Search Documents

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack.

Jan 1, 1949

By H. L. TERWILLIGER

THOSE of us who have been following rock drilling work for the last 15 or 20 years can recall some of the problems that were encountered with the old piston type of rock drill and the solid steel which it used. There was frequent trouble in keeping a straight hole in badly broken ground when using the ordinary four- point bit that had a flare on the wings of about 14". The drill steel, when pounding down its hole, would follow the line of least resistance and draw away from the desired line when it encountered a weak side in the ground through which it was drilling. Some would overcome the difficulty by making long winged bits to prevent the steel crowding over; this would relieve the troubles to a great extent. There was trouble with the rifling of drill holes and inability to drill round holes in some ground. The cure for these ills was to use the "X" bit, rather than the crossbit. The "2" bits were brought out in an effort to make it easier to drill a round hole in bad ground. Most of these troubles were before the days when the mechanical drill sharpener was in as common use as it is today. It was not until the introduction of the Leyner type of rock drill, requiring hollow steel that the users of rock drills found themselves confronted with more difficult prob- lems than they had ever encountered before with drill steel because the steel had to stand more severe service.

Jan 1, 1924

By Henry F. Collins

The following notes on the cheap milling of a soft lowgrade ore-body in the State of Chiapas, Mexico, may be of interest. The ore-body in question was worked, not by itself, but incidentally in connection with a large extraction of concentrating-ore; and one 10-stamp battery of a 30-stamp mill used for re-crushing tailings, and provided with copper-plates, was set aside for the treatment of this particular ore, of which, during a period of 17 months, 10,274 tons, of 2240 lbs. each, were handled. Description.—The ore-body collsisted of that portion of a mass of decomposed garnet-rock of igneous origin, which, near its contact with another igneous mass, composed chiefly of the mineral wollastonite in a nearly pure state, had been permeated by solutions, depositing irregularly, throughout it, quartz, chal-

Jan 1, 1902

By D. S. Salonine

Aluminum alloys offer a wide range of capability with a unique combination of advantages that makes them the materials of choice for numerous products and markets. One of the most important applications is their use as the primary structure and outer envelope in aerospace vehicles. Wide and thorough studies on hot working and microstructure evolution of aluminum alloys have been made in Russia. The most important appear to be: - introducing the structure diagrams in strain rate - temperature coordinates which show areas of different microstructures (non-recrystallized, recrystallized, and mixed) after the hot deformation and the following heat-treatment for common aluminum alloys (Yu.M. Vainblat); - studying the press-effect ("structural effect" by V.I. Dobatkin); - learning the influence of hot worked substructure on aging mechanisms; conducting researches on press heat-treatment. These works allowed a deeper understanding and a better control of the mechanical behavior of aluminum products. Comparisons are made to equivalent developments in Europe and America.

Jan 1, 2004

By Nathan Bowersox, Zuzana Skovajsova, David M. Jurich, Brian Harris

When unwatered after more than 50 years of operation, the White Rock Tunnel of the Upper American River Project in the foothills of the Sierra Mountains exhibited failing rockbolts and ground falls. Repairs designed for the 5 mile-long, 24-foot horseshoe unlined hydropower tunnel included pattern rock bolts, shotcrete, and cleanout of the rock trap. The work, originally scheduled for two 3-month winter outages, was completed under challenging conditions in a single 4-month outage following a carefully sequenced work plan using robotic shotcrete and rockbolter machines. Flexibility, creative solutions, and collaboration by all parties were key to project success.

Jun 13, 2021

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFI test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 1, 1986

By Tad Crowie, Victor Delgado, Nick Katsikaros, Tim Hughes

"A number of silver producers have identified a need for a system to recover silver and gold from base metal flotation concentrates on site rather than sending the concentrate to third party smelters to improve mine economics. Historically intensive cyanidation has only been used for coarse gold gravity concentrates in batch machines but Gekko have applied the InLine Leach Reactor (ILR) to these difficult to leach concentrates.The ILR’s unique ability to operate at various solid to solution ratios, high mass capacity, the ability to handle fines, the use of peroxide to aid silver leach kinetics and simple operation has resulted in significant economic benefits to Hochschild PLC’s Selene and Arcata operations. This paper describes the commissioning phase of the ILR5000BA intensive cyanidation reactors on concentrates from the Selene mine at the Ares Concentrator.INTRODUCTIONIntensive leaching of high grade concentrates in gold ore treatment is now commonplace and is considered an essential feature of most gold circuits (Lane, Fountain and LeBrooy, 2008). The devices commonly used for intensive leaching (InLine Leach Reactor, Acacia Reactor, etc) are specifically designed for the typical coarse nature of the concentrate.In some of these intensive leach applications, significant amounts of silver are co-recovered with the gold. In fact, the intensive leaching conditions of 1 to 2% NaCN in solution and high dissolved oxygen levels, overcome the issue with silver’s slow dissolution rate in traditional CIL/CIP circuits and avoids the formation of insoluble silver sulphide minerals on the surface of the gold (Marsden, 2006).There are a significant number of mine operators producing silver in the form of mixed base metal sulphides flotation concentrates. Typically the mine operators are paid for the silver after processing of the concentrate by the base metal smelter whom recovers the silver during the refining process."

