Search Documents

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network, and 2)development of , set of digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the model; and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated for their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

By D. D. Southworth

In 1987, the Bureau of Mines initiated a mineral assessment of the 5.7 million-acre Valdez Creek Mining District (VCMD). Following a literature search and interviews with persons knowledgeable about deposits within the district, limited on-site field visits were made to various deposits. Present within the district are the industrial minerals limestone, argillite, granite, basalt, perlite, zeolite, and sand and gravel. At least six limestone deposits of potentially economic size and grade are known to exist within the district. Adjacent to the Parks Highway and marginal to the district, a limestone deposit is currently being mined as a source of agricultural lime. A perlite occurrence near Yacko Creek was evaluated but proved not to be of industrial grade. The sand-and-gravel resources of the district are vast, but high silt content renders many of the glacial deposits unsuitable for use in construction applications.

Jan 1, 2011

The Arctic is a region of special economic, geopolitical, research, socio-ethnic, and defense interests of both Russia and other countries of the Arctic zone. Introduction of innovation technologies at ore-processing factories is a direct responsibility of the state and this problem should be solved on the basis of coordination of interests of different stakeholders. The task of elaboration of scientific principles of rational state regulation in the North is very topical. Innovations require considerable investments first of all from private capital. However as an investment object innovations are not attractive for investors as they require large expenditures for long-term projects, and they are connected to high risks because market incentives form striving to get quick profits of private companies and result in a certain behaviour strategy while innovations need ?long money?. Under such conditions without state regulation of investment and innovation activities development of the mining sector in the Arctic practically has no prospects. At innovation development of mining enterprises economic growth is provided at the expense of active state innovation activities. The elaborated strategy of ore-processing enterprises should correspond to the modern paradigm of the ore-processing industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the AZR which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents. The main principle of creation of innovation technologies is to obtain more products of higher quality with minimal costs. This allows increasing ?productivity of the resources? several times. This principle makes increasing productivity of the resources the most important and in this case efficiency of use of the resources brings extra profits at the expense of lack of new costs such as payment for protection and utilization of wastes. According to the economic theory only ratio between demand and supply is able to fix optimal proportions in economy and to give necessary signals for investment activities of mining enterprises. In this context market for minerals and increase of mineral resources productivity do not create incentives for investment activities without which neither sustainable economic growth nor solution of macroeconomic tasks are possible. Nevertheless countries should not reject this idea in spite of economic efficiency of the enterprises. Extraction degree of useful components and especially oil in the Arctic zone is one of the lowest in the world. This can lead to crisis of oil industry and other mining sectors. The reason for that is lack of a state policy of realization of innovation technologies in the mining sector in the Arctic.

Jan 1, 2014

By Chu Yong Cheng

Manganese is one of the main impurities in the recovery of base metals from their ores. This is especially true when laterite ores are processed using the pressure acid leach (PAL) process. The use of intermediate precipitation, solids/liquid separation and re-leach in the three Western Australian nickel laterite plants to separate nickel and cobalt from manganese and other impurities makes these processes complicated and costly in capital and operation. The research work carried out by the solvent extraction (SX) group at the A J Parker Cooperative Research Centre for Hydrometallurgy (CSIRO Minerals) has led to the development of direct solvent extraction processes to separate nickel and cobalt from manganese and other impurities. The simplicity of the process flowsheets and the expected savings in capital and operating costs are the major advantages of the new direct solvent extraction processes over the existing processes. By using a new synergistic organic system, Versatic 10 / dccyl-4-pyridinccarboxylatc ester, with a pilot plant leach solution from BHP¬Billiton (after iron precipitation), the metal values (Ni and Co) together with zinc and copper were separated from manganese and other major impurities (Mg, Ca and Cl) in the first SX circuit. The co-extracted manganese, magnesium and calcium were easily scrubbed out. The extraction and stripping kinetics of the metals with the new synergistic organic system were very fast and the synergistic system was found to be chemically stable. pH-extraction isotherms of metals with D2EHPA showed that the extraction order as a function of pH50 was Zn2+ > Ca2+ > Mn2+ > Cu2+ > Co2+> Ni2+> Mg2+. Semi-continuous test work with a cobalt pilot plant leach solution from Peko Rehabilitation Project Pty Ltd and a synthetic solution to simulate a concentrated laterite leach solution from BHP-Billiton showed that manganese, together with calcium, copper and zinc can be separated from nickel, cobalt and magnesium. This led to the development of another direct solvent extraction process to separate manganese and other impurities from nickel and cobalt and to recover nickel and cobalt from leach solutions. A project was initiated by HiTec Energy Ltd to recover manganese from waste laterite leach solutions using SX technology and to further purify it to produce high purity electrolytic manganese dioxide (EMD) for the high quality alkaline battery industry. Batch tests were conducted to select a suitable organic system for the extraction of manganese in terms of selectivity and extraction and stripping kinetics. A total of eight organic systems were tested using waste laterite processing solutions. A Versatie 10 / synergist system showed very promising results. By using the synergistic system, high manganese recovery would be obtained, fewer SX stages would be required and a higher A:O ratio could be used in extraction, resulting in a smaller organic inventory and lower capital costs. The risk of gypsum formation is also minimised with the synergistic system. Keywords: Solvent Extraction, Manganese, Laterite, Synergist

