Search Documents

By R. G. Tarr

During an intense and accurate study of initiation systems used on an AngloGold mine, Mine A, poor drilling practices were revealed. Graphic results of all actual measurements taken are shown below. [ ] Accurate drilling of shot holes will determine whether a mining operation is payable or not and at what pay limit mining can take place. Losing 30 cm of a potential 120 cm-hole length will result in a number of consequences, i.e.: ?Higher stoping costs ?Drilling of one shot hole twice in every five shifts ?Increased explosive cost as a result ?Excess stress on hangingwall and footwall due to bad face shape ?Excessive blast damage before the area is worked out. No wonder we have such a high-risk operation. Drilling accuracy is crucial to the profitability on any mine as profits are directly related to the quality and utilization of the drilled shot holes.

Jan 1, 2000

By Ole Rud Bendixen

Topsoe has developed a Wet gas Sulphuric Acid (WSA) process which effectively recovers SO2 in off-gases from non-ferrous smelters and roosters. The product is concentrated sulphuric acid of typically more than 96 wt% irrespective of SO, concentration in off-gas. The process does not generate any waste products or waste water and does not use any absorbents or other chemicals. In the process, up to 99.3% of the SO2 is converted catalytically into SO3, which reacts with water in the gas, hereby forming gaseous sulphuric acid. The acid is condensed in a WSA condenser of proprietary design. Excellent heat economy and practically no sensitivity to the water balance mean that no extra sulphur burning is required at any S02 concentration, The process is especially well suited for treating off-gases where the SO2 content is lower than approx. 5-6%, and it is a good alternative to a complete renovation of a smelter. However, also off-gas from flash smelter may be treated. The process has found good use in both molybdenum and lead roosters. An example from a molybdenum roaster in Chile shows that 97-98wt% acid is produced from a 2.3 % S02 gas. This plant is situated in the outskirts of Santiago and represented a major local source of SO2. The plan was started in May 1993.

Jan 1, 1996

This is the initial issue of STATE MINERAL SUMMARIES. This publication provides estimated data and summaries of mineral activities at the State level for 1988. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1989

By Yassine Lahmadi, Edoardo Trivellato, Christian Chereau, Bénédicte Robert

Within the framework of the adaptation of the South-East European Technicentre (Technicentre Sud-Est Européen TSEE), SNCF Voyageurs appointed Pini with the project management mission (MOE) for the design and construction monitoring of a road tunnel. This investment has a dual function: during the site transformation phase, it facilitates the work logistics (and shorten traffic flows); and in the operating phase, it is intended to ease all movements on the site over the long term. This is a limited-length gallery (50 meters) to be performed in conventional excavation below Poniatowski Avenue (Paris 12e). The excavation, crossing the entire width of the boulevard, constitutes a major challenge, given the very low coverage (less than 5.5 m), and the surrounding main infrastructures. The same project mis- sion includes the design of the tunnel accesses, via reinforced-concrete frame structures. The targeted design questions several aspects of its execution framework, and particularly, continuous operation must be guaranteed to the neighboring networks during the works. The installation of an umbrella- pipe all along the excavation profile, the progression in divided sub-sections, and the implementation of a complex monitoring system are hence key elements for limiting and controlling any deformation. An exhaustive 3D finite element modelling was performed, taking into account the detailed phasing of construction (pre-support, excavation in divided section, preliminary support and definitive lining), to dimen- sion the structures, and, overall, to analyze the impacts on the neighboring structures and facilities. During the execution phase (planned for mid-2024), monitoring activities with back-analyses as close as possible to the works are planned.

