Search Documents

By B. Simser

At Brunswick Mine, an increase in the number of seismically-related falls of ground and in particular rockbursts occurred during 1999. This was due to the ever-increasing stress levels in the remaining ore reserves, mining in difficult highly stressed areas and in particular troublesome geological features. In conjunction with the Noranda Technology Centre, development of rockburst support systems started at the Brunswick Mine in 1996 and efforts were accelerated in 1999. A support package consisting of #6 gauge chain link mesh, #0 gauge heavy mesh straps, and a 1 m by 1 m pattern of modified conebolts was developed. The conebolts were modified to enable mixing of the resin anchoring. Two major rockbursts occurred during an intense seismic episode at the Brunswick Mine from October 13th to 17th , 2000.The area was evacuated approximately four hours before the first burst hit, and remained closed during the seismic ?flurry??. The first damaging activity occurred around midnight on Friday the 13th, and a second damaging episode occurred on the 17th that included a local Richter Magnitude 2.7 event. The second rockburst had dimensions of approximately 5 m by 5 m by 20 m or 2150 tonnes of massive sulphide material (density 4300 kg/m3). The first failure area was more extensive, caving approximately six metres of an intersection back with the lateral extent not safely measurable. This paper briefly describes the mining conditions that led to the bursting, the seismic response of the region, the mechanisms thought to have caused the bursts, and a yielding support system which had been partially installed before the burst.

Jan 1, 2002

By N. E. Norman

The big hole drilling industry is a relatively new one. In fact, very little big hole drilling was done prior to 1950. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry. Let us examine the three main features of big hole drilling and determine how each applies to mining. Let's also look at the good qualities and the limitations of each of these character traits.

Jan 1, 1968

By Zhou Shu-cai

"A method has been proposed for the pre-treatment of high phosphorus iron ore by carbothermic reduction assisted with microwave irradiation and magnetic separation on a laboratory scale. Chemical analysis of the reduced ore sample, the metal sample and the slag sample were conducted. Based on the above research, the influences of carbon addition, microwave power and microwave irradiation time on the recovery of Fe and dephosphorization were discussed. It indicated that the increase of microwave irradiation time and power had substantial effect on the recovery of Fe while the influence of carbon addition was not obvious and the highest iron recovery ratio reaches some 95.5% when the dephosphorization ratio was 37.68%. A high iron recovery ratio and a reasonable dephosphorization rate were incompatible under the conditions investigated in this study due to the reduced iron and because unreduced P-contained gangues were not efficiently separated. This method may provide a reference for the future utilisation of high-phosphorus iron ore.IntroductionWith the rapid growth of crude steel production in China, the source of iron ore tends to become increasingly strained and is facing the risks of raw material shortage for the iron and steel industry. In order to decrease the production cost, China has to focus on the utilization of its domestic low grade iron ores for the iron and steel plants [1-2]. China has a large deposit of high phosphorous iron ore with a reserve of 7.45 billion tons which is unused in any large scale [3]. Therefore, the development of a successful and economically viable technology for high phosphorus iron ore is of profound importance. To remove phosphorus from the high phosphorus iron ore, several mineral and metallurgical processes have been proposed, such as bio-leaching [4], roasting reduction plus melting separation [5], pre-reduction and screening methods combined with mechanical crushing or air jet milling[6] selective agglomeration plus reverse flotation [7]. However these processes are not cost effective or are time consuming. The traditional pyrometallurgical process( BF+ BOF) refuse this kind of ore mainly because that molten iron is saturated with carbon or high carbon content and thus all phosphor us in the burden goes to the molten iron[8]. Therefore, it is important to exploit the cheap and abundant high phosphorus iron ore as a resource in ironmaking. In recent years, the microwave was widely introduced as a heat resource for extractive metallurgy of iron ore or other minerals. For example, microwave assisted ore milling, microwave assisted carbothermic reduction of metal oxides and microwave assisted mineral leaching issues[9-10]"

