Search Documents

By Michael E. Karmis

New and developing communication systems en-able underground miners to, not only connect to the surface from an increased communication coverage area, but also to be discovered in the event of an emergency. Communication and tracking systems are required by the U.S. Mine Safety and Health Ad-ministration (MSHA) regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broad-cast devices results in a reliable communication network that can better withstand disruption in daily operation and during a time of emergencies. Research on wireless communication in mines has been ongoing since 1922, when the U.S. Bureau of Mines performed experiments in its experimental mine in Bruceton, PA (Schiffbauer & Brune, 2006a). Ac cording to Dobroski and Stolarczyk (1982), ?as early as 1922, Bureau of Mines experiments showed that radio propagation in mines was possible but not practical.? In 2006, the underground communication technologies available to the mining industry had inherent problems that limited communication capabilities. Because harsh underground mine environments significantly reduce line of sight and propagation range and introduce power and safety concerns, the overall effectiveness of underground communication technologies were limited. After several coal mining accidents in early 2006, the U.S. Congress responded with the Mine Improvement and New Emergency Response (MINER) Act, enacted

Jun 1, 2010

By P. L. Ngwenyama, W. W. deGraaf

South Africa is one of the leading producers and exporters of coal globally. A significant amount of the country’s production is obtained from previously mined underground bord and pillar workings. This coal is in the form of pillars and remnants on the roof and floor of the old workings. The good quality coal pillars were left behind as primary support during underground bord and pillar mining operations. Due to the depletion of virgin coal reserves, the pillars and remnant coal are now removed using opencast mining rather than underground methods. However, the secondary extraction of pillars and remnant coal from the old workings using opencast methods entails some serious challenges that have a negative impact on the safety and productivity of the operations, affecting both personnel and machinery. If these risk factors and challenges are managed properly, then the opencast mining operations could remove the pillars safely at recoveries competitive with those of virgin coal operations. In this study we review the recurring challenges affecting opencast pillar mining by means of field investigations and consultations with experts at five opencast pillar mining operations, and evaluate the best practices used to combat these challenges. It was found that each mine has its own unique conditions and challenges.

Dec 1, 2021

By G. M. Carrie

Introduction The subject of basic refractories is daily becoming of increased importance in metallurgical processes, and there is a constantly growing necessity for the development of better materials. This fact, together with the realization that Canada possesses one of the best sources of such refractories in the British Empire, if not in the world, made it appear? advisable that the subject be presented to the Empire Mining and Metallurgical Congress at the 1927 meeting. Having been in close touch with developments in the Canadian product during the past five years, G. M. Carrie was requested to prepare such a paper. The Canadian producers of magnesia refractories have succeeded in developing the product to a place where it has almost entirely displaced imported materials from the Canadian market. These developments were made possible by a close study of the methods of preparation of the material, and by an exceedingly careful control of the manufacturing process so as to obtain a thorough blending of the different constituents with the resultant uniformity of composition. This point is very important to the metallurgist, as un-uniform materials are a potent cause of difficulties in most manufacturing processes and the constant trend is towards their elimination. The temperature at which the Canadian material is burned ensures high specific gravity and thorough shrinkage. The grain size of the product is so controlled that the voids are only just sufficient to allow of proper bonding, thus making possible a dense, hard bottom affording high resistance to erosion and shock. Careful proportioning of the constituent elements absolutely prevents disintegration.

Jan 1, 1927

By Sven Reutzel

Investigations show that Co-based melts embedded by glass flux in a crucible can be under- cooled nearly as strong as samples processed containerlessly by electromagnetic levitation. This allows to measure magnetic susceptibility on undercooled melts while combining the use of a Faraday-balance and undercooling technique. The magnetic susceptibility of Co and Co-based alloys (such as Co-Pd and Co-Cu) is investigated as a function of temperature from superheated to undercooled state. This is done by measuring the change of magnetic force F, on a sample in a constant magnetic field Bo and an additional gradient field by means of a Faraday-balance. When liquid Co-based alloys are undercooled the magnetisation steeply rises if temperature approaches the Curie temperature. The magnetisation is measured for some Co-based alloys in liquid state as a function of alloy system and its concentration. The results show that the magnetic susceptibility of the liquid undercooled samples follows a Curie-Weiss behaviour, from which Curie temperature and magnetic moments for the liquid state are inferred.

