Search Documents

By Alexander J. Verstraeten

The design and construction of foundations for power transmission line towers present some special problems. This paper describes a system of design and construction for these foundations that was developed in Europe and has attained general use there because of its reliability and cost effectiveness. Transmission line foundations distinguish themselves by having to deal not only with compressive and lateral loads, but with uplift loads and, because of the wind (in some regions earthquakes), with dynamic loading. The construction of transmission line foundations distinguishes itself mainly in the great number of inaccesible locations involved, resulting in extensive geotechnical investigation and logistical problems in moving men, materials and equipment.

Jan 1, 1987

By George M. Fowler

DURING 1937 the subject of mining geology was probably given more attention and more mining geologists were usefully employed than at any previous time. Of the many contributing factors the most important were: (1) a higher degree of prosperity in many countries, (2) a. better understanding of geologic phenomena, and (3) the apparently diminishing reserves of several important minerals. Mining companies have come to look upon geology with a growing appreciation of its aid in the more effective exploration and exploitation of mineral deposits. Most of the larger and more active companies have one or more geologists permanently attached to their staffs and some have well organized and efficiently managed geological departments. Even the smaller companies, who feel they cannot afford to employ a geologist on a permanent basis, are seeking the advice of competent men in this field with increasing frequency. One of the most significant trends has been the growing tendency to base exploratory work on more thorough geologic studies instead of empirical "hunches,"on which so much off the work in the past has relied. Likewise, mining companies are apparently more willing to expend larger sums on the basis of geologic possibilities in a district.

Jan 1, 1938

By Leslie F. Sawatsky

Raw water import requirements for oils sands mines depends mainly on factors such as ore processing rate, ore material characteristics, tailings processing technology, tailings storage systems, process water storage operations, the phase of tailings production, and non-recoverable seepage losses from tailings ponds. These factors can be readily quantified to calculate raw water import needs. Nevertheless, mine water balance continues to be misunderstood by some regulators, stakeholders and possibly even mine operators. Confusion over consumptive uses has led to a focus on recycling which is not necessarily applicable to a closed circuit water management system. Some water conservationists focus attention on raw water intake rules instead of the technical decisions that control consumptive uses. Typical oil sands mine water balances for various types of tailings operations, are analyzed to illustrate the effect of controllable and uncontrollable parameters as well as major options that need to be explored for reducing water demand. Uncontrollable parameters including tailings fines content, oil content of ore, connate water, mine depressurization water inflows and surface water hydrology. Controllable parameters include storage operations, advance water supply ahead of mining operations, type of tailings operation, net tailings pond seepage losses, and tailings impoundment operations. Potential reductions of raw water supply rates may be obtained by providing greater on-site storage to attenuate fluctuation in water demand, advance water accumulation prior to mine start up, early commencement of CT operations, thickened tailings disposal and paste technology. Water conservation measures should be focused on reducing on-site process water storage and water content of tailings material.

May 1, 2004

By Frederick G. Clapp

SINCE oil journals commenced to feature the progress of Iraq pipe-line developments and since newspapers undertook to follow the discussions between a certain large oil company and an Asiatic nation, I have repeatedly been asked questions that are only answerable by setting forth the essential geographic and historical facts of concessions in that part of the world. In so doing effort will be made to correct erroneous statements made in various quarters: and mistakes herein are being kept as low in number as possible. Perhaps the best-known concession in the Middle East is the one of the Iraq Petroleum Co., covering the greater part of the portion of the kingdom of that name- lying east of the Tigris River. West of the stream is the concession of the British Oil Development Co., which takes in all presumed petroliferous areas in western Iraq. No other important oil concessions exist in that country, except for the lands of the Khanikin Oil Co., which operates in "Transferred Territories" on the border of Persia. East of and continuous with the Iraq fields are those of Persia where the Anglo-Persian Oil Co. holds the well-known D'Arcy concession comprising three-quarters of the country, omitting the five northern provinces. This is the only valid existing concession in Persia, so far as known, except certain old firmans that permit development at Semnan in central Persia and possibly also certain regional grants to a French banking syndicate in eastern Mazanderan Province.

