Search Documents

"INTRODUCTION These safety standards for anthracite mines have been prepared for use as a guide for Federal inspectors. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7282 issued in May 1944 and used as a guide in Federal inspections. No provision made in these safety standards should be construed or operate to nullify any existing State statutes; they are intended to supplement the State statutes in the interest of increased mine safety. Mines are inspected in accordance with the Federal Coal-Mine Inspection and Investigation Act of 1941, Public Law 49, 77th Congress, H. R. 2082. Any unusual hazard noted by an inspector and not covered by these standards will be discussed in the inspection report, and suitable remedial procedure will be recommended.ARTICLE I. - SURFACE STRUCTURESSection 1. Breaker and cleaning plant.Electric switches and controls in breakers and cleaning plants should be enclosed.Where coal is dumped at or near air-intake openings, reasonable provisions should be made to prevent the dust from entering the mine.Section 2. Lamp houseNaphtha or other flammable liquids in lamp houses should be kept in approved containers or other suitable dispensers.Flame safety lamps should be permissible and maintained in permissible condition.Flame safety lamps should be properly cleaned, examined, and assembled by a qualified lamp attendant or other competent person before each period of use. Lamp assembly should again be checked by the person using it immediately before he enters the mine.When not in service, methane indicators, flame safety lamps, and electric cap lamps should be in the custody of competent persons responsible for maintenance and testing."

Feb 1, 1948

By J. R. Goode

"The Las Cristinas deposit in Venezuela contains reserves of 12.8 million ounces of gold at a grade of 1.20 g/t (Crystallex, 2004). The deposit comprises fully oxidized saprolite (SAPO) overlying a layer of sulphide-enriched saprolite (SAPS) which lies above carbonateleached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same concentration in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper which has been leached and deposited in the SAPS zone.A previous owner began investigation of the Las Cristinas deposit in 1991. Over the next seven years, the company drilled 1,174 holes with a total length of 159 km, conducted extensive metallurgical testwork, including pilot plant operations, and completed feasibility studies. Construction was started in 1997 and again in 1999, however, on each occasion was suspended.Crystallex has been producing gold inVenezuela since the early 1990s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana (CVG) to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in late 2002 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-inleach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot-scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the testwork conducted in 2003, discusses a 20,000 t/d plant design, and presents economic data."

Jan 1, 2005

By Martin P. O'Connell

"IT IS INDEED A PRIVILEGE to address a group representing a sector of the Canadian economy so important as is the mining sector. Important, not only today, but certainly of great importance for the future development of Canada, for employment, for our trade balance and indeed, when one looks at what we are calling increasingly an industrial strategy, for the future. Surely mining will have a very significant role to play in fulfilling that. It's of special interest to me, as the Minister of Labour - and I ought to confess at the very beginning that I am just two months into this function - of special interest for me to know that you are giving such attention to labour-management relations. I think it is timely that, from my point of view at least, you do this, because for the first time in twenty four years major revisions of the Canada Labour Code as it relates to industrial relations and disputes settlements are currently in the House of Commons going through their second reading, after an easier introduction and some changes which I would be very pleased to describe later this morning. It is very timely too, I think, that we should be looking at this area because public interest is certainly at a high level. It is not only at a high level but it expresses a good deal of irritation with the current status and procedures and results in collective bargaining and there is some urgent search for more sophisticated or modified procedures for settling differences in labour-management relations. The public wants different kinds of results. I think that is apparent to all of us. They want results in terms of justice and equity on both sides. And it means that a Minister of Labour and certainly governments who often are representing, or are the third party in discussions, have a very important and complex role to play in attempting to create a balance as these two parties come to contracts and come to agreements."

