Search Documents

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Extensive testwork on atmospheric thermal magnesium production has highlighted certain important fundamental and operational factors that have a major influence on magnesium extraction and its extraction rate, the condensation efficiency of magnesium, as well as on the quality of the condensed metal. The possible impact of these factors on the selection and preparation of raw materials, recipe choice, furnace electrical energy consumption, and on the refining requirements of the crude magnesium is discussed. Selected pilot plant operational and metallurgical data are also presented.

Jan 1, 2006

By AIME AIME

PERHAPS the most interesting paper of the subsidence session on Monday morning was that by Roland D. Parks entitled "Yieldable Metal Props for Underground Support." This paper described the development of a telescoping prop made from two pieces of pipe. The lower and larger in diameter has cast in it a soft metallic alloy which is slowly extruded through an orifice in the upper and smaller piece of pipe. In this way, the length of the prop decreases gradually as the load from the roof increases. The stress-strain diagram for these props, as tested in the laboratory, is almost ideal, and can be duplicated satisfactorily in successive tests. They have not yet been tested underground. Another paper of much interest was presented by Prof. P. B. Bucky. It is an addition to his series on structural models as applied to mining and was entitled "Effect of Approximately Vertical Cracks in the Behavior of Hori¬zontally Lying Roof Strata." It was illustrated by motion pictures of a model under test. After explaining the un¬derlying theory, the apparatus and the mode of testing, Prof. Bucky set forth the effect of vertical cracks in a mine roof, as follows: (a) the wider the crack, the weaker the roof; (b) where the sides of the crack are in juxtaposition, there is little weakening of the roof; (c) grouting cracks whose sides are not in contact restores the strength of the roof until it may be as strong as, or stronger than the uncracked roof. Small paper props helped sustain the roof. Both the nature of the material and its bonding affect its behavior under stress.

Jan 1, 1933

In many base metal sulphide concentrators reagents such as collector and cyanide are often added to the grinding mill as well as to the flotation circuit. Whilst good reasons can be cited for splitting the reagent addition in this way, the benefits of such are rarely quantified and the complex reagent-mineral-media interactions occurring during milling are often poorly understood in terms of pulp chemistry. A new laboratory batch grinding mill designed by Magotteaux allows the user to measure, monitor, and control the pulp chemical conditions during grinding when testing different ores and media. Some of these parameters include pulp pH, pulp Eh, temperature, gaseous atmosphere, and dissolved oxygen concentration. In a recent development, the mill has been coupled with a simple on-line reagent monitoring system, designed by CSIRO, which allows the levels of species such as xanthate and cyanide in the grinding pulp to also be measured continuously during milling using a robust UV detection system. In this way the uptake of collector during grinding and the rate and ex-tent of cyanide interaction with the minerals and media can be determined as a function of grinding time. A series of grinding tests using an Australian nickel sulphide ore was conducted with the coupled system in which the cyanide dose, xanthate dose, and media type were systematically varied. The xanthate and cyanide levels were monitored as a function of grinding time and the data collected are discussed in terms of the pulp chemistry of the system and implications for plant reagent dosing strategies.

Jan 1, 2014

By Kevin J. Ma, John Stankus, Dakota Faulkner

"Expandable rock bolts are widely used in hard rock mines as an efficient ground control product. However, capacity and service life can be significantly reduced if the metallic body is subjected to corrosion. In some hard rock mines in the U.S., highly corrosive ground conditions exist, and it has been reported that inflatable rock bolts have corroded within a few months after installation. To provide mining industry a cost-effective inflatable bolt and combat the corrosion issues, Jennmar Corporation, Inc., and its subsidiary Keystone Mining Services, LLC (KMS), analyzed corroded bolt samples, identified root causes, evaluated properties of various coating materials, and developed a new inflatable rock bolt, Python M3TM, that is protected with an innovative PyFlexU2TM coating. The new generation Python M3 features improved steel chemistry for reliable performance, modified profile for better inflation, and surface preparation and coating application. The PyFlexU2 is impervious to liquid and air, durable, and UV resistant. With a flexible adhesive, and highly corrosion-resistant undercoating, and a very hard sacrificial surface coating, the PyFlexU2 coating system provides the Python M3 superior protection against chemical corrosion and physical scratch damage. The under-coating has exceptional flexibility and adhesion to prevent coating micro-cracks or fractures after bolt inflation and possesses excellent corrosion resistance to acids (pH <3), alkalis (pH >11), fuels, and salt solvents. The corrosion and scratch resistant PyFlexU2 coating offers very effective bolt protection for extra longevity in highly corrosive environments. The Python M3 coated with PyFlexU2 has been tested in the most challenging conditions, including laboratory corrosion tests in extreme acidic and basic solvents, rock slurry, and borehole scratch insertion tests. With demonstrated corrosion and scratch resistance, the product has been greatly welcomed by hard rock mines in the West and is currently installed in large scale. This paper identifies the root causes of the bolt corrosion, discusses the analysis process, and details laboratory and underground tests carried out on the Python M3 coated with PyFlexU2. The Python M3TM and PyFlexU2TM are subjects covered by pending U.S. Patent Applications assigned to FCI Holdings Delaware, LLC."

