Search Documents

By I. Druce, C. Li, T. Qu, J. Dong, W. Y. Xinchao, V. Nkuna

CITIC Heavy Industries has a large installed base of grinding equipment throughout Africa in different configurations, including high-pressure grinding rollers with ball mill and semi-autogenous ball crusher. The total installed power of CITIC’s mills exceeds 430 MW. In this paper, we compare several typical grinding circuits of copper in Africa with about 15 kt/d throughput based on ore properties, process selection, equipment sizing, and key equipment capital and operating costs. Actual operating performance is also introduced. The comparison for the following mine sites provides a general reference for the selection of copper grinding circuits with this approximate throughput: Kamoa-Kakula Copper Mine with high-pressure grinding rollers with ball mill circuit, and Deziwa and Sicomine Copper-Cobalt Mines with semi-autogenous ball crusher circuits

Jan 1, 2023

By U. Schoepf

Economic and at the same time environmentally acceptable mining of small vertical ore bodies and veins to great depths has always been a challenge for miners. The Bauer cutter system, widely used in civil engineering, has been further developed for applications in exploration and mining, to a sustainable system for selective mining with a focus on small vertical ore bodies and veins, as well as residual ore in open pit operations. Current situation of conventional mining of small ore bodies and vertical veins Small ore bodies and vertical or near-vertical ore veins often pose a challenge to the mining industry. The relatively small size of the ore deposit over great depths or lengths, with only limited exposure to the surface makes economical mining difficult. Open pit mining of such ore bodies must either be terminated early because of the high stripping ratio and the enormous environmental impact or is unprofitable from the very beginning. The required massive stripping of waste rock leads to high material hauling times and costs, intensive roadway and bench construction and maintenance, possible safety hazards due to heavy vehicle movement, pit wall stability risks, intensive surface water management and massive waste dump requirements. In addition, it can be assumed that increasingly extensive rehabilitation measures will be required in the future after mine closure. Particularly in vertically oriented magmatic and hydrothermal deposits the technical, economic and environmental limits for further pushbacks, to extend the open pit depth, can lead to an early end of mine life even if a significant quantity of residual ore is left behind. Going underground is only a viable option in a limited number of mines with very high ore values and volumes. The high development cost of an underground mine, as well as the higher underground mining costs, often prevent further mining to greater depths.

Feb 1, 2023

By N Anderson

The world-class Golden Mile gold deposit in the Eastern Goldfields of Western Australia is part of the Kalgoorlie Consolidated Gold Mines (KCGM) operation, which is wholly owned by Northern Star Resources Limited. Current mining operations across the Golden Mile is dominated by the large Fimiston Open Pit, which is over 4 km long, 1 km wide and 600 m deep. It is part of a larger mineralised system that stretches over 8 km and includes the Mt Charlotte Underground Mine, which is also operated by KCGM, as well as numerous historical open pit and underground mines. This mineralised system has been continuously mined for over 125 years and is set to continue well into the future. The Golden Mile deposit is in the Norseman Wiluna Greenstone Belt which is made up of a series of mafic volcanic and sedimentary rocks that have been structurally deformed and intruded by granitic rocks. There are two main styles of mineralisation across the Golden Mile. Firstly, the Fimiston style, which consists of shear hosted Golden Mile lodes with abundant sulfides and tellurides and secondly, the Charlotte style that comprises younger stockwork veins. Fimiston style mineralisation is the primary style of mineralisation within the Fimiston Open Pit. Historically, in excess of 3500 m of underground development and over 755 stopes were mined prior to the consolidation of the area and the commencement of Fimiston Open Pit operation. Old underground workings, known as voids, are either empty or backfilled and extend to more than 1.2 km below surface. Although they are a routine part of mining operations at KCGM, voids pose a significant challenge for the geology team in terms of planning and executing exploration and grade control drilling, geological modelling, grade and tonnage estimation, drill and blast design and execution, marking up ore block designs, mining, and reconciliation. This paper will discuss the various challenges faced by the geology team due to the presence of voids, solutions used to overcome some of these challenges and the results of these activities.