Jan 1, 1933

By H. D. Hess, C. P. Mabie

This report describes in detail the results of petrographic research conducted on 21 phosphate ores representing important deposits in southwestern Montana , southeastern Idaho , and northeastern Utah . The ores are described and categorized by mineralogical and chemical composition , thermal behavior of organic carbon , and textural constitution . Descriptive and genetic classification schemes applicable to western phosphate ores are discussed ; results from related studies made of the collophane mineralogy are also presented . The latter studies were centered on determining unit - cell dimensions and CO₂ , P2O5 , and fluorine content of collophane concentrates of 11 high - grade phosphate- rock hand specimens selected solely for this purpose . On the basis of this investigation , operational methods have been developed for quantitatively describing textural and compositional features that are likely to be significant in determining the response of phosphate ores to conventional beneficiation treatments ; systems for classifying the ores in relation to these features have been proposed . Studies to date point out distinct textural and compositional variations in the western phosphates and illustrate their importance in determining optimum beneficiation procedure .

Jan 1, 1964

By Les Gutzwiller

Fan applications in the mining industry have changed during the last 70 years. In 1922, J.R. Robinson authored a technical volume entitled Practical Mine Ventilation. At that time, atmospheric control had only recently shifted from natural to mechanical. The large, mechanical draft fans that were used then were centrifugal. The fans ran at low speeds, about300 rpm. Most were steam-engine driven. In the late 1920s and early 1930s, mines became larger, increasing the pressure and volume requirements of the fan equipment. Axial fans were designed to run at much higher speeds (710 to 880 rpm) and were driven by electric motors. They were also smaller and less expensive to install than the cumbersome centrifugal units. However, changes in mining have resulted in progressively higher static-pressure requirements. So centrifugal fans are once again proving to be a good choice.

Jan 1, 1999

By A. Ismail

"The paper takes its material from three peat mining and power project feasibility studies sponsored by CANMET and conducted by Montreal Engineering Company Ltd. in the years 1976 to 1980. The role which peat may play in the Canadian energy prospectus is outlined, estimated and measured fuel peat resources are tabulated, and the economic and technical feasibility of mining peat for power generation is reviewed Recommendations are made for future work, and construction and disbursement schedules are developed for a combined peat mining and power generation project. The relationship between the mining of moss and fuel peat is discussed.IntroductionWhereas moss peat has long been produced in Canada, and exported for horticultural use , the underlying fuel peat has received little attention until fairly recently.In the seventies, however, the deepening oil crisis spurred Canadian interest in Irish, Finnish and Russian experiences in the utilization of fuel peat. Among others, Energy, Mines and Resources Canada had long been alive to the possibilities which indigenous peat offers, and in 1976 the Canada Centre for Mineral and Energy Technology (CANMET encouraged a proposal from Monenco to carry out a preliminary study and submit a report on the "" Assessment of Canadian Peat as an Alternative Fuel for Power Generation"". The report was submitted in April 1977. This was the first of a series of studies, and the authors of this paper were involved in its preparation.The escalating price of oil and the increasing problem of relying on its availability have combined to make alternative fuels more attractive. Peat, like other fuels previously uneconomic because oil was cheap, is now progressively gaining in viability. In addition to these factors, the utilization of peat has the following advantages: improvement in the country's balance of payments, by virtue of burning an indigenous fuel;creation of local employment for the mining of peat; improvement in land utilization;peat is a relatively clean-burning fuel, with low sulphur and ash contents."

Jan 1, 1980

By Guolin Zheng, Jian Pan, Deqing Zhu, Xianlin Zhou

"In ferronickel production, nickel oxide and part of the iron oxide are reduced to metal by agglomeration and smelting in blast furnace. Due to the physical and chemical properties of the laterite ores, a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality. In this paper, the process of pelletization of nickel laterite was developed, and some parameters to strengthen the pelletization of nickel laterite have been optimized. The results show that the compressive strength of fired nickel laterite pellet can reach over 2000 Newton per pellet while firing at the temperature of 1220 °C~1250 °C in 12 min. The product pellet can be used as high-quality burden for blast furnace to manufacture ferronickel.IntroductionIn recent years, the global stainless steel market was developed exuberantly, which greatly promoted the needs of the basic raw material of stainless steel smelting - metal nickel. Currently nickel sulfide ores are only 40% of global nickel reserves, but offer 60% of all the nickel production. However, with the deficit of resources, the nickel sulfide ore (high grade ore) is depleting, so there is an increasing focus on the utilization of low-grade nickel laterite. Recent research has focused on the wet treatment process to utilize nickel laterite, and less on the use of other technologies [1-8]. The economical and efficient technology relies on the reduction of nickel oxide and part of the iron oxide metal by agglomeration and smelting in blast furnace in China. Some domestic steel companies have adopted this process [9, 10]. Unfortunately a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality of fired pellets. In this study, the process of pelletization of nickel laterite was developed firstly, and some parameters to strengthen the pelletization of nickel laterite have been optimized, and the product pellet can be used to produce stainless steel and ferronickel alloy by blast furnace."