Jan 1, 2002

By Richard L. Bullock

Believe it or not, mine evaluation and feasibility studies are as old as the industry itself. In the first recorded writing on mining by Agricola (1556), he gave several clues as what to look for in evaluating a mine, to determine if it was economically feasible. Below is the guidance from Agricola, with my interpretation of what he would include today. Now a miner, before he begins to mine the orebodies must consider seven things, namely: ? The situation (the geography/topography). ? The conditions (the geologic/mineralogic and mining conditions). ? The water (availability, hydrology and ownership). ? The roads (plus the railroads, power lines, all other infrastructure). ? The climate (the weather-rainfall/environment). ? The right of ownership (the land and legal entitlement). ? The neighbors (the social environmental concerns of the area). It is amazing how much of his guidance has not changed in 455 years. Yet Agricola gives no guidance on determining the correct cost, or determining the correct commodity pricing. But he does give a few words of caution on the related ethics involved on buying mineral properties: ?A prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him.? Three hundred years later (1866), to further amplify this point, in the most famous thing that Mark Twain never said, as an introduction to a lecturer to an audience of gold-miners at Red Dog, CA, the famed author/humorist allegedly described a mine as ?a hole in the ground owned by a liar? (Farrar & Rinehart, 1935). So, one might conclude that between these two dates, the mining industry did little to improve its reputation. Unfortunately, since Mark Twain allegedly made those remarks, we have not done near enough to gain accountability for the mineral industry.

Jan 1, 2011

By James A. Finch

"I offer a personal view of what the next 30 years holds for mineral processing. Re-stating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining -mineral processing -extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro-and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but I anticipate that the new lines will come from the waste management business. I finish by examining the ""research cycle"", identifying growth in small ""high tech"" companies and university research centres.IntroductionI have been asked to offer a personal view of""where we are going in mineral processing?"". Gazing into crystal balls is quite a cottage industry as we approach the end of the millennium. Academics are often asked to assume the role of visionary, I presume because it is considered in their mandate, to reflect and philosophize (or, less charitably, because they are considered to have the time). Since this is the 30th Annual Canadian Mineral Processors Operators Conference, I am tempted to suggest the next 30 years as my frame of reference. This is about equivalent to one engineer's career or, given it takes typically 15 years to go from concept to realization in mineral process engineering (Napier-Munn, l 997a), about 2 ""invention cycles"". With this length of cycle, much that is familiar now will remain so over the 30 years.Research and development (R&D) is in response to need. The overarching need in mining is to find new ore bodies. Process developments cannot compensate for a depleting deposit or a declining commodity price. Mineral processing R&D is characterized by incremental gains, aimed at pushing the mine down the cost per tonne league table. Breakthroughs are the exception (flotation at the turn of the century was one). This must be kept in mind when trying to predict the future in our business."

Jan 1, 1998

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining health and safety of miners. The authors evaluate potential real-time monitoring solutions for detecting and reducing diesel particulatematter, mine fires, and dust in situ, and examined the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limit. Authors review relevant documents, including research papers, trade publications, and manufacturers’ website-based information, to identify research gaps. The authors also evaluate contemporary sensors (airflow, gas, dust, silica), control system and software technologies, data transport systems, Industrial Internet of Things, ventilation network simulators, and control devices to identify potential health and safety research gaps. In this study, examples of some mines from Canada, Australia, and the USA are included where ventilation monitoring and controls have been applied. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

May 12, 2020

By AIME AIME

THE outstanding event of the past month has been the conference in Washington of the representatives of about seventy-five of the leading national, regional and local engineering and allied technical organizations." Editorial-July Journal-The American Society of Mechanical Engineers. ?Prominent engineers from all parts of the country, representing more than 75 engineering societies, with an aggregate membership of more than 125,000, participated in the organization.? Editorial-July Journal-American Institute of Mining and Metallurgical Engineers. ?Civil, mechanical, electrical, mining, heating, sanitary, chemical, agricultural, marine, refrigerating, radio, fire protection, automotive, industrial and military engineers, as well as some architects and geologists assembled at Washington, D. C. to consider the advisability of organizing a national federation capable of bringing the united efforts of the entire membership to a focus on any problem of mutual interest." American Architect, June 23, 1920. ?"the object sought places it above any engineering gathering ever held." Editorial-American Machinist, June 17, 1920. "The youngest. profession has voluntarily accepted its responsibility in human affairs and is now reaching forward to a career of essential service." "This is .unmistakably the meaning of the Organizing Conference " Editorial-Industrial Management, July; 1920.

