Search Documents

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By L. Yan, B. Lambie, J. Srednicki, J. Carr

Electromagnetic emissions from electrical devices may interfere with electronic safety systems or other devices in the mining environment. This electromagnetic interference (EMI) may cause unwanted changes in the performance of the affected devices and may cause safety issues for miners. To minimize the risk of EMI, the National Institute for Occupational Safety and Health (NIOSH) has conducted research quantifying the electromagnetic emissions of several types of equipment that might be used in the mining environment. Previous research has shown that welding arcs can give off ultraviolet (UV) emissions, visible light, and infrared (IR) emissions that can cause health problem on skin and eyes. In this study, the electromagnetic emissions of the shielded metal arc welding (SMAW) process were monitored and measured. Several factors including operating mode (AC, DC positive or DC+, DC negative or DC-), current setting (low, medium, high, maximum), and electrode type were investigated to compare their effect on emission level. The test shows that the emission level from the welding process can be affected by those factors. The test data also shows that, among those factors, the operating mode has more influence on emission level than do current setting and electrode type. The information in this paper can be useful for the mining industry to better understand the emission in the 9-kHz to 500-MHz frequency range from a SMAW welder.

Feb 1, 2023

By L. Newman, R. Wyrick, R. Berezowsky

The Stillwater Mining Company operates an integrated mines, mill, smelter and base metals refinery complex in Montana, USA for the production of a high-grade platinum group metals (PGM) bearing concentrate, nickel sulphate crystal and cathode copper from the PGM-containing nickel-copper converter matte. The complex was constructed in stages over several years, starting with the mine and the mill, followed by the smelter and finally, a base metals refinery, which was commissioned in 1996. Due to the relatively small quantity of matte production, a straightforward refinery process was initially selected to extract the base metals, which reported to a mixed nickel-copper solution for further treatment off-site, and yielded a high-grade PGM concentrate suitable for treatment in a PGM refinery elsewhere. Subsequently, as a result of increased matte production, the process was modified to separate the nickel and copper, and to produce a nickel sulphate salt and cathode copper. This paper describes the design and operation of the original and the modified processes utilized in the base metals refinery (BMR).

Jan 1, 2004

By T. C. Phalen

"Necessary Qualities There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, also, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the ele¬ments, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of ad-hearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco."

Dec 1, 1919

This paper deals chiefly with the preliminary examination, when a decision has to be made as to whether a prospect has a chance of developing into a mine or not. At this stage it is important to have a fairly clear conception of what is expected of the prospect, andjust what type of mine is sought. Much money can be wasted testing a prospect suitable for a prospector or small syndicate, but which never looked like becoming a mine of sufficient size to interest a company. When undertaking an inspection, therefore, it is necessary to have a broad outline, at least, of the policy of the principals for whom the report is intended.At this early stage it is frequently necessary to form an opinion of the prospects of a property on very meagre data. When new to this type of work one's first reaction is often th~t it is impossible to pass an opinion on the data available. It. is absolutely necessary,however, that an opinion of the possibilities and chances of favourable development be given; The report should strive to convey this information, making quite ::lear the risk involved, how complete are the data on which this opinion is based, and the possible magnitude of the prize. A Preliminary report has to state whether a property has sufficient prospects to warrant testing.The following procedure is suggested in order to make best use of the data and minimise hasty conclusions influenced by preconceived ideas-an ever-present danger.Examination.The first stage is the examination. This should aim at collecting all available significant data, but avoid clouding the issue with detail which, at this stage, will not affect the decision. The following points are considered to be the main ones for which to look:-Geological Environment.As good a working knowledge as possible'of the geology of the area should be obtained. Government Geological Survey reports and maps, if available, will be a big help. A detailed knowledge of the regional geology is not necessary a,t this stage, but a broad outline of the geological setting of the prospect under review, and also of any other important mines in the district, is often helpful in the final decision.The Nature of the Ore-Body.Any facts concerning the nature or occurrence of the lode should be noted as, coupled with experience of similar bodies, they affect the ultimate decision.Structural Control.This is probably the most important factor, in the light of present geological knowledge. Its chief importance is due to two facts:-(a) Structure plays one of the prime parts in ore deposition.(b) Geological knowledge, of structure is somewhat in advance of knowledge of other factors influencing ore deposition.

