Search Documents

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

In this study, the method of chemical co-precipitation?reduction?diffusion was developed for the preparation of magnetic SmCo5 alloy. In the chemical co-precipitation process, the effects of solution pH, the reactant concentration, the dispersant on the process were investigated. The optimum conditions of the process were determined, and the SmCo5 alloy oxide precursor particles with fine crystalline structure, narrow size distribution was obtained. Then, by reduction-diffusion treatment of the precursor particles, the SmCo5 alloy with high quality was produced. It is anticipated that the co-precipitation-reduction-diffusion is a novel method available for SmCo5 alloy production.

Jan 1, 2006

By Claude Bazin, Jalna Lamontagne

"The operators of mineral processing plants collect daily samples from strategic process streams with a view to prepare production balances to assess plant performances. The rules to minimize the risk of systematic sampling errors are known and applied in many mineral processing plants. The mass of the sample to be collected is calculated to yield a target measurement reproducibility considering the fundamental error associated to the sampling of heterogeneous material. This paper demonstrates that this practice is partly valid if one does not account for the time variation of the ore composition during the day. The concept is demonstrated using samples collected on a 30 minute basis from different streams of a gold ore concentrator. Results show that depending of the natural variability of the stream characteristics the mass of the daily samples may not be the critical variable to obtain reproducible measurements. On the other hand the number of cuts taken during the day could impact on the variance of the measurements obtained from daily samples.IntroductionMineral processing plants may treat several thousand tons of ore every day to produce concentrate or impure gold ingots. The operation and performances of these plants are monitored on a daily basis through the collection of ore samples from various streams of the processing circuit. The samples are prepared and assayed to obtain the concentrations of target elements that are subsequently used to calculate the mass flowrates in the streams of the circuit and ultimately the distribution of the target metals for the estimation of the plant performances (Morrison, 2009; Lachance and Leroux, 2016).The acquisition of representative and reproducible samples is therefore the first step in the characterization of plant performances. The term representative sample is used here to indicate an unbiased sample, i.e. a sampling procedure that does not introduce a systematic error. Rules for the collection of unbiased samples are reviewed in the literature by different authors (e.g. Morrison, 2009) and are not discussed in this paper. The term reproducible indicates the dispersion of the measurements around the average value of a characteristic of a stream meets an acceptable level of variance. The reproducibility of a measurement process (sampling and analysis) is assessed by the relative standard deviation or coefficient of variation of the measurement that is a function of the sampling and assaying errors (Morrison. 2009; Gy, 1979). Usually the focus is put on the fundamental error of sampling whose variance can be controlled by the choice of the primary sample mass or adequate particle size reduction during the preparation of secondary or tertiary samples extracted for the chemical analysis. When a sample is taken from a stream that exhibits a time varying characteristic, the obtained measurement exhibits a variability that is not only a function of the sample mass but also of the natural variability of the ore in the sampled stream. This paper examines this aspect of the sampling of a time varying process on the reproducibility of composite samples for a day of production."

Jan 1, 2017

By P. L. Swanson, F. M. Boler

The U.S. Bureau of Mimes conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic destressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 21/2-week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 1993

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By Steve Kral

For an industry that provides more than half of the nation’s energy needs, the U.S. coal industry still attracts negative publicity. However, the nation’s energy appetite continues to increase. And political leaders and the public are beginning to understand that alternative fuels will not be enough to keep up with that appetite. Does that mean the nation will now embrace the coal industry? No, according to speakers at the Rocky Mountain Coal Mining Institute (RMCMI) meeting. The industry still needs to sell the public on coal’s advantages over other fuels. And the industry must continue to develop technology that will allow coal to meet and exceed strict clean air and clean water regulations.

Jan 1, 2002

By Hamid Butt

Information Technology ??Advanced Information Technology is dramatically changing information flow within organizations. This enables employees to have information at their fingertips to make informed and prompt decisions. ??Real-time information allows timely analysis, which dramatically reduces cycle times, making organizations faster and more flexible. Business Challenges ??Continual growth of mining and Mine mobile fleet.??Increasing maintenance costs. ??Difficult to identify and troubleshoot equipment problems while equipment is operating. ??New equipment is increasing in complexity and cost. Therefore, each failure results in a greater impact to production and cost. ??Troubleshooting practice is reactive. ??Protect and optimize the use of mining assets to realize maximum business value. ??Maintenance and Operating information is not easily accessible ?no near real-time system that provides complete information.

