Search Documents

By Jarrod Bonsmann

"This paper presents the results of small scale testing to examine the effect of various importantparameters on the response of a vehicle due to the detonation of an explosive charge buried inthe soil below the vehicle. In particular, we were interested in examining what effect change instandoff distance, change in mass, and change in surface area would have on the loading applied.We examined the impulse delivered to the target in all cases and for the change in mass andchange in stand-off distance we examined impulse, kinetic energy, and acceleration."

Jan 1, 2012

By S Adamson

Morphological analysis of alluvial gold recovered from the same segment of a placer by four common commercial methods indicates that gold shape and the presence of quartz intergrowths or sulphide overgrowths substantially influence the recovery efficiency of each method. The amount and types of gold saved by each method varies according to the different hydrodynamic conditions under which each of the methods operates. Reverse circulation drilling has the lowest efficiency and preferentially loses moderate-high flatness gold and intergrown or overgrown gold particles with relatively low density. Gravity riffle, hydraulic riffle, and jigcentrifugal concentrator systems respectively save progressively more of these problematic gold morphotypes, but still lose significant and sometimes substantial amounts (of profit) to the tailings. Because of the differences in recovery efficiency, reverse circulation drilling probably underestimates the grade of most placers and may have resulted in bypassing several economic deposits. Losses to tailings by commercial recovery plants arise from inadequacies in fundamental plant design features. These inadequacies compromise plant efficiency by limiting the ability of plants to simulate the wide range of hydrodynamic conditions necessary to operate effectively throughout placer systems. Incorporation of sand pumps and multiple recovery methods into the more sophisticated plants only partly overcomes these inadequacies. At best, efficiency will be maximised in a few segments of the placer determined by individual plant design, and will decrease progressively upstream and downstream of those segments. Without prior knowledge of the morphological characteristics of the gold to be mined, it is difficult to choose the most appropriate plant design, or to estimate what proportion of the gold will be recoverable by any given plant. If the relevant relationships are not considered beforehand, the recovery plant is likely to lose a significant proportion of the gold, and sacrifice maximum profit.

Jan 1, 2001

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By Andre Zingano

The objective of this paper is to study the effect of annulus thickness on the quality of resin mixture for fully grouted resin bolt. Pullout and mixture tests were made in underground coal mines for the following arrangements: (a) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with steel wire around the roof bolt; (b) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt; and (c) borehole diameter 0.95 in. (24 mm) and a roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt. The mixture test in steel pipe showed that the best resin mixture is for borehole with 0.95 in. (24 mm). The arrangement (b) produced big voids around the bolt. But for the 0.95 in. (24 mm) hole, arrangement c, the mixture was the best. It was corroborated with the pullout tests results where there is a difference in grout stiffness: the 0.95 in. (24 mm) borehole is about 10 times higher than a borehole with diameter 1.14 in. (29 mm). On the other hand, for the cohesive strength the difference is not significant. Numerical models were built to simulate the pullout tests, and also to simulate the roof support at an intersection. Convergence at two underground intersections, consisting of an immediate roof with laminated sandstone, was monitored to evaluate the performance of the roof supports, using the 1.14 and 0.95 in. (29 and 24 mm) diameter boreholes (i.e. arrangements ?a? and ?b?). The convergence readings showed that the 0.95 in. (24 mm) borehole diameter resulted in a smaller, although it was not significantly different.

Jan 1, 2008

A rough simulated borehole has been developed for the installation and dynamic testing of rock bolts a the WASM Dynamic Test Facility. The rough simulated borehole is used for rock bolts that are sensitive to equipment installation technique or borehole geometry (particularly friction rock stabilisers and resin encapsulated bolts). An extensive axial test program has quantified a difference between the static and dynamic capacity (kN/m of embedment) for friction rock stabilisers once sliding starts. The 47mm split tube bolt has a 50% reduction in embedment capacity (but with significant variation) dissipating 2.7kJ/100mm of sliding per meter of embedment, and the Omega (inflatable) bolt had a 70% reduction in embedment capacity dissipating 6.2kJ/100mm of sliding per meter of embedment. The Omega bolt dynamic capacity remainder at least equivalent to the split tube bolt static capacity.

