Search Documents

By R. F. Tenney

The performances of four anthracite-burning stokers have been observed under identical 74-hp. steam boilers. Fifty runs of 12 and 24 hours' duration were made in accordance with the test code of the American Society of Mechanical Engineers (ASME). The capacity of each stoker for burning anthracite has been determined, the heat efficiency at each fuel rate has been computed, and the various significant items of hear loss have been estimated. The operating data and results from each run are tabulated in this report in the form used in the test code. The heat efficiencies and most significant operating data for each run are also presented graphically for each stoker to establish the trends with increasing boiler outputs, The tests show that rice anthracite can be burned on stokers adapted to its use at heat-conversion efficiencies of 82 percent or more under continuous firing. These high efficiencies are maintained with fuel inputs 30 percent higher and lower than the peak efficiency rate. Moreover, a heat efficiency of 70 percent or more is obtained at 50 percent of the optimum fuel rate, even though the excess air into the furnace cannot be held below 150 percent.

Jan 1, 1960

By M. E. Tyrrell

This Bureau of Mines investigation was made to determine the possibilities of using Florida beach-sand concentrator wastes in ceramic products. Sands used in the investigation originated in the Trail Ridge area of Florida, where continued operation of processing plants for recovering titanium minerals promises a dependable source of raw materials. Three general classes of ceramic products were studied, namely: (1) Structural, (2) refractory, and (3) electric-furnace slags.

Jan 1, 1956

By R. W. Van Dolah

The Bureau of Mines t.ced its investigations into sympathetic detonation of ammonium nitrate (AN) and ammonium nitrate-fuel oil (AN-FO) to define the scaling law for safe separation from detonating AN-FO. Both missile- and non-missile-producing AN-FO donors, weighing up to 5,400 pounds, were employed with acceptors of the same size. The usual cube-root scaling law was not confirmed; exponents for the relationship S = f(Wx) for AN were 0.51 with non¬missile-producing donors and 0.61 for missile-producing donors. For AN-FO an exponent of 0.80 was indicated in the missile-producing case. AN-F0 in polyethylene bags appeared somewhat more easily initiated than bulk AN-FO. The efficacy of barricades in protecting AN charges was investigated. detonation distances were reduced from one-third to one-seventh when filled barricades were employed. The investigation was extended to dynamite with both types of donors. With 1,600-pound missile-producing donors and an equivalent weight of dynamite, initiation would be expected in 50 percent of the trials at 167 feet. The corresponding value in the non-missile case was 67 feet. The data developed in this program of sympathetic detonation will allow the development of a rational set of safe separation distances for AN, AN-FO, and explosives.

Jan 1, 1966

By Rowena Anderson

Mining companies are now looking for more effective ways to engage the community in public participation. Consensus-based approaches are becoming the most popularly applied way of achieving meaningful public participation. This paper introduces the principles surrounding consensus-building approaches and the processes for getting them started. The Healthy Communities Movement is one such consensus-based approach that offers a well-established holistic model for conceptualizing a healthy sustainable community. It also highlights the importance of public participation as an essential component of achieving a sustainable community. The paper concludes by illustrating how current company-community relations programs can utilize these models.

May 1, 2002

By M. R. Geer

American and European practices in cleaning fine coal are strikingly different. The tables, launders, classifiers, and pneumatic devices used in America are seldom employed in Continental Europe, where much of the fine coal is cleaned in feldspar jigs, often supplemented by froth flotation of the extreme fines. This difference in choice of cleaning equipment may be fortuitous, but in large measure can be attributed to a difference in economic factors. Coal being more costly in Europe, there is greater emphasis on efficient cleaning of all sizes, including the extreme fines, and it is common to produce a high-ash middling for "on-site" consumption to avoid any waste of fuel value. The feldspar jig has been found advantageous under these conditions. In the United States fuel coal must be prepared as cheaply as possible, and metallurgical coal must be prepared as efficiently as possible; thus in both branches of preparation practice, any cleaning device that promises greater economy or higher efficiency warrants consideration. The feldspar jig, as employed in Europe, has a much higher unit capacity than the wet table used so extensively here and therefore offers economy in the capital costs of a washery through saving in space. As pointed out by Vissac,4/ the jig operates under automatic control, and therefore can cope with fluctuations in quality of feed. Maintenance costs for a single, large-capacity unit, such as the feldspar jig, would be expected to be lower than those for a battery of low-capacity cleaners. These considerations led the Bureau of Mines to undertake an investigation of the feldspar jig to determine its possible usefulness in this country.