Jan 1, 2014

By Sergio Cattalanl, Francis Chartrand

"The geology and origins of volcanogenic massive sulfide (VMS) deposits in the Abitibi belt of northwestern Quebec have been the subject of discussion since the discovery of the Horne orebodies in Noranda in 1923.The present Noranda version of the VMS model characterizes the ideal deposit as a stratabound, base-metal accumulation that is in close spatial relationship with hydrothermal alteration and stockwork zones, felsic lava domes, coarse phreatic-pyroclastic breccias, and subvolcanic intrusions that characterize vent- and proximal{acies submarine volcanic environments. Deposits tend to occur in a favorable stratigraphic interval within a mining camp, and this is well-documented in the Rouyn-Noranda and Matagami camps.However, in recent years many VMS deposits have been shown to deviate from the ideal Noranda-type. For example, the Ansi/ deposit is characterized by sulphide-bearing alteration zones that extend far above the massive sulfide lenses, and by abundant magnetite immediately underlying massive sulfide. The Horne deposit appears to lack the typical chloritic alteration pipe underlying the massive sulfide lenses, as well as laterally-equivalent exhalite horizons. The Horne and Quemont deposits, besides being the two giants of the camp, are particularly rich in gold, whereas others, such as WaiteAmulet and Millenbach, have low gold values. Finally, some deposits in the Noranda camp, such as the Ansil, Corbet and Mobrun mines, are outside the favorable stratigraphic interval. Therefore, it would appear that part of the key to renewing base metal reserves in northwestern Quebec is the use of evolving descriptive-genetic models that incorporate geological variations like those cited above."

Jan 1, 1990

By Judy K. Todd

Double benching has been utilized as an excavation technique in open pit mines for many years. This process involves drilling, blasting, and excavating the material for the design bench height. A second bench is then excavated without the creation of a catch bench, i.e. only minimal offset from the first bench face is allowed when drilling off the second bench. The result is a double high bench face or double bench. When drilling off the second bench, the offset of the drill from the bench face projects the lower bench face into the pit up to an extra five meters. This reduces the maximum attainable bench angle, enhances the probability of rock escaping the catch bench and increases the overall strip ratio. The generally utilized process of trim blasting also can impact on the final bench profile by contributing to blast damage of the face. BHP Billiton Diamonds Inc., Ekati Mine Diamond MineTM, has pioneered the usage of a technique that eliminates this offset. Double benching is accomplished by drilling a single, 30m pre-shear (two 15m benches) to define and protect the final bench profile. This article provides a comparison of the attained face angles obtained in the field utilizing both of the above methods, as well as a comparison with the analytically predicted angles prior to excavation.

May 1, 2002

By Sheldon P. Wirnpfen

AN extensive study of German underground manufacturing experience is being undertaken by the Air Materiel Command. Headquarters officials consider completely underground facilities one of the most effective means of protecting aircraft production against air attacks of the strength and type employed in World War II. Advantages accruing to underground manufacturing installations other than protection are, perhaps, a smaller maintenance problem and the possibility of using gravity flow on some production lines. Offsetting these advantages are the high cost of construction, problems of ventilation, and poor acoustics. Excavation costs might well be less than the cost of enclosing the same area on the surface, as new and better methods of rock drilling and transportation are developed. Certainly the amount of building materials used would be far less than in constructing a surface plant of the same dimensions. A fewer number of skilled workers would be required to perform the labor of excavation. Underground construction would

Jan 1, 1947

By L. Stein

A simplified radiochemical method has been developed for quantitatively analyzing; radon gas in underground uranium mines. In this method, a measured volume of air is drawn by a pump through a drying tube and a cartridge containing dioxygenyl hexafluoroantimonate reagent. Radon is captured as n nonvolatile product. After radioactive equilibrium has been established between radon and its short-lived daughters (approximately 4 hours), the gamma-emission of the cartridge is measured with a scintillation counter. The amount of radon is then calculated from the gamma-emission rate. The effect of cartridge geometry, reagent load, and air flow rate upon collection efficiency and counting efficiency is reported.

