Search Documents

By Fred D. Wright

Some new equipment for drilling vertical holes, cleaning blast holes, hauling explosives, and conditioning Diesel exhaust gas has been developed. at the Bureau's Experimental Oil-Shale mine near Rifle, Colo, The equipment has application, not only in oil-shale mining, but in many of the country's underground mines in which room-and-pillar methods of mining are employed. This report presents the Bureau's experience in testing the following equipment in the Experimental Oil-Shale mine: 1. A four-drill benching jumbo for drilling 23-foot vertical blast holes 2. A jet borehole blower for efficient cleaning of deep, vertical blast holes. 3. An explosives truck equipped with two compartments to provide safe conveyance for dynamite and detonators. 4. A mobile, electric substation to provide switching equipment, low-voltage and overload protection, and transformer facilities to remote locations in the mine. 5. A chemical conditioner for scrubbing the exhaust gases from Diesel-powered equipment used in underground operations. 6. Other units of equipment which have been tested at the Experimental mine.

Jan 1, 1951

By A S. Derrington

High-accuracy, solid-state digital reference barometers have proven to be well suited to conducting underground barometric pressure surveys. The only problem is their expense; at least A$4000 each. For this reason, and because barometric pressure surveys are not a routine undertaking, very few mines have been able to justify the purchase of suitable instruments. The author knows of only three Australian metalliferous mines that own them.However, this may soon change given the recent development of low-cost, mass-produced miniature barometric pressure transducers. These transducers were developed to provide an altimeter function in the latest generation of smartphones. The main purpose of the inbuilt altimeter function is to allow the smartphone to be aware of its altitude when the global positioning system satellite signal is lost.This paper describes a prototype barometer that was constructed using one of the most accurate of the latest generation of piezo-resistive smartphone barometric pressure transducers. The prototype instrument was constructed for less than five per cent of the cost of a commercially available digital reference barometer. The prototype was subsequently tested against a reference barometer at the University of Queensland’s Experimental Mine to verify its accuracy and suitability for measuring pressure differences between underground survey stations.It is expected that the instrument’s low cost will pave the way for barometric pressure surveys to become more commonly used in mines. In turn, the resulting improvement in knowledge of major underground pressure losses should allow mine ventilation officers and engineers to optimise their ventilation systems and potentially reduce overall operating costs.An alternative option would be to use a barometer-equipped smartphone as a survey instrument, provided that its inbuilt barometer module is sufficiently accurate.CITATION:Derrington, A S, 2015. Development of a low-cost instrument for barometric pressure surveys, in Proceedings The Australian Mine Ventilation Conference, pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

A new horizontal borehole packer for use in coal beds has been developed. This packer utilizes a principal of operation which has not previously been used. The resulting packer is less costly to purchase, can be easily repaired in the field with inexpensive expendable parts. This report describes the development and testing of the new packer and the evaluation of commercially available packers.

Jan 1, 1971

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

By Robert F. Chaiken

The U.S. Bureau of Mines conducted an experimental and theoretical study of coupled chemical kinetic and mass transport processes during leaching of pyrite from coal in a counterflow, "trickle-bed" column reactor. Spatial and temporal data on reactant and product concentrations were used as solutions to appropriate continuity equations, which in turn define chemical kinetic reaction rates. Data from four 180-by 30-cm column leaching experiments using coal, coal waste, and air-water and air-FeC13 lixiviants have been analyzed. The rate of leaching was found to be diffusion limited (probably by Fe3+) and not controlled by bacterial action. Rates of pyrite oxidation were found to vary with elapsed time (80 to 225 days) and followed a bell-shaped curve, sometimes with a delay before start of reaction. Maximum rates of reaction ranged from 3 to 10 (mmol/d)/L (column) for coal waste and 0.4 (mmol/d)/L (column) for coal. Reaction was 30 to SO pct complete, probably due to precipitation of product salts (e.g., jarosites), which impede transport of oxidant through the coal. An absorption-desorption model of solids leaching, which considers the role of heterogeneous porosity in solids leaching, was used to describe time-dependent leaching rates.

Jan 1, 2010

By Gordon R. Harris, Raymond Chalk

Descriptions of typical pulp and paper manufacturing processes are presented, with particular emphasis on the use of minerals and derived products. Some consideration is given to the future demand for these minerals by the pulp and paper industry. Possible influences of techno-logical change and social legislation are suggested and their effect on saltcake demand by the pulp industry is discussed. Predictions are made regarding trends for new and existing paper products.