Jan 1, 2010

By AIME AIME

T HE Board of Directors of the A. I. M. E. held a meeting at Institute headquarters on Jan. 28, 1921. There were present 10 directors and 14 guests, the secretary and the assistant secretary. The following actions of the Executive and Finance Committees were approved: Wilkes-Barre Meeting, Sept. 12 to 17, 1921; authorization of Oregon Section; authorization of Upper Peninsula Section; appointment of Philip W. Henry and Thomas H. Leggett on special committee on Code of Ethics; and presentation of five copies of Raymond Memorial Volume to T. A. Rickard, who edited it. The By-Laws of the Ohio Section were approved. The resolutions in reference to the payment of certain contributions and assessments to the Library Board of the United Engineering Societies, adopted by the Board of Directors on June 27, 1919, were rescinded, and the resolution adopted that the income of the James Douglas Trust of $100,000 be paid over to the Library or otherwise applied by it for the purpose of maintaining the Scientific Library of this Institute in such manner as may be deemed advisable in furtherance of the purposes of such trust, and that said income shall be paid on account of and included in. the assessment levied by the United Engineering Societies on the Institute for the maintenance of the joint libraries of the Founder Societies.

Jan 1, 1921

By C. W. Owings

Available literature published or abstracted in 1953 and 1954 relating to dust prevention and suppression has been summarized and reviewed in this report, and un-published information also is included to outline current practice for those interested in dust control in and around mines, tunnels, and quarries. More and more companies are realizing the value of controlling dust by incorporating suitable methods and devices in the planning stage. In preparation and crushing plants preliminary tests have been made of the fine materials to determine the best type of dust-control equipment to use, and the details of the quantities of air, the number of sprays, the dust-allaying fluids, and the location of hoods or enclosures have been determined in advance. Such planning has paid for itself in more effective control. Similar planning in a tunnel resulted in healthful conditions and low dust concentrations.

Jan 1, 1956

By Walter E. Lewis

The Fort Randall Reservoir project, on the Missouri River at Pickstown, S. Dak., was designed by the Corps of Engineers and is part of the Missouri River Basin Development Program. The location of the project with respect to adjacent features is shown' in figure 1. When the project is finished, it will include a large earthwork dam and 12 circular tunnels, 8 of which will be equipped for power and 4 for flood control. Various phases of the construction have been contracted to independent companies, and at present four companies are working on different phases of the project under a rigid time schedule. Western Contracting Corp. is the contractor on stage II, earthwork; Johnson-Winston Construction Co. is the contractor for construction of the intake towers at the upstream side of the dam; McCarthy Improvement Co. has the contract for the power house and the outlet works on the downstream side; and Silas Mason Co. has the contract for driving the power and flood-control tunnels. The latter two companies use the same roads for ingress and egress to their respective work areas and the same general waste dump area. Under such circumstances, it is necessary that each company stay on a time schedule in regular sequence to avoid interference with the other.

Jan 1, 1951

By John R. Coulson

Each State and the Federal Government was surveyed for existing certification requirements, the industry yes surveyed for the needs for training blasters, and the training that was available. Recommendations for training and certification for blasters were made.

Jan 1, 1980

By Kenneth R. Maser

This report describes a research and development program sponsored by the United State s Bureau of Mines. The purpose of the program was to develop reusable explosion-proof bulkheads for a cross-cut emergency shelter, and to study the implementation of such bulk-heads, and the resulting shelters, as part of an emergency escape plan in a normal coal mining environment. The first part of this report reveals a number of significant conclusions regarding the application of emergency shelters. A study of the cause s of, and the conditions prevailing during a mine emergency indicate s that ideal placement of the shelter s would be midway along developing entries, and at the inter section of butt and main entries. The proper spacing of shelters is based on the travel capability of trapped miners, which is in turn dependent on the height of coal. The life of a given emergency shelter, based on an analysis of the above information, will be anywhere from 6 months to 10 years. Consequently, some shelters are regarded as "temporary?, while others "permanent?.

Jan 1, 1975

By J. I. Jr. Moore

Many articles have been written about the various operations of Britannia mines and mill, as well as treatises on the geology and ore deposits. A partial list of these papers is given below. Most of these papers have covered well the history of Britannia, and have included a thorough discussion of the geology and ore deposits; therefore, in this paper, no account of these subjects. is necessary. However, a short description of the ore deposits will be given as an aid to a clear understanding of the descriptions of the various mining methods. The Ore Deposits The ore deposits at Britannia occur along a shear zone and are five in number, named for the claims in which they lie, as follows: Jane, Bluff, Fairview, Empress, and Victoria. Each of these deposits is called a mine, as they are separated by 500 to 1,000 feet of barren ground. The Jane mine, although the first producer of the Britannia group, has not been in operation for a number of years. The deposit is a silicified replacement in sediments; with very little evidence of shearing. The Bluff deposit is a highly silicified replacement in porphyry, massive and irregular, very hard in the upper 600 feet with practically no shearing, and softer within chlorite schist in its lower 1,000 feet . The Fairview deposit consists of a series of twelve distinct veins or lodes, rather lenticular in shape, and occasionally merging.