Jan 1, 2004

By A. K. Snelgrove

Introduction ?Concerning the inland commodities, as wel to be drawen from this land (Newfoundland) there is nothing which our East and Northe.rly countries of Europe doe yeelde, but the like also may be made in (ît) as plentifully by time and industry : Namely, rosen, pitch . . . metalls, and many moe. All which the countries will aford, and the soyle is apt to yeelde ... For besides these alreadie recounted and infinite moe, the mountains generally make shew of minerall substance : Iron very common, lead, and somewhere copper. I will not auerre of richer metalls: albeit ... more then hope may be concieued thereof. " - Narrative of Captain Hayes, second-in-command to Sir Humphrey Gilbert's Expedition, IJ83 (From Hakluyt). The investigations set forth in the following pages were made in the field in Newfoundland during the summer of 1927, and later in the laboratories and library of McGill University, and in the library of the Canadian Geological Survey at Ottawa, with the purpose of collating and adding to our knowledge of the geology of an area roughly wedge-shaped in outline, and nearly nine thousand square miles in extent, stretching across the centre of the island of Newfoundland, from the southwest to the northeast coasts. To the description of this district, which contains most of the known mineral occurrences of Newfoundland, the term mineral belt is here introduced.

Jan 1, 1928

The Shortage of Mining and Metallurgical Engineers I N many parts of the Western World attention has recently been drawn to the acute shortage of mining and metallurgical engineers produced by the universities. Naturally, the reasons for this shortage have been discussed, and various remedies for it have been proposed. In this paper, I want to examine some of them. It is now fairly generally ac-cepted among mining men that the easy attractions of modern urban life have left the career of mining in the metaphorical as well as in the literal backwoods. The industry finds it increasingly difficult to recruit adventurous and intelligent young men; for such men now seek their intellectual, if not physical, adventure in more glamorous occupations from a safe social base in suburbia. The salaries, opportunities and security offered by the mining industry do not complete effectively with the rewards offered by other industries and by commerce, taking into account the social disadvantages of a mining life. The excitement and other non-material attractions of mining

Jan 1, 1965

By Sara J. Davenport, Genevieve Morgis, J. J. Forbes

"This circular is part III of a series of papers reviewing the literature on air conditioning in mines, with particular reference to the health, safety, and efficiency of miners.4/ It deals with theoretical and practical methods of conditioning air in mines to correct or alleviate the health hazards described in parts I and II and discusses the results attained by some of the systems now in use in various-parts of the world.The principal conditions to be corrected or alleviated are the chemical qualities of mine air (especially when contaminated with toxic and noxious gases and dusts) and the physical qualities (abnormal mine temperatures and humidities) that emanate from various sources in underground workings. Air motion and barometric pressure are physical qualities also to be considered.From the standpoint of health, knowledge of the composition of the air, or atmosphere, in mines and other underground operations is of prime importance. Suitable control measures or plans of procedure to combat or eliminate the hazards from contaminants must be based upon accurate information obtained by the selection and use of proper methods of sampling and analyzing mine atmospheres (1).5/Conditioning air is one of the most essential factors to be considered in any underground workings, not only from the standpoint of health and safety but also with regard to efficiency and productivity. Without modern air-conditioning, the war's great demand upon the copper mines could hardly have been met, as the mechanical refrigeration cooled off sweltering holes in less than a month, whereas in the past it was standard practice to blow air through the tunnels for 3 years or so until they were cooled.This paper discusses methods of determining the chemical and physical qualities of mine air and their control. Briefly, the following points are presented:"

Oct 1, 1949

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By W. B. Berwald

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gras association, has been studying actively for the past several years the problem of the flow of natural gas through high-pressure transmission lines. Numerous data on gas flow through pipe lines under many conditions of operation have been obtained by carefully conducted tests, and these data, together with all other available information, have been analyzed carefully to secure practical facts for the use of operators in designing pipe lines and determining the effects of different operating conditions on pipe-line capacities. The first procedure in initiating; this problem was to review, compile, and analyze all of the existing data on the flow of natural gas through pipe lines. Actual data applicable to pipe and operating conditions normally used in the transmission of natural gas were meager, and the several pipe line flow formulas developed by different investigators gave widely varying; results when applied to problems of pipe-line design. Therefore, further experimental work under conditions comparable to those found in transmitting natural gas was essential before any definite recommendations could be made.