May 1, 2009

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001

By Belcher C. B

The Groote Eylandt manganese ore deposits contain mainly pyrolusite and cryptomelane with lesser amounts of the manganese minerals lithiophorite, todorokite, psilomelane, and nsutite. The major non-manganese minerals which occur are quartz, kaolinite, and goethite.Determination of the mineralogy relies mainly on x-ray diffraction analysis. Quantitative methods for the determination of pymlusite and cryptomelane in Groote Eylandt manganese ores have been developed, A large amount of isomorphous substitution may occur in the manganese minerals and a number of minor and trace element associations have been noted. A correlation has been established between the potassium and cryptomelane contents for a wide range of ore types. Anomalous calcium, magnesium, and sodium values occur in samples containing todorokite, and barium is associated with psilomelane. Groote Eylandt lithiophorite appears to contain negligible amounts of lithium (<O· 05 per cent).A relationship between the H20+ and the Al203, K20, and Fe203 contents has been estahlished indicating that much of the combined water content is due to the presence of kaolinite and goethite, and cap be removed by beneficiation of the ore.

Jan 1, 1975

By A. T. Haile

Detailed monitoring of the response of the rock mass between rockbolt reinforcement units subjected to a simulated seismic source has been successfully conducted. This work has shown the increase in amplification of the Peak Particle Velocity (PPV) with distance from a rock bolt unit, and, a minimum PPV for rockburst damage for the given site characteristics. This understanding, at this site, will allow the design of a suitable rock bolt spacing to prevent unravelling of the rock mass between the rock bolt units for a given level of seismicity. Or, alternatively, an estimation of the requirement for a suitable fabric support system, for the anticipated level of seismicity, can be made.

Jan 1, 2001

By Dongok Kim

Regardless of the advantages of the Friction Stir Process (FSP), for age-hardened aluminum alloys, the mechanical properties such as hardness in the stir zone decreased after FSP due to the growth or dissolution of strengthening precipitates. Here, as a new technique, FSP was introduced to alloy copper nanopowders in Al7075 T651. Mechanical properties of copper nanopowder- alloyed Al7075 T651 together with micro and nanostructures were compared with those of as-FSPed Al7075 T651 using SEM, TEM, and Vickers hardness testing to understand structure-property relationships. It was observed that Vickers hardness of the stir zone in copper nanopowder alloyed Al7075 T651 increased by 20% compared to that of the heat affected zone, while the as-FSPed samples did not show a noticeable increase in hardness in the same zone. Xray mapping showed traces of copper nanopowder after the process. TEM is being used to verify if there was CuAl2 formed in the copper alloyed sample.

Jan 1, 2006

By Juan Carlos Lozada

YURA S.A. es una empresa industrial cuyo principal actividad es la fabricación y comercialización de Cementos Portland y adicionados, conglomerados de albañilería y concretos. Asimismo proyecta la construcción de una nueva línea de producción de Clinker. En ese sentido, el presente texto señala el sistema de gestión que se utilizó para mejorar las prácticas sugeridas por el PMI (Project Management Institute) en la Guía del PMBOK, y cómo se aplicaron las diferentes herramientas a las situaciones particulares del mismo.

Sep 12, 2011

By Raymond J. Castelli

The paper provides a general overview of the numerous types of earth retaining systems currently available, and organizes these various systems by several classification methods. These classifications can be used as a guide in identifying the appropriate type wall or walls for any specific project application. As a further aid in sorting through the numerous wall alternatives for a specific design or construction project application, the paper suggests a systematic approach for wall selection, and presents helpful charts summarizing the general advantages and disadvantages, and typical limitations for the currently available wall systems.