Jan 1, 1972

By José Luis Calderón, Percy Arrosquipa

Compañía Minera Poderosa ha identificado una interesante oportunidad de generar valor y de mejorar tanto el clima laboral como el de relaciones comunitarias mediante el proyecto descrito en este artículo. El proyecto se orientó a motivar la incorporación de prácticas de responsabilidad social, tanto entre proveedores de bienes y servicios, como entre empresarios mineros artesanales en proceso de formalización. Como ejemplo, se analiza el caso del cofinanciamiento de la obra “Mejoramiento del sistema de agua para consumo humano del anexo Pueblo Nuevo”, que benefició a 195 familias con un servicio de agua de calidad las 24 horas del día. De este modo, se corrigió una fuente de conflictos sociales y se materializó una alianza para el desarrollo local entre la mediana minería y la minería artesanal. Por su parte, Asociación Pataz entregó certificados de donación, deducibles del Impuesto a la Renta, a los aportantes.

Sep 30, 2017

By R. D. Hossack

"The selection of a site for plant facilities is a function of several factors and has as its objective the maximization of profits, given fixed markets and sources of raw material locations. In practice there are several sites, any one of which or a combination of two or more would be suitable to meet the basic requirements of source of supply of raw material and labour and still fulfill market demands. The model used to select the optimum profit combination utilizes both computer programs and traditional financial analysis techniques. Of the three computer programs used in the mode), one is a linear program and another is a transportation simulator. Basic cost and price data are required. In examining costs, three levels are used: (a) distribution costs of raw material to the plant and finished goods to the market; (b) direct production costs at the plant, such as labour and locally supplied material; and (c) capital and overhead costs at the plant, such as construction costs, taxes, insurance, and federal and provincial cost allowances. The direct costs generally depend on the scale of operations, so that a large plant in one location may have a lower unit cost than two smaller plants. This, of course, must be balanced against distribution costs. In examining profit, it is necessary to think in terms of the price and volume of sales at each of the market locations. Given basic data and relationships, the model can be used to optimally locate production facilities or, alter-natively, optimally structure a transportation network given existing locations of plants and markets. It is dynamic to the extent that it can react to changes in volume, price and cost to optimally locate an additional plant, the expansion of existing plants, the shutting down or cutting back of plants, or the restructuring of distribution networks."

Jan 1, 1970

Rather like the mythical "Economic Man" "an employer" in this context must necessarily be an abstraction, and the views possessed by such an abstraction, a composite of many views known to have been expressed. Not even the complex Conciliation and Arbitration legislation in this country provides any helpful specifications, except in one peculiar particular. The Australian Conciliation and Arbitration Act provides an almost totally tautological definition, except in that one oddity referred to above. It is this : "An employer means any employer in any industry, and includes any person who is usually an employer in an industry, and also includes a Club." No doubt there is some perfectly justifiable reason for such specific and unique particularity in an otherwise meaning- less definition. That need not trouble us in this exercise.

Jan 1, 1982

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By Roman Y. Poderny, Vladimir V. Rjevskii

In the USSR, the Moscow Institute of Radio Electronics tronics and Mining Electro-Mechanics (MIRGEM) has started what it hopes will become a nationwide movement to educate mining students in the precise specialties that industry has come to require. Courses for mining engineers, the MIRGEM faculty proposes, should dovetail as exactly as possible with specific jobs available in the mining profession. Acting upon this thesis, MIRGEM revised its own curriculum in 1962 and has since presented an over-all plan for Soviet mining education before two mining school conferences as well as the Ministry of Higher Education and a number of major Soviet industrial ministries. The plan was universally approved with some suggested revisions. SOVIET MINING EDUCATION TODAY At present, mining education in the Soviet Union covers the exploitation of solid minerals and raw materials, including coal as well as ferrous and nonferrous metals. The extraction, storage, and refining of oil and gas is treated as a separate discipline. In all, there are 33 Soviet universities and institutes that train mining engineers for careers in the industrial, research and educational fields.