Jan 1, 1931

By W. B. Berwald

The United States Bureau of lanes, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the problem of the flow of natural gas through high-pressure transmission lines. Numerous data on gas flow through pipe lines under many conditions of operation have been obtained by carefully conducted tests, and these data, together with all other available information, have been analyzed Carefully to secure practical facts for the use of operators in designing pipe lines and determining the effects of different operating conditions on pipe-line capacities. The first procedure in initiating this problem was to review, compile, and analyze all of the existing data on the flow of natural gas through pipe lines. Actual data applicable to pipe and operating conditions normally used in the transmission of natural gas were meager, and the several pipe line flow formulas developed by different investigators gave widely varying results when applied to problems of pipe-line design. Therefore, further experimental work under conditions comparable to those found in transmitting natural gas was essential before any definite recommendations could be made. The problem, as originally planned, included flow tests on pipe lines in operation, and in each test the measured delivery vas to be compared with the delivery calculated from several common pipe line flow formulas.

Jan 1, 1931

By J. Perlacia

"As the bulk handling sector continues its transformation to Industry 4.0, the mining industry, and its harsh working and environmental conditions, provides a perfect spot to study the feasibility of remote analysis and maintenance of the components used for bulk handling. The most important and expensive tools have been adapted to the digital era in recent years, from remotely controlled haul trucks to monitored conveyor belts.However, the big items of the installations rely on smaller parts that have been leftaside, mainly due to the difficultyof adapting them to the Internet ofThings (IoT).The paradigmatic example is the lack of monitored rollers, while all the other components of the conveyorbelt installations (the belt itself, motors, drums, etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stoppage of the entire conveyor, due to possible damage to the belt. Thus, the implementation of an integral monitoring system of all the components of the conveyor is a must.The research and development department of ULMA Conveyor Components has been working since early 2012 on the development of monitored rollers, testing all the problems until their final installation in different demanding conditions, from the extreme heat in Australia to the freezing cold of Norway. All the tests have been done under actual working conditions, in real installations and have provided valuable knowledge in the identification of problems, their solutions and the final advantages of a roller monitoring system.Background and current stateThe malfunction of a single roller in certain conveyor belts can force the standstill of the entire installation until its replacement, due to the risk of greater and more expensive failures, such as a rip in the belt. In the case of a bulk handling installation, where a continuous supply of material is necessary, an unexpected stop of one hour could result in huge economic losses."

Nov 1, 2019

By Jo Katembo, Patty Bwando, Patient K. Ilunga, Yves Kalubi, Emman Mulaj

"From 2010, the dolomite concentration in the ore fed to the Usoke Plant increased, resulting in a significant increase in the gangue acid consumption and Mg build-up in the circuit, and thus an increase in the Mg:Co ratio in the plant solutions. This affected the Co salt grade, reagent consumption, filtration and drying capacity. Efforts were put in place to minimise the acid consumption and consequently the Mg dissolution (such as use of pre-diluted acid), but the benefits were negligible. Various efforts were then initiated by CHEMAF to improve the cobalt plant productivity (quantity and quality) by process changes, dual precipitation and seed recycle. The positive results obtained in the laboratory were successfully implemented on plant scale. A change in the process from a single-stage precipitation with Na2CO3 to dual precipitation using a combination of Na2CO3 and NaOH improved the capacity of the Co salt filtration by 30%, the Co salt grade and drying capacity by 50%, and reduced the reagent consumption by 22%. Implementation of precipitate seed recycle increased Mg rejection by 40%, improving the Co salt grade from 20% to 25%, and yielding a further drop in reagent consumption. INTRODUCTION CHEMAF (Chemicals of Africa), a mining company located in Katanga province of Democratic Republic of Congo (DRC), has been operating since 2003. The Usoke hydrometallurgical plant treats the Cu-Co ore from the Etoile pit to produce Cu cathodes via a leach–solvent-extraction (SX)–electrowinning (EW) circuit and Co salt via a selective precipitation process. The plant was designed to treat run-of-mine (ROM) ore grading 6% Cu and 1.5% Co; but, in 2008, due to a decline in grades, a heavy-media separation (HMS) plant was commissioned to enrich the low-grade ROM (3.5% Cu and 0.5% Co) up to 8% Cu and 1% Co before feeding it to the hydrometallurgical plant. Co is recovered by precipitation of Fe and Al with limestone, followed by Co precipitation as Co carbonate using sodium carbonate (Na2CO3), also known as soda ash. 85% of the final effluent from cobalt precipitation is recycled back to the plant as process water; the balance, 15%, is bled out and compensated for by fresh water top up to control and retard the rate of sodium sulfate build up."

