment for microwave hot air systems, and the concept of green degree were proposed. Greenness evaluation index, evaluation system and evaluation model of microwave hot air systems were established. Also, life cycle assessment processing based on these ideas was introduced. Analytic hierarchy process and fuzzy decision- making method were utilized to establish and solve the greenness evaluation of assessment model, while the scores of green degree in microwave hot air systems were obtained. The results show that Life cycle assessment can be applied effectively and efficiently to the microwave hot air systems.IntroductionHot air systems are an important industrial operation condition, which is used to provide high temperature air for materials processing. Nowadays, high temperature airs are manufactured by the conventional heating processes, in which some ceramic materials are used as heating materials. However, these processes pollute the environment. Therefore, to explore new method to produce high temperature air with low energy consumption and less environment pollution are necessary.Microwaves are now being used in various technological and scientific fields in order to heat dielectric materials [1]. Microwaves irradiation has been explored in materials processing in recent years [2-3]. The main advantage of using microwave heating is that the treatment time can be considerably reduced, which in many cases represents a reduction in the energy consumption as well. Since there is energy absorption but no heat conduction, the heating is very rapid and highly efficient, resulting in energy savings and the shortened processing time [2, 4]. Compared with conventional heating techniques, the additional advantage of using microwave irradiation is that microwave irradiation achieves both internal and uniform heating [5-7]. In addition, it is more convenient to control the microwave irradiation processing, because of no direct contact between the heating source and heated materials with less equipment size and waste [2, 8-9]. Life cycle assessment is used and accepted methods for the evaluation of the environmental impacts of products or systems [10]. Recently, many appropriate evaluation methods have been developed for life cycle assessment [11-12]. These proposed methods usually are employed for the evaluating product and analyzing results [13]. Among them, the analytic hierarchy process and the fuzzy comprehensive evaluation stand out as a popular method utilized in many fields [14-16]. Analytic hierarchy process and fuzzy comprehensive evaluation are a combination of mathematical and statistical technique that is useful for analyzing the effects of several independent assessment aspects on the system goal without the need of the predetermined relationship between the objective function and the assessment aspects [17-19]."

Jan 1, 2013

By Qingwei Wang

Heavy metal-containing wastewater from hydrometallurgical processes of lead-zinc was treated by biologics in a 200 m3/h industrial scale experiment. The result shows that Zn concentration declined from 50.28 mg/L~240.81 mg/L to 0.21 mg/L~1.98 mg/L, Pb from 1.00 mg/L~13.47 mg/L to 0.083 mg/L~0.71 mg/L, Cu from 0.24 mg/L~2.38 mg/L to 0.059 mg/L~0.40 mg/L, Cd from 2.12 mg/L~23.47 mg/L to 0.011 mg/L~0.071 mg/L and As from 0.50 mg/L~6.00 mg/L to 0.005 mg/L~0.10 mg/L. The concentrations of the above heavy metals in the treated water were lower than that in Integrated Wastewater Discharge Standard (GB8978~1996) in China. Furthermore, the treated wastewater was recycled and reused in smelter plant. Zinc content in hydrolytic sludge reached up to 34.04%, which indicates that this sludge can be used to recover valuable metals.

Jan 1, 2010

By J. D. Scott

The counter-current jarosite acid wash circuit presently in operation in the zinc plant produces a combined jarosite plus Pb/Ag residue which is discarded. Extensive pilot-scale testwork, and some past in-plant operational experience, has shown that the zinc plant can be easily reconfigured to produce two residues during periods of high silver feeds and/or prices. Plant.optimized circuit configurations are available for silver recovery to a Pb/Ag residue and are in use for the prevention of Pb/Ag-jarosite formation in both the neutral and high-acid leaching circuits. Silver in the zinc plant undergoes several changes in state as it proceeds through these circuits. The roaster calcine is ~3:1 silver sulfate: silver metal, with metallic silver mainly as micro-Inclusions In an aluminosilicate phase. In neutral leach residue, the majority is as silver sulfide or Pb/Ag/Zn-sulfide coatings on unroasted sphalerite grains, with minor Pb/Ag-jarosite and some residual metallic silver in unreacted alumina-silicate grains. In high-acid leach residue, silver occurs as Se-rich silver sulfide particles in sulfur/jarosite ball aggregates, as silver sulfate impregnations in silica-gel masses and in solid solution in Pb/K/Zn~jarosite. Silver concentrations in solution range from 20 to 60 ppb.