Jun 23, 2024

This presentation is a 20 minute snippet of my professional career, and my progression in the mining industry, from a lazy uni student to an up-and-coming blast engineer in the middle of a mining boom.My name is Daniel Hepburn and I am a blasting engineer for Orica Mining Services. I graduated from Royal Melbourne Institute of Technology (RMIT), in Melbourne in 2003. I completed both of my final year projects with Orica Quarry Services and was offered an assistant shotfiring job, which I accepted and worked for eight months. Having missed the cut-off date for the Orica graduate program, I planned to work with Quarry Services until the following year where I hoped my marks and the experiences I had gained would secure a graduate position. I didnÆt have to wait long, as in August of that year, I was offered (and I accepted) a graduate position in Perth as a technical services engineer for Orica Mining Services. The Orica graduate program is based over two years, and consists of real roles from day one; however, there is also opportunity to fast track the program for high performers. There is a structured rotation, from site to site, interstate or even international if you are so inclined. This includes the backpacker program, which allows graduates to experience the Orica culture in countries of their choice. There are also opportunities to try cross-functional roles in the different Market segments within Orica. I was lucky in that I knew what I wanted to do and where I wanted to work, so I stayed in Perth for my entire graduate program. I was also lucky enough to be fast tracked and finished my graduate program in 15 months. At the end of 2005 I accepted a position as an open cut blasting engineer based in Perth and even in such a short period of time I have already completed a number of major accomplishments. Some of these accomplishments are described below. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By Vernon C. Davis

In initial attempts to mine taconite by conventional open-pit methods, the material tended to break into tabular blocks that were too large to be handled by conventional shovel dippers and were unsatisfactory in an ordinary crusher feed. A great amount of secondary blasting was necessary, which added considerably to the cost of mining. The Bureau of Mines and others are engaged in studies designed to contribute to the solution of taconite-mining problems. These studies concern problems related to drilling techniques and patterns, types and methods of use of explosives, and other factors relative to effecting maximum fragmentation at minimum cost. This report, is concerned with study of the application of shaped charges in drill holes, the effectiveness of shaped charges as compared to capped charges in secondary blasting, and the merits of different drilling patterns and methods of detonation of conventional-explosive charges. Fragmentation of taconite at or near the surface is controlled or strongly influenced by joint and bedding planes. Since all tests in this study were made in a jointed and bedded area, a definite conclusion as to the relative effect of a shaped charge in a drill hole, as compared to a conventional charge at greater depths and tighter ground, is precluded. However, application of shaped charges in primary blasting of taconite appears to be of no advantage. In secondary blasting of taconite, conventional, capped charges produced better breakage than shaped charges of the designs tested. Based on the results of conventional blasting practice in horizontal-, inclined-, and vertical-hole tests, no better fragmentation is obtained from blasting either horizontal or inclined holes, compared to vertical holes. Holes drilled in staggered parallel rows that intersect both series of joint planes at the greatest possible angle, give maximum breakage compared to rows paral-lel to one of the series of joint planes. Methods of detonation made little difference in breakage; but the milli-delay caps produced the best conditions for moving the broken rocks.

Jan 1, 1953

By Rodney R. Krause

In attempting to tell the general public about the coal industry's land reclamation efforts, we have often said, "We're not doing things by the book, because we're still writing it." Like any good catchphrase, the statement is not only striking but true. It is particularly true in the mountains of Appalachia, where the problems of mining; and of reclamation are made more intense by the nature of the terrain. Mining and reclaiming the land "by the book' --which is to say by the methods of contour mining traditionally used in hill country--hasn't worked too well. So a lot of conscientious coal operators and associations are trying new methods--new ways of mining, new machines for seeding and planting, and new species to seed. Not all their experience can be transplanted to other areas, and of course I don't believe that Appalachia is the only place where new methods are being developed. Nevertheless, there's enough action in Appalachia to make a detailed examination rewarding, so let's focus on the hills to see what's new.