Jan 1, 1968

By R C. A Minnitt

The Witwatersrand Supergroup is host to the world’s largest gold deposits. The location, quantity, grade, continuity and other geological characteristics of a Mineral Resource are either known, estimated from specific geological evidence and knowledge, or interpreted from a well constrained and portrayed geological model. Establishing such a model is an integral part of the evaluation process in the Anglogold Ashanti (AGA) group, and is referred to as a Geoscience Business Model for the mining operations. The geological model established over the years has relied on detailed descriptions of the mineralisation, and understanding of the regional and local geology of the Witwatersrand sediments, in the West Wits and Free State goldfields. The processes of data collection in regard to underground stope and developing mapping, structural and sedimentological mapping, and the geological inputs to mine planning systems are described, together with aspects of drilling, sampling, grade control, and data management. Anglogold Ashanti’s Geoscience Department employs a complex and unique process to generate the Mineral Resource, including a 3D geological structure model of the orebodies which are usually highly faulted, and a robust mineralisation/facies model on which the decisions about domain boundaries are established. A Mineral Resource Inventory System (MRIS) has a dynamic graphic interface to the resource database that is used for compiling the resource statement. It is also used to determine the gold-called-for, as well as short and long-term planning. A unique estimation process using the extensive closely spaced stope face sampling database and the more widely spaced surface drilling information is used in combination in the Macro Co-Kriging estimation. The use of different support sizes in the C0-Kriging process is preceded by the equally unique ‘clusterisation’ and ‘acceptorisation’ procedures by which the data are quality controlled and assured prior to their use in the kriging process. The Mineral Resource and Ore Reserve estimates are classified according to the SAMREC code through a method that ensures that they are compliant, auditable, transparent and reconcilable with previous Mineral Resource and Ore Reserve statements.

Aug 22, 2011

By L. H. Van Loon

INTRODUCTION THE property of Madsen Red Lake Gold Mines, Limited lies between Russet and Faulkenham lakes in Baird and Heyson townships, district of Patricia, Ontario. It is about six miles south west of the town of Red Lake, with which it is connected by an all-weather road. All orebodies found to date at the property are silicified lenticular bodies which lie within tuff beds. The ore bas a specific gravity of 2.95. It consists of mica and chlorite schist, silicified and containing a considerable amount of disseminated carbonate, and mineralized with pyrite, pyrrhotite, magnetite, arsenopyrite, and chalcopyrite. Of these, pyrite, in coarse to fine disseminated grains, is by far the most abundant. Pyrrhotite occurs in ?the gangue material as medium to fine disseminated grains. A very small amount of arsenopyrite, in small crystals, is associated with the pyrite, and small grains of chalcopyrite occur in both gangue and pyrite. Although some of the gold present in the ore is quite coarse, a good deal of it is extremely fine.

Jan 1, 1951

By C. J. Huffman

MAGNESIUM alloy tubing and hollow shapes are finding increasingly wider usage in practical applications today. Square and rectangular tubing and hollow shapes find [ ] greater diversification in use than standard round tubing. Typical applications are roller conveyors, ladder rungs, spools, furniture, tank car loading tubes, athletic equipment, and business machine parts. In general, the amount of tubing and hollow shapes produced represent a minor portion of the magnesium extrusion business. The magnesium alloys in which tubing and hollow shapes are being produced together with typical properties are presented in Table I. MI A alloy is a low cost alloy possessing good welding and stress corrosion characteristics together with moderate formability and corrosion resistance. It is widely used for low strength applications. AZ31 B, alloy is used for moderately stressed applications and possesses good corrosion resistance and formability with fair welding characteristics. AZ61 A alloy has slightly higher physical properties than AZ31 B alloy together with good formabil- [ ] ity and corrosion resistance but slightly poorer welding characteristics. AZ80 A, ZK60 A-F, and ZK60 A-T5 alloys are used where the maximum in physical properties is required. AZ80 A alloy possesses fair corrosion resistance but with formability and welding characteristics inferior to' the other alloys. ZK60 A-F and ZK60 A-T5 alloys, while only recently offered for com¬mercial use, are finding favor due, to the higher permissible extrusion rates. These alloys possess greater toughness than AZ80 A alloy and, while of moderate formability at room temperature, are very formable at 300° to 500°F. The major portion of tubing and hollow shape production at the present time is in AZ3I B alloy. Magnesium alloy tubing is commercially available in the as-extruded condition or, in the case of ZK60 A-T5, in the as-extruded and aged