Jan 1, 1990

By A. R. Kiani-Rashid

Controlled graphitization has become known as a practical method for improvement of wear resistance and machining properties in steels. In this paper, the effect of heat treatment on microstructure of CK45 steel has been investigated. Austenitising was carried out at 920°C for 5 hours. Besides, isothermal transformation was conducted at 750°C in the time range of 1-20 hours. The microstructure of the steel considerably changes by this heat treatment process which exhibits the effects of temperature, appropriate austenitising duration and isothermal transformation. Conducted experiments show a suitable distribution of semi-spherical graphite particles especially on the surface of the steel. Also, analyses demonstrate that the amount of formed graphite in the austenitising temperature 920°C is more than graphite in single heat treatment temperature of 750°C.

Jan 1, 2010

By W. Murray Small

Nickel plays an important role in determining the properties of many stainless steels and superalloys. Cobalt also contributes significantly to the performance of certain grades of superalloys. A major technical aspect, in which both of these metallic elements are involved, concerns the solubility of nitrogen in these classes of alloys. Beyond certain content limits, dissolved nitrogen may contribute to the deleterious mechanical behavior by these alloys. It is therefore essential to control the level of this element during alloy processing. In this paper, results from several experimental studies have been assembled and are analyzed to describe phenomena related to the individual effects of nickel and cobalt on the solution of nitrogen in several groups of alloys. Both solid and liquid alloy systems are considered. This information may be used as a guide to limit or control the presence of this interstitial element in alloys.

Jan 1, 1993

By Han Yi

The coarse indium ingots produced by Shaoguan smelter contained a lot of impurities. In order to produce the high pure indium with the purity more than 99.99%, the appropriate refining processes were designed and the practice of combined application of Glycerin-KI process and electrolysis in Shaoguan smelter was introduced.

Jan 1, 2005

By Chuanhong Li, Zuohua Lin, Zhancheng Guo

"Catalytic mechanism of CeO2 in combustion of coals was investigated in this paper. Catalytic combustion of four kinds of coals with different metamorphic grades by CeO2 was examined, suggesting that catalytic function of CeO2 increases with increase of metamorphic grade of the coals. One important reason for CeO2 promoting combustion of the coals is that pyrolysis of anthracite is advanced by CeO2, which not only raises the pyrolysis rate and pyrolysis conversion ratio, but increases contents of light components in pyrolysis gas; and both pore space and specific surface area of the pyrolysis char are enlarged by CeO2, which is another reason. In order to realize in situ catalysis for reducing catalyst consumption, it is crucial to increase catalyst particle number and enhance the bonding force between catalyst and coal. In addition, remarkable energy saving effect was observed when a nanometer calcium-based rare earth catalyst obtained by hydro-thermal synthesis was applied to catalytic combustion of coal injection into blast furnace.Introduction Coal combustion is acknowledged as one of the most important coal applications. Since addition of catalysts could reduce the ignition temperature of pulverized coal and accelerate the coal combustion, catalytic combustion is generally accepted as an effective measure to realize fast combustion of coal. Furthermore, different catalysts added may produce different effects on ignition temperature of coal. It is reported activity of catalysts with the same cation follows this order: OH->CO3 2->Cl->SO4 2-; while that of the catalysts which have the same anion follows: Cs+>Rb+>K+>Na+>Ba2+>Li+>Sr2+>Ca2+>Mg2+>Be2+ [1-4] .Due to the special physical and chemical structure, CeO2 plays an important role in the catalysis field. Many literatures point out that CeO2 not only has great catalytic effect on energy conversion, succeeded in catalyzing combustion of gaseous fuels such as CH4, CO, etc. but also can catalyze combustion of some liquid and solid fuels such as JP-10, black carbon, carbon deposit in the automobile exhausts and so on [5-9].Pyrolysis, the first step of combustion, directly influences ignition temperature and combustion rate of coals. So a great variety of catalysts were applied to catalyze pyrolysis of coals. And plenty of studies suggest that the alkali and alkaline-earth metal compounds inherent in the coals show apparent catalytic effect on coal pyrolysis. Meanwhile, addition of alkali and alkaline-earth metals into coal combustion process also indicates obvious catalysis effect, accelerating coal pyrolysis, improving pyrolysis conversion ratio, increasing contents of pyrolysis gases and changing composition of the pyrolysis gases [10-15].Although alkali and alkaline-earth metal compounds have good catalysis effect on coal combustion, their application in the catalysis field was limited because of their erosive attack to the combustion equipments. In contrast, CeO2, as a substitution of the traditional coal catalysts, presents widely potential application due to its good catalysis ability, non-corrosive and nontoxic. However, investigation on CeO2 catalyzing coal combustion is rarely reported. In this work, catalytic mechanism of CeO2 in coal combustion was studied, in an attempt to provide theoretical foundation for developing new catalysis technologies."