May 1, 2006

By C. C. Oosthuizen

Paper written on project work carried out in partial fulfilment of Technikon Practical Training Frank shaft is mining both Merensky reef and UG2 reef. The Merensky orebody is almost depleted and this was the reason for starting to mine the UG2 ore reserves. It was decided to mine the UG2 orebody with trackless equipment using a bord and pillar mining method. Frank shaft has been mining the UG2 orebody for nearly 5 years. The T-cut mining method was introduced to see if it could improve the grade of the run of mine (ROM) as well the extraction percentage.

Jan 1, 2005

By Bruce W. Woolpert

During the SME Board of Directors’ midyear meeting in Monterey, CA Aug. 25, I discussed trends in the construction aggregates industry. Many construction-material suppliers may not have yet fully internalized the changes that are taking place. But the changes are significant. And they have shifted the focus in the aggregates industry from “assets” to “people and innovation.” Construction-material suppliers serve many customers. A typical quarrying operation at Graniterock would have more than 1,000 customers, mostly civil engineering contractors. Along with the push toward people and innovation, there is increased emphasis on vertical integration from aggregates to ready-mix concrete and hot mix asphalt, to final construction. If a company is not vertically integrated, it will at least have strong partnerships with other firms, to deliver a high-quality finished project on time.

Jan 1, 2002

By Edwards A. B

The occurrence of lollingite (FeAs2 ) in the Broken Hill lode is recorded by an analysis of lollingite published in the Annual Report of the Department of Mines, New South Wales, for the year 1934 (p. 69). The analysed specimen came from the North Broken Hill mine, and material from the same occurrence (Specimeh No. 1), as well as two specimens (Nos. 3 and 4) from the Zinc Corporation mine, have been forwarded· to us by Mr. M. Mawby of the Zinc Corporation Mine. This material has been supplemented by another specimen (No. 2) from the Zinc Corporation mine, passed over to us by Dr. I. Wark.The original analysis of lollingite is quoted in Table I, and shows that the Broken Hill lollingite contains appreciable amounts of cobalt and nickel, and, indicates that the iron is to a considerable extent replaced by cobalt and nickel, so that its formula should be written (FeCoNi) As2This is supported by a microscopical examination of a polished surface of the lollingite, in which no individual arsenides of cobalt and nickel can be detected.Coarse grained galena, sphalerite, chalcopyrite, and pyrite are attached to our specimen of lollingite from the North mine, and are separated by a sharp junction from a mass of lollingite associated with some arsenopyrite and garnet. The massive lollingite can be distinguished from arsenopyrite in the hand specimen by a much brighter, silvery lustre, against which arsenopyrite appears a dull silver grey; but the passage from lollingite to arsenopyrite appears transitional.

Jan 1, 1939

By Gennaro G. Marino

During the preliminary design stages of the Illinois Division of Natural Resources(DNR) building, it was discovered that an old coal mine was present some 70 m (220 ft) beneath the building site. The new DNR building to be constructed is 36 m (120 ft)wide and 134 m (440 ft) long. It has three stories above grade and abasement level. The building is oriented north-south and has east and west ponds next to it (Fig. 1). The building is located on the State Fairgrounds in Springfield, IL. Given the history of surface subsidence of these underground coal mines in the Springfield area, there was concern about the potential for future subsidence at the building site. Mine subsidence events in the area have resulted in more than 0.9 m (3 ft) of settlement and have caused significant structural damage.

Jan 1, 2000

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 61 surface coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, ?A Guide for the Evaluation of Human Exposure to Whole Body Vibration.? The comparison showed that about ha]f of all surface coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only on the order of 15% would be expected to experience vibration exceeding the exposure limit. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983

By James H. Prout

Roof warning signals were studied in 18 mines covering 5 coal seams. The results of this study confirmed that roof talk must be interpreted for each individual mine after all other conditions are present that indicate danger of roof fall. Characteristics of roof talk pulses were studied to ascertain features used in interpretation. Roof talk pulse decay time was found to be typically 0.1 to 0.5 seconds depending on the dimensions of the entires. Time between roof talk pulses was found to correlate inversely with the degree of danger under certain conditions. Roof talk and machinery noise recordings obtained during this study were used for subjective tests of ear protectors in a simulated coal mine noise environment. These tests required a detailed interpretation of roof talk and yielded results with high statistical power. Results of these tests showed that the use of personal ear protectors in high noise levels does not degrade a miner's ability to discriminate speech and roof talk. A training course was developed to encourage coal miners to pro-tect their hearing by proper use of personal hearing protectors.