Jan 1, 1928

By B. R. Richards, B. G. W. Robinson

"This paper shows how metal values can be profitably won from a comparatively small and remotely located but high-grade orebody. To do so is not uractical for a large mining company, with its necessarily high overhead of services and organization essential to a large producer.To evaluate, develop and profitably exploit a limited but defined ore deposit becomes only a problem of determining the dollars required to win the dollars available. This paper will record how this was carried out during 1965 and at the same time describe the history, development and production plant of this property."

Jan 1, 1966

By L. C. IlsLey

The theory and practice followed by the Bureau of ones in the investigation of electrical equipment4/ made for service in massy mines are of particular interest not only to manufacturers but also to those organizations that deal with safety and inspection at the mines. This publication proposes to discuss the theory, upon which tests of equipment in explosive atmospheres are based and to consider inspection and other matters pertaining to investigations made bar the Bureau in ascertaining whether a machine merits approval.

Jan 1, 1941

By P. D. Kondos, J. R. Goode

Given the global inventory of low grade and refractory gold deposits, processes that could turn these challenged deposits into mines are of considerable interest. Such gold deposits have low value and potentially high operating costs and so they pose special challenges for the mining engineer and metallurgist. Conventionally, refractory gold ores have been processed by whole ore pressure oxidation and roasting, or flotation followed by roasting, pressure oxidation or bio-oxidation of the concentrate. Halide-based processes have recently been developed that might be applied to concentrates. Low grade refractory gold ores have been processed using heap bio-oxidation followed by cyanide heap leaching or milling. Other processes are emerging. Barrick has completed an inventory of emerging technologies (1). A summary of the current status of these developments will be presented with the view that, with additional development, some of these technologies or a combination thereof may unlock the value of these deposits.

Jan 1, 2005

By Russell G. Shomperlen

Grinding mills in excess of 5 meter diameter and 3500 kilowatts per mesh are putting new demands on big gears. This paper returns to the basics of ring gear design beginning with the fundamental power formulas specified by AGMA. Specific emphasis is given to those elements in the rating equations which require closer attention as gear diameters and transmitted power increase. Strict process control in the manufacture of the gear blank is also stressed. Finally, the writer offers a guide to proper installation, lubrication and maintenance.

Jan 1, 1981

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

By Peter J. Szabo

In 1980, a caravan of representatives of Japanese trading companies debarked on the shores of the United States bearing gifts of watches, electronic games, and radios. In early 1983, we find in a parking lot of a major U.S. coal company, a haggard general manager of marketing returning to the Orient with a box under his arm of trinkets of his own; cross pens with company logos, alarm clocks, etc. The tables have turned, but our fellow sitting in a jet plane over the Pacific Ocean had only to heed the warning of the famous 19th Century poet well familiar with the ways of the Far East. Kipling said; "And the End of the Fight is a tombstone white and with the name of the late deceased, And the epitaph drear, a fool lies here who tried to hustle the East."

Jan 1, 1984

By Janne Kytökari

Controlling a wide range of minerals processes with single control system is an ordinary way to operate in mines all over the world these days. However the potential of these systems is not yet fully recognized nor utilized. The key issue is to manage the information in a way that enables automating the day-to-day tasks, quality control and safety functions. At the same time it provides means for optimization and constant improvement of processes creating a working environment where the system helps employees to do their key tasks instead of searching, modifying, and transmitting the huge number of information arising every day. The distribution of control system nodes enables the other processes to run heedless of a problem occurring in one of the sub-processes. Also the control room can be in remote location such as in large city removing the need to travel substantially long distances to plant sites every day. When all essential information is brought to the same place there is less risk for a mishap to happen due to information breaks that are often the cause of them. One of the biggest single reasons that result in production losses are break downs of machinery usually caused by normal wear, misuse, incorrect utilization rate etc. For this reason it is important to measure the condition of machines using vibration measurement and diagnostics. By moving from failure or time-based maintenance towards predictive or performance maintenance generates eventually a steady and predictable process but also results in significant long term savings. The mineral process at Talvivaara mine is based on bioheapleaching, whereby metals are leached from ore as a result of bacterial action. Bioleaching is a fairly new technology used in metals recovery. Therefore it is important for the mine to collect and analyze data from different stages of the minerals process. Talvivaara mine?s Metso DNA system has integrated machine condition monitoring and information management. These are not only necessary but also crucial in environmental conditions where the outside temperature can drop below -35°C, where ice and snow dominate the landscape and impact the equipment for four months a year and where distances between equipment can be up to 7.5 kilometers. Keywords: DCS, analyzer, machine condition monitoring, automation, remote communications, optimization, mining, metso DNA, Talvivaara

Sep 1, 2012