Search Documents

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By Laurance L. Oden

The Bureau of Mines is developing nickel catalysts for converting synthesis gas derived from coal to synthetic natural gas. The present report describes the relationship between the composition of aluminum-nickel alloys in the composition range NiAl3 to Ni2Al3 equilibrated at 840° C and the properties of catalysts obtained from them. Methanation activity was determined in the temperature range of 300° to 360° C in a flowing gas stream containing 1 pct CO, 8 pct H2, and the remainder He. One part per million of H2S was added to the gas stream at 400° C to evaluate the susceptibility of catalysts to sulfur poisoning. The total surface area was measured by the adsorption of nitrogen at liquid nitrogen temperature, and the active surface area was measured by the adsorption of hydrogen at room temperature. Total surface area and active surface area were found to increase with increasing proportion of aluminum-saturated Ni2Al3 in the precursor alloy, but methanation activity and resistance to poisoning by H2S were nearly constant. However, the methanation activity of the catalyst prepared from stoichiometric Ni2Al3 was less than half that of the other catalysts.

Jan 1, 1978

The sequences in alteration and mineralisation from five copper-gold porphyry systems (Taysan and Didipio, Philippines; Horse-Ivaal and Wafi River, PNG; and Goonumbla, Australia) and one gold-copper skarn system (Browns Creek, Australia) are documented in this paper. Alteration and mineralisation in all these systems reflect a common evolution from crystallisation of melts emplaced at shallow crustal levels (zoned potassic -> propylitic alteration), followed by exsolution of volatile-rich fluids from these melts (porphyry quartz ¦K-feldspar/biotite veins and local high temperature advanced argillic alteration), to a progressive cooling of the intrusion which results in associated retrograde alteration. Copper-gold mineralisation in all cases is almost exclusively restricted to the cooler retrograde events. The recognition of the temporal and spatial zonations in alteration and mineralisation in gold-copper porphyry systems has significant relevance in the interpretation of geophysical signatures, overprinting alteration, vein sequences and structural controls, and can lead to more focused and potentially more cost-effective exploration.

Jan 1, 1999

By Jian Li

Developing the Generation IV nuclear reactor is an international collaborative effort. One of the most promising Gen IV nuclear reactor designs is the supercritical water (SCW) concept, in which the water coolant runs at about 625 oC at the outlet. Under this temperature and high pressure condition, the cooling water is at supercritical state, which poses significant demand for both in-core and out of core materials. High-temperature mechanical properties, corrosion resistance and radiation damage are some of the key challenges. At present, no single commercial material can meet all the requirements of the severe SCWR conditions. Corrosion experiments per-formed under SCW condition yield various kind of corrosion modes, some are very challenging to characterize using conventional techniques. A combination of various advanced characterization techniques proofed to be essential to understand the root cause of materials? degradation.

Jan 1, 2010

By Arthur M. Hartstein

The Federal Bureau of Mines, under a contract with Ultrasystems, Inc., investigated the thermal oxidative degradation characteristics of conveyor belts used in underground mines. This included the determination of smoke evolution, glow characteristics, char yields, and the identification and quantification of all volatile decomposition products in the form of gram of specific product formed per gram of belt sample tested. In addition to these investigations, degradation studies were conducted on some pure ingredients used in conveyor-belt formulations. Three basic classes of belts were investigated: neoprene, polyvinyl chloride, and styrene-butadiene rubber compositions. The studies indicate that styrene-butadiene-based belts exhibit good flame resistance and are the least hazardous in regard to overall formation of toxic decomposition products. Under this program, thermogravimetric analysis was definitely established as a method of material differentiation.

Jan 1, 1976

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to 5-ton pieces, a 150-ton batch-type retort was designed and constructed at the Bureau of Mines Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11 ½ feet inside diameter, and is supported in a 95-foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, was used as the test shale. To date, 11 runs have been completed, and the results of the last 10 of these are reported. The effects of oxygen content of the retorting gas and the superficial gas velocity of the retorting gas on oil recovery from a column of mine-run oil shale were studied. In one run, the average particle size of the shale was substantially increased to determine its effect on oil yield. Oil recoveries ranged from a low of 39.3 to a high of 65.8 volume-percent of Fischer assay.