Jan 1, 2009

By Shenghui Guo, Jianbo Lan, Hongying Xia, Jinhui Peng, Lihua Zhang, Libo Zhang

Spent Hawaii nut shell was converted into a high-quality activated carbon via steam physical activation. Analysis of the experiment including activation temperature, activation duration, steam flow rate on the adsorption capability and yield of activated carbon were identified. Response surface methodology showed that the activation temperature was identified as 866 , an activation duration of 36 min and a steam flow rate of 2.5mL/min with the methylene blue adsorption number of 195 mg/g and yield of 77.75%. The key parameters that characterize quality of the activated carbon such as the BET surface area, total pore volume and average pore diameter were estimated to be 1125m2 /g, 0.94mL/g and 5.21 nm, respectively. Additionally, by the SEM analyses of char and activated carbon, the surface of activated carbon has large number of pores of irregular and heterogeneous morphology.

Jan 1, 2016

By Shun Myung Shin, Kang Jeong, Kyoungkeun Yoo, Jin Koo, Dong Hyo Yang, Soo Sohn

"The optimum discharging condition to dismantle the batteries without explosion was investigated to recycle the lithium primary batteries, which could be exploded by heating too much or crushing. The 3 waste lithium primary battery cells were discharged with 500 cm3 of 0.5 kmol·m-3 sulfuric acid. Fe concentration and pH increased rapidly after 3 days at 35? and after 1 day at 50?. Chromium concentration increased by 4 days at 35? and 2 day at 50?and then decreased, and nickel concentration was very low. Because Li concentration increased gradually, Li became dissolved after the dissolution of cover material. When the discharged batteries were shredded, the batteries discharged at 50°C were not exploded and those discharged during 3 days at 35°C were exploded. This result shows that the waste batteries could be stabilized within 1 day at 50°C and 4 days at 35°C. Introduction Lithium has some advantages for battery e.g. it is the lightest metals and also has the highest electrochemical potential at 3.04V[1]. For over thirty years lithium primary batteries became famous for their performance in various applications such as IT, medical, and military[2,3]. They gained a reputation for their long shelf life, constant voltage, wide operating temperature range, and low self-discharge characteristics[3-5]. World primary lithium battery market was expected to grow from $820.6 million in 2003 to $1,1355.3 million in 2010 (http://www.frost.com, Frost & Sullivan)[2-4]. The lithium primary batteries have very various sizes and components. Lithium batteries are made with lithium metal as anode active material and non-aqueous solvent as electrolyte. As cathode active material, various kinds of materials were used such as manganese dioxide (nominal voltage, 3.5V), thionyl chloride (3.6V), and carbon monofluoride (3.0V). In Korea, 50 % of the spent lithium primary batteries must be recycled because spent lithium primary batteries have been listed in EPR (Extended Producer Responsibility) of the enforcement degree of the act on the promotion of saving and recycling of resources. However, the batteries have been landfilled since there is no economic method to recycle the batteries in Korea[2,3]. When the batteries were heated too much, charged, pierced, over discharged, or short-circuited, the batteries explode because lithium reacts violently with water or air and because contents such as lithium, electrolyte, and sulfur become flammable by high temperature[4]. Therefore, it is so difficult to recycle safely the spent lithium primary batteries."