Jan 1, 1970

By Betty J. Laswell, Gerald W. Laswell

Rotary drilling in modern open-pit mining is usually considered the lead phase which not only establishes the production rates but frequently limits them. From this viewpoint alone, the drilling phase must be maximized. The drill phase is the step that permits all the other operational phases to function within their design limits. This means that, in most cases, the drill is literally run to destruction to ensure that the shovel will be able to smoothly and consistently load a manageably size muck, the haul trucks can carry a balanced load without having a boulder dropped through the bed, and the crusher can devour constant rock size.

Jan 8, 1978

By Mark Eisner

ONE'S JOB is the watershed down which the rest of one's life tends to flow write the Lynds in the first pages of their classic social study, "Middletown in Transition." Certainly engineers will confirm this statement after a check among those in their own profession with whose lives they are at all familiar. I have no hesitancy in acknowledging the truth of their observation for the men and women who are engaged in the profession of the law. It has been often remarked that American public life is overrun with members of the law profession. The highest public office in the land, that of President. has been occupied by lawyers almost to the exclusion of citizens of any of the other professions. Twenty-two Presidents of the United States out of the total of 31, were members of the bar. For the most part, members of Congress, the governors of the states, the state legislators and the mayors and other local leaders, men who occupy important positions of responsibility and public trust, have had legal training. Now this fact is no mere accident. Those who were fitted for the "job" of the practice of the law are favorably placed with respect to their participation in public life. Thus public service and public office is the watershed down which the "lawyer's" life tends to flow.

Jan 1, 1940

By J. A. Batista-Rodríguez, F. J. López-Saucedo

A new methodology is proposed for the preliminary assessment of coal blend quality, which combines gamma-ray spectrometry and magnetic susceptibility measurements. This methodology does not replacethe conventional methods of assessing coal quality, but can help to control the quality of the coal blending process, as well as reduce the amount of proximate analysis required and the determinations of calorific value and total sulphur. The methodology includes five steps. First, both geophysical measurements aremade with handheld equipment. The samples with magnetic susceptibility ≤ 1 × 10-3 SI are then separated. From these samples, those with total gamma intensity ≤ 20 nGy/h are separated. These samples have a higher calorific value and lower ash and moisture content. To separate the samples of better quality and with lower total sulphur content, in step four the samples with total gamma intensity > 20 nGy/h are separated from those with magnetic susceptibility ≤ 1 × 10-3 SI. This last group includes samplesthat will cause less total sulphur-related environmental pollution. In the final step, the quality of both radioactive sample groups is corroborated from the calorific value measurement and ash, moisture, andtotal sulphur contents in at least 10% of all coal blend samples from both groups. In this study, more than1000 samples were analysed with this new methodology, and the results are remarkably similar to the ASTM classification of the Sabinas Basin coals.

Apr 2, 2022

By George M. Potter

Under contractural arrangements with the Bureau of Mines, Mountain States Research and Development, Inc. (MSRD) completed a technological investigation to determine the feasibility of in situ mining of metal commodities other than copper and uranium, The study was based upon available literature and experience. The selection of potential candidates for in situ mining was influenced by economic importance, probable amenability to in situ methods, and environmental considerations. Four metals (or metal pairs) were chosen for feasibility studies: aluminum (with a copper byproduct), gold-silver, and manganese were recommended for further study and action; cobalt-nickel was also recommended contingent upon preliminary laboratory leaching and recovery investigations and field geohydrological work. Mining and recovery plans and an economic evaluation are included. Other metals with potential for in situ leaching are lead/ zinc, molybdenum, and vanadium.