Mar 22, 2022

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

Rammed stone columns and similar reinforcement systems are used worldwide more frequently as a cost-effective method for improvement of foundations on soft soils. The effectiveness of the treatment method is evidenced by the increase in bearing capacity and reduction of compressibility of the treated ground. In this study, two job sites with over 500 stone columns were studied. On both jobs sites, shallow soft silty soils were found and stone columns were designed to support the foundations of MSE walls, which serve as abutments for viaducts. In order to verify the soil improvement efficiency CPT tests were performed before and after the construction of stone columns, also plate load tests were performed on both job sites to verify the deformation modulus of the stone columns. From CPT data it was observed an increase up to 30% of sleeve friction and 20% of tip resistance, which demonstrated a higher deformation modulus maintaining the same strength in the soil after stone columns construction. The plate load tests yield load-deformation curves which indicated that the original assumed modulus was conservative. As a result of these findings, optimization of the settlement reduction ratios was conducted using the modified values of deformation modulus for the soil and stone column, obtaining a reduction up to 30% of stone columns for further job sites with similar soil conditions.

Sep 8, 2021

By T. Struminski

The paper is aimed to assess the possibilities of usage of pyrometers and thermal cameras to study ventilation and environmental conditions in underground mines. Surface and underground thermovision tests were carried out in the Rudna mine and included channels and diffusers of some selected fan stations, shaft crest closures, engines of central fans and their instrumentation. The thermovision underground tests in the Rudna mine consisted of ventilation barriers, underground fans, temperature of rocks, ventilation machines, parts of belt-conveyors and electric machinery.

Jan 1, 2003

By Robert B. Parsons

"Recent amendments to the so-called ""flow-through share"" rules in our income tax legislation have given a new lease on life to this once popular investment vehicle.The original ""Dome funds"" for exploration in the Beaufort sea recognized the usefulness of flow-through share arrangements, but, by and large, flow-through shares have until recently not been able to compete effectively with other tax shelter instruments-mainly , limited partnership interests.This month, Tax Notes examines the new tax rules for investing in flow-through shares.IntroductionRecent income tax amendments have helped to rekindle investor and industry interest in so-called ""flow-through shares"" as a mechanism for mobilizing funds toward mineral exploration and development activities. In competing for investment funds, flow-through shares have historically placed a distant second in terms of investor popularity, being unable to compete with the more attractive features of limited partnership arrangements. However, primarily as a result of favourable changes to the income tax law, flow-through shares may be well poised for a comeback.This article examines the income tax considerations pertaining to issuing and investing in flow-through shares, and compares the former and the new income tax rules relating thereto. Of course, inasmuch as a flow-through share issue can involve various contractual arrangements between the investor and the issuer, there is a wide range of legal and business factors that generally have to be taken into account. A discussion of these matter s is beyond the scope of this paper, which is restricted to a summary of the special income tax factors attributable to flow-through shares."

Jan 1, 1983

By Sam Warren, Antonio Marinucci, Genesis Z. Figueroa, Anne Lemnitzer

Drilled Displacement Piles (DDP) provide an ideal deep foundation solution that combines the benefits of ground improvement with traditional advantages of piling systems. This paper consolidates data from 20 construction projects in which more than 30 DDPs were installed and tested axially. High quality site exploration data (e.g., Cone Penetration Test and Standard Penetration Test) were evaluated to derive geotechnical analysis parameters. The test sites consisted of mostly mixed soil types with strongly stratified layers of sand, silt, and clay. Pile diameters ranged between 40 cm and 61 cm. Test results were compared with predictive methods developed specifically for DDPs as well as methods used in general geotechnical practice. The accuracy of the empirical methods is presented in terms of total pile capacity, pile length/diameter, and soil type. The large majority of all examined methods underpredict the in-situ pile capacities. It was also found that the difference between the tested and predicted capacity is strongly related to the level of improvement in the surrounding soil due to the piles’ installation. A general comparison between predictive axial accuracy and the observed level of ground improvement upon installation is also discussed.