Jan 1, 2017

By S. Hopkins, J. Nolan, S. Gillis

"Cast in place concrete shaft linings have been used in many salt and potash shafts sunk in North America over the last 100 years. A large number of these shafts have exceeded their initial design lives and as producers look to extend the life of their operational assets, maintenance costs and shaft downtime will, in many cases, continue to rise unless repair work is undertaken. Successfully implementing concrete liner repair schemes in operating salt and potash shafts is complicated due to their age, environment and time constraints during inspection, detailed design and construction. This paper outlines a general approach to the repair of concrete-lined portions of these shafts, based on lessons learned from the authors’ involvement in a recent repair project. INTRODUCTION Prior to the recent boom in potash mine construction many of North America’s potash mine shafts were entering their sixth continuous decade of production (Table 1). Of North America’s salt mines, one has been in continuous production, for nearly nine decades.As would be expected, considering the environment in which these liners operate and the age of the material, the concrete-lined sections of the shafts outlined in Table 1 have been noted by the authors to have lost both cross-sectional thickness and strength over time. Since construction, three principal factors have contributed to this loss in section/strength; (1) physical degradation (impact, freeze/thaw or rebar expansion), (2) chemical degradation from brine/water inflows (Neville 1969; Bothwell, 1972) and (3) overstressing of the liner. These factors may act in combination, in which case they can produce more significant distress than individually. Physical degradation There are three main causes of physical degradation of concrete shaft liners. The first is impact from falling debris/tools or equipment (whether large or small), which may damage specific sections of concrete lining as they fall through the shaft. Impacts tend to damage infrastructure fixed to the shaft liner more than the liner itself, so damage from this mode of failure is usually localised, for example, where bolts fixing a shaft services bracket to the wall have been pulled away, pulling out the concrete around the bolts with them."

Jan 1, 2019

By A Gibbs

Culture and leadership go hand in hand, especially when it comes to investing in safety. But the reality is that most safety leaders haven’t been taught the fundamental soft skills needed to lead effectively. In fact, only one in four safety leaders demonstrate effective skills and behaviours. Furthermore, when compared to its peers in other high-risk industries, our research indicates mining has the most room for improvement when it comes to effective safety leadership. In this presentation safety culture, climate and leadership will be outlined. Additionally, research data collected from our clients, across a variety of industries, will be shared to inspire reflection on the value of safety leadership. Finally, strategies to empower leaders and increase safety leadership behaviours will be described.

May 5, 2022

By Basilio Giurgola, Jeremiah M. Jezerski, Filippo Azzara, Federico Bonaiuti, Russell H. Lutch

The Northeast Boundary Tunnel Project consists of a 23 ft diameter, 27,000 ft long, CSO tunnel, multiple underground connections, and significant surface works within an urban corridor. The NEBT alignment depths range from 60 to 140 ft and includes seven shafts ranging in depth from 77 to 155 ft with diameters varying from about 19.5 to 56 ft, some as in-line connections and others required adits for connection to the main tunnel. This paper focuses on the design and construction of two major underground connections which are the First Street Connector Tunnel and the Mount Olivet Road Diversion Sewer.

Jun 13, 2023

By W. H. MacLean, S. Liaghat

Abstract- The Key Tuffite is a thick (0.3 m to 6 m) and laterally extensive (-10 km) cherty, sulfide-bearing tuff unit in Archean greenstones in the Matagami mining district in northwestern Quebec. It lies at the contact of the Watson Lake Group and overlying Wabassee Group volcanic rocks, and is host to major Zn-Cu volcanogenic massive sulfide deposits. The tuff component is highly altered and its volcanic precursors are not identifiable by petrographie means. The tuff is mixed with a volcanic exhalative component comprising chert, carbonate and sulfides (pyrite, pyrrhotite, and minor sphalerite and chalcopyrite). The normative mineral composition of the Key Tuffite is 33% quartz, 28% sulfides, 16% sericite, 8% carbonate, 60Jo chlorite and 9% other minerals. In the vicinity of the Bell Allard and Orchan mines, the precursor tuff components are identified using immobile major and trace elements, as Watson Lake tholeiitic rhyolite (Zr/Y = 1.5 to 3.5, LaN/Ybn. = 1.7 to 2.8, Si02 = 72.5 ± 1.2 wt %, and Wabassee calc-alkaline andesite (Zr/Y =9, LaN/Ybn. = 4 to 8, Si02 = 56% to 65%). Immobile element computation techniques were used to calculate mass additions and losses in the conversion of the tuff to the Key Tuffite. Average net amounts of Fep3 (27% total iron), Si02 (14%), CaO (8%), S and K20 ( + 2%), were added, Na2O was removed (-2.8%), and MgO was over-all unchanged. Total net mass change was +63%, which comprises mainly exhalative additions, but also includes changes owing to hydrothermal alteration of the tuff component.