Jan 1, 1981

By Mark Sherman, M. Dennis, Raj Rajamani

"The two Alumbrera 36ft (10.97m)dia. SAG mills were sized, using the FDW ""Grindpower 'I program, to treat an average of 1852 tph each. This paper describes how modelling of the shell lifter design, using the Millsoft program, identified milling inefficiencies caused by poor charge motion. This explained the ""as built"" circuit's inability to achieve the throughput rates predcted by the circuit's designer. Use of the Millsoft program to design a new, dramatically different lifter configuration, in conjunction with a different approach to variable speed drive utilization, has resulted in an improved charge motion and a 30% increase in hard ore milling rates. The new lifter design has allowed the designer's predicted average throughput rates to be achieved.IntroductionThe Alumbrera project grinding circuit consists of two 36ft dia. X 17ft EGL, 13 500 kW, variable speed, gearless drive SAG mills coupled to four 20ft dia. X 30ft EGL, 6 000 kW fixed speed, gear driven, ball mills. The circuit is configured as two identical grinding aisles, each consisting of one SAG mill and two ball mills. No pebble crushing circuit was installed due to the expected absence of a critical size fraction in the first years of production. However, the grinding circuit layout does incorporate space for a pebble crushing retrofit. At present, only about 5% - 10% of the new mill feed reports as trommel oversize and is recycled back to each SAG mill using a water cannon.The circuit was designed to be ball mill limited and to treat the four major Alumbrera ore types at rates varying between 68 000 tpd, and 89 750 tpd, depending on ore hardness. Average throughput rate, and hence nominal design rate, for the grinding circuit was 80 000 tpd (1 852tph per line at 90% availability)."

Jan 1, 1999

By Richard Peaker, Jens Lichter, Alexander V. Potapov

"The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism.This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.INTRODUCTIONThe great majority of newly installed cells in mineral processing plants world-wide are of the cylindrical tank design and this tank shape offers a number of hydraulic advantages over the older style of square cells. Cylindrical cells give symmetrical flow patterns and by careful design of the mechanism and tank internals, the flow patterns generated can concentrate the more intense mixing in the lower portion of the cell to promote good solids suspension and particlebubble contact. Simultaneously, cylindrical tank design gives a more quiescent upper zone for particle-bubble transport into the froth zone. These symmetrical flow patterns are naturally disturbed in normal operation by the slurry inflow and outflow from the individual cells. The challenge for flotation cell designers is to determine the magnitude of these flow disturbances, and to assess whether or when the inflow and outflow rates have a sufficient impact on the hydraulic flow patterns so as to potentially affect the metallurgical performance of the flotation cell."

Jan 1, 2007

"D bed, Ky., coaL, washing characteristics RII 5140coking coal, reserves, estimate RI 5037Pa., coal, washing characteristics RI 4834, 4941D bed mine, Ky., coal, washig characteristics"

Jan 1, 1960

By John H. Bassarear

The never ending search for lower unit costs led Pima Mining Company's management to study various alternatives shortly after Expansion III was completed. It soon became apparent that a considerable amount of ore assaying 0.35% copper had to be moved in order to maintain mill feed at the desired 0.54% copper content, which is the overall grade of the ore reserves. Detailed investigations revealed that for a period of 8 - 10 years, about 14,000 tons per day of 0.30 - 0.40% copper ore would pass by the crusher en-route to the low grade stockpile. This ore is very hard, very clean and has to be mined at a relatively uniform rate. A six month pilot plant run testing autogenous and semi-autogenous grinding gave very encouraging results. Since no mining costs need to be charged to the extra tonnage (it had to be mined anyway) the only major costs would be against milling. The decision to proceed was made in August 1970 and Fluor-Utah was retained as the prime design construction contractor. Ore was first put through the new mill on December 29, 1971. By March of 1972 design tonnage of 14,000 TPD had been attained. The first three expansions at Pima Mining Company, 20 miles south of Tucson, increased mill capacity from 3,000 TPD to 36,000 TPD. These expansions included a separate, conventional, three stage crushing plant plus additions to the existing concentrator that primarily duplicated the then current flowsheet. Expansion IV, however, consisted of an entirely new and separate primary crusher and a completely new mill building located about 2,000 feet southeast of the 01 d concentrator. The new mill, using semi-autogenous grinding, produces scavenger and rougher flotation concentrates that are pumped to the old mill for regrinding, cleaning, thickening and filtration.