Jan 1, 1920

By C M. Stewart

Lithium battery electric powered vehicles and machines (BEVs) continue to gain traction inunderground mining use, with predictions they will dominate the underground light and heavy vehicle fleets for some mines within the next decade. There are clear advantages for ventilation systems through reduced heat output and the elimination of harmful exhaust gases and diesel particulates. However, the risks and effects of BEV fire emergencies for underground personnel and ventilationsystems are still largely in the early stages of analysis and understanding. This paper conducts an industry review of a selection of lithium battery fire incidents and research.A research paper review on lihthium fire behaviour, intensity and toxicity will be analysed and comparisons made with equivalent diesel machinery fires for context. Guidelines for mine firemodelling parameters will be offered to assist in predicting the behaviour, heat and emissions from BEV fires, and recommendations and conclusions will be drawn on the specific hazards of lithium battery fires compared to conventional diesel powered machines.

Oct 12, 2022

By Steve T. Laflin

Since the beginning of the nuclear era, there has never been a commercial solution for the large quantities of depleted uranium hexafluoride generated from uranium enrichment. In the United States alone, there is already in excess of 1.6 billion pounds of DUF6 currently stored. INIS is constructing a commercial uranium processing and fluorine extraction facility. The INIS facility will convert depleted uranium hexafluoride and use it as feed material for the patented Fluorine Extraction Process to produce high purity fluoride gases and anhydrous hydrofluoric acid. The project will provide an environmentally friendly and commercially viable solution for DUF6 tails management.

Aug 1, 2010

Pilot plants for pressure hydrometallurgy represent special design and project execution challenges unique to the industry and to the pilot- and demonstration-scale. Pilot plant projects have different objectives and shorter timescales than commercial plant projects. Design considerations and strategies, and project execution methods that meet the special needs of pilot plant projects, are discussed. Specific guidance is given for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical process equipment, and for the selection of materials of construction for pilot-scale equipment. The balance between the need for process similarity with future commercial operations and the realities of pilot-scale equipment is also discussed.

Jan 1, 2004

"The Mine Haul Road Optimization Alliance is an Australian industry-academia collaboration which has been developed to support mine haul road operators by fully integrating mine road design research solutions with industry end-user service providers to design, assess, implement and monitor the various equipment, materials and road management strategies required to optimize the safety, environmental and economic performance of a haul road. Initially, a broad overview of the university-industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis, internationally. This insight places realization of a collaboration between Curtin University Western Australian School of Mines Mining Engineering and Metallurgical Engineering (WASM ME2) and the Haul Road Optimization Alliance (HROA) industry members into context of opportunity. Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry can collaborate to deliver a more robust solution to mine haul road design, performance or management needs, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service-providers alike forms the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and implementable solutions. The paper concludes with examples of how the alliance collaborations work in practice to deliver improved mine haul road designs and optimized operational performance, together with the mechanisms used to ensure industry needs are met through focused, end-user driven research and integrated solutions implementation."

Jan 1, 2016

By Noreen Tarac, Pablo Forgoso, Philipp Schober

A multiple use storage facility building is being developed in the Philippines on a peninsula that was reclaimed in the 1990s without any soil treatment. The subsoil now consists of loose to medium dense silty sand underlain by a soft to medium stiff clay. A liquefaction assessment by analytical methods have shown that the loose to medium dense silty sand yields a high potential for liquefaction and lateral spreading during pthe design level seismic event. To mitigate the risk of liquefaction and lateral spreading, as well as assure the slope stability of the shoreline, a solution utilizing a combination of ground improvement techniques by means of a Mixed-In-Place (MIPTM) Lattice Grid Wall and Stone Columns was developed and successfully executed. For the detailed seismic design, a Finite Element 3D analysis was undertaken to simulate static and dynamic actions on the buttress wall. The liquefaction assessment and settlement calculation were carried out based on analytical design approaches. For the execution of the Lattice Grid Wall, the Mixed-In-Place (MIPTM) method developed by BAUER Spezialtiefbau GmbH was applied. The stone columns were installed using the Wet Top Feed method.