Jan 1, 1977

By J. Larsson

In the pursuit of increased safety the mining industry has worked to develop systems for remote control and autonomous operation of both stationary and mobile equipment. This paper reports on a newly developed system for teleoperation and autonomous tramming of LHD (Load-Haul-Dump) mining vehicles that not only increases the safety of the operators, but also has the potential to increase productivity.

Jan 1, 2010

By F. A. Rutledge

[An a part of the United States Department of the interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits of nonmetallic minerals accessible to the Alaska Railroad for use in building; materials is In the Alaska Railroad-belt area. The results of the investigations, to date, indices that raw materials for the preduction of brick products are in plentiful supply as cloy in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.]

Jan 1, 1953

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994

By D. M. Schubert

As a clean and renewable energy carrier, hydrogen is an important component of most alternative energy portfolios. Hydrogen combines very high energy content by weight with excellent environmental attributes. Since hydrogen reacts with oxygen to produce only water with release of energy, it can be used to power fuel cells, combustion engines, and turbines, without production of greenhouse gases at point of use. However, because of its low volumetric density, storing pure hydrogen is impractical. Thus implementation of hydrogen technologies requires materials that can safely store and release large amounts of hydrogen (1,2). In recent years, the U.S. Department of Energy (DOE) and other governmental agencies around the world sponsored extensive research on hydrogen storage materials, including those based on boron. These efforts have resulted in significant advances in hydrogen storage technologies. Boron materials stand out as leading candidates for hydrogen storage among the many options investigated. Combining excellent hydrogen densities, release rates, and safety characteristics, some boron materials can hold substantially more hydrogen by weight and volume than even pure liquid hydrogen (3-5).

Jan 1, 2010

By Aleksandar D. Bugarski

Three types of uncatalyzed diesel particulate filter (DPF) systems, three types of high-temperature disposable filter elements (DFEs), and one diesel oxidation catalytic converter (DOC) were evaluated in underground mine conditions for their effects on the concentrations and size distributions of diesel aerosols. Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. The DPF systems reduced total mass of aerosols in the mine air approximately 10-fold for light-load and 20-fold or more for high-load test conditions. The DFEs offered similar reductions in aerosol mass concentrations. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the filter element. The effectiveness of DPFs and DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. The effects of the DOC on mass and number concentrations of aerosols in mine air were relatively minor when compared to those of the DPF and DFE systems.

Jan 1, 2009

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By Jürgen Kretschmann

The Islamic Republic of Iran is a very important producer of raw materials in the world. The country holds 68 types of minerals, including salt, sand and gravel, chrome, lead, zinc, copper, coal, gold, and iron-ore. With more than 37 billion tons of measured and indicated reserves and 55 billion tons of total mineral resources, Iran is ranked among the 15 major mineral-rich countries. Sangan iron-ore mines (SIOM) is one of the biggest iron ore mining complexes in Iran, located in a remote, but strategically important area near the Afghanistan border. The Iranian government has planned several mining projects in this region for a stepwise development over the next 5 years to satisfy the growing demand of the Iranian steel industry. In cooperation with private companies, these projects shall be realized as sustainable as possible. This paper introduces SIOM and describes socially responsible activities undertaken during the initial development of this mining complex. The effects of these activities will be demonstrated. Unique attributes of the Sangan area have a significant impact on the acceptance of SIOM by regional stakeholders. The government has made several social investments that benefit workers´ families and the community. They are attempts to build social capital for the mining operations and demonstrate a commitment for socially responsible mining to the communities and the local population. They aim to create a balance between the local and regional expectations and requirements and the necessity to secure the corporate profitability at a reasonable and sustainable level. Investment in socially responsible activities is not a choice but a necessity to improve the relations between mining companies and stakeholders in the communities. It is recommended that social investments should be carefully planned and implemented from the early stages of mining activities, and should proceed throughout the life cycle of the mines.