May 1, 2022

By Monte R. Hieb

Study of moisture-induced swelling strain in Pennsylvanian Period rocks of the Appalachian Plateau in West Virginia shows a 2:1 biaxial horizontal anisotropy which trends NW-SE. Oriented in-situ slabs of coal mine roof rock were collected across West Virginia, dry-sawed to size, air-dried to stability, and then monitored for moisture changes and deformations in the horizontal plane through one wetting cycle and drying cycle. Biaxial swelling strains were exhibited in nearly all rocks tested, with maximum horizontal deformations occurring normally-incident to the strike of regional geologic fold structures. This relationship persists as fold strike varies across the study area. A connection with Alleghanian fold development and/or post-Alleghanian fold relaxation is suggested. Deformations were largest in shales, but occurred in sandstones and siltstones as well. During testing, moisture-induced fractures (MIF) developed parallel to the regional fold structure and ranged in size from hairline cracks to sample-destroying cracks that were orthogonal to the observed biaxial swelling strain direction. Preferential wetting and swelling of clay minerals along NE-trending fractures, related to a fold-parallel fracture fabric of regional extent across West Virginia, is the most likely reason for the observed systematic NW-oriented biaxial swelling strains. The testing methods used in this study are simple and inexpensive and produce robust results that offer insight into a regional, anisotropic mechanical weakness that imparts a dynamic, asymmetrical horizontal stress to moisture-sensitive coal mine roof rocks over time. Because a similar mechanical fabric has been reported in Devonian-age shales, these findings may have implications for shale gas developers in the Appalachian Basin challenged by rapid aperture closure rates along horizontallydrilled induced fracture networks in Devonian rocks like the Marcellus Shale. The paper concludes with an example of how the concept of a preferred swelling strain direction might be applied to improve the effectiveness of roof trusses.

Jan 1, 2013

By G. Scamans, J. Lazaro-Nebreda, Z. Fan, J. B. Patel

"Melt quality is crucial for both continuous and shape casting of light alloys and in order to improve it, removal of excessive inclusions, accumulated impurities and unwanted gases becomes necessary. To address this problem, a new multi-purpose high shear liquid metal treatment technology, based on intensive melt shearing by a rotor/stator unit, has been developed. The device ensures achieving uniform temperature and chemical composition and an efficient dispersion of gas and solid phases in the melt with minimal disturbance of melt surface, and can be used, among other things, for de-gassing and de-ironing of Al-alloy melts. Efficient degassing is achieved by dispersing each argon bubble into many small ones, which significantly increases the overall surface area of the bubbles and the time they remain in the melt capturing hydrogen before reaching the surface. This allows using much lower inert gas flow and mixing times than conventional rotary degassing. When applied to Al-alloy scrap, with accumulated iron, the high shear melt treatment speeds up the nucleation and growth of primary Fe-rich intermetallic particles, allowing a faster removal rate. Therefore it reduces processing times, increasing recycling productivity, and facilitates full metal circulation of secondary Al-alloys.INTRODUCTION Aluminium and magnesium alloys are widely considered in various industrial sectors for the purpose of weight saving (Polmear, 1995). In particular, they are used in the automotive sector, where components are mostly manufactured by high pressure die casting (HPDC) because of its simplicity and relatively low cost, but efficiency and mechanical properties are quite low compared with other processes. To date, the main focus to overcome this problem has been for improving the HPDC machinery (Dahle, 2001) but little attention has been paid to the opportunities of controlling the nature and quality of the molten metal supplied to the die. In this way, liquid metal treatment, which involves a variety of physical and/or chemical processing methods to improve melt quality prior casting, is crucial for both continuous and shape casting products."

Jan 1, 2018

By Arash Nikvar-Hassani, Lianyang Zhang

To address the drawbacks of the conventional portland cement/fly ash (PC/FA)–based cementitious material currently used in practice to construct pumpable roof supports (PRSs), a novel cementitious material has been developed based on geopolymerization technology. The novel cementitious material is comprised of two pumpable grout streams: Stream 1 is a slurry composed of pozzolanic material and high-calcium additive and stream 2 is an alkaline solution comprised of a gelling agent. Biopolymer has been added to the second stream to provide ductility to the geopolymer cementitious material. In the laboratory scale, systematic experiments have been carried out to investigate the viscosity, setting time, and uniaxial compressive strength (UCS) of the new cementitious material and develop the right recipe for field applications. By collaborating with industry and the National Institute for Occupational Safety and Health (NIOSH), full-scale PRSs have been constructed and tested. The results show that (1) the novel cementitious material based PRSs has much higher peak UCS and similar or higher residual strength than the conventional PC/FA-based PRSs; and (2) unlike the PC/FAbased cementitious material, the novel cementitious material shows good long-term durability with nocracking/disintegration when exposed to air.