Jan 1, 1992

By B. T., Colley

AS always when metallurgical operations are conducted within or close to agricultural and stock-raising regions, the question of damage due to fume and smoke presented itself when the Cerro de Pasco Copper Corporation&apos;s new smelter commenced to operate in La Oroya in 1922, For more than twenty years the Corporation had operated its old plant close to Cerro de Pasco without encountering difficulties from smoke claims, owing to the fact that it was in an open plain where more or less constant air currents carried and dissipated the smoke over large areas, affording ample dilution. But Oroya is in a deep canyon formed by four contributing valleys up and down which the smoke travels for long distances in a more or less concentrated form. Though the altitude of Oroya is more than 12,000 ft., and the surrounding country rises to much greater elevations, nevertheless there exists there a large and important stock-raising industry and also a considerable development in agriculture, consisting of the cultivation of potatoes, barley, etc.

Jan 1, 1945

By R. T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and-error techniques. This paper introduces a two-dimensional finite element model of briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, the velocity field, the stress distribution, roll force and torque. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquette after its exit from the roll. This enables to perform realistic computer experiments which are helpful for establishing the forming cavity geometry and process conditions necessary to produce briquettes with the desired properties. Three forming cavity profiles are analyzed. Results from model are verified on experimental roller press and best cavity profile is recommended for briquetting of sub bituminous coal fines.

Jan 1, 2014

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casing-heads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By G Hancock, A Kemp, I Taylor

The mine site is situated south east of Port Hedland in the Pilbara region of Western Australia. A detailed engineering design was undertaken for six irregularly shaped waste rock dumps at the site. The design was undertaken to ensure long-term stability of the dumps and optimise material movements for closure construction. The Watershed Erosion Prediction Program (WEPP) and SIBERIA landscape evolution modelling was undertaken for the landforms using regional and site-specific material characteristics to provide an indication of the maximum allowable slopes and corresponding slope lengths for long-term stability.The majority of the waste materials present in the waste rock dumps are considered likely to be subgrade banded iron formation (BIF) and chert, which is generally competent material. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. Geological records also indicate that the dolerite is logged as being heavily kaolinised in the geological logging, hence kaolinite is very likely to be present within the waste dumps on-site. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert).The final design configuration of the largest existing ‘unplanned’ waste rock stockpile is compared to a hypothetical continuous ten degree outer embankment alternative. This paper will present a brief description of the alternatives for closure of three waste dumps in close proximity to each other and how the detailed design based on site-specific materials and conditions compare to an alternative approach blankly assuming that most materials will be erosionally stable at less than ten degrees.CITATION:Kemp, A, Taylor, I?and Hancock,?G,?2014. Landform design for Pilbara mine site – why plan and design waste rock dumps for closure based on site-specific conditions?, in Proceedings Life-of-Mine 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By T. Tholana, P. N. Neingo

"Mining companies globally are currently facing severe economic and financial challenges. In addition to global challenges, the South African mining industry has to face other operational challenges that are unique to the country and which threaten the survival and competitiveness of the industry. Profit margins are being squeezed by rising costs and decreasing commodity prices, while labour productivity is greatly affected by intermittent labour unrest. This paper analyses how the South African gold mining industry has performed pre-, during, and post the global financial crisis of 2008. The competitiveness of the industry in terms of labour productivity and industry cost curve position is analysed for the period 2006–2013 to assess the impacts of both the global financial crisis and labour unrest. An analysis of the South African gold mining industry is presented at company as well as mine level. Productivity measure in this paper is limited to labour productivity, in line with limited reporting on productivity. All the data analysed was obtained from the public domain. IntroductionSouth Africa dominated the world as the number one gold producer until 2009 when China took that position, and today South Africa ranks fifth after China, Australia, Russia, and the USA. According to Statistics South Africa (2009), South Africa still had about 30 years of production in the gold sector, a forecast that fluctuates based on the day’s modifying factors. Although South Africa has a comparative advantage in terms of minerals endowment, there are challenges faced by the mining industry that hinder translation of the comparative advantage into a competitive advantage. The industry continually seeks to address these challenges to remain competitive in global markets while addressing national and community needs.Neingo and Cawood (2014) argued that stakeholders in mining are continually concerned with mine management’s ability to translate use inputs effectively into quality outputs. They further suggested close monitoring of effective utilization of people, materials, and money to obtain maximum production of commodities under given conditions. Productivity is measured in various ways, including unit cost, output per employee, and output per unit capital equipment"