Jan 1, 2008

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to smelter smelting plants. In both primary smelting and converting, gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By M. B. Sizgoric

Quantitative mineralogy is used in a study done on an Inco Metals Company nickel sulfide occurrence from 'the Thompson area in Northern Manitoba. The study included: a) determination of the variations in chemical composition of the ore minerals; b) determination of the liberation of the ore minerals for the various types of ore and for different feed grinds; c) assessment of the preliminary mill test results by comparing the mineral distribution in the different tailings. Preliminary mill test results had outlined three main problem areas: 1) unacceptabiy low grade concentrate with, 2) very high weight recovery and, 3) low pyrrhotite rejection resulting in a high sulfur concentrate. The mineralogical study readily explained these results by showing that: 1) between 20 and 40% of the nickel in the feeds and 55 and 75% of the nickel lost in the tailings is associated with pyrrhotite. This accounts in part for the low grade of the concentrates obtained at high recoveries: 2) hexagonal nonmagnetic pyrrhotite constitutes over 90 percent of pyrrhotite. Since hexagonal pyrrhotite floats more readily than monoclinic pyrrhotite, this could be part of the reason for the undesirable high pyrrhotite recoveries into the concentrates. Further test work to establish both the optimal grind and the best conditions for pyrrhotite rejection is therefore mandatory.

Jan 1, 1981

By Batric Pesic

Solvent extraction of nickel and cobalt from the real leach solutions was studied by using a novel extraction system. The extraction system was a mixture of 2,6-bis-[5-n-nonylpyrazol-3¬y]] pyridine (BNPP) and dinonylnaphthalene sulfonic acid (DNSSA). The BNPP represents a novel molecule, which was designed and synthesized in our laboratory. Real solutions for the study were prepared by leaching of two different cobalt-nickel bearing concentrates, cobaltite [CoAsS] concentrate from Blackbird Mine, Idaho, and siegenite [(Ni,Co)3S4] concentrate from Missouri Lead-Belt. The major strength of the system was the selectivity of extraction toward nickel and cobalt from iron containing solutions. Other metals such as Mn, Mg, Ca, Al and As were not extracted. Due to the irreversibility of copper extraction, its removal from solution was required prior to the extraction of nickel and cobalt. Zinc was not as strongly extracted (i.e. its stripping was readily achieved) as was copper . Flowsheets for the recovery of nickel and cobalt were also developed.

Jan 1, 1997

By Michael Altepeter

Big River Zinc Corporation, located in Sauget, Illinois, operates a neutral leach residue circuit. The residue produced in the circuit is sold to lead smelters for subsequent recovery of valuable metals. A research program was initiated several years ago to find a means of treating the residue at Big River Zinc to recover the valuable metals. The Ausmelt submerged lance reactor was selected as the best alternative for the first step of the process. Pilot scale tests were conducted at Ausmelt's facilities in Melbourne, Australia. Separations were excellent. 99%+ of the Zn, Pb, Cd, and Ag contained in the residue reported to the oxide fume. 99%+ of the SiO2,, Fe, Mg, and Ca in the residue reported to the slag which passed the EPA TCLP test. Subsequent leaching of the oxide fumes and purification of the leach solutions using conventional procedures produced solUtions suitable for zinc electrowinning and an upgraded lead sulfate cake for sale.

