Search Documents

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By J. McCreedy

This paper reviews new methods of exploration for metals and new techniques of mining the deposits and extracting the metals from their ores. Examples of mining innovations are taken from Inco's Thompson Operation. The importance of presenting a favorable image of the industry to college students and young people deciding on a career is stressed.

Jan 1, 1971

By Zhang Jianliang, Zuo Haibin, Gao Bing, Wang Zhe

"As a result of the shortage of coking coal and the quality decrease of coke, it is important to know how to make better use of highly reactive cokes. The co-gasification behavior of highly and lowly reactive coke for blast furnace is investigated. The results show that: In the middle stage of reaction, the weight loss ratio of highly reactive coke reacted together with lowly reactive coke is higher than that of it reacted individually. However, the weight loss ratio of lowly reactive coke is lower. The weight loss ratio of highly and lowly reactive coke is almost the same as that of the weighted average. The scanning electron microscope analysis indicated that the reaction degree of surface and interior of lowly reactive coke is relatively uniform with the reaction time increased. And the reaction degree of surface of highly reactive coke is obviously higher than that of interior.IntroductionIn blast furnace iron making process, coke functions as heat supplier, reducing agent, carburizer and skeleton. With development of blast furnace iron making technology, the skeleton function of coke is becoming more and more important in requirements of large scale furnace and high pulverized coal injection. High reactivity coke is usually produced by cheap coal with bad quality, and is not good for blast furnace process. The reactivity of coke is mainly determined by the coals used, and the resource of good quality coking coal is limited and is non-renewable. In order to fulfill the need of blast furnace, a lot of research have been done to improve coal matching using new kinds of coal to enlarge resource, in which coking coal and fat coal are reduced, whereas low price coal with bad caking property are used to lower the cost, and this would inevitably increase the reactivity of coke [1-4] Blast furnace iron making would still be the main stream for a predicted future, and high reactivity coke would correspondingly be used more and more, so it has great importance to study how to use high reactivity coke in blast furnace."

Jan 1, 2013

By Donald L. Colwell

THIS is a metallurgical war. More than ever before, the mechanized forces and the air-borne warfare are deciding campaigns. Both of these are primarily dependent upon metals. There are two ways of increasing the effective supply of these metals when the demand is greater than the total over-all supply. The American custom, when a shortage of anything develops, is to get more. In the case of some nonferrous metals this has been done. For example, our potential peak output of magnesium will be almost one hundred times the prewar production. Output of aluminun has also been tremendously increased, and production of other metals is being stimulated by every possible means. Our enemies, however, have another successful method of increasing the effective supply of a material, and that is, to eliminate entirely all nonessential uses, and also to use, in essential applications, alternate materials wherever possible. Sometimes, ersatz material is inferior to the original, and consequently does not do the job as well. Often, however, it has been found superior, and many substitute items are now being used both by industry and by the military which will continue even when the original material again becomes available.

Jan 1, 1943

By Alan M. Russell

In recent years, several rare earth intermetallic compounds with the B2-type structure have been reported to exhibit high tensile ductility and high KIC fracture toughness at room temperature. These materials retain considerable ductility even at 77K. These are noteworthy findings because most intermetallics possess poor room temperature ductility and low fracture toughness unless one or more special contrivances are applied (e.g., doping with small additions of interstitial elements, offstoichiometric compositions, testing in ultra-dry atmospheres, etc.). This paper summarizes recent findings on rare earth B2 intermetallics. These include the determination of the active slip systems; the strain rate sensitivities; yield strength maxima at elevated temperatures; the search for possible twinning and stress-induced phase transformations; ab initio calculations of their defect energies and the anisotropy of dislocation line tension. Potential applications of these materials and the possibilities that this study may suggest strategies for increasing ductility in other intermetallic compounds are discussed.