Jan 1, 1950

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By Guomin Jiang

Potassium ferrate is an excellent multifunctional reagent for wastewater treatment, but its preparation is crucial. The improved hypochlorite oxidation method was used to prepare potassium ferrate in this study. Iron nitrate, the preferred iron source, was added into hypochlorite solution and then the stabilization agent was added during the purification process of product. The influence of available chlorine content, iron molecular proportion, reaction temperature and reaction time on potassium ferrate preparation was investigated. The optimal condition for potassium ferrate preparation is 15% of available chlorine content , 0.6 of iron molecular proportion , 30i of reaction temperature , 45min of reaction time. The yield of potassium ferrate is about 67% with high purity (> 99%). The structure and performances of the product was characterized by XRD, EDX, SEM, TG and IR and the results show that the prepared product is consistent with the properties of potassium ferrate(VI).

Jan 1, 2010

By Aly M. Mohammad

State and federal agencies during rehabilitation of existing bridges may require the existing bridges to be evaluated under seismic conditions. If the bridge does not perform under the seismic event, the bridge may require seismic retrofitting. Bridges are classified as: Critical, Essential, and Others according to their importance. Geotechnical considerations play a major role in evaluating the bridge behavior under a seismic event. Subsurface conditions influence the magnitude of ground acceleration and hence the forces and moments on the superstructure. This paper will provide a detailed description of the geotechnical aspects associated with the seismic retrofit evaluation for the 12th Street and 14th Street Viaducts located in Jersey City, New Jersey. The paper will also present a description of the geotechnical investigation program including seismic cross-hole surveys to determine the dynamic soil parameters, including the results of site-specific response spectra for both the 475 and 2475-year events. Liquefaction assessment methodology utilizing an equivalent factor of safety will also be described and the design method used will be summarized. In general, the pile foundation is modeled as 6x6 foundation stiffness matrix with 36 stiffness coefficients at the center of the pile cap. The seismic loading on the foundation is evaluated in a pseudo-static analysis, where the dynamic earthquake-induced loads are presented by static forces and moments. The computer program FB Pier was used to evaluate the foundation stiffness. The moments, axial loads, and shear are input into the FB Pier model. The stiffness of the foundation is determined and the results are then input into the Structural model to determine new forces and displacements. Adjustments are made until the loads are compatible with the stiffness used. The understanding of the geotechnical conditions at the 12th Street and 14th Street Viaducts and the coordination between the Bridge and Geotechnical Engineers were able to provide significant cost saving to the Owner. The Design Engineers were able to retrofit the existing Viaduct foundations with reasonable number of additional piles. It is believed that the results and finding presented in this paper will benefit both the Bridge Engineers and Geotechnical Engineers by highlighting the importance of interaction between the two disciplines.

Jan 1, 2006

By G. L. Oldright

THE economic manufacture of sulfuric acid by the ordinary chamber process usually involves production on a large scale and a plant that is costly to construct. The nature of sulfuric acid makes it costly to transport any great distance. For these reasons, the metallurgist has not found it feasible, at times, to beneficiate ores amenable to leaching, and a. need exists for a local process that will produce acid cheaply on a small or large scale. To leach ores containing residual sulfides, an oxidizer, such as ferric sulfate, is needed in solution. Precipitation with scrap iron is one of the cheapest methods of removing some metals from solution, giving a plant of low first cost and supplying a source of cheap ferrous sulfate. The other ingredient needed for the process is SO2 roaster gas; the addition of which, as, described below, will give both ferric sulfate and sulfuric acid. Where roaster gas is a waste or obnoxious, product, the expense. for materials is still further lessened. The use of ferric sulfate and sulfuric acid as a solvent lends itself, well to the utilization of scrap iron as a precipitant, and the stages of the process fit in well together as an economic whole.

Jan 8, 1925

By Lloyd H. Banning

ELECTRIC smelting tests were conducted at the Northwest Electro-development Experiment Station, Albany, Oreg., to develop a feasible process for producing silicomanganese from siliceous manganiferous material. The Jackson County, Oreg., material used was massive and contained rhodonite as the most abundant mineral. Both raw and beneficiated materials were tested; various proportions and types of fluxes and reductants were used to make up the furnace charges. The silicomanganese product was used successfully in manufacturing various steels at industrial plants. The manganese content of the samples ranged from 23 to 28 percent; silica plus alumina content was as high as 55 percent-about four times the maximum specification for Metallurgical-grade ore. Sink-float laboratory tests indicated that the manganiferous material was amenable to beneficiation. Over 2 tons of rhodonite concentrate was prepared for smelting tests in a sink-float operation. Only the minus-3/4-inch, plus-8-mesh fraction was fed to a heavy-medium cone; over 97 percent of the manganese was recovered in the sink product, which contained 32.4 percent manganese and 44 percent silica plus alumina. About 25 percent of the silica was removed in the float product.