Jan 1, 2003

By A. Sobhy

Froth flotation is a widely used, cost effective coal cleaning process. However, its high process efficiency is limited to a narrow particle size range between approximately 50 to 600 µm for coal and 10 to 100 µm for minerals. Beyond this range, the efficiency of froth flotation decreases sharply, especially for difficult-to-float coal fines of weak hydrophobicity (e.g., oxidized coal). This study was aimed at enhancing recovery of an Illinois fine coal sample using a flotation column featuring a hydrodynamic cavitation nanobubble generator. Nanobubbles that are mostly smaller than 1 µm can be formed selectively on hydrophobic coal particles from dissolved air in fine coal slurry. Results indicate that combustible recovery of a -150 µm coal was increased by 5-50% for different size fractions in presence of nanobubbles, depending on process operating conditions. Other major advantages of the nanobubble flotation process include lower collector dosage and air consumption since nanobubbles are produced from air naturally dissolved in water and they act as a secondary collector on particle surfaces, thereby resulting in considerably lower operating costs. Key words: Cavitation; coal; froth flotation; nanobubble.

Feb 27, 2013

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

By L Hussey, H Thanasekaran, J Kohmuench

Conventional flotation technology has historically failed to achieve high recoveries when treating <15 µm particles (Lynch et al, 1981). The new StackCell™ flotation technology was developed to specifically target this particle size range, and was tested at pilot plant scale at Mt Keith Nickel Concentrator. The streams tested, Slimes Rougher Tailings and Fines/Slimes Cleaner Tailings, represent 21% and 11% of the total nickel lost to tailings in the plant. Laboratory scale test work indicated that an economically significant fraction of these losses was consistently available to be recovered by additional flotation. The pilot plant experimental scope included over 50 tests. A grade recovery curve for each stream was developed, as well as information on the effect of ore type, feed rate, wash water, air flow, collector and frother on the performance of the cell. The single StackCell was able to achieve nickel recoveries of 16.8% and 16.5% on the Rougher Tailings and Cleaner Tailings, respectively, at grades consistent with these blocks. Additional test work of the StackCell in a cleaner scalper duty yielded final quality concentrate with a maximum nickel recovery of 59.5% for the single stage StackCell. Laboratory scale simulation of the downstream impacts of the StackCell operating as a cleaner scalper indicated a net recovery benefit of up to 2.0% for this cleaner block.Tests were completed to compare residence time requirements of the StackCell, as compared to conventional flotation. In 55 seconds, the pilot plant StackCell achieved 50% of the recovery of a 960 second laboratory scale conventional flotation on the same feed material. The apparent improvement in flotation kinetics is attributed to the novel high intensity aeration system, which provides efficient bubble-particle contact thereby shortening the residence time required to achieve high recoveries. The smaller footprint and lower energy costs of such a cell are also benefits of this technology, which is being considered for industrial scale installation as a result of this test work. Given the industry’s historical poor performance treating slimes with conventional flotation, it is clearly best practice to challenge the status quo through innovative new technology, such as the StackCell.CITATION:Hussey, L, Thanasekaran, H and Kohmuench, J, 2017. The application of high intensity flotation technology at Mt Keith nickel concentrator, in Proceedings MetPlant 2017, pp 259–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By B. Genc