Jul 1, 2023

By D Reid, J Black

The adverse health impacts from diesel particulate matter (DPM) exposure are a well-known global concern. The building evidence has triggered underground mining operations to review existing atmospheric conditions and assess the scale of the challenge faced. South32’s Cannington Mine (Cannington) evaluated the ability to provide a healthy atmosphere from a whole mine approach, taking into account existing preventative controls including: maintenance strategies, fuel quality, mining operations, ventilation provisions, monitoring protocols and effective education and training programs.During the evaluation process, Cannington gave due recognition to the advice and guidance provided in the Queensland Guidance Note 21 (QGN21), the Guidelines of New South Wales’ MDG29 and Mining Industry Advisory Committee (MIAC) of Western Australia. Each of these documents advises a dilution rate of >0.06 m3/s/kW is best for reduction of DPM exposure in underground mines.Achieving the prescribed mine ventilation rate typically results in the need to directly invest significant capital into increasing ventilation infrastructure in order to further dilute contaminants. In today’s economic market of volatile metal prices and increasing pressures to meet regulatory requirements, it can become challenging for established metalliferous operations to create a balance between optimisation of current ventilation infrastructure and capital outlay.In order to obtain and correctly justify the requirements for capital investiture Cannington conducted a ventilation operational analysis for the life-of-operation, identifying the existing air volume envelope was adequate for current and future production rates by optimising existing primary ventilation infrastructure through the implementation of a modified ventilation on demand (VoD) and air conservation system.This process achieved sustainable operating and capital cost reductions without compromising delivery of adequate ventilation to work areas. The process also recognised that engaging mine workers’ ownership of their work areas is crucial to maintaining a technically efficient and operationally robust ventilation system.This paper will concentrate on Cannington’s existing preventative controls, their implementation and their management for the prevention of increased DPM exposure; reducing the risk of both short and long-term health impacts to ‘as low as reasonably achievable’ (ALARA).CITATION:Black, J and Reid, D, 2017. Delivering a healthy atmosphere underground in a cost-conscious environment, in Proceedings Australian Mine Vent Conference 2017, pp 159–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Michael Sheedy

Recoflo® ion exchange technology utilizes fine mesh resin beads, a fully packed resin bed, and counter-current regeneration. These unique features help to improve exchange kinetics, reduce regenerant consumption, and increase the concentration of strip solutions. Commercially, Recoflo technology has been extensively used in the following areas: the separation of strong mineral acids from dissolved metal salts, the purification, removal and recycle of dissolved metals in the surface finishing industries, and the production of high purity water. In the mining and metallurgical industries Recoflo ion exchange systems have been installed to treat a copper refinery bleed stream at Falconbridge's Kidd Creek plant and to treat a nickel and cobalt bearing ammonium sulfate effluent stream at another primary metal producer's facility. In the first application an APU® Recoflo system is used to separate the sulfuric acid at 200g/L from the dissolved copper and nickel sulfate salts at 80 g/L. The absorbed sulfuric acid is recovered from the resin by elution with water and is then returned to the refinery electrolyte circuit. In the second application a chelating ion exchange resin is used to remove nickel and cobalt at 0.01 - 3.0 g/L from process streams containing 120 - 240 g/L ammonium sulfate. This Recoflo system has been designed to reduce the nickel and cobalt levels to 0.001 - 0.002 g/L while recovering cobalt and nickel at concentrations up to 30 g/L and 15 g/L respectively. Case studies for both these metallurgical applications and other Recoflo processes are presented in this paper.

Jan 1, 1998

By J. C. O'Rourke

"This paper presents an overview of Alberta Oil Sands Technology Research Authority's in situ oil sands recovery project at its underground test facility near Fort McMurray. It covers the rationale for horizontal wells drilled from tunnels below the oil sands, the tunnel layout, the drilling program, and the recovery process and facilities. INTRODUCTIONThe Alberta Oil Sands Technology and Research Authority (AOSTRA) has constructed an Underground Test Facility (UTF) in the Athabasca oil sands deposit in northern Alberta, approximately 50 km northwest of Fort McMurray (Fig. 1). The facility initially is to serve as an underground laboratory from which to field test new approaches to in situ recovery of the bitumen (oil) in the Athabasca deposit.The UTF employs mine access to get at the effective exploitation of an oil reservoir. It does so, however, under conditions considerably more difficult than those faced by most other applications of the technology. Because of the unconsolidated nature of the McMurray formation, the development of drilling chambers directly in the reservoir would be prohibitively expensive. Further, mobilization of the extremely viscous bitumen requires intensive steam stimulation with the attendant concerns of large, complex well completions and potentially hazardous operations Over-all, the oil sands presents mining, drilling and operations challenges which push the technology to a new state-of-the-art. The UTF as it now exists consists of:• a 20 000 ha lease with all-weather road access;• 925 m of 5 m by 4 m tunnels in the limestone 15 m below the oil sands at roof depth of 178 m below the surface (Fig. 2);• two 3 m diameter steel lined shafts to a depth of 213 m;• administration and sur face mine support facilities from which to operate the UTF (Figs. 3 and 4);• underground piping systems to transport drill fluids, steam, produced fluids and services to and from the future well heads underground (Fig. 5);• surface steam generation and production handling facilities (Figs . 3 and 4).• a drilling rig and auxiliary systems specifically designed to drill long horizontal wells into the oil sands from tunnels in the underlying limestone (Fig. 6);• an experienced staff to engineer and operate the facility (Fig. 7)"

