Search Documents

Australia is a hub for mining technology development. The paper describes many of the key players involved in mining research in this country along with some of the interesting research outputs to emerge over the past decade.

Jan 1, 2010

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By Earle S. Burnett

This report outlines the experimental procedures for using a Burnett apparatus to obtain compressibility coefficients for multiphase, multicomponent fluid mixtures. The conventional Burnett method is described briefly whereby multiphase compressibility data can be obtained by first determining the compressibility factor, Z, as an isothermal function of pressure alone. Then starting at conditions of temperature and pressure where Z is known, the fluid is cooled at constant volume to some lower temperature at which the resulting pressure is measured, and a corresponding value of Z is obtained from a fundamental relationship between compressibility factors, pressures, and temperatures at constant volume. The isochoric treatment of the fluid, extended to still lower temperatures and along other isochors, eventually results in compressibility determinations for the whole two-phase system thus covered experimentally.

Jan 1, 1963

By Sydney H. Ball

It is a peculiar anomaly that while the world uses the term "rich as a gold mine" as the superlative figure of speech descriptive of wealth, the shares of gold mines are not as popular investments in America as certain of them should be. One of the most able of Manhattan's bankers is a director in an investment trust with a portfolio the value of which has gone the way of other such portfolios. Luckily a couple of years ago a few hundred shares of Homestake were purchased, and since then the trust has not only received therefrom satisfactory dividends but has benefitted from a large appreciation in their value. At each directors' meeting, however, the banker in question, Cato-like, suggests the sale of these shares, gold shares being, in his opinion, too speculative to be included in the portfolio of any trust. A short time ago the financial pages of one of our great metropolitan papers featured an article listing the corporations still paying dividends at the 1929 rate. Gold-mining shares were, the article stated, excluded, although in reality every gold mine on the New York Stock Exchange paid higher dividends in 1932 than in 1929. This 'Alice in Wonderland' treatment of the gold-mining shares is admittedly a bit confusing to those of us who believe that the shares of certain gold-mining companies have a rightful place in any well diversified portfolio. It should, however, here be recorded that whereas, fifty years ago, in America, gold-mining shares were considered by the public as instruments of nefarious gambling, now shares of the better gold mines are sought by astute investors. In England for well over a generation their value as sound investments has been widely recognized.

Jan 1, 1933

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By T M. Campos, J Silva, L M. Tavares, J Lichter, L P. Alves, B K. N Rocha, H D. G Turrer

The depletion of the richest ore deposits and the increase in number of mining projects involving deposits with complex mineralogy, higher competence and lower grade has led to an eminent need for improving understanding on multicomponent behaviour in mineral processing. One particularly relevant case is the ball milling of itabirite iron ores fed to the processing plant of Minas-Rio operation in Brazil. Dealing with the two main mineralogical components of the ore, namely hematite and quartz, the operation faces some challenges to improve understanding on how the two components behave in the process. Mathematical models have showed potential to give support in this task, but its applications to describe this type of industrial-scale grinding is still missing. The present work demonstrates the application of a multi-component ball mill model to simulate a closed ball mill circuit with hydrocyclones using the commercial software Integrated Extraction Simulator (IES). Model was calibrated on the basis of bench-scale tests and industrial surveys. Multi-component simulation results are then compared to those considering a single component in the feed, demonstrating the value and great insights that can be achieved by using the former in optimising plant operation.

Aug 24, 2022

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By P. Amelunxen

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan?s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By Jeffrey H. Welsh

This report presents a study on the use of computerized, continuous remote monitoring systems for fire and explosive atmosphere safety in underground coal mines. The effects of these systems on the safety level in mines are investigated, and the relationship between mine safety regulations and computerized, continuous, remote monitoring is analyzed.

Jan 1, 1982

By M. S. M. Aljuhani

In this paper, one of the human factors that affect productivity in an underground gold mine in Saudi Arabia was investigated and analysed for the purpose of improving productivity. The human factor that was investigated is labour utilization and labour productivity. In the selected mine, labourer?s performances were measured carefully. It was found that in this mine, workers spend only 65% of the shift time in a productive work, and they spend 35% of the shift time in non-productive activities. As a result, recommendations were presented to enhance productivity in the selected underground gold mine by enhancing labour utilization.