Jan 1, 1951

By J P. Sykes, A Trench

"World-class mine projects are increasingly failing to become world-class mines. Non-technical, socio-political and environmental problems seem, in part, to be the cause. However, the intangible and qualitative nature of these problems means overcoming them will require a greater systemic understanding of how the various technical and non-technical factors interact. This is particularly important as the concept of sustainable development has changed the industry paradigm sufficiently that it is no longer clear what world-class means. Finally, this better systemic understanding of mine projects needs communicating back to the exploration sector to improve exploration targeting.However, a disconnect between the exploration and mining sectors and between geologists and mining’s other professional disciplines means this is currently not possible. The use of economic evaluation techniques to assess the risk and value presented by the various technical and non-technical factors can assist with this by giving the varied professions a common language and including inputs from all disciplines. This paper therefore suggests a theoretical framework for analysing the various technical and non-technical factors, particularly the most challenging intangible and qualitative ones, and incorporating them into the typical economic evaluation techniques used in the mining industry.Understanding the risk and value relating to both technical and non-technical risks, however, places a greater emphasis on mining geologists to be conversant with a wide range of disciplines. Mining geologists will have to develop three types of knowledge:focusedinter-disciplinarybroad. In addition, they will have to become systemic thinkers to connect these types of knowledge. This multidisciplinary approach will require the use of fundamental critical thinking skills, common sense, intuition, experience and quantitative modelling techniques, dependent on the situation. As a result, both companies and professional societies, such as the Australasian Institute of Mining and Metallurgy, will have to develop ways of improving mining geologists’ inter-disciplinary and broad knowledge.CITATION:Sykes, J P and Trench, A, 2014. Resources versus reserves – towards a systems-based understanding of exploration and mine project development and the role of the mining geologist, in Proceedings Ninth International Mining Geology Conference 2014 , pp 243–270 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By O`Donnell. P. J.

THE modern coal cutter is a highly developed, and to a certain extent a somewhat complicated, machine. The requisite power to cope with conditions as found must be generated by the motor with due regard to limitations in the matter of dimensions and weight. This imposes the necessity of relatively high speeds of rotation. Any factor external to the machine proper which tends to reduce the load on the motor and gearing is most important. Experience has proved that close attention to the question of cutter-chain details undoubtedly results, in practically every coal-cutting operation, in increased efficiency and reduction of power and maintenance costs. The chain is the unit of the coal cutter which most greatly affects the economical operation of the machine, and only by due consideration of conditions and by the proper selection of the right chain can best results be expected; also, intelligent care of the chain while in operation is essential if it is to give its best service. The chain is the part of the machine that carries the pick boxes or blocks, which are connected to each other by a pair of chain links. The power to drive the chain is trans-mitted by a sprocket. The chain runs in guides supported by a rigid member called a 'jib'. Figure 1 shows the various parts mentioned. The first requirement of a chain is that it cut the coal as fast as possible. The second is that it do so economically. Economy of cutting can conveniently be divided as follows: (1) Economy in power used. (2) Economy in pick life. (3) Economy ' in chain life. ( 4) Economy in jib life. (5) Economy in labour for maintenance.

Jan 1, 1936

By J. A. Bos, Z. Dai, P. Quinn, A. Lee

A flowsheet is being developed for processing Thompson ultramafic low-grade nickel ores. This type of ore is characterized by high content of serpentinized magnesium silicates which generate slimes during comminution. Flotation of this type of ore proves difficult due to problems associated with the slimes. The flowsheet, based on extensive laboratory and miniplant flotation tests, consists of two key components: desliming by hydrocyclones prior to flotation and using soda ash for pH control in flotation. Satisfactory metallurgical results have consistently been achieved in laboratory full circuit simulation and miniplant tests.

Jan 1, 2009

By V. F. Parry, W. S. Landers, John B. Goodman

"INTRODUCTION The object of this investigation was to demonstrate a satisfactory method of storing slack subbituminous coal in open pits in a manner,that would minimize the cause of the physical deterioration and would have a practical application.The storage of coal by industrial plants is to their advantage, since an adequate operating supplying of fuel is available at all times as insurance against transportation delays, shortages, and strikes. Furthermore, it is possible to participate in low seasonal freight rates and mine costs by permitting the railroads to utilize idle equipment and by taking advantage of the off-peak production at the mines. For a number of years, one of the larger beet-sugar companies operating in the Rocky Mountain region has taken advantage of the lower prices and seasonal production of subbituminous slack coal during the summer months and purchased a large proportion of its requirements for the annual winter campaign. This company, operating sugar-refining plants in the 1943 campaign, used 256,613 tons of subbituminous coal. Of this quantity, 166,636 tons was purchased during the off-peak season and stored for use during the winter. It is the practice of this concern to place coal purchased through the months of January to October in underwater storage for use in the beet-sugar campaign, which lasts from October to as late as, January. The beet-sugar refining ""campaign"" period starts immediately after the beginning of the beet harvest and lasts 60 to 70 days."