Aug 1, 2013

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 (PL 109-236, 2006) established the Office of Mine Safety and Health, functioning as the Office of Mine Safety and Health Research (OMSHR) within the National Institute for Occupational Safety and Health (NIOSH) and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued more than 150 contracts focused on worker health and safety. Initial funding for this program was provided by the United States Congress through two emergency supplemental appropriations and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation. Ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website (www.cdc.gov/niosh/ mining/researchprogram/contracts/index.html) and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously (Snyder et al., 2016).External contracts are broadly classified by the following areas:• Communications and tracking.• Emergency response.o Self-escape and breathing air supply.o Refuge alternatives.o Escape and rescue.• Equipment safety.• Fires and explosions.• Ground control.• Mine environmental systems (mine ventilation and atmospheric monitoring).• Worker/workplace health and safety.Contracts are issued under a request for proposal (RFP), through a broad agency announcement (BAA) or under an interagency agreement (IAA). An RFP solicitation includes a specific problem description and a well-defined scope of work to guide the offeror in preparing a bid to conduct the research. Under the BAA several problem areas are described and the offeror develops the scope of work and deliverables for the proposed research. An IAA is very similar to an RFP except it is a contract between two federal government agencies."

Jan 10, 2018

By Frank Agyemang, Zainab Nasrullah, Richard LaDouceur, Mehran Saddat

To sustain the circular economy, defence applications, and other renewable technologies, recycling rare earth elements (REEs) and other critical elements from their secondary resources is important. This cause has resulted in rigorous research and development for viable extraction and separation of REEs. Previously, Sm-Co recycling has been done with technologies, which fall under the categories of pyrometallurgy, physical separation, and hydrometallurgy. All these methods have limitations associated with energy, cost, and environment. Reportedly, the chemical leaching technology has successfully recovered and separated Sm-Co. Still, it has limitations associated with slow mass transfer and leaching kinetics, and there is a need to intensify the process to make it time efficient. This approach has also adversely impacted the environment by an extensive use of toxic, corrosive, non-selective, and expensive reagents. In this research study, chemical leaching of Sm-Co was performed using this new class of solvents, Deep Eutectic Solvents (DESs), which fall under the category of ion metallurgy. Four different DESs were used, proven to be green, non-toxic, biodegradable, cheap, and selective for cobalt over samarium by 82% leaching conversion. To improve the slow mass transfer and leaching time, this new technology of resonant vibratory mixing (RVM) was also tested. RVM intensifies mixing by establishing near instantaneous, low energy mixing conditions through resonance. It has been shown to improve the adsorption kinetics and was tested for the leaching kinetics. Four combinations of DESs were prepared, which are made up of two quaternary salts: Choline Chloride and Tetra Butyl Ammonium Chloride, and three organic compounds: Oxalic Acid, Urea, and Ethylene Glycol. These combinations were used for chemical leaching of Sm-Co with leaching factors of time, temperature, and type of DESs. After leaching, the samples were tested with and without resonant vibratory mixing with conditions of time, intensity (%), and type of DESs. Samples were analysed with Induced Coupled Plasma - Optical Spectroscopy (ICP - OES). Future work will involve a life-cycle assessment to assess the RVM technology with other conventional mixers, and an extensive study of DES properties to improve selective leaching.

Feb 1, 2025

By D. C. Oliver

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy and Materials) degree Corrosion in exhaust systems can occur on both the interior and exterior surfaces. Chloride-containing de-icing salts on the roads in colder countries greatly increases the rate of corrosion on the exterior surfaces. This paper investigates the relative exterior corrosion resistance of three alloys?two ferritic stainless steels( AISI Types 409 and 441) and an aluminized mild steel. The exhaust system is split into two categories?the hot end and the cold end. A test for each of these ends was designed?the standard ASTM G85test was modified to create a simulated driving cycle. The cold end test samples were exposed to ten driving cycles, and the hot end test samples were exposed to five driving cycles. A driving cycle constitutes the car being started from cold, driven until the operating temperatures are reached, and switched off and allowed to cool. Pitting corrosion is the primary corrosion mechanism occurring at the cold end of the exhaust system. The aluminized mild steel was the most resistant alloy in this test, and Type 409 the least. However, once the protective aluminium layer degrades, corrosion will occur rapidly. At the hot end of the exhaust system, spalling of the surface oxide layer is the primary corrosion mechanism occurring. Type 441 was the most resistant in this test, and the aluminized mild steel the least resistant. Potentiodynamic tests were performed on the alloys?the results agreed with the results obtained in the exposure tests.

