Search Documents

By Cláudio S. S. Pinto

Em face do agravamento da situação da energia elétrica no Brasil, com disponibilidade cada vez mais restrita e custo cada vez maior, torna-se urgente reduzir o seu consumo onde possível. Ventiladores centrífugos de processo de médio e grande porte são grandes consumidores de energia elétrica e podem ter um elevado potencial para a redução do seu consumo. Este texto mostra como identificar a possibilidade de economizar o uso da energia elétrica em um determinado ventilador e que modificações ele necessita para cumprir este objetivo.

Sep 25, 2017

By Armando Vazquez

When water enters the EAF, some chemically dissociates to H2 while some remains as H2O vapor. Depending on operating conditions the levels of combustible gases (CO and H2) and H2O are continually changing throughout the course of any individual heat and on a heat-toheat basis. The EFSOP® system has been implemented in more than 80 installations as a powerful tool to reduce furnace operation costs but with water detection technology the off gas technology is a valuable solution to improve safety. This paper describes the latest results when using Tenova Goodfellow’s new standalone water detection technology that for the first time provides real-time analysis of both H2O vapor and H2 from start-to-end of a heat. It involves a newly designed water cooled probe and heated line that eliminates condensation during off-gas sampling and an analyzer equipped with a proprietary system for analyzing both H2O vapor and H2.

Jul 30, 2018

By José Divo Bressan

Present work examines material surface damage by cavitation erosion of metals or the wear phenomenon from water bubbles collapse near the metallic surface. Material surface damage by cavitation erosion is due to wear mechanisms of liquid micro-jets impingement and shock waves. Experimental cavitation in tap water was investigated, using the proposed new design of compact rotating disk equipment. In this device, a rotating disk with cavitation inducers and specimens fixed on it ran in tap water to provide cavitating flow at constant high speed of 47.9 m/s similar to service conditions in pumps and propellers. Two types of cavitation inducers in the rotating disk were investigated: through-holes and pins. Carburized cast iron, aluminum, brass and bronze specimens were tested in this device. The cavitation damage mechanisms were observed by scanning electron microscope. Surface damage in the specimens was measured by mass loss and plotted in graphs of mass loss versus running time. After 25 hours testing, the specimens surface showed pitting formation and mass loss. All specimens presented surface damage: pit diameter size was about 100 or 150 to 300 micron. In aluminum specimen, damages by burned pit formation and plastic deformation could be seen, however, the mass loss was lower than the expected, possibly due to alumina film formation. Present equipment had quite good test reproducibility when compared with results from literature.

Jul 31, 2018

By José Aparecido Pereira

The innovative methodology developed by the author allows the elaboration of an Angle Roll Pass Design based on the practical observations of the rolling process and applies mathematical criteria, using the Ekelund´s formula supported by Advanced Excel tools (Reach Goal, PROCV-PROCH, Macros) and AutoCad. The first step is the definition of the number of stands, roll dimensions, gear boxes reduction, initial stock, average reductions, spread factors, finishing speed and type of grooves. For each pass are calculated: bite angle, spread, section reduction, lost and gain of temperature, separating force, speed, torque and motor power. After these calculations and checking of the parameters, the program calculates the dimensions of the passes transforming the flat passes into shaped ones. With these dimensions it is possible to draw the grooves using AutoCad and check section reductions. This methodology was already used for the development of a new project and also to check the parameters of existing ones, with comparison of the results and has shown to be reliable in real and tested projects. It is an innovative process that is not available in known literature.

Oct 1, 2019

By Andre Luiz Nunis da Silva

Didímio metálico foi obtido no Instituto de Pesquisas Tecnológicas do Estado de São Paulo, a partir do óxido de didímio, o qual foi produzido pela extração por solventes de óxidos de terras raras do concentrado obtido na mina de nióbio da Companhia Brasileira de Metalurgia e Mineração - CBMM. Foram investigadas duas rotas tecnológicas, metalotérmica e redução eletroquímica, ambas ocorrendo em sais fundidos. Foi possível produzir didímio com um mínimo de 99 % de pureza por ambas as rotas, mas a rota metalotérmica demanda uma etapa de processamento adicional para remover impurezas e agentes redutores.

Oct 30, 2017

By Sidmar Aparecido Ceresani

O presente estudo tem como objetivo demonstrar a cinética de recristalização e o amolecimento da liga C272000 processada na laminação a frio com uma deformação de 75%. Para determinar o modelo cinético Johnson, Mehl e Kolmogorov (JMAK) foi adotado a temperatura de 450° entre 5min. a 50min. Restaurando totalmente a microestrutura deformada plasticamente sendo progressiva a elevação do tempo e da temperatura. A caracterização microestrutural das amostras foi utilizado microscopia óptica e metalografia. Conclui-se que o modelo JMAK satisfaz a forma de nucleação da recristalização da liga C272000.