Jan 1, 1973

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By A. R. Taylor

In recent years, thermodynamic data have been used to a greater degree than ever by the chemical and metallurgical engineer as a means of predicting and controlling chemical reactions. To satisfy the spiraling demand for basic physical data needed for the calculations, the Bureau of Mines is studying the heat capacities of a variety of chemical compounds at high and low temperatures. This paper is one of a series presenting such data. The heat capacities of two alkaline earth compounds, strontium bromide and strontium nitrate, were measured in a temperature range of 60° to 300° K. in an adiabatic calorimeter and at temperatures of 300° to about 1,200° K. in a Bunsen ice calorimeter. The construction and operation of the calorimeters are discussed in other reports.3 4 The heat-capacity data presented in this report were extrapolated to 0° K., and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated and tabulated at even 10-degree intervals. The enthalpy data were fitted with algebraic equations by applying the method of least squares; calculations a£ heat-capacity values, entropy, enthalpy function, and free-energy function were made at even 50-degree intervals. The heat and entropy of fusion of strontium bromide were calculated from the enthalpy measurements.

Jan 1, 1962

By Thomas J. Peters

In 1979 and 1980, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 15,600 acre (6,310 ha) Freel Peak RARE II area (No. 5271) in the Lake Tahoe Management Unit. This study by the Bureau of Mines indicates that potential for economic mineral resources in the area is slight. The only mineralized structures in the area consists of two quartz veins. One quartz vein, at the Mountain Top Mine (fig. 1), located by Fred Denner in 1932, is estimated to contain 2,000 tons (1,800 t) of silver and copper-bearing resources. Chip samples from the vein averaged 0.61 oz silver per ton (20.91 g/t), and 1.59 percent copper. The narrow vein is not economically mineable. The other quartz vein is poorly exposed and contains traces of molybdenum. A second reported molybdenum occurrence could not be substantiated.

Jan 1, 1982

By Met M, Worner H. K

In pursuance of the investigation into the influence of various elements on the properties of lead during the past year, the effect of several elements on the creep rate of commercially pure lead has been investigated; a standard initial stress of 500 lb. per sq. in. having been adopted for comparison purposes. Other work which has been carried out indicates that the relative results of creep tests may be altered by varying the applied stress, but this aspect of the problem will need to await further investigations for itscomplete elucidation. The results obtained with dilute tellurium alloys are considered sufficiently interesting, and in some respects are so extraordinary, as to warrant publicatiorr at this stage.n must be realised however that, since the results obtained appear to be at variance with those said to have been obtained in practice and those previously published, the present investigation can only be considered as a contribution to our knowledge of the general problem.Consequently it is not considered advisable or necessary to offer detailed explanation of the results given. In fact, some features of the tests about to be described will need further investigation before an adequate explanation is possible.

Jan 1, 1936

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

Upgrading of Superfine Low-Grade Haematite Ores by Reverse Floatation Direct Reduction Low Intensity Magnetic Separation Process

Sep 13, 2010

By Clark F. Grain

These investigations were undertaken as part of the Bureau of Mines program for the development and evaluation of high temperature nonmetallic materials. This report consists of thermal expansion and phase inversion measurements by high-temperature X-ray diffractometry on the principal oxides of beryllium (BeO), calcium (CaO), titanium (TiO2 ), zirconium (ZrO2 ), hafnium (HfO2), and thorium (ThO2); all were high-purity commercially available oxides. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures. Expansion was determined parallel to each major crystallographic axis for the anisotropic oxides: BeO, TOi2, ZrC2, and HfO2. Combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C. and approximately 2 percent at 1,000° C. No hysteresis in the expansion curves was noted between heating and cooling cycles. The Bureau's values were compared with published expansion measurements obtained by X-ray diffraction, dilatometric, interferometric, and telemicroscopic techniques. For anisotropic oxides, average linear expansion values were calculated from the volume expansion.

Jan 1, 1962