Search Documents

By Dipl. -Ing. Mertens

Gentlemen: I am pleased and regard it as a priviledge to give you a report on rapid roadheading with heading machines in the coal mining industry of Western Germany. Importance of Heading Operations in the West German Coal Mining Industry Every year about 770 km of headings are driven In the seams of the West German coal mines, most of them gate roads, the rest rise headings, to open new faces. In thick seams the heading operations are carried out entirely in the coal, in thin seams the country rock has to be ripped. The total length of 770 km corresponds to a rock volume of roughly 9.5 million m3; this figure underlines the importance of the heading operations in the coal mining industry of our country.

Jan 1, 1970

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By G. L. Hopps

Various chemicals, including compounds of copper and lead, were added to a mixture of No. 2 and No. 6 fuel oils that was fired in an experimental furnace. Tests were made to determine (1) the effectiveness of these chemicals in removing soot deposits on probes devised to simulate heat-transfer surfaces in boilers and (2) the effectiveness of the chemicals in preventing the deposition of soot on the probe surface. Test conditions were regulated so that the temperature of the products of combustion adjacent to the probes was in the range of 625° to 700° F. The clean-metal temperatures of the air-cooled probes were comparable with the water-tube temperatures in boilers operated at 40 to 100 p.s,i.g. The dosages of the fuel oil additives used in these tests were generally larger than those usually recommended for most proprietary compounds.

Jan 1, 1962

By Rhual L. Guerguerian

MINING has been practised by mankind for over sixty centuries (1). In 1876, the "ball mill" was patented, and during the century that followed rotary grinding developed to the state where individual machines are treating tens of thousands of tons of ore per day. This paper gives a brief description of design practices prior to the availability of advanced facilities, followed by modern analytical design development at Dominion over the past ten years.

Jan 1, 1978

By Yves Gratton

The International Commission on Large Dams (ICOLD) is a non-governmental International Organization which provides a forum for the exchange of knowledge and experience in dam engineering. It is the world's leading professional organization dedicated to advancing the technology of dam engineering and supporting socially and environmentally responsible development and management of the world's water resources. ICOLD was founded in 1928 and has National Committees in 82 countries with approximately 7,000 individual members who are engineers, geologists and scientists from governmental and private organizations, consulting firms universities, laboratories and construction companies. Its original aim was to encourage progession in planning, design, construction, operation and maintenance of large dams and associated civil works by collecting and disseminating relevant information and by studying related technical questions. Since the late sixties, focus was put on subjects of current concern such as dam safety, monitoring of performance, reanalysis of older dams and spillways, effects of ageing and environmental impacts. More recently, additional subjects have included cost studies at the planning and construction stages, harnessing international rivers, information for the public at large, and financing.

May 1, 2002

By J. R. Gaw

Recent events pertaining to U. S. energy needs and development of alternative energy fuel resources have made the American public more aware of past and present coal mining operations, and their impacts on the nation's economy and environment. This awareness has developed rapidly due to increased government involvement and consequent media coverage. This is true particularly in the Western states and in Texas. One of the consequences of this increased public awareness is public concern over the perceived and real consequences of mining operations. Emphasis has been placed on potential releases of toxic and hazardous substances, and possible carcinogens. The result of this public concern is a mounting effort at both state and Federal levels to promote stricter laws regulating the mining industry.

Jan 1, 1992

By M. Nowak

Extreme high grades often exert too much influence on surrounding block estimates, leading to a smearing of high grades that can cause overestimation of mineral resources. This concern underlies the decision to cap high grades, i.e., to lower the highest grades in a drill hole data set to some level deemed to be reasonable for producing reliable resource estimates. The choice of a capping level can, by itself, have a large influence on the analysis of the economic viability of a project. Despite this, it is often a choice that is made arbitrarily, guided more by art and tradition than by sound technical analysis. This paper makes suggestions for good capping practices, using methods and procedures that have been presented elsewhere, in the technical literature and in conference papers. The authors propose to use capping only if absolutely necessary, and review examples of cases where capping may not be necessary, or where capping does not make the estimates more reliable. It addresses two particular instances where capping is recommended: (1) where there is good reason to believe that estimation with uncapped grades will overstate the true underlying average grade, and (2) where there is potential for overly optimistic assessments of local block grades in the vicinity of some very high grade assays. The proposed capping practice is based on adjustments to only a very few high grade assays. The level of this capping can be assessed by bootstrapping and through analysis of the effect of extreme values on summary statistics like the average and the coefficient of variation. The paper recommends that good practice include an examination of the potential for local overestimation in higher grade areas.