Jan 1, 2008

By Barbara H. Scott Smith

"During the last two decades lamproites have joined kimberlites as the only two known primary sources of economic quantities of diamonds. This paper contrasts the petrography, primary and xenocrystic mineralogy and pipe geology of these petrogenetically separate rock types. The petrographic discrimination of kimberlites and lamproites from each other, as well as other rock types found during diamond prospecting, is discussed. Kimberlites and lamproites can be classified texturally and mineralogically. Such classifications highlight the differences between, and among, lamproites and kimberlites. The implications of these differences for diamond exploration programs are discussed, with particular emphasis on the application of petrography. IntroductionKimberlite was the term coined in the late 19th century to describe the host rock of diamond at the type locality, Kimberley, South Africa (Lewis, 1887, 1888). Innumerable kimberlites are now known worldwide; some of them contain economic quantities of diamond (e.g. South Africa, Botswana and Russia) while many are barren. Jennings (1989) suggests that less than 3% of the known kimberlites can be considered to be commercial. Kimberlite was thought to be the only important primary source of diamond for approximately a century. Until the late 1970s, lamproites were thought to be only academic curiosities. Some workers (e.g. Wade and Prider, 1940), however, did comment on certain similarities between lamproites and kimberlites and, hence, inferred a potential for lamproites to carry diamonds.The term lamproite was introduced by Niggli (1923) for leucite-bearing rocks from southeast Spain and Wyoming which had some unusual geochemical characteristics. Wade and Prider (1940) used the term lamproite (as defined by Troger, 1935) to embrace rock types found in the West Kimberley area of Western Australia. All the lamproites described by Wade and Prider (1940) form distinct topographic features. Subsequently in the late 1970s, additional pipes, which have little or no relief, were discovered in the same area, but only as the result of a major diamond exploration program (Atkinson et al., 1984; Jaques et al., 1984, 1986). Some of these bodies are diamondiferous. In 1979, the Argyle pipe was discovered in the East Kimberley area which, in terms of grade, is the richest known primary diamond deposit in the world with some parts of the body having grades greater than 500 carats/100 tonnes (Madigan, 1983; Boxer et al., 1989). All the initial new discoveries in Western Australia resulted from classic stream sampling for ""kimberlite indicator minerals"" (Atkinson, 1989)."

Jan 1, 1992

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By Mark Colwell

As per most other earth science engineering problems, the underground coal geotechnical environment and the way in which roof and rib support interacts with the rock mass are complex issues. While the problem should not be oversimplified (i.e., the dominant failure mechanisms or critical data input parameters should not be ignored), without question judicious simplification is at the heart of all good engineering design. Engineers play a vital role in supplying the world with solutions and products; however it is crucial that engineers make practical and readily useable contributions. One way to ensure this is to employ simplification in the engineering process.

By C. L. Glorioso

As an introduction and credentials for our talk, let me take a moment to introduce you to Wimpey Worldwide and specifically to Wimpey Minerals, USA, Inc.

Jan 1, 1995

By S. C. Sun, A. M. Gaudin

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By A. M. Gaudin, S. C. Sun

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By D Bertoldi, C Haines

"The Waihi Gold Mine (WGM) operated by OceanaGold New Zealand Limited is a wholly owned subsidiary of the OceanaGold Corporation of Australia. Traditionally WGM has stockpiled and processed separate campaigns of open pit and underground ore. The ore is processed via a conventional semi-autonomous grinding (SAG) / ball circuit (SABC). The low aspect SAG mill operates in a closed circuit with two 20" cyclones, whilst the ball mill is also a closed circuit with a 10" cyclone cluster. A major wall movement in April 2015 ceased open pit operations indefinitely, 18 months ahead of the mining plan. This immediately reduced the forecast mill tonnage leaving two options: begin campaign milling or change the operating strategy and target lower throughput. Additional cost pressures necessitated improved milling cost efficiency. The immediate ore restriction limited processing alternatives to within the existing major infrastructure. Available comminution circuit survey data laid the foundation for developing a comminution model using the JKSimMet™ software package (version 6, created by KJTech). A number of flow sheet variants were then evaluated based on predicted throughput and efficiency. The comminution models suggested opportunities for improved efficiency lay in reducing throughput and increasing utilisation rather than on/off campaign milling under the existing operating philosophy. A series of process alterations followed, delivering new cost efficiencies that maintained the current $/t processing cost. This paper aims to review the change in circuit performance and examine the decisions and challenges faced following the transition from a high tonnage SABC circuit to lower tonnage SABC circuit.Citation:Haines, C and Bertoldi, D, 2016. The Transition from Semi-autogenous to Autogenous Milling at Waihi Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S. J. van Wyk, A. S. H. Haagner