Jan 1, 1958

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1952

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

By W. L. Saunders

(Wilkes-Barre Meeting, June, 1911.) I. INTRODUCTION. IT is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel was the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 miles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in. one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of France to the frontier of Hungary, between Italy and the plains of southern Germany. The contour

Jul 1, 1911

By D G. Boxall

As an alternative to heavy water cooling, reactors cooled by organic liquids are being actively developed in Canada under the sponsorship of Atomic Energy of Canada Limited. One of the areas in which development has been required is that of core materials. The factors affecting the selection of fuel canning and coolant tube materials are discussed. It is shown that S.A.P. is a potentially attractive material for these applications. The fabrication of fuel sheathing is discussed. Difficulties met due to large inclusions and blistering due to high hydrogen contents have been overcome by magnetic separation and vacuum sintering of the powders. High-quality tubes can now be produced by extrusion to finished size. A study has been made of the mechanical properties of fuel-sheathing tubes and bar stock. The stress rupture properties of the tubes subjected to uniaxial and biaxial stress have been determined. The biaxial stress tests were performed by internal pressurization. For times in excess of about 200 hours, the curve of stress against time to rupture is extremely flat. The secondary creep rates of

Jan 1, 1965

By Duane L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry and presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a United States Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) utilizes the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package utilizes a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgement scheme that provides an effective method of identifying problem areas which may exist in the mine network. The package was written in Fortran for a 64 kilobyte, Z80-based microprocessor-computer.

Jan 1, 1984

By Osvaldo A. Bascur, Curt Heftier

The lack of integrated information including the Energy/Utility Suppliers with sufficient detail for analysis causes inefficient operation in metallurgical complexes including the Energy/Utility Suppliers . Defining the right context for information use is essential for sustainable operations. This being said, what are we doing to enable people to act upon information and to be aligned to optimize the use of resources like raw materials, energy, water and consumables for an entire metallurgical complex? Collaboration between all company entities is a key component of improving efficiency. Evolution of web technology and object modeling of enterprise assets enables collaboration across the whole business. Operational troubleshooting occurs more quickly as the organization acts on issues to reduce wasteful operation. This paper presents a real time software infrastructure with tools that give users the ability to sift through available data, transform data into information for business continuous improvement and optimization. We will introduce a new technology for analyzing real time data, information and events using multidimensional analysis of information to detect anomalies based on the statistics of the data classified by time events to reduce the information into action. A new paradigm for collaboration at a local and strategic level is proposed to enable the enterprise to become proactive in dealing with wasted time and products. Three examples from the industry will presented and their benefits highlighted.

Jan 1, 2011

By Dewey W. Geary, Rachael V. Bisnett, R. Michael Bivens, Thomas G. Andrews

"The powerhouse for the Red Rock Hydroelectric Project is being constructed at the toe of the existing U.S. Army Corps of Engineers’ Red Rock Dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends though overburden and 40 feet into rock. Prior to rock excavation, a grouting was performed around the excavation for the purpose of increasing the strength of zones of fractured rock. For the majority of the perimeter, the rock was fairly tight and grout takes were relatively low. However, for a 160 foot extent along the landside of the excavation, extensive grouting was required to treat a two to five foot thick zone characterized by artesian flows from grout holes on the order of 20 gallons per minute (gpm) or higher from a voided zone in rock that was partially filled with sand, clay, and rock fragments. This paper discusses the treatment measures used to fill and improve the strength of this zone, which ultimately entailed a combination of thick cement grout and polyurethane grout, holes spaced as close as 18 inches on-center, and two additional rows of grout holes.IntroductionThe Red Rock Hydroelectric Project (Project) is currently under construction at the existing U.S. Army Corps of Engineers’ (USACE) Red Rock Dam on the Des Moines River near Pella, Iowa. At peak generation, the Project will generate up to 55 MW with an average annual energy output of 178 gigawatt-hours.The powerhouse for the Project will be located at the toe of the existing dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends up to a depth of 40 feet into rock through the St. Louis Limestone and terminates in the Warsaw Limestone. Prior to rock excavation, grouting was performed around the excavation for the purpose of improving the strength of zones of fractured rock. An auxiliary benefit of the grouting was reducing seepage into the excavation. Grouting began on July 20, 2015 and ultimately concluded on September 26, 2015.Drilling and grouting occurred as planned on the riverside (southwest) of the excavation along the cellular cofferdam and stilling basin wall (grout holes P-1 through S-13) and on the upstream (northwest) side of the excavation along the secant pile excavation support wall (grout holes P-14 through S-19) (refer to Fig. 1). The rock in these areas was generally tight with relatively low grout takes. However, on the landside (northeast) of the excavation (grout holes P-20 through P-28), partially infilled voids and artesian flows were encountered during drilling generally between depths of about 28 to 40 feet."