Jan 1, 2015

By K. S. Olson

My reaction when first asked to present this paper was; "What could I possibly say that would hold the audience?s attention for 15 minutes? What could I offer that anyone familiar with the Nevada Barite Industry wouldn't already know?" Well, quite frankly I can't. The industry has certainly been anything but exciting for the past 10 years and, in fact, quite depressing. The challenge, for those few of us left in it, has been to keep it alive. At times it has felt like a doctor must feel with a terminally ill patient. All I can do is recap the past ten years, review the present state of the industry, and offer a few personal opinions and observations as to where I think we are headed.

Jan 1, 1993

By F. F. Aplan

Mineral processing engineers have recorded an- other year of active research and development work. Most gratifying was the broadly based attendance at the Mineral Processing Fundamental (formerly Basic Science) Committee sessions at the 1968 Annual Meeting of the AIME. Because of the availability of good papers, the active discussion and the growing attendance, sessions have grown from one to three at the annual meeting. Prof. M. C. Fuerstenau of the University of Utah will chair the Mineral Processing Fundamentals Committee for the next two years and we may thus be assured of continued active leadership. The name change from "Basic Science Committee" to the more descriptive "Mineral Processing Fundamentals Committee" approved by the MBD executive council is a welcome improvement. Our profession continues to attract the interest and cooperation of those in other professional groups. The 1968 Engineering Foundation Particulate Matter Conference, under the chairmanship of John Karpinski of Bethlehem Steel, was devoted exclusively to comminution this year. It attracted conferees from five continents and served as a particularly stimulating source of interchange of knowledge from many technical fields. Next year's conference will be under the chairmanship of Professor L,. G. Austin of The Pennsylvania State University. This conference plus the Symposium on Wettability and Flotation to be held at the annual American Chemical Society meeting in Minneapolis in April indicates the success achieved in the inter-disciplinary approach to problems. Other evidence of this spirit of professional cooperation is the forth- coming book on Size Reduction edited by D. W. Fuerstenau. This is the outgrowth of an AIChE symposium on size reduction held in 1965.

Jan 2, 1969

By Allan F. Lawrence

"I AM SURE you do not expect from me any learned dissertation on the problems and opportunities of the mining industry. Y our program committee must have recognized my limitations when issuing the invitation to speak to you, because they very thoughtfully left the subject wide open.With the leeway thus granted, I hope that you will bear with me for a few minutes while I try to clarify the impressions of the mining industry that I have gained in the very short time I have held the Mines portfolio and some of the parts that government bas or should have in furthering its development.As I see it, it is the duty of the Mines Department, as an arm of the provincial government, to balance the proprietary rights of all the people against the interests to whom the privilege of developing our resources are, in a s e n s e, leased. To strike a fair balance is not always easy, nor is it possible always to satisfy both sides. Still, under the free enterprise democratie form of government to which I think we al! subscribe, no better way of handling the problem has yet been discovered."