Aug 1, 1946

By Willard C. Lacy

INTRODUCTION A program to insure adequate talent for development and management of our mineral resources entails two equally important and interrelated aspects: 1) attracting and retaining promising student talent, and 2) providing a first-rate education for those entering careers in mineral science and engineering. Manpower shortages have eased in many areas of engineering, particularly in those areas dependent directly or indirectly upon government contracts in space and war programs. However, in the minerals industry the needs still remain critical. As increasing concern over preservation of the environment has developed, the political and social reaction was to seek out major offenders, to look for "whipping boys" -- and the mineral industry was, and had been, an offender. It was there for everyone to take pictures, it couldn't be covered up, and the Department of the Interior lashed away in the beautiful and popular brochures: Quest for Quality, The Third Wave, The Population Challenge, and Surface Mining and Our Environment (Ravaged Land). The Sierra Club, the Field and Stream magazine, TV, and daily news media added their lashes. In the minds of our social-conscious youth the mineral industry took on the image of "exploiters" of natural resources; "polluters" of streams, lakes, and the atmosphere; "despoilers" of wilderness areas and scenic beauty -- a plague to combat, rather than an exciting challenge that entailed exploration of the remote, conquering of the primitive, and developing of the undeveloped. Enrollments declined and many traditional mineral engineering curricula were abolished or Integrated into other stronger engineering departments to meet student-faculty ratio requirements.

Jan 1, 1971

By M. L. Glenn

The Bureau of Mines is conducting research on substitutes for chromium-containing alloys in order to conserve imported critical and strategic materials. Part of this research concentrates on finding low-chromium substitutes for heat-resisting stainless steels for the temperature range 600° to 800° C. Ferritic alloys are emphasized that have oxidation resistance provided by chromium contents as low as 10 pct and stress rupture strength provided by the precipitation of the chi(X)-phase intermetallic compound, (Fe36Cr12 (Mo, Ti)10). Initially, research was concentrated on selecting an alloy composition having a minimum chromium content with strengthening provided by the X-phase. An Fe-(10-12 pct)Cr-6 pct Mo-(1.5-2.0 pct)Ti alloy was selected. After the alloy selection, the tensile, stress rupture, and oxidation properties were determined. Stress rupture properties were found to be similar to those of 304 stainless steel. However, the alloys possessed brittleness during both stress rupture and tensile testing, possibly as a result of too high a content of molybdenum and titanium. Higher than expected oxidation rates were found that may be caused by the high molybdenum content.

Jan 1, 1984

By McMillan W. D.

Vermiculite is the name of a group of micaceous minerals characterized by their property of exfoliating when heated and thereby increasing many times their original volume. The resulting product has excellent heat-and sound-insulating properties, is used as a lightweight aggregate, and has numerous other industrial applications. Deposits of vermiculite occur in areas of pre-Cambrian rocks of the Llano uplift of central Texas, particularly in Burnet and Llano Counties. Because of the growing economic importance of vermiculite products, the Bureau of Mines undertook a detailed investigation of several deposits in Llano County. This investigation was completed in February 1947. The work comprised topographic surveys of five deposits, drilling with a 4-1/4 inch Parmanco power auger drill, and laboratory evaluation of samples. 342 drill holes, aggregating 4,905.5 feet, were completed, and 377 samples were taken. Laboratory evaluation of the vermiculite comprised expansion tests on both crude and beneficiated samples. The products obtained were compared with commercial-grade vermiculite from Montana.