Jan 1, 2016

By J. Christophe Niyonzima, Ekata Emmanuel Edo, Sayaf Mustafa, Liqun Luo

Iron and manganese both are important ferrous metals, and they usually need to be extracted separately for better usage. Ferromanganese ore from the Yunnan Province of China was investigated by subjecting it to reduction roasting, leaching, magnetic separation, hydrometallurgical separation process, X-ray diffraction (XRD), electron probe micro-analysis (EPMA) and scanning electron microscopy/energy-dispersive spectroscopy (SEM-EDS). It is noted that the ferromanganese ore contains valuable components or elements of 21.41 wt%Fe2O3 and 19.88 wt%MnO, which are 14.99% and 15.40% of the total of Fe and Mn, respectively, with a large amount of impurities comprising 33.00 wt% SiO2, 9.81%wt%Al2O3, etc. After roasting, microscopic examination showed the presence of haematite, magnetite, pyrolusite, psilomelane, hollandite, marcasite, pyrite, limonite, braunite and manganite, while XRD analysis showed that the magnetite content increases with the increase in roasting temperature, reflecting the increase in conversion of haematite to magnetite. Based on EPMAand SEM-EDS analysis, it was shown that the haematite and magnetite interface were the main Fe-bearing minerals; however, the dissemination of the two minerals, that is, haematite andmagnetite with the coexistence of Fe- and Mn-bearing minerals, will result in difficulty in effective separation of Fe and Mn. The effective roasting temperature and roasting time were 800 °C and 60 min, respectively, to avoid the formation of a composite oxide of MnxFe3-xO4 beyond 800 °C. The Fe recovery via roasting and magnetic separation only was 66.56%, whereas a combination of magnetic separation which ensued after the leaching process showed a recovery of 80.08% and 59.95% of Fe and Mn, respectively.

Mar 26, 2021

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The separation of fine mineral particles, especially using environmentally friendly approaches, is one of the main problems in the processing of low-grade ores and the re-processing of mining tailings. This work assesses the potential of biosurfactants as collectors in the flotation of ultrafine (smaller than 20 μm) particles of hematite and malachite. As biosurfactants, we test acetylated acidic (ac-ASL) and lactonic sophorolipids (ac-LSL). In addition, n-dodecyl-β-D-maltoside (DDM) is used as a model non-ionic alkyl disaccharide surfactant, and sodium oleate (NaOl) is used as a reference. The biosurfactants are characterized using surface tension and foam analysis. The interaction of the minerals with the surfactants is characterized using zeta potential, solubility, and single-mineral flotation. The collecting properties of the surfactants are compared for the ultrafine (− 20 μm) and coarser (38–90 μm) particle size in the two-mineral flotation of hematite and malachite against quartz. The ultrafine particle size improves the grade in the oleate flotation of hematite, as well as the grades in the DDM flotation of hematite and malachite, which is explained by the weak interactions of the metal oxides with fatty acids and DDM. At the same time, the flotation with ac-LSL and ac-ASL is highly tolerant to the ultrafine particle size. These results indicate that biosurfactants are an interesting alternative to conventional petroleum-based surfactants in the flotation of Fe and Cu oxides. Moreover, a proper selection of surfactants can help combat the problem of fines.

Feb 23, 2023

By P. Maltais

Over the last 10 years, Computer Aided Design, Finite Elements Analysis and field testing of prototypes have enabled the cycling industry to grow and to significantly improve its products. However, today's cyclists have become more and more demanding, making these classical design approaches almost obsolete. Devinci understood that problem four years ago and fully revisited its design approach; to offer bicycle frames better suited to real life riding, one must fully know those real life conditions. In partnership with the University de Sherbrooke, Quebec, Canada, Devinci then developed a bicycle enabling them to measure the actual load applied on a bicycle frame in real-time for real riding conditions: the instrumented bike. Today, Devinci uses its instrumented road and mountain bikes, combined with virtual prototyping and laboratory testing capabilities to develop better bicycles, faster.