Jan 9, 1966

By Steve Jones

Minor subsidence damage to the Burgettstown Junior-Senior High School building and grounds near Burgettstown, Washington County, Pennsylvania, prompted an investigation of the site in early 1985 by the Bureau of Abandoned Mine Reclamation of the Pennsylvania Department of Environmental Resources. The investigation determined that subsidence over an abandoned coal mine was occurring and that additional damaging subsidence would occur if reclamation measures were not taken. A Pittsburgh Coal Seam Mine which was abandoned in the 1920's underlies the school at a depth of sixty-five (65) feet. This sixty-five foot section is comprised of five (5) feet of unconsolidated overburden and sixty (60) feet of thinly bedded, highly fractured shale. Approximately five and one-half (5-1/2) feet of Pittsburgh Coal was extracted at the school site. A thin shale binder and one (1) to one and one-half (1-1/2) feet of roof coal were left in place. Within the Contractor's Underground Working Area (See Figure 1) approximately thirty (30) percent of the coal was extracted. It appears that the mine was just being developed in the vicinity of the school when it was abandoned for no known reason. Other nearby portions of the mine show extraction approaching sixty-five (65) percent.

Jan 1, 1986

By Frederick McNeill, John Harper, Mahmood Khwaja, Shawn Lavoie, Timothy Cloughert, David Polcari

City of Manchester, NH, is implementing a 20-year plan to control and significantly reduce overflow of its sewer system. The long-term control plan had called for large scale box culvert installation through downtown Manchester. The City and the project team evaluated, and eventually selected, tunneling as an alternative to mitigate construction related impacts for open trench approach. This paper provides an overview of the alternative evaluation process; discusses the development of the preliminary design for the 12,000 feet long, 12-ft internal diameter tunnel, including plan and profile selection, subsurface conditions, drop shafts and the anticipated packaging of the separation areas.

Dec 1, 2022

By Lynn Crayne

We used Glyoxal as the hardener, at a final concentration of 10% by volume and therefore 20% by volume in the A-Component. They worked pretty well what we did was we shaved the joints on each of the pipes when we assembled them so they wouldn't rip the packers and then we greased the packers very well going in. We had to replace some but we have any getting stuck or didn't lose any pipes.

Feb 10, 2003

By Jerry D. St. Clair

A multidisciplinary team of scientists and engineers at Wont has been working to understand heavy metal contamination of DuPont process waste streams and technologies for abatement of these metals. As part of this effort, an extensive study was made of a specific waste stream of importance in DuPont's environmental commitment. This 200 gpm stream contains 5-5000 ppm of nickel plus a variety of inorganic and organic constituents. The chemical complexity of the waste rendered conventional. alkaline precipitation ineffective, and only through the simultaneous application of analytical characterization, fundamental chemical understanding, and process engineering did effective technical approaches emerge. In this instance, ion exchange, sulfide precipitation, and caustic digestion ultimately proved successful in reducing the nickel to below the 1 ppm target. The results of this study will be presented, along with key learnings about the process of solving heavy metal contamination problems.

Jan 1, 1994

By Jochen Wans

BCT® - Belt Casting Technology is the new horizontal near-net-shape casting process to produce flat steel products. BCT is the revolutionary leap in casting technology, designed for the production of special and conventional steel grades. Within a partnership between Salzgitter Flachstahl GmbH and SMS Siemag AG, the worldwide first caster is now in operation. SMS Siemag AG (in cooperation with Salzgitter Flachstahl GmbH) has erected the first industrial-scale casting machine located at Peine steelworks. The lecture will start with an overview about the highlights of the BCT® process with regard to the mechanical engineering aspects, while the second part will present current commissioning results and operation experiences. Since December 2012, the BCT plant is running. Up to March 2015 more than 90 casts have been carried out, 26 with FeMn-alloys. Never before flat steel was casted in dimensions of 1000 mm * 15 mm and with casting speeds more than 14 m/min.