Jan 1, 2011

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

By Dale S. Preece

"Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control. Three-dimensional computational capabilities in terms of software, material models and computer speed have recently made possible the computer simulation of multiple blast holes in a bench configuration with precise delay timing between holes. Some of the key physical phenomena enabled by precise delay timing include: 1) collision and interaction of stress waves produced by adjacent blast holes, 2) reinforcement of stress waves from multiple holes as they reflect from the bench face and ground surface, 3) reflection of stress waves from “dynamic free surfaces” created by previously detonating holes, and 4) deformation induced fracturing, cracking and fragmentation. Simulating rock blasting in 3D has shed light on the physics involved and is resulting in an evolution of our understanding of fragmentation mechanisms. Routine use of these 3D computational tools will result in a much better understanding of the complex physics set in motion by the rock blasting process and allow predictionof improved blasting."

Jan 1, 2009

By Gerry Doeksen

The paper deals with three case studies: (a) the handling of wet concentrates (5 to 8 per cent moisture) through feed bins; (b) the handling of the same product in rail cars; and (c) the handling of dry concentrates (less than 0.5 per cent moisture) through feed bins. In each case, the paper discusses the problems of rat-holing. In each of cases (a) and (c), there is a discussion on the consequent extreme variations of feed rates coming from the feeders, making automation of process control difficult to impossible. Currently available bin-flow theory and flow property tests are used as aids in redesigning the bins. The paper concludes with illustrations of the final results after the redesigned hoppers were installed and tested. There is also a discussion on the advantages of the new mass-flow bins on adjacent feeder performance.

Jan 1, 1970

In recent years, Computational Fluid Dynamics, CFD, has been commonly utilized in the mining industry to model the fluid flow behavior in underground mine workings. This paper uses CFD modeling to simulate the airflow behavior in underground crosscut regions, where brattice sails are used to direct the airflow into these regions. Brattice sails are cost effective ventilation control devices for temporary or permanent use in underground mining. They can be used to deflect air into the unventilated areas such as crosscut regions. Their design and installation is a fundamental issue for maintaining a sufficient supply of fresh air and achieving effective air circulation and contaminant removal. At the same time, they should have little impact on the mine ventilation system. This paper presents the results of a two-dimensional CFD model, which examines the effects of brattice length on fluid flow behavior in the crosscut regions. The results of this study will assist in understanding the ventilation air behavior and in determining the optimum size of brattice curtain (sails), which provide a highly effective contaminant removal from the unventilated mine areas. This, in turn, helps the mine ventilation designers to meet the mine safety requirements.

Jan 1, 2009

By A. Butler

This paper explains the politics of mine nationalization in contemporary South Africa. Nationalization and privatization typically occur in the oil, mineral resources, and state utilities sectors, and they tend to follow one another in a long-term cyclical pattern. The paper explains why the current international environment has encouraged demands for nationalization and other forms of ?resource nationalism? in the South African minerals sector. It goes on to describe how the resurgence of resource nationalism has been influenced by internal factional politics in the African National Congress. It concludes that nationalization is unlikely to be the outcome of current policy deliberations within the ANC.

Jan 1, 2013

By T. Braun, J. Parker

On June 25, 1999, BHP Billiton (BHPB) announced the suspension of operations at the BHP Copper Inc.(BHP) San Manuel copper mine in Pinal County, Arizona. Subsequent to this announcement, BHPB aggressively pursued a number of alternatives for the underground mine and open pit facilities, including continued curtailed operations, sale to a qualified mining operator and closure of the property. After consideration of these various alternatives over a 2.5-year period, BHPB announced final closure of the mine site on January 15, 2002.This paper describes how the BHPB charter and HSEC policy apply during the closure process.