After the explosion at Middelbult Colliery, South Africa in May1993, which claimed 53 lives, the South African Coal Mining Industry and the Safety In Mines Research Advisory Committee (SIMRAC) united forces to establish a surface facility to develop and test on-board flame suppression systems for continuous miners and roadheaders. The first test that was conducted in this newly constructed test tunnel at the Kloppersbos Research Facility, CSIR was in July 1995.Since then 70 tests have been conducted using the facility and have focused on on-board active ignition suppression systems for continuous miners (CM) and road heading (RH) machines to enhance the safety of South African mine workers in collieries. These suppression systems are mounted on the CM or RH machine and detect the occurrence of an ignition by means of light-sensitive sensors. The electronic signal from the sensor triggers the suppression system, creating a flame-suppression curtain, containing and extinguishing the flame in the immediate vicinity of the ignition. Forty-three tests have been conducted with an active on-board suppression system present inside the test tunnel. Since flame propagation speed is an extremely important parameter, the CSIR-Miningtek made the results of the test programme available for re-analysis. Flame speed depended on whether a machine was present in the heading or not, the geometry of the heading and the volume and composition of the explosive mixture of gas. Flame speeds of up to 190 m/s were recorded. However, the active suppression systems were almost always successful in containing flame propagation.

Jan 1, 2002

By S Reid, W Chen, T J. Donohue, A Katterfeld

The use of discrete element modelling (DEM) is widespread in the materials handling field, and is used for many applications. One of the important limitations in using DEM is the number of particles that can be modelled, with this limitation often resulting in increasing the minimum particle size in the simulation. This restriction on minimum particle size is usually accommodated in the calibration process where the parameters in the simulation are chosen in such a way as to reflect the presence of smaller sized particles, and in typical applications such as transfer chutes this is standard practice. However, in the application of vibrating screens the inclusion of the ‘fines’ is critically important due to their influence on the screening efficiency. In reality, the presence of fines reduces the screening efficiency for a number of reasons; however, the main mechanism that will be addressed in this study is the effect of adhering fines. This is where the fines adhere to the larger particles and are carried over into the lump stream. The approach for this study will be to firstly consider the relatively simple mechanical sieving process used in the determination of particle size distribution, and then this will be expanded to consider the application of vibrating screens.CITATION:Donohue, T J, Chen, W, Katterfeld, A and Reid, S, 2017. Addressing the challenges associated with the modelling of iron ore in vibrating screens, in Proceedings Iron Ore 2017, pp 155–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Attractive geology does not guarantee mining investment if a region’s policies are bad, according to mining executives surveyed in the Fraser Institute’s seventh Annual Survey of Mining Companies. Companies responsible for a combined US$642.4 million in international exploration (during 2002) rated the policy attractiveness and mineral attractiveness of mining jurisdictions around the world. Jurisdictions like Chile, Australia, Quebec and Nevada bolster their attractive geology with mining-friendly policies, the report said. These locations do well on the overall investment attractiveness index. On the other hand, jurisdictions like British Columbia and Indonesia, each with excellent geology, are hurt by their policies, which have lowered their score.

Jan 1, 2004

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

By Richard J. Mainiero

The Bureau of Mines has developed a prototype nonincendive explosive rock-breaker charge that can be fired unconfined in underground bituminous coal mines without the danger of igniting a flammable atmosphere that might be present. At present, unconfined shooting in underground coal mines is prohibited, but there are situations where the use of such shots would yield an overall improvement in safety. The charge consists of l-1/2 lb of permissible water gel explosive in the form of a short cylinder 7 inches in diameter and 7/8 inches high, surrounded by a l/2-inch-thick layer of damp salt, and encased in latex rubber reinforced with cheese cloth. The latex rubber housing provides a charge package that is strong enough to resist rough handling yet is pliable enough to conform to an irregular stone surface. A charge of this shape was found to be more effective at breaking rock than charges with lined or unlined cavities. Incendivity tests in a gallery have shown that the prototype charge will not ignite a flammable methane-air atmosphere when fired. Rock- breaking tests made with limestone boulders indicate that the charge will satisfactorily break stone slabs weighing 1 to 2 tons, and that two or more charges might be effective for slabs weighing up to 10 tons. In cooperation with the Mine Safety and Health Administration (MSHA), a test protocol for the certification of these charges as "permissible" for use in flammable atmospheres is being developed.

Apr 1, 1982

By Ali Porbaha

In today's fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Mass stabilization, Cut-Mix-Injection (FMI), and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002