Aug 16, 2017

By Ralph H. Cleland

Introduction The mines of northern Ontario have entered the class of deep mines. It has often been asked: How deep can operations be carried on? What will the temperature be? This paper is a résumé of a brief survey of rock temperatures made by the Ontario Department of Mines during the year 1932. Present temperatures were recorded and the geothermal gradients that now exist were determined. No alarming situations were found, but many interesting ones have been noted. Northern Ontario mines are fortunately situated as compared with most deep-level mines of the world. The mean yearly temperature, as determined from meteorological records of the Federal Department of Marine, is from 33 to 38 degrees Fahrenheit. The tables on the next page show the temperature range in and about our mining camps ( l ). As no exact figures were obtainable for Kirkland Lake, the data for Iroquois Falls, which is about 50 miles northwest, were taken as applicable there. The figures for Timmins were checked against those of Cochrane and Iroquois Falls and found to be very similar, so that the Cochrane data may be used for the Porcupine camp. The yearly mean temperature is considered to be 33.5 F.

Jan 1, 1933

By R. August Heindl

A process for recovering manganese from open-hearth steel-plant slags was investigated. The proposed method of accomplishing this is indicated by the flow diagram in figure 1. Mixtures of open-hearth, steel-plant flush slags and limestone, so proportioned as to have molar [CaO -3P205] ratios of approximately 2, were fired at approximately 2,400° F. in an oxidizing atmosphere and then cooled slowly. This treatment produced a clinker consisting principally of two solid phases comprised of (1) various combinations of the oxides of manganese, iron, aluminum, and magnesium, probably in spinel complexes, and (2) a dicalcium silicate phase, which contains the phosphorus. Reduction of these clinkers with hydrogen or with gaseous mixtures containing CO, CH4, and other hydrocarbons at about 1,300° F. formed manganous oxide as well as varying amounts of ferrous oxide and iron. Carbon monoxide and mixtures of hydrogen and carbon monoxide effectively reduced the clinkers but also gave higher proportions of soluble iron when the manganese was extracted from the reduced clinkers by leaching at about 80° F. with ammonium carbonate solutions containing 26 to 28 percent ammonia and 15 to 26 percent carbon dioxide. It is believed that the manganese is in solution as an ammonia-manganese complex. Concentrations of about 90 grams of manganese per liter were obtained by batch countercurrent procedures. By distilling 50 percent of the ammonia, the ammonia-manganese complex was decomposed, and approximately 90 percent of the manganese was precipitated as the carbonate with the simultaneous precipitation of 15 to 30 percent of the iron, the larger amounts of iron precipitating in the continuous tests. The manganese-iron ratio in the product could be increased either by recycling more manganese from the distillation to the extraction or by aerating the liquor to purge it of iron before, rather than after, the distillation step. Calcination of the pelletized manganese carbonate in an oxidizing stmosphere at 2,000° F. or above gave a final product, Mn304, resistant to crushing and apparently possessing the other physical properties essential in a ferromanganese blast-furnace feed.

Jan 1, 1955

By K. R. Nichol

The author points out that corrosion works 24 hours a day, every day. It is an economic reality that the cost of corrosion is inevitable and that its cost should be incurred in the least expensive way. An economic evaluation technique to properly assess its relative impact is the Discounted Cash Flow Method. Various remedial and corrosion control measures are available and these, when coupled with a planned corrosion control program, help reduce the cost of corrosion.