Jan 1, 2003

By Alistair James, Mo Shahsavari, Leon Botham

Recent catastrophic failures of heap leach facilities have revealed fundamental weaknesses in prevailing design paradigms, modeling toolkits, and oversight practices that continue to treat heaps as static, free-draining earthworks despite compelling evidence to the contrary. The core proposition advanced in this paper is that heap materials are intrinsically dynamic: their structure, permeability, and shear strength evolve under the sustained influence of irrigation, climate, and geochemical reactions, and these timedependent changes can precipitate abrupt transitions from granular stability to flow-like failure. Drawing on investigations of recent failures at Çöpler Mine in Turkey and Eagle Gold Mine in the Yukon, alongside earlier incidents in Peru, Arizona, Nevada, and Chile, the analysis identifies a recurrent sequence driving catastrophic behavior: progressive weathering elevates fines and suppresses permeability; drainage systems designed for initial conditions become overwhelmed; pore pressures rise heterogeneously within the heap; and static liquefaction initiates rapid mass movement with long runout. Current guidance, including ICOLD and ANCOLD frameworks and ASTM testing standards, provides a necessary foundation but is tailored to tailings and conventional soil mechanics. These documents offer insufficient direction for characterizing timedependent material degradation, quantifying rheology of weathered ore, and modeling post-failure mobility. To address this deficit, the paper proposes an integrated framework combining enhanced characterization, multi-physics numerical modeling that couples hydro-geochemical processes with large-deformation mechanics, and comprehensive monitoring with Trigger Action Response Plans. The conclusion argues for a heap-specific standard that embeds these elements from concept to closure, aiming to materially improve safety performance and reduce the likelihood and consequences of future failures.

Feb 22, 2026

By Jr. Goller

You and I can visit cement plants, inspect the various rotary kiln systems and find some equipment or some burning techniques that waste energy--fuel and power. After we have made such a visit and studied a few ideas, we could recommend ways to eliminate much of this waste. Probably every idea would cost money to bring into action. For our discussion, let us arbitrarily set an upper limit of $1,000,000 on the recommendations that we are allowed to make. Call these "low-cost" or "short-term" measures. They are improvements that do not require more than say, three months to complete; they do not require a major revision to the process. Other recommendations are "high-cost" or "long-term"; they are outside the scope of this discussion. Some of our "low-cost" recommendations would offer a satisfactory return on the money that they cost; the remainder would not. Now, is there some way that we can rather quickly pick out the "low-cost" measures that will show a satisfactory return and spend our time making these improvements first? Can we separate these items from those where the return is less likely to be good? I feel that we can pick some of these items quickly if we have a kiln system that has consistently non-uniform day-to-day operation. If the operation is uniform we probably cannot pick them quickly.

Jan 1, 1977

By Luttrell. G.

The profitability of coal mining operations is highly dependent on the performance of the coal blending and processing facilities. Many companies have recognized this fact and have instituted optimization programs that require large amounts of coal characterization data, extensive operational information and complex costing models. Unfortunately, this brute force approach to optimization is often overwhelming in terms of time and cost and is generally too inaccurate to be of value in day-to-day field operations. A simpler and more practical approach involves the use of ?micro-price? optimization throughout the coal supply chain. This fundamental concept assigns unit values to each type product (particle or groups of particles) passing through the production units. True optimization occurs whenever all particles with positive worth are recovered and passed to market, while all particles with negative worth are rejected. This paper describes the fundamental workings of the micro-price concept as applied to coal blending and processing operations. Several examples are also included to demonstrate the economic gains that can be realized via the application of this concept.

Feb 23, 2014