Jan 1, 2002

By F. Burat

Large reserves of feldspar ore exist in the Aegean region of Turkey. The main colored impurities in these ores are iron- and titanium-bearing minerals such as anatase, rutile, sphene and ilmenite. In this study, a potassium feldspar ore containing mainly quartz and coloring impurities was subjected to beneficiation tests involving magnetic separation and flotation, which were applied either separately or in combination. Bench-scale flotation experiments using cationic collectors G-TAP and Flotigam V-4343 and using HF and H2SO4 as modifiers were employed to separate feldspar from quartz and to remove part of the titanium impurities. The best results were achieved with a combination of high-intensity wet magnetic separation and flotation. A feldspar concentrate containing 16.28% Al2O3, 10.75% K2O, 2.84% Na2O, 69.97% SiO2 and 0.16% Fe2O3 was produced. A quartz concentrate containing 2.30% Al2O3, 0.48% K2O, 0.42% Na2O, 0.07% Fe2O3 and 96.20% SiO2 was also obtained

Jan 1, 2007

By Forrest T. Moyer

The safety record of the coal-mining industry, both anthracite and bituminous, in 1966 was improved over that of 1965 in all general measures of injury experience. The improvement was more pronounced in the anthracite industry. The total of 10,679 disabling work injuries comprised 233 fatal and 10,466 nonfatal injuries, 26 and 692 fewer, respectively, than in 1965. The number of fatalities in 1966 was the lowest annual total since complete records were started in 1910. Similarly, the number of nonfatal injuries in 1966 was lower than in any year since 1930 when such data were first collected.

Jan 1, 1969

By Satyajit Vaidya, Rudolph Frizzi, Luis Berroteran

This paper presents design and construction challenges associated with a high-capacity rock-socketed drilled pile foundation system for a 60-story building recently constructed in an urban environment. The site is in very close proximity to surrounding 1-to-6-story buildings and a commuter rail subway tunnel structure. High compression, uplift, and lateral loads imposed by the tall, slender tower constructed over a relatively small site footprint posed a significant design challenge due to the close proximity of the subway tunnel and other structures. Construction challenges included those associated with advancing the drilled pile casings through overburden materials using internal flush method mandated by the Transit Agency, advancing the casings through very dense glacial till materials encountered above top of rock, and drilling rock sockets in variable rock conditions. This paper provides a brief overview of the site and subsurface conditions, and discusses the resulting design and construction challenges for the drilled pile foundation system and how they were addressed. SITE AND SUBSURFACE CONDITIONS The 8,350-square-foot site is located in a busy neighborhood in downtown New York City (NYC). Buildings neighboring the site are supported on shallow foundations, and their basements extend about 15 feet below the sidewalk level. A NYC-Landmarked building is located within a NYC Department of Buildings (DOB)-designated 90-foot influence limit from the Project site. NYC Transit Authority (NYCTA) subway tunnel and station structures are located in close proximity to the Project site. The subway tunnel structure extends about 50 to 55 feet below the sidewalk level. Although the upper portion of the tunnel structure is about 13.5 feet away from the site property line, the lower portion is only about 1 foot away from the property line. A site location plan is presented as Fig. 1. Geotechnical borings revealed subsurface conditions generally consisting of successive strata of surficial fill, sandy and silty soils, and glacial till (predominantly consisting of cobbles and boulders) overlying mica schist bedrock. A generalized subsurface profile is presented in Fig. 2. The surficial fill stratum was about 10 to 23 feet thick, and generally consisted of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick. The underlying sandy and silty soil stratum was about 60 to 79 feet thick and generally consisted of loose to medium dense inter-bedded layers of fine to coarse sand, silty fine sand, and silt. The underlying glacial till stratum was about 26 to 70 feet thick and generally consisted of cobbles and boulders embedded in a very dense soil matrix. Top of bedrock was encountered in the borings about 110 to 150 feet below sidewalk level. Groundwater level was measured at about 30 feet below sidewalk level.

Jan 1, 2018

By RUSSELL C. FLEMING

GILSONITE is a brilliant black, tarry-like bitumen, classed technically with glance pitch and graharnite as an asphaltite. As found it is brittle, breaking much like ice, and has a conchoidal fracture. Purest forms are used in the manufacture of paints, varnishes, electrical irisulatiorl, and inks for rotogravure; molded articles such as switch handles, telephone mouthpieces, and but- tons are made from the intermediate grades, and the poorer grades are used for the saturation of felt. According to the U. S. Bureau of Mines figures, production grew from about 4000 tons mined in 1904 to 55,000 tons in 1929. This asphaltic substance is found only in the Uintah basin in northeastern Utah, in veins over a wide area. Veins in the vicinity of Fort nuchesne were first discovered about 18G2, on what was then the Uintah Indian reservation, and the vein matter was originally called Uintaite because of that fact, In the early days, S. H. Gilson. of Salt Lake City, was so persistent and zealous in his efforts to develop the deposits and find a market that the name gilsonite was given to the material. Later, the wider and more renowned wins near Wayson and Dragon, in extreme eastern Utah, became the main supply.