Jan 1, 1974

By Peter Voulgaris, Allan Haines, Diane Walker, Ian de Bruyn

The Oyu Tolgoi porphyry gold and copper project is located in the south Gobi region of Mongolia. The Ivanhoe Mines project has the potential to become a long-life copper and gold producer that could rank among the largest in the world. There are five deposits which cover a strike length in excess of 6.5 km, from south to north they are named South Oyu, Southwest Oyu, Central Oyu, Hugo South and Hugo North. The first three, collectively known as the Southern Oyu deposits, are planned to be mined by open pits, whilst extraction of the deeper Hugo deposits is planned using block caving techniques. The pits will have diameters of approximately 1000m and a maximum depth of 550m. The geological environment consists of a sequence of porphyritic augite basalt, dacitic tuffs and sedimentary rocks that have been intruded by several generations of porphyritic quartz monzodiorite and numerous post mineralization dykes. Several major faults cut through the southern deposits juxtaposing the relative position of the stratigraphy. The geotechnical investigation for the Oyu Tolgoi Open Pits was conducted in three distinct phases of increasing complexity: scoping study; advanced scoping study and feasibility study. Each phase consisted of data collection, interpretation and analysis designed to progressively develop 3D geotechnical domaining for the empirical, structural and numerical evaluations. The development of the geotechnical design parameters for these green fields open pits posed many technical challenges, brought about by the conditions associated with a lithologically and structurally complex environment. The design work focused on the optimization of the pit geometry to conform to equipment selection and blasting characteristics. Limiting bench stack heights were derived from the influence of major structures. The overall slope angles in each pit sector were developed around the requirement for haulage ramps and geotechnical berms. This paper describes each of these aspects and the methodology used to address the integration of the geotechnical characteristics with the mining environment.

Jan 1, 2006

By Guy Chevalier

The QCM Mount-Wright mine and concentrator complex produces about 14 M tonnes of iron concentrate annually. Approximately 9.5 M tonnes of this concentrate are used to produce iron ore pellets at four different silica grades: Three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the realization of two projects where the acquisition of new process equipment led to an improved pellet plant iron recovery, a better flexibility and to lower operating costs as well as to the production of fine iron ore concentrate from the Port-Cartier tailings pond. Typical 4.8 % SiO2 concentrate is processed to achieve required pellet silica content. This is obtained with the aid of hindered settlers or hydraulic classifiers, screens, whims and, lately, spirals. The increasing demand for low silica iron ore products resulted in a greater need for upgrading. The Pellet Plant upgrading capacity being limited, more and more iron units were lost. Base on test works results and economic evaluations, QCM engineers figured out a way to increase efficiently their upgrading plant capacity and go back in the pond gather what has been lost in recent years of operation.

May 1, 2007

[ ]

Jan 1, 1975

By Kenneth M. Maas

The Bureau of Mines inventoried all lands in Alaska to determine the availability of land for oil, gas, and coal leasing. Acreage for onshore oil, gas, and coal basins was digitized as was land ownership data. Regulatory policy concerning oil, gas, and coal leasing for various government agencies and private concerns was determined. Oil and gas basins underlie 79.4 million acres of Alaska's 378 million acre landbase. Federal agencies manage 44 million of these acres. The Bureau of Land Management is the lead agency for most oil and gas leasing on Federal lands. Lands have to be specifically opened for oil and gas leasing to be available. The state of Alaska manages 21.1 million acres underlain by these basins. More than 80 percent of this acreage is available for resource development. Native corporations manage the remaining 14.3 million acres of favorable oil and gas land. Coal basins underlie nearly 51 million acres of Alaska. Of this land, 26.4 million acres are under Federal jurisdiction. The state manages 17.3 million acres of land underlain by coal basins. Nearly 7.3 million acres of favorable coal lands are managed by Native corporations.

Jan 1, 1991

By Abdurrahman Cetinbas

The periphery of longwall panels in the Pocahontas No.3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray system.

Jan 1, 1974

By Marc Arl

Failures of the face and roof above longwall shields have caused days and sometimes weeks of lost production. A common recovery method for these failures has been to pump light weight cementitious grout into the roof and face cavity to stabilize the area This approach while effective is very time consuming and costly. Mines in several coal producing nations have over the past few years been applying phenolic foam grouts in these situations in lieu of cementitious materials. Phenolic foam is a two-component injection product intended for cavity filling, air and gas sealing and the consolidation of highly fractured strata. The properties of phenolic foam; rapid application, quick setting, high expansion rate, high compressive strength and excellent anti-static properties, produce a fast, safe and cost effective cavity filing solution. The product is also classified as fire resistant and so is also suitable for sealing off underground heatings and for aiding fire fighting operations in deep mines. This paper will discuss the application and use of phenolic foam in various underground coal mines in the world over the past few years.

Jan 1, 2005

By Askari-Nasab, D. Checkel, K. Awuah-Offei

Life Cycle Assessment (LCA) is an emerging environmental management tool for examining environmental impacts from cradle to grave. In this paper, LCA is used to evaluate the acidification potential (AP) and global warming potential (GWP) of belt conveyors and truck haulage systems in a surface gold mine using the ISO 14040 standards. The results show that, for AP, the truck system has 32 kg of equivalent SO2 per functional unit, compared to 8 kg for the conveyor system. However, for GWP, the conveyor has 2,820 kg of equivalent CO2 per functional unit, compared to 648 kg for the truck option.

Jan 1, 2009