Jan 1, 1973

By Peter G. Kovalchik, Rudy J. Matetic, Susan B. Bealko, Adam K. Smith

Overexposure to noise remains a widespread and serious health hazard in the U.S. service providing and goods producing industries. Excessive noise can lead to poor verbal communication and reduce the ability to recognize warning signals. These dangerous work conditions can also cause stress and fatigue. Occupational hearing loss is a permanent illness, with no recovery currently possible. Method: National Institute for Occupational Safety and Health (NIOSH) has recognized Noise Induced Hearing Loss (NIHL) as one of the ten leading work related diseases and injuries in the United States, and has emphasized its importance as one of the critical areas expressed in the National Occupational Research Agenda. Results: One of the most serious noise problems in the goods producing industries is the operation of continuous mining machines during underground coal mining. In order to minimize occupational hearing loss, noise hazards are “designed out” early in the design process. NIOSH is leading a national initiative called Prevention through Design (PTD) to promote this concept. This paper describes the quiet by design approach of a noise control that reduced noise exposures of continuous mining machine operators by 3dB(A) using the four functional areas of PTD, namely Practice, Policy, Research, and Education.

By A. W. Fahrenwald

FLOTATION practice in Idaho is now about 13 years old. The advance has been steady during these 13 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are clue to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the 8 years which the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened.

Jan 1, 1927

By G W. Wilson, M Aubertin

A desulfurised tailings cover was installed at the Detour Lake Mine in Ontario, Canada, to reduce oxygen penetration into the underlying sulfidic tailings. The cover ranges from one to 1.5 m in thickness and was intended to maintain high water saturation to reduce oxygen diffusion and consume oxygen by oxidation of the residual sulfide minerals. The tailings impoundment was instrumented to measure climatic parameters, water levels and water content profiles within the tailings and single-layer cover. One year of monitoring data was collected. Additional tailings samples were obtained for geotechnical and geochemical characterisation. The average grain size of the cover material was found to be coarser than the underlying tailings. Monitoring also indicated that air entry values of the cover material were lower than the tailings. Numerical modelling was conducted on the cover to predict water content profiles under varying climate conditions together with the depth of oxygen penetration and diffusive oxygen fluxes. Estimates of the diffusion coefficient and kinetic oxidation rates from field data compared well with values obtained by laboratory measurements. Numerical simulations indicate water saturations of less than 85 per cent can be expected under varying climate conditions. Predicted oxygen flux rates through the desulfurised cover over tailings with high acid potential indicate low flux rates reaching these tailings due to either consumption of oxygen by residual sulfur within the cover or saturation of the underlying tailings.

Jan 1, 2003

By W. G. Millar

Until a fire occurs, insurance and prevention work are often looked on as unavoidable necessities, but as insurance is back of all business credit, it is essential to know that in case of damage money will be available to cover the loss; while the interruption of production, often caused by a fire, brings home the realization that if prevention work avoids such an interruption, it is well worth while. Fire insurance is a legal contract guaranteeing the payment of large amounts to an owner, but it is possible there is no other important contract that receives so little consideration. Although previously carried on elsewhere, it is only of recent years that insurance engineering has been actively followed up in Canada, with inspections of an owner's property carried out for his benefit. Now inspections of this kind are made, advice on fire prevention and protection work ?is available, reports with recommendations with regard to the above are furnished periodically, and with this method applied the owner receives the broadest possible cover and security at the lowest cost. Rates are set by the underwriters by rating schedules which charge for defects in a building and allow credits for protection and other favourable features . These schedules are based on the past record of loss of mining properties as a class, so that a fire in another mining property indirectly affects you, but the amount paid is reduced in proportion as your property is improved. The writer feels, from personal experience, that there is no industry where fire prevention receives more attention than the mining industry, and it is a pleasure to advise that, due to this co-operation, some reduction in the basis rates for mining risks is now being made by the underwriters.

Jan 1, 1928

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013