Land rehabilitation transcends the mere establishment of vegetation across disturbed landscapes; it should be conceptualised as a specialised ecological reconstruction process. This process necessitates a long-term perspective on the success of land repurposing. It requires a continuum of inputs specified and managed by a dedicated and qualified custodian to ensure the sustained economic viability and ecological sustainability of the land. Based on the authors’ combined experience and field observations over more than five decades, they advocate for an urgent shift away from traditional land rehabilitation practices toward a paradigm centred on land capability reconstruction and active stewardship. The prevailing rehabilitation culture has overly simplified the process to a mere revegetation exercise, which is fundamentally incompatible with the comprehensive requirements for sustainable land capability. While the regulatory framework provides valuable guidance for obtaining a mine’s social license to operate, a paradigm reset is essential. Mining companies must prioritise rehabilitation quality, set achievable sustainability goals, and establish clear pathways and milestones to meet relinquishment criteria. Currently, the status quo view—a model reliant on outsourced contracting and agricultural approaches—is that mine rehabilitation is a one-time intervention rather than a complex, systemic, and long-term process. This perspective presents significant challenges, as the success of ecological interventions can only be accurately assessed over extended timeframes, often spanning decades. Shortsighted rehabilitation specifications, coupled with practitioners operating within agricultural decision frameworks, frequently overlook the necessity for integrated rehabilitation expertise and the scientific foundation essential for designing and implementing effective ecological outcomes. A lack of long-term monitoring information impedes the required adaptive management of rehabilitated systems and, therefore, delays the transition towards final land use. This short approach costs the mining industry millions annually, often without recognising the inadequacies in long-term liability mitigation and the substandard ecological success achieved. The disconnect between procurement processes, the qualifications of service providers, and the unclear pathways to relinquishment can impede successful rehabilitation outcomes, frequently undermining progress toward sustainability milestones. Unless there is a fundamental reset of the land rehabilitation culture, pursuing sustainability will remain an elusive and perhaps impossible objective. Consequently, mining companies may hesitate to fully commit to sustainable land rehabilitation practices, as the prospects for relinquishment and final closure remain uncertain at best.

Apr 25, 2025

By C. Igathinathane

Coal is the most widely used fossil fuel in the world, providing more than 25% of world?s electrical power. Since, the behavior of coal particles in crushing and grinding circuits, concentration operations, and solid-liquid separations is strongly dependent on size, a reliable and accurate measurement of particle size and particle size distribution (PSD) is a vital aspect in coal cleaning. This paper presents a method for the characterization of ground coal particles using image analysis. We utilized a machine vision (MV) approach that used a document scanner as the imaging device and a user-coded ImageJ plug-in that processed the image and automated the PSD analysis and output results in textual and graphical forms. This approach used a sum of volumes (SVolume) as weighting factor for particle length as the primary dimension of analysis and was successfully applied to ground coal. The plug-in was further improved for computational performance in this study. Mechanical sieving (MS) was also used to compare the MV results. MV results showed that the PSD of ground coal followed a uni-modal normal distribution, and the log-normal plot against particle size exhibited a linear trend for most of the range. MS results, however, had three linear segments, when the width-based sieving results were transformed to lengths by applying the shape factor (width/length), but a definite deviation between the PSD plots was observed. This study demonstrates successful application of the MV SVolume approach for PSD analysis of ground coal, which can be extended to similar particulate minerals and products. Keywords: dimension, fiji, image j, image analysis, coal, particle size, plug-in

Sep 1, 2012

By Hwasoo Park

Keywords: FC mold, Argon, Magnetic, Solidification Fluid flow plays a significant role for steel surface quality in continuous casting. Although water models are able to model fluid flow, the flow pattern is not of practical interest since the moving solidifying shell cannot be accounted. Computer modeling has become a popular and dependable tool to analyze the complex phenomena occurring in continuous casting. In this numerical simulation we coupled momentum and energy equations considering the solidification of steel along with turbulence ?-e model. The vertical bending mold is equipped with bifurcated nozzle with 15 degrees of port angle. FC mold is supplied with DC induced magnetic fields. Influence of argon and magnetic fields on molten steel flow and heat transfer is investigated by solving momentum equations adding source terms due to multiphase ? magneto hydrodynamics. The results show that magnetic fields reduce the jet velocity from port by lower magnetic core induced field but the influence on meniscus velocity is complex to describe. Magnetic fields increase surface temperature and homogenize its distribution on surface and inside a mold.

Jan 1, 2005

By William Gleason

"Komatsu has been on the cutting edge of autonomous mining for the past 30 years and the company remains at the forefront of the technology that is changing from concept to a full-fledged reality.In 1996, Komatsu America Corp. (KAC) purchased a controlling interest in Modular Mining Systems; a move that enabled both companies to expand their product lines. It was through this effort that Modular helped to deploy the first autonomous haulage system (AHS) — the Komatsu FrontRunner system. In January 2008, the first commercial implementation of the FrontRunner system occurred at Codelco’s copper mine in Chile. Since then, Komatsu has put more than 130 haul trucks into seven sites on three continents to haul copper, iron ore and oil sands and its equipment has moved 1.8 Gt (2 billion st) of material with zero lost time incidents attributed to Komatsu’s autonomous trucks. The 1.8 Gt (2 billion st) is the most of any commercial mining autonomous haulage system and there is more to come. In November, Komatsu announced that an additional 150 autonomous haul trucks will be deployed to the Canadian oil sands over the next seven years.Komatsu has continued to pioneer autonomous haulage development, creating a range of autonomous options that includes semiautonomous and teleremote options all the way up to a haulage vehicle that stole the show at the world’s largest mining equipment trade show.In 2016, Komatsu advanced the concept of driverless haul truck to a new level when it displayed its Innovative Autonomous Haulage Vehicle (IAHV) at MINExpo in Las Vegas, NV. The concept vehicle is the first mega class haul truck designed to be fully autonomous, without an operators’ cab included on the vehicle.Unlike other haul trucks, the vehicle was developed exclusively as an unmanned vehicle designed to maximize the advantages of unmanned operation. Among other advancements, it was designed to distribute equal load to the four wheels, both when the vehicle is loaded and unloaded, and adopt four-wheel drive, retarder and steering. Komatsu said it is aiming for high-performance shuttling of this vehicle in both forward and reverse travel directions, thereby eliminating the need for K-turns at loading and unloading sites."