Jan 1, 1989

By A. F. Robertson

"INTRODUCTION This report is supplemental to R.I. 4178 and deals with the work accomplished between June 15, 1945, and September 7, 1945, on the Mitchell-Hodge mine, Grady mine, Albea and York property, and Cuzzort property.ACKNOWLEDGMENTSIn its program or exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigcal Branch, O. C. Ralston, chief, analyzes samples and performs benefication tests.Acknowledgment is due Mitchell H. Kline, chief, Raleigh Division, Mining Branch; Abraham L. Fox, acting chief, Raleigh Division, Metallurgical Branch; and Rowe McCrae, district engineers, U.S. Bureau of Mines, Gainesville,"

Jan 1, 1946

By X-F Zhao, J-W Li, L-P Zeng

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of Kiruna-type deposits has been ascribed to either immiscible iron phosphate melt separated from silicic magma or precipitation from magmatic-hydrothermal fluids. The early Cretaceous Ningwu volcanic basin in Eastern China contains tens of Kiruna-type iron deposits. The orebodies are mainly hosted within the top zones of subvolcanic dioritic intrusions and along the contacts between these intrusions and adjacent volcanic rocks/strata.The orebodies are commonly associated with widespread brecciation and wall rock replacement. Magnetite formation was closely associated with extensive hydrothermal alteration that may extend kilometres, with both vertical and horizontal zonation. Field and textural data indicate that magnetite formed slightly later than albitisation but coeval with apatite and actinolite. Elemental analysis of magnetite and apatite from ores shows distinct features to those as igneous accessary minerals in the host dioritic intrusions, suggesting a genetic relationship to magmatic-hydrothermal processes. Magnetites have elevated TiO2 (up to 5 wt per cent) and V2O3 (up to 0.7 wt per cent), which implies that they are derived from incipient high-temperature magmatic fluids. It is concluded that the Kiruna-type deposits in the Ningwu basin most likely formed from high-temperature magmatic-hydrothermal fluids. The emplacement of dioritic intrusions into a subvolcanic setting likely plays a critical role in the development of Kiruna-type deposits.CITATION:Zhao, X-F, Zeng, L-P and Li, J-W, 2015. Kiruna-type iron deposits in the Mesozoic Ningwu volcanic basin, Eastern China – origin and relationship to subvolcanic dioritic intrusions, in Proceedings PACRIM 2015 Congress, pp 657–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By F. Liu, H. A. Meier, D. M. Valiveti, P. A. Gordon

Hydraulic fracture is a frequently used technique in the Oil and Gas industry to create high permeability pathways for extraction of hydrocarbons. Numerical simulation of this method poses challenges such as representation of 3D fractures, propagation of randomly oriented fractures in 3D media, enabling fluid leak-off from fracture to poro-elastic medium. We have developed a numerical model using the Generalized Finite Element Method (GFEM) to simulate fluid driven fracture in a poro-elastic medium that addresses these challenges. In the GFEM framework, special enrichment functions are used to augment the solution space in the displacement and pore-pressure fields in order to accurately capture the response in the vicinity of the fracture. Adaptive refinement of the finite element mesh is also employed to facilitate accurate and efficient solution of the model. Our model fully couples fluid flow in the fracture, represented with the lubrication approximation, to the geo-mechanical behavior of the bulk poroelastic rock, comprised of an elastic rock skeleton saturated with fluid. Fracturing fluid exerts traction on the fracture surface and is also allowed to leak-off into the poroelastic medium using a transfer function approach. Stress intensity factors (SIFs) are evaluated based on the Contour Integral Method, accounting for the fluid pressure on the fracture surface. The SIFs are used to govern a full 3-D evolution of the fracture. Verification of the model is performed for known behaviors for the poroelastic response and fluid flow in the fracture.

