Search Documents

By A. G. Pasamehmetoglu, N. Bolukbasi, O. Koncagul

A study has been undertaken to establish the relationships between the O&K wedge test cutting resistances and the geotechnical parameters of rock materials in the context of bucket-wheel excavator operation. Prediction equations were formed to estimate the cutting resistance from the geotechnical parameters by multiple regression analysis. The cone indentor index, uniaxial compressive strength and Shore hardness parameters have been found to be the most significant predictors

Sep 1, 1991

By R. Altindag

In rock cutting mechanics, the effects of the rock and coal brittleness on the efficiency of cutting bits are examined by many researchers. There is no universally accepted brittleness concept as a measure of cutting efficiency. The effect of the brittleness on rock cutting has not been completely explained. The aim of this study is to correlate the relationships between Specific Energy (SE) and brittleness concepts. The applicability of various brittleness measurement methods for rock cutting efficiency has been investigated. In this study, the raw data derived from previous experimental studies were used, and the relationships between SE and brittleness concepts were investigated. The two previously used brittleness concepts, which are named as B1 (the ratio of compressive strength to tensile strength) and B2 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), and a new introduced brittleness concept named B3 (the area under line in relation to compressive strength and tensile strength) were evaluated in this study. The relations among these brittleness concepts for rock cutting efficiency were established using regression analysis. There is no correlation found between the SE values and the brittleness of B1and B2values. But, the SE is strongly correlated with the brittleness of B3. It was seen that the suggested brittleness of B3concept could be used as an indicator in rock cutting efficiency analysis.

Jan 1, 2003

By R. W. Drier

THE conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in property or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology. This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest.

Jan 1, 1929

Based on relative CO2, N2, and 3He contents, geothermal systems of the Taupo Volcanic Zone, TVZ, can be subdivided into two major groups: arc-type systems, associated with andesitic magmatism along the eastern boundary of the TVZ, and rift-type systems over its western parts. The highly increased N2/3He, CO2/3He and CO2/Cl ratios of the former are ascribed to entrainment of large proportions of volatiles of subducted, marine sedimentary origin. The largely rhyolitic, rift-type magmas are assumed to have formed from volatile-depleted, residual melts. Correlations of Cl and CO2 with heat contents suggest that formation of the two types of source magmas involves mixing of two end member components: a low-volatile melt with a heat/Cl ratio of 25 Ml/mol (0.7 MJ/g), and a low Cl vapor with a heat/CO2 ratio of 5 Ml/mol. On the basis of these values, the heat associated with andesitic magmas is found to be carried in close to equal parts by both vapor and melt; for the rhyolitic melts the proportion contributed from the vapor is only about 2%. The heat/He ratios of the rhyolitic source magmas for the rift-type geothermal discharges from the TVZ of 0.12¦0.05 Ml/pmol is within the range of 0.05 to 0.2 Ml/pmol of the upper mantle. The higher heat/3He ratios for the arc-related magmas of 0.4¦0.2 Ml/pmol are likely to be due to the high proportions of heat carried in the form of a separate, low 3He vapor phase derived largely from subducted sediments.

Jan 1, 1995

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and Mineral Processing Systems (MPSI) merged, a unique opportunity occurred for two independent mill fabricators to compare design pro¬cedures and the research upon which they were based. Several semiautogenuous (SAG) mill analyses are compared using Boliden Allis and MPSI methods. The differences and similarities are then used in a correlation of critical stress definitions and the acceptable design and inspection criteria. Given the opportunity to compare the total philosophies and methods of several companies involved in the design and fabrication of grinding mills, it was important to first develop the comparison method and ground rules. One option was to compare analytical methods by details such as numerical techniques and accuracies. However, this option was discarded in favor of a more general approach. The question that was finally posed was in two parts. Given an identical mill requirement: • What would be the difference in the analytical design result, and to what aspect of the analytical process could this difference be attributed? • What would be the difference in approaches to obtaining the final hardware in subcontracting, both in specifying and Quality Assurance surveillance? By using this comparative approach, questions of relative conservativeness and reliability would automatically be answered.

Jan 1, 1992

The captions to Figs. 1 and 2 of the paper by B. J. Parry entitled 'High-strength cold-rolled steels' should read as follows:

Jan 1, 1984

By F. Charette

The paper reviews recent investigations of the impact of corrosion on the performance of both plain and coated Swellex rock bolts. It addresses the problems associated with estimating and predicting corrosion rates of friction bolts, and based on field data it suggests an empirical relationship to predict corrosion rates. A review of the necessary qualities for a protective coating leads to recent experience with coated Swellex bolts that suggest that they can contribute to extending the useful life of Swellex bolts in potentially corrosive environments.

May 1, 2004

By K. R. Nichol

The author points out that corrosion works 24 hours a day, every day. It is an economic reality that the cost of corrosion is inevitable and that its cost should be incurred in the least expensive way. An economic evaluation technique to properly assess its relative impact is the Discounted Cash Flow Method. Various remedial and corrosion control measures are available and these, when coupled with a planned corrosion control program, help reduce the cost of corrosion.