Jan 1, 1973

By B. K. Shibler

A highly flexible laboratory-scale fluidized-bed reactor was designed, constructed, and successfully operated continuously at temperatures up to 1,300° C during an investigation of thermal methods for decomposing gypsum. This report discusses briefly the many problems encountered in developing the 10-inch-diameter reactor and describes its design and construction in sufficient detail to enable other research organizations to build a comparable unit. The reactor consists of a 10-inch-inside-diameter vertical tube which can be varied from 6 to 10 feet high; it is formed from 2-and 3-foot sections of silicon carbide pipe. The tube is surrounded by a 3-inch heating space formed by an outer 4.5-inch-thick circular wall of insulating firebrick. A cone-shaped fluidizing chamber is bolted to the bottom of the reactor. Fluidizing gas enters through the bottom of the cone, and ore is introduced by means of a screw feeder connected to an inlet located just above the gas port. A silicon carbide overflow tube of 1.25-inch inside diameter extends upward into the reactor. The depth of the bed is controlled by substituting different lengths of overflow tube. Twin dust-recovery systems, each composed of a cyclone and Fiberglas filter, are attached to two gas outlets at the top of the reactor tube. The reactor is designed for research on both exothermic and highly endothermic reactions. It can be fired externally by means of four natural gas burners that jet tangentially into the annular space at the base of the reactor. Alternatively, it can be fired internally, using a mixture of air or oxygen and natural gas as the fluidizing medium. A separate instrument panel contains flowmeters, manometers, an automatic program controller, and a multiple-point recorder for printing a record of the temperatures measured by thermocouples located at critical points in the reactor.

Jan 1, 1963

By P J. Hawke

Within the Mesa J pisolitic iron ore mine, clay is distributed unevenly throughout the deposit and often forms as pods and channels less than 10 m in width. The mine resource model, based on 50 m + 50 m spaced drilling, has been unable to accurately delineate the clay for scheduling and mining purposes. Therefore, alternative methods for mapping the clay-contaminated ore were sought. Predictive clay mapping will significantly reduce production costs at Mesa J through improved selective mining practices, more accurate scheduling, reduced wear on mining equipment and minimising the need for maintenance of haul roads and ramps. High lateral resolution electromagnetic (EM) surveying using a Geonics EM31 instrument can quickly and inexpensively delineate the extent and orientation of the clays. Preliminary results indicate that a block model based on the interpretation of the EM data can accurately predict the distribution, volume and tonnage of ore and waste material. While rip-line mapping, infill drilling, ground penetrating radar and gravity can delineate clay with various degrees of success, none were as efficient as EM31.

Jan 1, 2002

By M. Jayaraman

With the ever increasing demand for commodities, due to changes in lifestyle and increase in population, people are striving to find ways to keep up. Mining is one essential element in the solution. Though being a powerful boost to a country?s economy, mining can have disastrous effects in the absence of waste management practice and technologies; because of the harmful heavy metals and toxic chemical waste that is generated as a by-product in mining operations. It is an established and documented fact that pollution is a major concern for communities having to live with it. Disproportionate water consumption significantly impacts local rivers and ponds thereby reducing freshwater availability and have given rise to social conflict. In light of these misgivings, management and treatment of mine water and waste has gained considerable attention recently. In this paper, we summarize some of the treatment methods that can be adopted by mining companies to reduce their environmental footprint. Appropriate treatment solutions depend on various factors including available space and capital cost for treatment solutions, type of mining waste generated, current state of the mining plant, geographical location, and other location specific issues. Incorporating waste and water management solutions as a priority within mining operations is critical for addressing increasing regulatory requirements and a starting point for initiating other Corporate Social Responsibility (CSR) programs. Collaboration among mining companies, NGOs, local community, and government facilitates successful projects which build trust leading to long term relationships. In this paper we also talk about the benefits of implementing a CSR project that captures the focus of local communities and allows the mining company to focus on operations. Implementing a sustainable business model that incorporates the broader community impacted by projects will continue to benefit even after the mining company ceases operation in that location. The challenges involved with implementing effective CSR projects, which require measuring and reporting effectiveness to create a positive social, economic, and environmental impact is also presented in this paper.

Aug 1, 2013

By S. Borner Schweizer

An overview over SAM’s approach to assess corporate sustainability performance illustrates how sustainability challenges are linked to trends, assessment criteria and finally company performance. This process is exemplified with some general and industry specific criteria. Lastly, results of the Dow Jones Sustainability Assessment 2004 show a considerable gap between leading and average companies. Best practice examples demonstrate how lagging companies could improve their sustainability performance.

Jan 1, 2005