Jan 1, 1959

By M Brady, O Salisbury, C Claassen, B Beamish, H Baxter

Monitoring for signs of elevated spontaneous combustion in the active goaf behind the longwall face is crucial for early intervention of any potential heating incidents. Typically, trigger action response plans (TARPs) are established at the start of longwall mining and often are only reviewed when triggers are activated frequently and become ‘nuisance alarms’, or in the worst case scenario after a heating event. Narrabri Mine has adopted a proactive approach of reviewing the longwall active goaf spontaneous combustion monitoring TARP at the commencement of each longwall block and prior to reaching a known ‘mylonite zone’ of crushed coal, which is associated with increased coal oxidation. The review is based on information recorded from the monitoring data of the previous longwall blocks as well as interpretation of relevant spontaneous combustion propensity results for the coal. This has resulted in the mine implementing a zoned TARP approach for each longwall block covering both the longwall retreat through normal undisturbed coal and the zone where the goaf is influenced by the increased coal oxidation associated with the mylonite coal. The consequence of this approach is that it has removed the issue of having nuisance triggers being activated during mining through a known increased oxidation zone, while maintaining a high awareness of indicators of spontaneous combustion.CITATION:Baxter, H, Claassen, C, Salisbury, O, Brady, M and Beamish, B, 2015. Implementation of a zoned trigger action response plan associated with changing mine conditions at Narrabri Mine, in Proceedings The Australian Mine Ventilation Conference, pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of elastomeric noise abatement materials with a limited effort expended on the evaluation of specific treatments applied to mine timbers. Under the conditions employed, for a dimethyl silicone rubber, formaldehyde presented the major toxic threat; acrolein was the main toxic species for both polyester and polyether urethanes and an acrylonitrile-butadiene-styrene resin; in the case of flame-retardant styrene-butadiene rubber compositions, hydrogen chloride, and in the case of PFA-treated timber, furfural, were the major toxic compounds. Of the materials studied, the flame-retardant styrene-butadiene rubbers presented the greatest toxic hazard. The generated data have been reduced to toxic load tabulations amenable to employment for potential hazard assessment.

Jan 1, 1982

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) am-mines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Jan 1, 2011

By Reinhardt Thiessen

Views and conceptions of the origin, composition, and general nature of coal differ so widely that to determine the real extent of actual knowledge is no easy matter. The chemist finds difficulty in attacking the chemical problems and the engineer lacks a broad chemical basis for the study of his problems. Thus the economical and efficient utilization of coal in the industries suffers from a lack of knowledge of the composition of coal itself. Most scientists interested in this matter, as has been brought out in discussions during the recent investigation of coal problems, appear to have only a vague idea of the components of coal and their origin. Some are even in doubt as to whether substances derived from the wood and resins of plants form a part of coal; and few seem to have more than the dimmest idea of what are the components of coal, the condition in which these now exist, and the transformations that they haye undergone. Although during the paiilt century or more many co.rrect observations have been made and recorded, these were falsely or inadequately interpreted, so that many of the interpretations rendered are contradictory. As a result there has been great confusion. Many of the observations made in the past, although accurate and correct, could not be explained, because the principles involved in a correct solution of the problem were not then known. For example, Parkinson, Hutton, Petzhold, Guembel, and others made valuable discoveries regarding the processes by which plant substances are transformed into coal, but as the principles involved are those of colloidal chemistry, a science not known to the scientific world of that time, the observed facts could not be interpreted and the solution of the whole problem was blocked. The explanation of the true meaning of the alternating bright and dull bands so familiar in all ordinary bituminous coals afforCls another example. This banding has been observed and recorded from the earliest times, and has led to the forming of many false theories. Some gAologists, for example, have endeavored to explain the bands as due to alternating climatic conditions during the coal-forming period. Had the geologists known the true nature of coal they could not have made this mistake nor many others made in the past. To fill in a few of these gaps and to clarify some of the existing confusion is the aim of this paper. The immediate cause that led the author to investigate further the composition of coal and the origin and structure of its constituents was that when an attempt was made to discover the meaning of the coking and noncoking properties of coal a more exact knowledge of the nature of coal was required than was then available.

Jan 1, 1920

The Mount Angelo prospect outcrops as two copper rich gossans, the larger of which is 250 ft long and 70 ftwide. The mineralization is epigenetic and replaces part of a brecciated and disturbed lime tone and calcareou sediment sequence.Magnetic and self potential survey indicated a substantial body of sulphide mineralization, the top of which was approximately 100 ft below the surface.Diamond drilling confirmed this and established the presence of a mineral body of at least 500,000 tons, extending to a depth of 300 ft. Of the 500,000 tons, 200,000 ton are primary copper ore which a ays 2 per cent copper.This mineral body is not economic at present, but could become economic if copper mining is established elsewhere in the district...