Jan 1, 2006

By R. V. Higgins

"INTRODUCTION When nations throughout the world are pitted against each other in a war in which petroleum plays a major role, scientist and engineers of the petroleum industry must give serious thought to ways and means for recover¬ing greater percentages of oil from natural reservoirs than in the past. Petroleum and its products are vital to highly mechanized modern warfare, and the victorious nations will be those whose armies, navies, and air forces are supplied with adequate fuel oil, gasoline, and lubricants until the war is won.Efficient recovery of oil from underground reservoirs depends on many interrelated techniques; evaluation of the producing performance of wells upon the basis of their productivity indexes is one such tool. Oil wells usually yield oil at a maximum rate when first ""brought in"". The rate of production begins to decline soon after the first oil is delivered to the tanks, and although part of the decline usually can be attributed to natural reduction of reservoir pressure as oil and as are withdrawn from the reservoir, a larger proportion frequently is caused by greater saturation of water and as in the producing formation about wells and clogging of the pores of the sands by silt, organic salt, and insoluble hydrocarbons. If the maximum quantity of oil is to be recovered from reservoir sands and rocks by wells, it is then imperative that the ability of wells to produce oil be watched closely and all adverse influences that affect the case with which oil can flow to wells be corrected if possible."

Sep 1, 1942

By D L. Head

Critical risk management (CRM) has become one of the latest safety buzz terms in mining. Everyone seems to be doing it, everyone seems to know about it, yet we are still having fatalities in our industry from well understood hazards such as mobile equipment amongst others.

May 5, 2022

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Boltsfork 7 1/2-minute quadrangle in eastern Kentucky was selected as the study area. Results indicate that of the original 280.2 M tons of resource in the quadrangle, only 99.8 M tons (35.6%) is recoverable at a mining cost of $25 per ton or less.

Jan 1, 1994

By C Parihar, R Garg, A Bhandari, S Bhandari

Blasting can impact the efficiency of entire downstream mining operation. Individual technology solutions for blasting have been available in the industry for many years but all of them only cater for certain aspects of blasting. Many of them are based on individual research and/or experiences. Some of the available software solutions are not suitable to be used in the field as that they need advanced skills or tools. Also, most do not take technology advancements like mobility, advanced data analytics, web solutions and integration into consideration. Hence, no technology platform is currently present in the industry that addresses all potential needs a blaster may need in an integrated manner.This paper presents an integrated solution that takes care of all aspects of blasting – design blasts according to mine plan; collect data after drilling has been carried out (as there is often difference in designed and actual drilled hole locations in the field); predict blast results in terms of fragmentation, flyrock, ground and air vibrations, wave front reinforcement and flyrock distance; and after assessment, allows changes in charging, delay timing and sequence. The technology solution is a secure, cloud-hosted, web-based software-as-a-service solution that can be accessed from anywhere. Also it has a mobile app, which is available for both Android and iPhone/iPad. The mobile app is also integrated with the web-based solution using application programming interface calls to the central data repository.Case studies for two limestone mines are presented where this solution is being used in its initial format. This software platform enabled analysis of the outcome from a previous blast pattern and then subsequently allowed optimisation of blasting operations based on historical data. Uses of this platform have resulted in improved key performance indicators in these two limestone mines. The mobile app as part of this platform enables extensive field blast data capture and analysis and also various predictions before a blast. Data collected include blast parameters, individual hole charging, initiation pattern, videos, photographs and vibration records for analysis/reporting. The key features of the solution are a blast designer, a detailed blast data collection/analysis and a series of environmental predictors. These predictors give blast results in terms of fragmentation, flyrock, ground and air vibrations and wave front reinforcement and take remedial steps before blasting to optimise and control adverse environmental impact. Many features, such as fragmentation predictor and mobility solution, are completely unique features that are not available elsewhere in such a field personnel-friendly manner.CITATION:Bhandari, S, Parihar, C, Garg, R and Bhandari, A, 2015. An integrated technology solution for optimised and environmentally-controlled blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015