Aug 1, 2013

By Malte J. M. Gurgel, Axel Preusse

The planning, construction, and monitoring of underground storage facilities is a key factor in meeting upcoming challenges as part of the energy transition from fossil fuels to renewables. Therefore, the many years of knowledge and expertise in ground control gained from coal mining are highly valuable for new mining and storage operations. For such applications, our previous work examined cavity registration, combining structure from motion and LiDAR through a case study in a former lead ore mine. Building on this, the results of this recent case study are discussed regarding the possible application in sites for nuclear waste disposal in Germany including a view on the situation in the United States. Photogrammetric methods are particularly suitable as part of long-term monitoring, which relies on both precise survey results and a large variety of detailed visualization. In order to gain a better understanding of the resulting application potential for holistic monitoring, both existing repositories sites in Germany and ones yet to be found are examined. This search and selection process for high-level nuclear waste disposal is studied in detail together with rules resulting from the (German) mining law, regulations, and other guidelines. Hereby, key requirements of photogrammetric products like oriented images, point clouds, and three-dimensional (3- D) models are identified for different case studies. The findings on accuracy and integrity of the generated models are not only of interest for future repository sites or underground pumped storage power plants, but also offers various possibilities for underground mining of coal and other commodities.

Jul 1, 2023

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By A. B. Hooker

Since man first mined underground, there has been need for adequate illumination; this need has never been fully supplied. At first, suitable lamps were not available. Gradually they have been developed, but along with that development the need for better and better lamps has continued owing to the following conditions and factors: 1. Increasing hazards from gas and dust ignitions. 2. The speeding of operations with mechanized mining, which necessitates greater visibility. 3. A demand that cleaner coal be loaded, which requires higher levels of illumination. 4. The cost of compensation for injuries that has created a demand for better illumination and safer lamps. Use of better lamps has been retarded by: 1. Prejudice and resistance to change on the part of the workers in some districts. 2. The cost and upkeep of the lamps. 3. The present types of lamps, while a great improvement over the old lamps, do not entirely fulfill the requirements for a safe and efficient light for underground workers.

Jan 1, 1938

By S. Rajan

Familiarity with NEMA standards and the influence of the power supply on the motor-load system permits the user to make the necessary decision as to whether a standard or special motor is needed for his particular application. This paper highlights the more important aspects of NEMA standards for ac induction motors from the application engineer's standpoint and the effect of the power supply on motor characteristics.

Jan 1, 1975

The Direct and Indirect Effects of the Reagent Suite on Froth Stability in Laboratory Scale Batch Flotation Tests

Sep 13, 2010

By Young C. Kim

Because of the tremendous technological advances achieved in recent years in microcomputers, it is not only technically feasible but also economically viable to develop an automatic truck dispatching system using a microcomputer. Such an effort was initiated by the Department of mining and Geological Engineering, University of Arizona in the summer of 1983. Up to date results and experiences prove that today's microcomputers can be economically employed for such a system to be used at small to medium scale open-pit mines. An IBM/XT microcomputer with 10 MB harddisk storage, together with automatic sensing capability of truck movements at several key locations in the pit, formed the core of this system. System software is written primarily in MICROSOFT FORTRAN with supporting subroutines in MACRO assembly language. The software is designed to automatically monitor truck movement throughout the pit, to make heuristic assignments based on expected shovel availability and truck travel times, and to record production statistics. It is currently dimensioned to handle 50 trucks, 10 shovels, 10 dump sites and 3 material types. Due to the lack of funds to purchase the necessary communications hardware, the work related to the automatic sensing of truck movements has not been performed to date. Otherwise, the automatic truck dispatching-system is fully operational on a realtime mode.

Jan 1, 1984

By Graham A. Davis, Michael Samis

The dramatic fluctuation in metal and energy prices in the last few years is causing mining companies to consider alternative analytical methods for mine design and valuation. The goal is to improve insight into unforeseen changes in the economic and project environment and to design projects that take advantage of management's ability to respond to these changes. Such flexibly managed projects will contain value that cannot be measured using traditional engineering economic approaches, further motivating the used of alternative, modern valuation methods. This paper considers the valuation of an uneconomic low-grade resource at an open pit gold mine using two of the most popular modern valuation methods, Dynamic Discounted Cash Flow and Real Options. Our analysis demonstrates that the conventional valuation method may incorrectly represent the value and risk attached to mining this type of resource because it is unable to recognize management's ability to respond to future events in a manner that minimizes losses and exploits advantageous business conditions. The results of this paper highlight the importance of recognizing flexibility and business uncertainty in both mine design and valuation.