Jan 1, 2015

By N M. Player, R P. Varden, E Jones

"An effective geotechnical design provides an accurate and appropriate assessment, balanced with a mining company’s risk profile. Justifying the cost of slope assessment requires an understanding of the input sensitivities, and resultant risk, to achieve a slope of a required functionality. As a project progresses from Scoping to Feasibility, the geotechnical risk becomes better resolved through increased expenditure on drilling, testing, analysis and modelling as long as the input data is appropriately spatially distributed. Providing accurate and appropriate geotechnical assessments in the early stages provides confidence in all following stages, especially where initial analysis indicates difficult geotechnical conditions. It is also in the early stages of project definition that there is most opportunity to maximise the value of the deposit through investigations into optimal mining methods.This paper examines the advantages of geotechnical engineering input through a project study period. Early geotechnical involvement allows the Scoping and Pre-Feasibility Studies to be more effective. Operational risks can then be better understood and dealt within the Feasibility Study phase, also ensuring that the correct risks and management controls are put in place.With commodity price pressure and cost of resource recovery in a downturned industry, reducing the risk to cash flow, resource recovery and safety should be a primary goal for all mining companies. Reduced risk can be effectively achieved through geotechnical design of slopes to achieve a required performance as part of an integrated study to the Reserve definition and mine design.Citation:Varden, R P, Player, J R, Player, N M and Jones, E, 2016. Justifying Slope Design Risks and Costs, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 185–201 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By N. Vayenas, G. Yuriy

"The combination of a predictive reliability assessment model and discrete-event simulation can be an effective methodology to study the impact of equipment failures on the capacity of production systems in mines. In our case, a predictive reliability assessment model using genetic algorithms is combined with a discrete-event simulation model to analyze mine equipment systems.Discrete-event simulation involves modelling of real-life systems based on variables and events that occur or change at distinct points in time. The Simul8 simulation software, by Visual Thinking, is used in this research. It is a two-dimensional (2D), discrete-event simulation/ animation software tool for creating realistic depictions of manufacturing and materials handling systems.The simulation model developed for the purpose of this research represents a typical two-level, sub-level stoping section of an underground mine in the Sudbury region in Ontario, Canada. This 2D model was created to assess the impact of equipment failures to a mine’s production throughput. In more detail, using mean time between failures (MTBF) data of scooptrams derived from a reliability assessment model based on genetic algorithms, LHD failures are incorporated into the simulation model. These failures cause production interruptions to the development cycle and consequently loss of hauling capacity.Another purpose of this research work is to demonstrate how low-cost simulation tools such as Simul8 can be successfully applied to model underground hard rock mining operations. The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL)."

Jan 1, 2005

By W T. C Kendall, H D. Ngo

Garden Well is a shear-hosted Archaean orogenic gold deposit located 100 km north of Laverton, Western Australia. The Garden Well processing plant is designed for a nominal 491 t/h milling rate and annual capacity of 4 Mt. The plant has three key innovations:1. a scrubbing circuit, expected to reduce grinding power consumption by up to 20 per cent2. a secondary cycloning/gravity circuit, providing a second opportunity for gravity gold recovery (additionally, the circuit effectively increases the leach residence time of the coarse gold bearing fraction of the leach feed by approximately 60 per cent, without any additional tankage)3. the use of mid-stream oxygenation to enhance gold recovery.The Garden Well deposit is free-milling with overall laboratory gravity/leach gold recoveries exceeding 95 per cent at a P80 grind size of 150 ¦m. Three mineralogical domains have been identified: oxide, transition and fresh, with the fresh domain having subdomains of fresh ultramafic and fresh shale. There is a high component of gravity recoverable gold in all three domains.This paper will discuss these innovations and the design challenges and the risk mitigation strategies that were adopted to ameliorate the prototyping risk. The performance of the plant since commissioning together with lessons for the future will also be presented.CITATION:Smith, R J, Kendall, W T C and Ngo, H D, 2013. Treatment plant innovation at Garden Well, in Proceedings World Gold 2013 , pp 315-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J. D. Price, W. M. Bertholf

One of the chief difficulties with which the operator of a coal washing plant has been forced to contend is the handling of the very fine coal. First he has the problem of separating the fine coal from washery water. This is usually accomplished by the use of settling cones or Dorr thickeners: in either event the separated fine coal contains a high amount (40 to 80 pct) of water and, somewhat loosely, dependent upon the size of the coal particles present, may be known as sludge or slurry. His second problem is the satisfactory further dewatering of such separated sludge and/or slurry.

Jan 1, 1949