Jan 1, 2004

By D. Kachongo, Y. Cheng, A. Kashala, D. Samal, G. Mitshabu

Many copper processing flowsheets in the Democratic Republic of Congo include the leaching of oxide ores containing copper and cobalt, copper solvent extraction, copper electrowinning, and precipitation of cobalt salt. Recently, cobalt price gained momentum, driven mostly by the fast-growing electric vehicles battery market. The ore blending scenarios tend to prioritise high cobalt grade ore, whatever the content of copper and other impurities. Therefore, many copper solvent extraction circuits are running below design capacity. The variability of feed induces a variability of the leach solution with respect to copper, manganese, and silica contents. It is thus important to adjust hydrodynamic and metallurgical parameters of the solvent extraction plant to optimise metallurgical performance, production cost, and the quality of the copper electrolyte. This paper presents some results on how solvent extraction plant parameters have been managed in two solvent extraction plants running with lower than designed copper input. INTRODUCTION Referring to a report of the chamber of commerce of the Democratic Republic of Congo (DRC) the online publication Agence Ecofin (2019) indicated that the DRC ranks in the fifth position of the world top copper producing countries with over 1.2 million tons produced in 2018. The same year, 66% of the world’s cobalt was produced in the DRC at over 106,000 tons. If the political situation remained stable and the new tax regime introduced in 2018 did not deter private investors, copper production could reach 1.4 million tons/a in 2020 as pointed out in Mining.com (2019). Forecast figures for DRC cobalt production vary widely depending on analysts. The DRC online magazine Actualité.cd (2018) referring to a ministerial source forecasts over 141,000 t cobalt/a for 2020. The reality will depend on many factors, including the selling price, the supply compared to the demand, and finally the reaction of investors to the new DRC tax regime. The growing electric vehicle batteries market has been the major key driver of the price of cobalt. The five years historical cobalt price graph in figure 1 from infomine.com (2019) shows that the price of cobalt peaked at over 40 USD/lb in the first quarter of 2018. Cited by the online Magazine Creamer Media, Smith (2019) has indicated that the long-term demand of cobalt will likely remain strong.

Jan 1, 2019

By M. K. G. Vermaak

Spiral concentration forms a crucial part of gravity separation circuits. The application of process models in the operation of gravity separation circuits offers significant benefits in recoveries and grade control. Significant strides in the modelling of spiral concentrators have been made during the last couple of decades. Despite these advances in modelling techniques and models, application in industrial processes is not fully optimized. The adjustment of splitter positions to accommodate changes in the feed parameters is impractical and difficult, resulting in losses. In this work an optical method is employed to detect the concentrate band position as a function of operating variables. As expected, the results indicate a strong influence of the solids content and total heavy mineral (THM) feed grade on the predicted gangue-mineral interface. Viscosity modifiers indicated the band position to be sensitive to viscosity and therefore the slimes content. Validation on an industrial sample indicated the possibility of using this model in feed-forward control application.

Jan 1, 2008

By A B. Christie, R L. Brathwaite, A Swain

This study provides quantitative data on vein distributions within seven selected epithermal systems, four deposits hosted predominantly in rhyolitic rocks: Ohui, Wharekirauponga, Neavesville and Komata, and three major deposits mainly hosted in andesite: Martha Hill, Golden Cross and Karangahake. The technique of fractal analysis was used to help quantify vein distribution patterns. The fractal dimensions (D) obtained are related to the number of veins per metre, the degree of vein clustering, and vein thickness. An increase in any of these tends to increase the fractal dimension.   It is the relative relationship of these parameters that is important for the characterisation of vein distributions, and the comparison of different deposits. Within the same systems, the rhyolites are characterised by lower vein thickness and vein density, but have a higher degree of vein clustering compared to the andesites. Sections that are deeper and more centrally located within the epithermal system and/or close to major structures tend to have a greater degree of vein clustering, higher average vein thickness and density, and higher thickness to density ratios. This depth control is most pronounced in epithermal gold-silver systems because they have formed at shallow crustal levels where physico-chemical conditions change drastically both vertically and laterally. In addition to lithological and structural control at vein scale, deposit scale structure is of great importance in the deposition of economic mineralisation. Large open vein structures capable of sustaining high fluxes of hydrothermal fluid, favourable for the formation of large, high-grade gold deposits, are best developed in andesite sequences.