Jan 1, 1966

By Tatsuya Oki

Tantalum capacitors can be found mounted on printed circuit boards of domestic appliances such as personal computers. These capacitors contain a considerable quantity of expensive metal tantalum and can be detached and liberated from printed circuit boards by impact breakers. In this study, the size and density distribution of the liberated electronic devices were investigated. Then, tantalum capacitors were recovered from other electronic devices using size separation and pneumatic gravity concentration methods. More than 70% of Newton's separation efficiency was obtained for tantalum capacitors. High Newton's separation efficiency could be also obtained for other types of electronic devices such as chip resistors.

Jan 1, 2011

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

By J. A. L. Napier

This paper presents an overview of work carried out by the CSIR Division of Mining Technology and formerly by the Chamber of Mines Research Organization (COMRO) to quantify the behaviour of the stope fracture zone near deep level goldmine stopes. The motivation for this work is first reviewed in the context of the unsatisfactory status of current mine layout design criteria. Numerical methods to represent failure processes are reviewed briefly. Specific studies of microfracture processes are described as well as physical modelling experiments that can yield insights into deformation mechanisms. Modelling of stope scale deformation mechanisms are presented and considerations relating to elastodynamic modelling of the rock mass are described. The implications of this understanding in relation to prospects for active fracture zone ?engineering? are outlined and finally, the directions of future research work are proposed.

Jan 1, 1997

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., Son Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Geologist-Petrographer. Experienced subsurface geology and petrographic rock and mineral identification. Desires position as either geologist or petrographer. M-682. Geologist, 36, married, employed. Nine years' experience geology connected with engineering, includes planning and supervising core drilling programs, study of stratigraphy and structure, special problems, report writing. Three years' teaching experience. Desires responsible position offering opportunity for advancement with progressive concern. Will travel part time. Available reasonable notice. M-683. Mining Executive with record of accomplishment organizing and directing efficient low cost mining and ore dressing operations available for position in the United States. Broad experience engineering, mechanized mining, flotation, safety, union labor relations and preparation of reports. Married. Employed; available upon reasonable notice. M-684.

Jan 1, 1952

By Derek Brennan, Donald Brennan

"The existing Rondout West Branch Tunnel (RWBT) is part of the Delaware Aqueduct which has been in service since 1944 and accounts for more than 50 percent of New York City’s water supply. In early 2015, the New York City Department of Environmental Protection contracted Kiewit-Shea Constructors, AJV (KSC) to construct the Rondout West Branch Bypass Tunnel project (Rondout) in order to mitigate the leakage of 132 million L/ day (35 million gpd) of water from two areas of the existing tunnel; the Roseton and Wawarsing areas.The scope of the Bypass Tunnel 2 project is separated into two distinct phases. Phase 1 consists of completing the shaft sinking to a depth of approximately 274 m (900 ft) at shaft 5B, 213 m (700 ft) at shaft 6B and the excavation of approximately 3,850 m (12,500 linear ft) of tunnel at a diameter of 6.6 m (21 ft 7 in). This phase also includes the installation of 2,804 m (9,200 linear ft) of 4.8 m (16 ft) diameter steel interliner pipe through the new bypass tunnel with cast-in–place concrete liner for a finished diameter of 4.2 m (14 ft). Access chambers at the top of shafts 5B and 6B will be constructed for access and housing of the mechanical and electrical equipment for supporting pumps and valves.Included in phase 2 is the additional excavation from shafts 5B and 6B to the RWBT, and the drainage tunnel to remove ground water infiltration from RWBT. This work will be completed during a scheduled shutdown of the RWBT and will include approximately 31 m (100 ft) of excavation of the two connection tunnels. Additionally, construction of the permanent plugs within the RWBT will be undertaken. Figure 2 shows the layout of the work.Access to the work through the deep shaft at site 5B was critical to the success of the project. The hoisting system needed to be multi-functional to handle the different types of construction from drill and shoot of the shaft, starter and tail tunnel, the assembly of the tunnel boring machine (TBM), the excavation of the TBM tunnel including the supply of the precast segmental liner, the grouting operations, the installation of the steel interliner pipe and the cast-in-place concrete as well as ingress and egress of personnel. The production of the TBM operations was critical to the schedule of the project. This required a quick cycle for muck haulage and supply of the precast segmental liner in order to keep pace with the excavation time of the TBM. For TBM assembly, components were limited to a maximum weight of 104 t (115 st) for a single lift. Various cranes were analyzed for hoisting, however, none would meet all of the citeria. Therefore, the project team selected a specialized hoisting system designed in house in conjunction with Timberland Equipment Ltd. that consisted of a total of 14 separate hoists and winches with a total of more than 2,833 kW (3,800 hp)."

Mar 1, 2019