Jan 1, 2016

By R. Letsaole, H. Mabowa, J. Sehat, J. Tshilongo, T. Rampfumedzi, N. Ntsasa, A. Mkhohlakal1

This study explores the use of co-collectors to enhance the recovery and determination of rhodium during fire assay with lead collection, followed by acid dissolution using conventional hot plate methods. Rhodium, a critical platinum group metal, poses analytical challenges due to its low natural abundance and complex chemistry. Among the co-collectors tested, palladium and tellurium demonstrated significantly improved rhodium recoveries, ranging between 100% and 120%, whereas silver resulted in poor recovery and higher error margins. These findings highlight that co-collectors can enhance the efficiency and sensitivity of platinum group metal analysis, although their effectiveness is dependent on the chemical interaction with the target element. Acid dissolution was essential to ensure complete digestion of prills prior to analysis, enabling accurate quantification of rhodium. Overall, the findings suggest that palladium and tellurium are effective co-collectors for rhodium determination in fire assay, while silver and lead flux alone are unsuitable. This work provides important insight into optimising fire assay procedures for reliable rhodium analysis, with potential benefits for platinum group metals recovery and economic evaluation.

Mar 6, 2026

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil. into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casingheads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017

By AIME AIME

ON the morning of Monday, Nov. 9, 1936, two motorcycles, with sirens screeching, - escorted a procession of 70 automobiles from the Colonia Railway Station in Mexico City to the Hotel Geneve. Riding in&apos; the cars were just over 200 visitors- members of the A.I.M.E. and their guests. They had come, via St. Louis, in two special trains from 24 different states for the 146th General Meeting of the Institute. During the morning they and 200 others, who had come from the United States by automobile or from various cities and mining camps in Mexico, duly registered with !efficient Mme. Irma Ordoiiez de Obregon and her assistants. Then started a week of strenuous but delightful activity that will never be forgotten by the participants. They were to cover more than 500 miles by automobile, always with a motor escort, and often

Jan 1, 1937

By Yuting Xue, Mark Van Dyke, Joe Wickline

The understanding of coal mine roof lithology is a critical component in the determination of engineering solutions for roof control. Coreholes were the first technology available to determine lithology of the roof in reserve areas, but coreholes are typically drilled 500–2,500 ft apart due to their cost and sometimes reach more than $125,000 dollars per hole, depending on mine conditions. The next method developed to bridge this gap was the fiber-optic scope which is utilized in the roof at the faces of underground development. High-end fiber-optic scopes can also be costly (20,000–40,000 dollars) but are more affordable than drilling a corehole, and the information can be processed immediately to make quick roof support determinations. The fiberscope can be operated wherever a roof bolter can drill a hole, and there are no restrictions related to property owners, proximity to streams, elevation changes, etc. The latest borescoping method utilized by mining companies is the use of videoscopes. Videoscopes and all borescopes in general are limited by the lengths of the scope and the length of the borehole drilled in the mine. Videoscopes have the advantage of being able to record video while examining the roof lithology. The information can be recorded quickly underground and then be examined on the surface which allows anyone to capture the video so that a geologist can make lithology descriptions without ever going underground. In the past, videoscopes had limited resolution, a short battery life, were fragile and were relatively costly. As technology progresses, videoscopes have become more affordable, have increased battery life, and offer enhanced 1080p resolution. With the broader availability of affordable videoscopes, videoscopes can be more readily used in various mine environments at every active section underground. This paper will discuss the types of videoscopes available, the features that will aid in lithology description/identification, the deployment methods pertaining to supplemental roof support recommendations, and an advanced methodology to enhance accuracy in understanding roof lithology.

Feb 1, 2025

THIS paper is not intended to be a detailed description of the lead, smelting plant at Cockle Creek, as this has been covered in previous papers for the Institute in 1918, Proceedings No. 31, by other members of the staff; but the idea is to give some of the practices and conditions peculiar to these works, also to give some experiments carried out and the conclusions arrived at. Unfortunately, owing to the closing down of the smelting and refinery plant at these works, sone of the experiments could not be carried to a more definite and commercial basis, but they are given in the hope that they may be of interest to members, and may perhaps suggest further thought along the lines indicated.ROASTING AND SINTERINGThe greater part of the ore treated at these works came from the Central mine, Broken Hill, but, in addition, a large quantity was purchased from other parts of New South Wales and from Tasmania. This purchased ore was seldom received in the form of a concentrate, but initially in its crude state, and therefore had to be crushed. The crushing was done in a Krupp mill, and the ore then added to the roasting mixture. This addition of crude ore was one of the main...

Jan 1, 1923