Jan 1, 1973

By V. Brabie, S. Jansson, L. Bohlin

The rate of dissolution of solid MgO-C and doloma into liquid in CaO-Al2O3-SiO2-MgO slag at different temperatures was studied under conditions of forced convection by rotating cylindrical refractory specimens in a stationary crucible containing the molten slag. The corrosion rate was calculated from the change in diameter of the cylindrical specimens. Refractory specimens were 13 mm in diameter and 70 mm long. The specimens were rotated for15 to 120 minutes at speeds of 100 to 400 rpm in the molten slag. The rate of corrosion increased with temperature and with the rotating speed of the rod, and decreased when the slag was nearly saturated with MgO. The experimental results confirm the assumption that the diffusion of magnesium oxide through the slag phase boundary layer controls the corrosion process. The corrosion mechanism seems to be the dissolution of the refractory materials into the slag, followed by penetration of pores and grain boundaries and dispersion of the grains in the slag. Keywords: MgO-C refractory, doloma refractory, molten slag, corrosion rate, corrosion mechanism

Jan 1, 2004

By Z. W. Nkosi, M. Sephton, J. H. Potgieter

The exhaust system is a complex assembly of various components performing important tasks in harsh environments. Carbon steels have been used extensively in exhaust systems, but pressure for lower cost, increased fuel efficiency; lower hazardous emissions, weight savings and increased life expectancy have shifted the emphasis to stainless steels. In response to the growing consumption of stainless steels in automotive exhaust systems, the need to properly evaluate their corrosion resistance properties in order to ensure their appropriate use, has increased substantially. This paper evaluated the most common corrosion and oxidation tests developed that are used and applied it to four common stainless steels often employed in hot end exhaust components. In a summary considering the weight loss of an alloy, it general corrosion rate and pitting resistance under all the test conditions for hot end exhaust components, results indicate that 434 was by far the most corrosion resistant alloy, followed by 1.4509 and 321, and lastly 304 was the least corrosion resistant. In general, the ferritic stainless steels, especially 434, outperformed the austenitic ones under all the test conditions.

Jan 1, 2006

By Jerry Gagnon, Matt Burr, Dave Evans, Timothy Ellis, Davies Kakengela, Abbas Mirza, Larry Webb, François Leclercq, Andrew Johnston

Lead-based alloys are the primary anodes used in electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present day lead-calcium-tin alloys for copper electrowinning and lead-silver alloys for zinc electrowinning. It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. The desire to minimize grain boundary corrosion by a balance of alloying element selection and microstructural design allows the grain boundary area to be engineered. However, operational issues can lead to unexpected corrosion behaviours which we will discuss moving forward. The comments in this work, though directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The lifecycle of electrowinning anodes is dependent upon electrowinning tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead electrowinning anodes.

Jan 1, 2015

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognised and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economical restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist with respect to the application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2006

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognized and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economic restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist about application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2007

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

By R. F. Lynch, F. E. Goodwin, A. F. Skenazi

"The Gal/an alloy has been developed for continuous galvanizing of steel. The choice of the eutectic zinc-aluminum alloy with addition of misch metal gives a coating with specific characteristics as far as structure, analysis, surface chemistry and surface morphology are concerned. The performance of the uncoated Galfan coating is superior when compared to conventional galvanized particularly for corrosion resistance and ductility. For coil coating applications, these two assets are of the utmost importance but in order to benefit from these two advantages, good paint adherence and high resistance to edge creep and blistering have to be obtained. Despite Galfan's unique features compared to other zinc based or aluminum zinc based coatings, existing pretreatments and painting conditions are used with only minor modifications in order to assure good adherence and edge creep resistance. With compatible processing, Galfan can outperform galvanized and Galvalume as a substrate for coil coating as is demonstrated with various test results.IntroductionThe technical and commercial development of Galfan, a 95% zinc-5% aluminum-0.1% lanthanum-cerium hot-dip coating for steel, has been rapid. From its identification as a promising coating in late 1980, it has evolved from a research product to a fully commercial product with over 100 000 metric tons of coated sheet produced to date, and another 90 000 tons, at minimum, scheduled for 1986. The great majority of tonnage produced to date has been coil coated for use in building panel , appliance, and similar applications. Much technical work has been done to determine the suitability of Galfan for these applications and the proper way of processing sheet for best results. The present state of knowledge is discussed in this paper, along with some recent applications which are given asexamples"