Jan 1, 1995

By Andrew Bamber

Between the early 20th Century and the present, the production of mined copper ore has increased from tens of millions of tonnes per annum to several billion tonnes per annum, an unprecedented increase. Contemporaneously, the average grade of mined copper ore has declined from over 2% to approximately 0.5%. Again, in parallel, the price of copper has increased dramatically to reflect the increasing cost of extracting and beneficiating such large amounts of low-grade ore. Within the period the copper price however exhibited several periods of intense volatility, driven by interrelationships between demand and supply, themselves strongly driven by periodic industry developments in the fields of exploration, ore extraction, mineral processing and extractive metallurgy. It is notable that these periods of intense innovation exhibit a strong correlation to preceding periods of price, demand or production volatility. This paper examines key trends in each theme between 1900 and 2018 and draws strong conclusions as to the interrelationship between them. INTRODUCTION The production of copper metal has increased from around half a million tonnes per annum to over fifteen million tonnes per annum over the course of the 20th Century. Contemporaneously, the average grade of copper ore mined has declined from over 2% to approximately 0.5% copper by weight. As a result, the volume of Run-of-Mine (ROM) copper ore required has increased from around ten million tonnes per annum to over a five billion tonnes per annum over the period, an unprecedented increase. The adage is that demand drives supply, that prices rise in times of high demand and/or short supply, and that prices fall when supply catches up with demand. The market sellers in biblical times knew this well; mediaeval market sellers equally. Dutch tulip sellers in the 1600’s experienced both in extremis — much to their dismay — and the great industrialists and early capitalists of the industrial revolution knew this also. Mining recently went through a cycle where investors and producers both believed that the “old” rules did not apply any more and that the industry was in a “supercycle” where prices would continue to rise on the back of increasing demand. However, as the GFC of 2008–2011 showed, this was not to be. Another adage says that we constantly innovate to lower costs of production. Is this true? Do we only innovate to lower cost? Has the true cost of producing copper actually gone down over the century? Or are there other balancing forces at play? Herb Kellogg, in his Centenary address to the American Institute of Mining Engineers (now SME), categorized two types of innovation: ‘Bigger and Better’, and ‘New Process’ (Kellogg, 1970). ‘Bigger and Better’ allows increased production at presumably lower cost; ‘New Process’ supports the same result at presumably the same scale, but at significantly enhanced efficiencies and (therefore) lower cost. It is suggested that both types of innovation are constantly and interchangeably required to achieve the kind of scale-up, at achievable operating and capital cost that the industry has achieved over the period. What can be shown, over this last Century and a bit, is that supply and demand are indeed inextricably linked, price and demand are linked, but so are price and cost of production. And the innovation required to sustain that weaves in between them all, cost-effectively increasing production capacity or lowering the cost of production at the same throughput, and sometimes both.

Jan 1, 2019

By F. -J. Wodopia

Sustainability of energy supplies has been an issue of general interest for a long time. Whilst in the past the continuous productive use of natural commodities was in the fore, its compatibility with the environment and climate and ultimately also social aspects have recently gained more and more attention. Today many discussions focus on the climate compatibility of individual options to act. Fossil fuels, in particular coal and lignite, are generally challenged because coal use makes a significant contribution to global man-made CO2 emissions. The drastic increase in the consumption of fossil fuels is not explained by the fact that coal utilisation technologies are not or cannot be sustainable but rather by the growing world population and the endeavours numerous national economies trying to catch up economically. Coal is the world’s No. 1 fuel and, in the view of many experts, will keep this position also in the foreseeable future. The access to its deposits plays a significant role for the economies of the emerging countries. Consequently the aspects of energy security and economic efficiency need to be considered at eye level with climate compatibility. In Germany, however, the public acceptance of fossil fuels and of large industrial projects is in the focus of attention.

Jan 1, 2011

By Enrique Rubio Esquivel, Matías Fuentes Bustamante

The transition from open pit to underground mining represents a key strategic challenge in modern mine planning. This paper presents a multicriteria and multivariable methodology to plan such a transition, integrating technical, economic, environmental, and social considerations. The proposed framework focuses on risk reduction (de-risking) through the identification of alternative development paths, the use of stochastic simulation to model geological and technical uncertainty, and different mining strategies such as methods, production rates, sequence, etc. for ultimate underground implementation. The study summarizes the limitations of traditional planning methods—which usually treat the open pit and underground mine designs as independent processes—, also often it considers a single mining method and production rate for the underground option. Instead it is proposed an integrated approach that leverages synergies between both mining methods and scalable production rates. Also the proposed methodology incorporates the definition of critical variables (geotechnical, economic, and social, among others), the construction of multiple operational and technological transition paths, and the evaluation of each path under criteria of economic attractiveness and practical do-ability (capacity to be executed). Using simulation tools (SIMPLAN for operational performance and SIMVAL for economic evaluation), probabilistic distributions of the different path are obtained, enabling the quantification of the project’s Value at Risk (VaR). A subsequent multicriteria analysis weights the expected profitability against the feasibility of execution of each alternative, producing a decision matrix that provides a framework for evaluating the different project path. As a result, the proposed approach identifies OP→UG transition strategies that maximize business value by capturing remaining resources while minimizing financial and operational risks. Finally, strategic conclusions and recommendations for the industry are provided, emphasizing the importance of early transition planning even challenging the open pit sequencing of the latest push backs by introducing early underground operations. Future work includes strengthening the methodology—such as integrating real-time analysis and adaptive decision-making—and providing recommendations for its application in various mining operations. In summary, this paper delivers a technical and professional framework to guide mining companies on when and how to carry out a successful transition from open pit to underground mining, balancing resource recovery with financial, operational, and social security.

Feb 22, 2026