Dec 1, 2018

The 32nd annual American Hall of Fame Awards Banquet and Fundraiser, sponsored by the Mining Foundation of the Southwest (MFSW), will be held at the JW Marriott Tucson Starr Pass Resort & Spa on Saturday, Dec. 6, 2014. Each year, one living Hall of Fame inductee, up to three Medal of Merit recipients, honorees from mining?s past, and recipients of an Industry Partnership Award and a Special Citation are recognized for their respective contributions to the mining industry. Armine Frederick Ban?eld Jr., past chairman and founder of Mintec, Inc. located in Tucson, AZ, will be honored as the 2014 Hall of Fame Inductee at the awards banquet. Banfield founded Mintec from his Tucson apartment in 1970 and expanded it to a global operation. Under his guidance, Mintec won the 2013 President?s E-Award for Exports ? the highest recognition any United States company may receive for making a significant contribution to the expansion of U.S. exports. Medals of Merit will be awarded to Corale L. and James A. Brierley, founder and principal of Brierley Consultancy LLC; David Nicholas of Call and Nicholas Inc. and Scott M. Shields of Joy Global. The Brierleys are being recognized for their true scientific partnership with parallel achievements in academia and in business development. Nicholas is being recognized as the co-founder of Call & Nicholas and for his noted expertise in mining geotechnical engineering. Shields is being recognized for his innovative work with GPS integration and for playing a key role in laying the foundation for autonomous mines of the future. As representatives of mining heritage, the Hall of Fame will induct Patrick E. Connor, ?Father of Utah Mining,? for pioneering mineral exploration efforts in Utah; Earl Tappan Stannard, president of Kennecott Copper Co., for transforming Kennecott in to one of the largest U.S. copper producers; Arthur Barrette Parsons, mining editor and author, for his book ?The Porphyry Coppers in 1933,? a seminal work detailing the history and technical information regarding major porphyry copper deposits and Ernest R. Dickie, general manager of Bagdad Copper Co., for his foresight in converting the mine from block caving to open pit. The Industry Partnership Award will be presented to Empire Southwest, a third generation family owned dealership for Caterpillar which consistently ranks among the top Caterpillar dealers worldwide. A Special Citation will be presented to employees of Rio-Tinto-Kennecott Bingham Canyon Mine for their speedy recovery from the massive Manefay slope failure in 2013.Early sponsors include Ames Construction, Asarco LLC; Brierley Consultancy LLC; Caterpillar Inc.; Click Automotive Team; Deconcini McDonald Yetwin & Lacy, P.C.; Empire Southwest; Florence Copper Inc.; Freeport-McMoRan Copper & Gold Inc; Independent Mining Consultants Inc.; Joy Global Inc.; Komatsu America Corp.; Liebherr Mining Equipment; Lowell Copper Ltd.; M3 Engineering & Technology; Modular Mining Systems Inc.; MWH Global; Newmont Mining Corp.; Ram Enterprise; Rio Tinto/Kennecott, Sonoran Process Equipment Co.; Southwest Energy LLC and SRK Consulting. MFSW is a nonprofit organization and its mission to promote the value of the industry to our community and profession to ensure its future success. Funds raised from its annual banquet are principally designated to support the foundation?s education program, a partnership with the Lowell Institute for Mineral Research at the University of Arizona.

By Patricio Oyanader

La innovación es una disciplina que busca resolver retos a través de soluciones nuevas que generen un beneficio para la organización. En ese sentido, el presente texto señala los cuatro elementos clave (estrategia de innovación, desempeño, personas para innovar y los dispositivos habilitadores) en la gestión de la innovación de una empresa. Dentro de ese grupo de elementos, el tercero es el más importante -en tanto son las personas las que generan innovaciones en la resolución de sus problemas. Así, la novedad y el beneficio son conceptos que rompen los paradigmas de lo tradicional y viabilizan los desafíos operacionales como los de la gestión

Sep 1, 2013