Jan 1, 2003

Upgrading of a Flow Sheet Selection PC Algorithm for Refractory Concentrates Treatment

Sep 13, 2010

By James O'Brien, Lyman Frost, Grant Hawkes, S. Elangovan, Manohar Sohal, J. S. Herring, Joseph Hartvigsen, Carl Stoots

"Pressing environmental and energy security concerns have brought much needed attention to economic production of hydrogen as the secondary energy carrier for non-electrical markets as well as to meet increasing demand for crude upgrading and desulfurization. While steam reforming of natural gas is currently the dominant method of hydrogen production, it is depleting a valuable fossil fuel while emitting green house gases. Thus, in the long run, efficient, environmentally friendly, and economic means of hydrogen production using nuclear and renewable energy needs to be developed. High temperature electrolysis using solid oxide electrolyte cells is an exceptionally efficient means of generation of high purity hydrogen. It is also capable of directly converting steam and CO2 into synthesis gas. This co-electrolysis process enables conversion of CO2 recovered from concentrated industrial sources into a feedstock for synthetic fuels production. Use of CO2 provides a means of storing hydrogen in a concentrated and convenient form – a hydrocarbon. This is also an effective storage medium for intermittent renewable energy sources such as wind and solar.Ceramatec, Inc and the Idaho National Laboratory are applying solid oxide fuel cell technology to the production of synthesis gas by high temperature co-electrolysis of steam and carbon dioxide. This technology utilizes solid oxide fuel cell stacks to electrochemically remove oxygen from steam and CO2, leaving a clean stream of hydrogen and carbon monoxide suitable for fuel synthesis. By varying the relative concentrations of carbon dioxide and steam, the hydrogen to carbon monoxide product ratio can be controlled as required by the desired type of synthetic fuel being produced from the syngas. The resultant synthesis gas has been used as the feedstock to produce synthetic methane and Fischer Tropsch liquid fuels.Alkaline and proton exchange membrane electrolysis cells typically operate below 100°C, while solid oxide electrolysis cells operates in the 750-850°C range. This higher temperature improves the efficiency significantly. Practically, it translates into a lower cell operating voltage, 1.1-1.4V for high temperature electrolysis vs. ~1.8V for water electrolysis. Hydrogen production is stoichiometric with current in all types of electrolyzers.Carbon dioxide is a valuable resource as a feedstock for energy storage as a hydrocarbon. There is a vast amount of renewable energy that cannot be effectively utilized as grid electricity, but which could be used to convert CO2 to hydrocarbons, offering a solution to the even more difficult (than supplying grid power) challenge of production of sustainable, domestic transportation fuels. Conventional electrolysis and chemical processes could be deployed to accomplish this conversion. However, high temperature co-electrolysis of CO2 and steam to produce synthesis gas using solid oxide fuel cell technology has the potential of improving the efficiency by nearly 50%. A domestic synfuel industry will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles while increasing our energy security."

Jan 1, 2010

In any earth-moving operation, more profit may be earned or lost by equipment scheduling than by any other single facet of the project. Many now-defunct earth movers would have survived the cost-profit squeeze had they followed an efficient, cost saving, equipment scheduling program. The ideal program would have every item of the equipment fleet working all of the time. In practice this ideal situation is not possible. Several basic methods of equipment scheduling, with an infinite number of minor variations, are used. The first approach is the use of a "minimum equipment fleet," of which all items or equipment are scheduled each working shift.

Jan 10, 1967

By J. C. Franklin

The Bureau of Mines substantially reduced shale degradation in a coal mine by two spray coat applications of a water-base epoxy sealant. More than 12,700 square feet of passageways were treated, and in 18 months only one failure occurred. This failure was due to improper spray application, Material costs averaged 13 cents per square foot, and labor costs were 7 cents per square foot. Labor included moving all materials into the mine, the setup time for each of the areas coated, and application of coatings.

Jan 1, 1977

By Deniz Akbay

The strength of rocks and soil is a crucial design parameter in engineering projects, and it can be determined through various test methods such as uniaxial compressive strength, tensile strength, and shear strength. The point load index test is a popular indirect test method for predicting the uniaxial compressive strength of rocks. However, the reliability of the point load index’s estimation of uniaxial compressive strength of rocks is questioned due to the wide range of coefficients that are used to predict uniaxial compressive strength of rocks using point load index values. Factors such as the shape and type of rock specimen, practitioner, and test apparatus used can affect the accuracy of the point load index test. This study investigated the effect of four different specimen shapes used in point load index test (diametral, axial, block, and irregular lump tests) in predicting the uniaxial compressive strength. The rock samples were tested using four test procedures which are called diametral, axial, block, and irregular lump tests. The results showed that the irregular lump test was the most accurate in predicting uniaxial compressive strength, with the highest correlation coefficients and lowest mean absolute percentage errors. The point load index test can be used as a reliable predictor of uniaxial compressive strength of rocks when the irregular lump test is preferred.

Oct 18, 2023