Jan 1, 1992

By Bora Derin

This work deals with the recovery of valuable metals from the ancient copper smelting slags located in Küre-Turkey. In this process, copper and cobalt were recovered in metallic form and/or as their compounds, whereas iron was recovered as magnetic oxide or pigment. Abrasive grit material was produced using reduced final slag. The process stages involved carbothermal reduction in a DC arc furnace, granulation, leaching, chemical precipitation, selective sulfidizing roasting and product preparations. In this paper, the process stages were described as theoretically and experimentally whereas slag and products were characterized in detail.

Jan 1, 2003

By K. Krishnapisharody, G. A. Irons

"The modeling of gas-liquid plumes in steelmaking ladles has been the subject of many investigations. In most studies, the “modified” Froude number, based on the momentum of the injected gas, has been employed to characterize two-phase plumes. This approach has several shortcomings and is critically reviewed in the present work. Based on an extensive review of previous work and theoretical considerations, it is demonstrated that the injected momentum and consequently, the modified Froude number has no significance to gas blowing operations in Ladle Metallurgy. Instead, an approach based on the “plume” Froude number, previously shown by the authors as the proper form for Froude similarity, is extended as a simpler alternative.IntroductionGas injection is central to most Ladle Metallurgy operations. During ladle processing, the steel melt is usually stirred by an inert gas like Argon through porous plug(s) fitted in the bottom of the ladle or a lance inserted deep into the melt. The purging serves several purposes viz., homogenizing the melt, flotation of inclusions, enhancing the rates both of refining reactions and dissolution of alloying elements and promoting inter-phase interactions in the ladle.The topic of gas injection into liquid baths has been the subject of several investigations in the past. A great deal of this work, both experimental and computational, was devoted to describing the structure and properties of two-phase plumes as reviewed recently [1]. Generally, the ascending two-phase mixture is sub-divided into three distinct regions [2]: the jet core, transition and the bubble plume, respectively. The jet region, where the momentum of the injected gas is transferred to the bulk liquid, is also called the ‘momentum region’. In a similar manner, the plume is called the ‘buoyancy region’ where the motion of liquid is caused by the buoyancy force exerted by the bubbles. The proper characterization of these regions is important for the analysis and modeling of stirring operations in Ladle Metallurgy. Although many mathematical correlations exist for this purpose, some issues of theoretical and practical interest to the modeling of gas-liquid plumes need further attention."

Jan 1, 2012

By Stefan Mutl

By the term sorting one understands the separation of a material mixture into two or several products according to different material characteristics in the preparation technology. The oldest sorting procedure, the handpicking, is less and less used to separate different material mixtures because of the considerable personnel expenditure and the strict hygienic regulations at the workplaces in Europe. In general, the manual assortment is able to solve separation tasks, which could not be solved by machines so far. The picking is one of the most selective processing methods. However, the progress in the computer and sensor engineering today makes the creation of automatic picking devices possible, whose efficiency goes far beyond the possibilities of handpicking. Therefore in the future automatic picking will not only be applied to already common applications like the waste glass assortment by colour, but also to the assortment of complex composed material mixtures e.g. old shreddered cars. Thus, the automatic picking, supported by high performance computer systems and new sensor technology, gains more and more significance within many applications of waste processing. However, in order to apply automatic sorting procedures for different material streams within recycling processes, a substantial research and development need still is existing. The desire of the users is to sort more extensively in order to achieve products with bigger material varieties, In addition, the requirement of the accuracy of recognizing and sorting out of single grains rises, This lecture illustrates the procedure of the hand picking before it was employed in waste processing. Thus, a renaissance of a long forgotten method is happening in terms of today's state of the art procedure "automatic picking". Possible technologies, fields of application and future potentials of this technology are pointed out.