Jan 1, 1949

By R Sterk, B Reid

The Konongo Gold Project is located on the western margin of the 125 Moz Ashanti Gold Belt in Ghana, West Africa. It is situated 60 km along strike of the world-class mineral system at Obuasi and is interpreted to lie on the same controlling regional shear system.The project is operated by Signature Metals, a subsidiary of the Liongold Corporation, and is managed and funded by the Liongold Corporation.Historic underground operations at Konongo produced 1.6 Moz Au at a head grade of 11.8 g/t Au, from eight operations spread along 16 km of the shear system. Mining focused almost exclusively on free-milling gold in quartz, ignoring the gold-bearing sulfide mineralisation associated with the quartz veins. Underground mining ceased in 1986.In 2013, Signature Metals re-focused the program at Konongo to assess the viability of mining the sulfide ore sustainably. This led to the first campaign review of the historic underground data and resource potential since mine closure. The Obenemase mine was the first of the eight operations to be assessed as part of this campaign.Large amounts of legacy data have survived for Obenemase and several historic resource estimations have been completed based on these data. The data typically consisted of hand-drawn sections and plans, and ledgers of commonly incomplete drilling and sampling data. Some drill core have been lost over time, but a large amount of quarter-core and half-core as well as pulps and rejects are still available. Previous resource estimates had a low confidence value because all the available assay and geological data were integrated effectively with the estimates, resulting in a lack of understanding of both grade and geological continuity.This project built a new geological model for Obenemase that greatly enhances the understanding of the controls on mineralisation using a thorough approach of re-surveying, re-cataloguing and re-logging. This model led to an increased degree of confidence and a subsequent upgrade of resource classification, and created several previously unrecognised strong exploration targets. The resulting resource estimates increased the value of the project by 100 per cent.This paper emphasises and highlights the importance of a well-understood geological model on the confidence of a resource estimate and how this may directly impact on the project’s ‘bottom line’.CITATION:Sterk, R and Reid, B, 2014. The Konongo Gold Project, Ghana – an example of how geology makes all the difference to a resource estimate, in Proceedings Ninth International Mining Geology Conference 2014 , pp 467–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Finlay, J. S.

THE North Lily Mine started its career in an unusual way it was discovered by a geologist. The remarkable circumstance of driving a 2400-ft. drift into an unexplored country and "hitting her on the nose," indicates that geologists are sometimes numbered among those whom the Lord loves. Diamond- drilling from surface had previously shown the presence and position of the Ophir beds, and surface showings of pebble-dykes, faults, and bleached rhyolite indicated conditions similar to those at the Tintic Standard "Pot-hole." The discovery drift from the Tintic Stand- ard 700-level reached the North Lily orebody in January, 1926, and development and stoping were continued by Tintic Standard men and equipment until the North Lily shaft was sunk and put into service in May, 1928. The discovery drift was run on a cooperative basis by the Tintic Standard and North Lily mining com- panies. Finding the North Lily mine cost the North Lily company $26,000. The Tintic Standard Mining Co. furnished men and equipment to drive this discovery drift at a fraction of what it would have cost to find the orebody from surface. This was the beginning of the friendly cooperation that still exists. Through Tintic Standard ground the Tintic Standard paid two- thirds of the cost and the North Lily one-third; the cost of the drift through Eureka Lily, into North Lily ground, was paid by North Lily. Later, another drift from the Tintic Standard 900-level was run on the same plan, excepting that Eureka Lily paid its share of the cost; that is, the Eureka Lily paid one-third of the expense in Tintic Standard ground, and the Eureka Lily two-thirds and North Lily one-third in Eureka Lily ground. This 900-drift was driven by North Lily from the Eureka Lily line to near the North Lily west side-line. From this point the Chief Consolidated continued the drift well into Tintic Bullion ground.

Jan 1, 1929

By C. Hendricks

This paper is based upon field studies conducted in a western Canadian open pit coal mine. This work has involved the adaptation of microprocessor-based instrumentation to monitor various operating parameters on-board blasthole drills and mining shovels. A review of instrumentation and monitoring methodology will first be presented. Based upon experience from field-based studies, the paper will subsequently focus on the application of monitoring technology within the framework of an integrated Equipment Monitoring System. Such a system will permit the real-time performance evaluation of key equipment involved in surface mille production.

Jan 1, 1991

By Williams, J. A.

THE Alaska Juneau mine has been developed through an adit driven at the elevation of the top of the mill and all mining is done above this main haulage level. As a result of wholesa1e"mining operations about 11,000 tons rock containing one dollar' per ton in gold is, hauled to the. concentrator during every 24 hr. Due to the method of mining, whereby a system of oreways delivers-the.ore direct from the stope to the bottom level of the mine, no tramming of ore is done on any of the upper levels. However, ;in doing exploratory drifting and crosscutting on the upper levels, the broken material is trammed by hand in 1-ton 18-in. gage cars to a nearby raise connecting with one of the several oreways. This constitutes the only tramming operation except that on the main level.

Jan 1, 1931