Jan 1, 1968

By D David

Amongst those whose task it is to design tumbling mills and other comminution machines there is an almost religious divide between devotees of the Bond method and devotees of other methods developed in more recent times. For a decade or so the issue was between the Bond power-based methods and the JKMRC (JK) simulation based approach. The newest method to challenge the status quo is power-based and was developed by Steve Morrell. As the title suggests, this paper will take some liberty at concluding that Fred Bond and Steve Morrell may be separated by history, but not by their approaches to their individual contributions to the science of comminution. Another driver for the paper is that although it is good to have diversity of thought, the existing divisions are problematic for those of us signing public disclosure documents. If alternative design methods produce materially different outcomes for the mill duty, then at least one of them is wrong or being used incorrectly. At some point the unsustainable argument may need to be put in a court of law that we metallurgists have two or more materially different design methods, each of which is correct! Therefore, perhaps a resolution is needed before this occurs?The works of both Fred Bond and Steve Morrell are each directly related to their contemporary grinding mill design and operational environments. Both their approaches are empirical, borne of observing and measuring real world situations. Both worked with theories that preceded them, gathered their own data and then each saw shortfalls in the status quo.Fred Bond was an escapee from revolution, a victim of The Great Depression, and had several near death experiences during his early site-based career. Perhaps he was fortuitously rescued from himself when asked by Allis Chalmers (A-C) to set up its rock testing laboratory in Milwaukie in 1930. Fred’s testing led him to conclude that neither the Kick nor the Von Rittinger theories explained his measurements. His writings on the failings of these old theories caused a divide between devotees of the old and new methods at that time. After many years, and much thought and plotting of data (the old way!), he came up with his now-famous equations (and his Third Theory) which have stood the test of time, certainly in the world of Bond-era machines.Coming from England via several African diamond mines, Steve Morrell immersed himself into the comminution world of the JK in Brisbane about a decade after Fred passed on. The JK had developed its semi-autogenous grinding (SAG) simulation framework using its own pendulum breakage tester, itself a derivative of the twin pendulum impact device invented by Bond decades earlier. At the JK Steve developed his authoritative Tumbling Mill Power equations and was involved in real world analysis of comminution problems on the global stage. Steve’s JK experience coincided with the demise of the rod mill, the rise of autogenous grinding (AG) and SAG milling and a rapid expansion in concentrator capacity.Morrell left the JK to pursue his own interests, which included ongoing consulting work, now demanded by the comminution world. He then turned to investigating a growing list of discrepancies between the opinions of designers and theoreticians, and the factual outcomes. The Morrell Method of design arose from this re-examination of ore testing, real world operating data and these glaring and expensive discrepancies between design and outcome. The elements necessary for a relook at the world of rock breakage were in place!CITATION:David, D, 2017. Steve and Fred would have been mates – a comminution design evolution story, in Proceedings MetPlant 2017, pp 2–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979

"Guests and Members of the Rocky Mountain Coal Mining Institute: "It gives me a great deal of pleasure to call the Fifty-Second regular meeting to order this morning. "I think that you will agree with me that we have an excellent program planned for the next three days, comprising various interesting and educational subjects by authors of prominence, which will be of keen interest to all of us in the coal industry. "The Program Committee, chairmanned by John Peperakis, has done an excellent job in securing this very splendid talent for our convention. "I would like to say a word as to the, condition of the coal industry in our part of the country as well as elsewhere. I believe we can look at it with more optimism than in the past several years, particularly in the state of Colorado, with which I am more familiar. "Annual coal production in Colorado gradually dropped from around 12 million tons during the years of World War I to as low as 8 million tons during the last war, and to less than 3 million tons in the year of 1954. We believe that it touched bottom that year, as in 1955 the state production went up again to nearly 3,400,000 tons, equivalent to an increase of 15%. As you know, the national increase in bituminous coal production for the year of 1955 was roughly 2000 over 1954. "The national increase for the first two months of 1956 over the same period of 1955 is approximately 2100. Colorado's production is running around 1000 over the comparable period of last year, and the 5 states represented by our Institute came up with a nice increase in 1955 over 1954 of 1000. "Figures on the increase so, far in 1956 for this group of states are not readily available, but I fully believe that. our industry locally, as well as nationally, is now starting out on a steady rise despite the fanfare of nuclear energy and its more glamorous competitor, solar energy. Many authorities tell us that real competition from these sources is a long way off and that the atomic energy program will consume far more coal than is displaced by nuclear power. "I do not mean to infer that we coal people are out of the woods by a long way' so far as holding and regaining markets, for our coal. The captive operators, which are well represented here, have not lost their market for coking coal, since coke is still a necessary

Jan 1, 1956

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining Co.'s Granite Mountain shaft. How this insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the lire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest pro¬ducer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By Ava Segal, Doga Cagdas Demirkan, Abhidipta Mallik, Sebnem Duzgun, Andrew J. Petruska

Search and rescue operations in mining heavily rely on humans. In the context of emergency situations within underground tunnels, the potential to utilize sensory technology for navigation assistance holds the promise of saving human lives. Our research introduces a device configuration designed to enhance the performance of search and rescue teams. This setup integrates LIDAR and thermal cameras with the Microsoft Hololens, facilitated by the NUC computer and ROS Bridge. Performance assessment involves quantifying the extent to which a user is willing to venture into a light-deprived section of the mine prior to necessitating supplementary illumination. The preliminary outcomes highlight the significant potential of augmented reality assistance in offering indispensable aid to first responders, thereby greatly augmenting the efficiency of search and rescue missions conducted during critical circumstances.

Feb 1, 2024