Sep 8, 2021

By D Matthews

With the increasing demand for quality-specific ores, coupled to the reality of even more complex minable iron ore reserves, there is a growing need for real-time online material analysis of plant feed and product. For a full system mass balance, the combination of conveyor weight scales, flow and density transmitters are required. This alone does not guarantee product grade. For optimal process control and material blending, real-time online elemental scans in combination with the mass weighting is becoming more than a ‘nice to have’. These elemental scans located at key positions, enable the mining and plant operators to make informed decisions timeously, therefore ensuring product outcomes and optimising operations where material grade and the control thereof are important. Typically, these units follow the mining and primary crushing circuit as well as on the product conveyors, low-grade conveyors and tailings lines. Deployed after the primary crushing circuit, an analyser acts twofold:1. guaranteeing mining production, and2. processing facility feed blends.The analysers on the product conveyors guarantee saleable product. The analysers on the low-grade conveyor and tailings line complete the elemental balance and identify the potential of the low-grade and tailings for future processing. The system losses (accumulation) are calculated to determine the amount of material ‘lost’ during the processing stage which does not report to any of the aforementioned and can be used as a measure of the efficiency of the plant. A further advantage of the real-time online analysis of material is that immediate intervention can be taken in the event that the product is not of saleable product grade requirements. In the Khumani Iron Ore mine, Northern Cape, South Africa, run-of-mine (ROM), product and control analysers were included. Run-of-mine and product stockpiles are certifi ed, low-grade material is not currently directly measured, but calculated from the internal control loops. Iron units are reconciled between product and feed material.

Jul 11, 2011

By Orica

Unlicking the Possibilities ISEE Digital Detonator Workshop New Orleans, LA Wednesday, February 4, 2004

Jan 1, 2004

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

The introduction of computer technology to the mining industry has produced many benefits for the mining engineer. The most significant is the dramatic increase in productivity realized by the individual user. This is important during times of competitive market conditions. Software for the minerals and energy industries has evolved substantially over the past decade. But even today it remains difficult to find a system that features the flexibility and integration capabilities to effectively (and cost-effectively) handle the needs of professionals in each phase of the mining industry - from exploration to reclamation. Several national software developers are now addressing this challenge. One Denver-based company, MINEsoft Ltd., offers a software package that is currently being used in each phase of the mining industry. The basic technology used in MINEsoft's database management system was developed in the 1960s. But during these early years of the computer industry, most of the technology was available only on mainframe computers, and then only as separate entities. MINEsoft's system unifies these various systems in one package that can be used on most computers manufactured today. Database Management System TECHBASE is a flexible, integrated database management system designed specifically for technical applications. The system features a database manager with no practical limit to the amount of data it can store, retrieve, and manipulate, according to the company. TECHBASE in¬cludes Applications Packages (TAPs) designed to meet the needs of professionals in a host of industries. Clients use the TECH BASE system to prepare many reports, including important EPA information. The package reduces data to a manageable level and enables users to increase productivity with a smaller staff. Mining engineers no longer need to do things by hand. What used to be a day's work can be accomplished in an hour or two. Exploration "Using the TECHBASE system to generate maps has probably saved us the expense of three or four draftsmen," says Ralph Fitch, regional manager and senior staff geologist with Chevron Resources in Portland, ME. "The system has great flexibility. You can treat it much like a spreadsheet. If you are halfway through with a particular project, the system allows you to add fields and calculations with ease but without starting over." Fitch uses TECHBASE for the "straightforward" plotting of results and generation of geochemical and geophysical profiles. "In exploration," he says, "these are the two key elements ... the generation of maps and data profiles. The system allows you to plot as many elements and variables in these areas that you like." Other aspects are important, too, says Fitch, including drill hole sections. "We use all the basic capabilities the system provides in the complete package," he explains. "When shopping for a system, TECHBASE was clearly dedicated to exploration in the

Jan 9, 1987

By G R. Ballantyne, M S. Powell

A comprehensive Australia-wide survey of comminution energy consumption at copper and gold mines was presented by the authors at the 11th AusIMM Mill Operators’ Conference 2012. The database has been extended to include major overseas mines and used to benchmark comminution energy consumption across the industry. The mines included in this study now represent 15 and 24 per cent of the total global gold and copper production respectively, and almost all Australian production. The comminution energy intensity per unit of saleable metal has been presented in a graphical form similar to a cost curve used in economics. The graphical method has been developed to assess the competitive advantage that can be achieved by reducing comminution energy intensity.This benchmarking tool has been applied to three published case studies to assess its applicability. The first case study indicated that a large reduction in size-specific energy (kWh/t -75 µm) was achievable by converting standard semi-autogenous and ball mill circuits to include high pressure grinding roll and stirred mills. The second case study investigated the metal-specific energy reduction historically achieved by Bougainville with the addition of a preconcentration screening plant. The final case study was conducted by Barrick Gold Corporation and involved incremental efficiency upgrades at three of its gold mines: Cortez, Cowal and Mara North. The application of the benchmarking tool to each of these case studies successfully demonstrated the scale and competitive advantage that was achieved by reducing energy intensity.CITATION:Ballantyne, G R and Powell, M S, 2014. Benchmarking comminution energy consumption for improved efficiency, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

This report is a compilation of all information obtained in accordance with the requirements of contracts S0122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies: Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gai-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated

Jan 1, 1974