Jan 1, 1987

By Dr. G. R. Hoey

"Abrasive wear and corrosive wear of carbon-steel grinding balls occurred simultaneously during the wet-grinding of hematite iron ore, and Ni-Cu sulphide ore, in laboratory ball mills. Two corrosion control methods, the use of corrosion inhibitors and pH control, were investigated and found to be effective means of reducing or preventing corrosive wear. Up to 50 % reduction of total ball wear resulted from the use of these methods.Corrosive wear is caused principally by the reaction of oxygen in air with the carbon-steel grinding balls, probably by the following reaction: 2Fe + O2 + 2H20 - 2Fe2 + 40H-.IntroductionA survey of corrosion problems in Canadian sulphide ore mines was completed and the findings were published in 197l(l). The corrosion survey was used to develop the present research program with the objective to find more economical and effective ways and means to reduce the corrosion that occurs in the mining and metallurgical industry. The purpose of this presentation is to review the projects being done by staff members of the Corrosion Section, Extraction Metallurgy Division, on corrosive wear and its control in wet-grind ball mills.Both abrasion and corrosion contribute to metal consumption during wet grinding of ores. The total wear of grinding media in this study is assumed to be equal to the sum of corrosive wear and abrasive wear. A great deal of research and development has been reported in the literature on ways to improve the abrasion resistance of grinding media but only a small number of studies has been reported on the corrosion resistance of conventional grinding media."

Jan 1, 1974

By Freeman C, Dingley W

Addition of sodium nitrite-borax, sodium hydroxide, sodIUm carbonate, lime, or sodium silicate reduced wear of forged steel balls and cast iron slugs in wet grinding a complex zinc-lead-copper sulphide ore in laboratory ball mills. Maximum wear reductions were 27 per cent (forged steel balls) and 33 per cent (cast iron slugs) with sodium hydroxide and nitrite-borax additives respectively.Potential measurements of balls and slugs during grinding, and analysis of the data in terms of corrosion theory demonstrated that corrosive wear had been reduced or prevented by these additives. Actual per cent wear reductions were not equated to the rate of corrosive wear because of the undefined interdependence between abrasion and corrosion in wear processes. The investigation verifies that in laboratory ball mills corrosion is significant in the wear of grinding media and wear can be reduced by corrosion inhibition and pH adjustment.

Jan 1, 1978

By Benjamin A. Allou

La seule production de columbo-tantalite réalisée en Côte d?Ivoire est effectuée dans les éluvions et alluvions du gisement d?Issia, localisé au Centre- Ouest de la Côte d?Ivoire. Même si un lien direct avec les roches granitiques est suspecté, aucune attention particulière n?a été accordée à l?étude de la minéralisation primaire en relation avec l?évolution des granites et des pegmatites associées. Ces granites, qui sont en intrusion dans les roches sédimentaires du Protérozoïque inférieur, comprennent : le granite orienté à deux micas (Lobo), le granite orienté à muscovite dominante (Bitapia) et le granite porphyroïde non orienté à muscovite dominante (Issia). Les résultats de cette étude indiquent que les pegmatites à Nb-Ta-Be-Li sont liées au granite de type Issia. Les observations de terrain et les analyses sur roche totale des granites montrent que: (1) les trois principaux granites de la région sont de type- S et peralumineux dans leur composition, (2) ils ont été formés pendant la période tardi- à post-Éburnéenne, (3) le granite d?Issia fut le dernier à se mettre en place. Les pegmatites liées au granite d?Issia ont été classées en quatre types : Apegmatites stériles; B- pegmatites à Be; C- pegmatites zonées à Nb-Ta-Be; et Dpegmatites zonées à Be-Nb-Ta-Li. Les pegmatites zonées comprennent les zones suivantes: I- zone à aplite; II- zone graphique; III- zone à albite, microcline, béryl et columbo-tantalite; IV - zone à microcline massive; V- zone à quartz. Ces pegmatites présentent une zone d?altération métasomatique externe. La minéralisation de Ta, Nb et Be est liées à la zone III des pegmatites de types C et D, et celle de Li est associée aux greisens qui peuvent être observés n?importe où dans les pegmatites de type D. Les données de terrain et de laboratoire indiquent que le granite d?Issia est la roche parentale des pegmatites à éléments rares de la région. Les pegmatites minéralisées sont distribuées seulement autour du granite d?Issia et les patrons des terres rares des granites et ceux des pegmatites à éléments rares sont très similaires. Les analyses de la composition totale montrent un lien génétique entre le granite d?Issia et les pegmatites à éléments rares. Il est suggéré que les pegmatites ont été formées durant le transport et la cristallisation fractionnée du magma.

May 1, 2003

By P. K. Chatterjee, G. D. Just

Sublevel open stoping is a low-cost method that has been successfully employed in many large underground mining operations. Where ore body characteristics are suitable, extensive mechanization and the use of large-scale stoping techniques can considerably reduce operating costs. However, careful long-term planning of mine layouts and large capital commitments in development are required prior to production. Implementing precise mine design procedures and carefully controlling operations can result in considerable benefits. This article describes methods to achieve these objectives based largely on mining operations at Mount Isa, where sublevel open stoping has been used since 1932. Ore won by this method accounted for a very large percentage of the total tonnage produced at Mount Isa. Major costs associated with sublevel open stoping can be classified as drilling, explosives and charging, and LHD costs. In this article, analyses of these costs are made with particular reference to stope design. Parameters such as burden, drill hole diameter, explosive density, specific charge, etc., are considered in establishing the interrelationship of unit operating costs, as well as total costs of sublevel open stoping.

Jan 10, 1981