Jan 1, 2003

By Georgios Kolliopoulos

Water is a critical commodity of our generation and a key compound for the chemical and mining industries. Sustainable industrial development is directly associated with the ability to recover clean water from contaminated sources. Forward Osmosis (FO) is a low-energy footprint membrane process allowing the recovery of clean water from high salinity effluent streams. In FO, water is recovered spontaneously into a concentrated draw solution (CDS). Energy is required to separate the recovered water from the resulting dilute draw solution (DDS). In the current work, the fundamentals of the FO process and the most important aspects affecting its performance are discussed. An energy comparison of FO and conventional water recovery technologies is presented. Finally, the opportunities FO presents in the field of hydrometallurgy are analyzed.

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to predict the distribution behaviors of Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag in copper pyrometallurgical process. In this model, as more as 21 elements (Cu, S, Fe, Ni, Co, Sn, As, Sb, Bi, Pb, Zn, Au, Ag, 0, N, C, H, Ca, Mg, Al, and Si) and 72 compounds (in fayalite-slag-making system) or 74 compounds (in ferrite-slag-making system) are considered. Accessory-element behavior is studied for two types of slag , fayalite and ferrite, and two levels of oxidation. The allowance is also made to account for physical entrainment in the melts.-Model simulations are carried out to study the effects of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen enriched air. The model can be used in copper flash process, Mitsubishi process and Noranda process. The predictions by the present computer model are compared with the known industrial data from Gui Xi Smelter in China, Home Smelter in Canada and Naoshima Smelter in Japan and excellent agreement between calculations and industrial data is obtained. In this paper, the effects of oxygen enrichment, matte grade, smelting temperature, and types of slag on accessory-element behavior among matte, slag and gaseous phase have been elucidated.I . IntroductionThe presence of trace quantities of minor elements such as As, Sb and Bi in copper significantly reduces its ductility, electrical conductivity, and lowers its thermal conductivity. Embrittlement of copper also occurs due to impurity-phase precipitates at the copper grain boundary interfaces. They deteriorate not only the electrical conductivity of copper but its workability in hot working."

Jan 1, 1998

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"In the present study classical induction design tools are applied to the problem of heating nonmagnetic metal billets, using 50 Hz AC. As an example of great practical industrial interest, the induction heating of aluminum billets is addressed specifically. The predicted work piece power is compared with the measured work piece power for a long and a short coil, using well established methods, such as those of Burch and Davis, introduced in 1926/28, Dwight and Bagai in 1935, Baker in 1944/57, Vaughan and Williamson in 1945, and by Tudbury in 1960. A calculation methodology based on a combination of the available tools is also introduced and discussed. The method has proven to give an error of <10% of the actual work piece power. An equation for Tudbury's work piece shortness correction factor is disclosed for the first time.IntroductionInduction heating of metal billets is a practical problem, with a geometry suitable for solution using analytical methods. This paper will examine solutions related specifically to round work pieces in round coils, although the methods presented can be extended to other regular shapes of work pieces and coils[l]. The methods can also be extended to ferromagnetic materials with slight changes[2-3]. It is assumed that the coil and work piece have a consistent diameter over their entire length and that the work piece is at least as long as the coil. Correction factors can be derived for the cases where the work piece is shorter than the coil.The study of induction heating by coils began in the late 19th century with theoreticians like Heaviside[ 4]. The work of Burch and Davis[ 5-7] in the 1920' s greatly improved the theoretical understanding of induction applied to metallurgy. Many investigators in the 1930's-1950's: Dwight and Bagai[8], Baker[l-2, 9], Vaughan and Williamson[3, 10] and others[l 1-12] added to our understanding with clearer mathematics, solutions for specific applications, semi-empirical modifications and practical design tools. Much of the accumulated knowledge is available in books, such as Tudbury's practical text or Simpson's engineering guide from 1960[13-14]. Perhaps the best description and derivation of the theoretical and semi-empirical solutions can be found in Davies[15]."

Jan 1, 2011