Jan 1, 1932

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008

By M. A. Cristovici

"In the last few years CANMET has taken the initiative by investigating the possibility of reactivating abandoned old tailings dumps (for gold production) which would be of potential economic interest across Canada.Nova Scotia was one location where numerous gold processing plants were in operation in the early days. A survey of the old tailing dumps was conducted and some areas of interest were selected. Among them were the sites identified as Lake Charlotte and Forest Hill.Ore samples collected from those tailing ponds were examined for their chemico-mineralogical composition and investigated for gold extraction. Three technological concepts were tested: flotation, direct cyanidation and flotation followed by cyanidation of the flotation concentrate. The combined flotation- cyanidation variant, yielding a gold recovery in the range of 90%, was recommended for processing the tailing ore.Pilot-plant runs carried out by a commercial testing firm (data not included in this paper) confirmed the conditions and results of CANMET's technology.As a result a consulting-engineering firm designed the processing plant which is expected to begin operation in the near future.IntroductionIn the last few years CANMET initiated a research program to locate in Canada, abandoned gold-silver tailing dumps of potential economic interest and to explore the possibility of recovering the precious metals from these old deposits by modern techniques.A literature search revealed that the first production of gold in Canada was recorded in British Columbia in 1858 and that, production prior to 1900 was essentially restricted to the Yukon, British Columbia Nova Scotia and Quebec. During the early 1900s, Ontario, Manitoba and the North West Territories joined the ranks of the gold producers.Early milling and recovery methods were mainly restricted to sluice boxes, gravity stamps and amalgamation. Froth flotation and cyanidation were introduced at about the turn of the century.Recovery of gold at plants using flotation and cyanidation was very good, therefore the tailing ponds resulting from those operations would, very likely be of little or no economic importance. However, the gold recovery at the amalgamation and gravity concentration plants appeared to be lower, indicating the possibility that significant amounts of recoverable gold would have been carried with the tailings to the dump sites."

Jan 1, 1986

By P. Bousquet

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian mining industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (e.g., pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2002

By D. M. Jepsen

One of the first things we tell a potential new client is that they have only one chance to make a first impression with an Aboriginal community; all future communications and engagement will be predicated on that first impression. The key components of this most critical meeting are not your power point, your maps, or your draft plan for development ? they are instead a genuine, evident and clear demonstration of a sincere desire to develop a positive relationship that is based upon respect, and consideration and understanding of local communities and their interests, needs and desires. Relationship building is the foundation of proactive and positive consultation and accommodation with Aboriginal communities and the tone is set with the first meeting. C3 has refused more clients than we have accepted due most often to the fact that relationships between the company and the Aboriginal community have already devolved into a tense and toxic scenario. Land access and tenure certainty for exploration and mine development is critical to the foundation of a healthy, sustainable and environmentally and economically sound mineral exploration and mining sector. Without certainty confidence to invest in mineral exploration will be severely eroded. We all understand that substantive investments in exploration are required to increase the possibility of discovering, defining and developing new mines. The development of positive relationships based on a shared commitment of understanding, mutual respect and trust by Aboriginal Peoples and the mineral sector can provide the required business certainty and deliver social and economic benefits for local Aboriginal communities.

Jan 1, 2012

Now a new generation of computerized drill rigs has been launched and they are based on modern standard PC-computer technology. The rigs have been well embraced by the market and more than 100 units have left the assembly line. The new generation has taken a quantum leap forward with respect to drilling accuracy, logging capabilities, reduction of manpower in some types and serviceability compared to the previous generation of drill rigs. The Can bus technology, well proven in the automobile products, is the backbone in the new generation control system of Atlas Copco. The short-term development is now focused on establishing this new automation platform on other product lines of Atlas Copco products. The long-term objectives is to offer the mining industry Atlas Copco products with one common automation platform. Essential for Atlas Copcois to contribute to the work with the on-going Data Exchange standard between mining machines and mining computer systems (IREDES). Our belief is that an accepted standard will make mine automation programs affordable for a wider base of the mining industry, because of the possibilities to a cost effective integration of different equipment with a minimum of system integration problems and machine specific interfaces.

Sep 1, 2001