Oct 30, 2017

By Lucas Coelho da Silva

Este trabalho tem a pretensão de problematizar a influência da corrosão, sobretudo nos trocadores de calor, e trazer a importância de um estudo prévio detalhado, ressaltando como o desempenho deste equipamento está relacionado ao material utilizado e como esse estudo pode nos abster de grandes dispêndios. Através de ensaios eletroquímicos vamos estudar o comportamento do aço Super Duplex UNS S32750 em diferentes meios corrosivos, com o intuito de avaliar se o nível de corrosão do material é adequado para as condições severas de operação impostas a um permutador de calor.

Aug 16, 2017

By João Paulo Ferreira Santos

Neste trabalho, foram obtidas estruturas compósitas constituídas por camadas alternadas de epóxi com mantas de nanofibras de nylon 6. As nanofibras foram produzidas pela técnica de eletrofiação. O comportamento mecânico destas estruturas sob tração e sob impacto pendular IZOD foram estudados. A incorporação das nanofibras na matriz epoxídica permitiu aumentos no módulo de elasticidade (6%), na resistência a tração (7%) e na energia de impacto (2%), ou seja, houveram ganhos de resistência mecânica sem sacrificar a resistência ao impacto, ao contrário do que ocorre na quase totalidade dos micro ou macromateriais modificadores do epóxi.

Aug 8, 2018

By Antonio Regio Avancini

Nos últimos anos Vitória vem sendo fortemente afetada por chuvas torrenciais em um curto período de tempo. Para garantir a segurança dos trabalhadores e equipamentos como também reestabelecer as condições normais de trabalho num menor intervalo de tempo, foi necessário rever e criar alguns procedimentos com o intuito de mitigar o efeito das chuvas. Os procedimentos são voltados principalmente a melhor manutenção das galerias de escoamento de água, melhorias no sistema de drenagem dos pátios, redução de altura das pilhas de matérias-primas, melhorias nos procedimentos de recuperação das matérias-primas dos pátios.

Aug 16, 2017

By Rodolfo da Silva Teixeira

As ligas de NiTi ricas em Ni tendem a exibir o efeito superelástico a temperatura ambiente. As amostras em estudo foram submetidas a tratamento térmico e mecânico a fim de avaliar o comportamento superelástico destas. Foram realizados ensaios a temperatura ambiente difração de Raios-X (DRX) para identificar as fases presentes e avaliaram-se as propriedades mecânicas via ensaios de ultramicrodureza instrumentada com pré-ciclagem térmica (aquecimento e resfriamento). Os resultados de ultramicrodureza instrumentada exibiram bons indicativos quanto ao uso prévio desta ferramenta para análises do comportamento superelástico destas ligas.

Oct 30, 2017

By Dong Maolin

A great amount of high temperature off-gas, whose maximum temperature is up to 2100?, is generated during the smelting process of electric arc furnace (EAF). The dust content, which is mainly iron oxide, of the off-gas is high and worthy of industrial recovery. The heat carried by the high temperature off-gas with dust is about 11% of the total energy input of EAF, and some even is as high as 20%. The high-temperature off-gas not only takes away a lot of heat but also places a huge burden to de-dusting system of EAF. It not only reduces the iron oxide dust recovery ratio, but also causes serious pollution problems. With the development of the iron and steel industry, the proportion of molten iron for EAF gradually increases, and even more than 30% in some cases. The increase of molten iron causes increases in the amount of EAF off-gas and heat waste. As a result the problem of dust removal is worsening [1-2]. How to sufficiently recover the sensible heat of the high temperature off-gas, create conditions for efficient dust removal, thus reduce operating costs of dust removal system and the production costs is a problem which EAF steel making companies must pay attention to.

Oct 30, 2017

By Daniela Oliveira Mota Guimarães

As inclusões de sulfeto de ferro são indesejáveis no aço, pois são responsáveis por causar o fenômeno de fragilização a quente. A relação entre manganês e enxofre se torna de plena importância para o entendimento desse fenômeno. O presente trabalho teve como objetivo indicar a relação entre Manganês (Mn) e Enxofre(S) mais adequada para a não ocorrência deste fenômeno, e explicar a influência dessa relação nas propriedades dos aços C-Mn. Estudou-se um aço C-Mn com a relação Mn/S 50% menor do que a relação visada na Companhia Siderúrgica Nacional(CSN).

Aug 16, 2017

By Gilmar Ferreira Bataglia

The possibility of parameterization of hot tensile data together with creep data is investigated, for Aluminium Alloy 7475-T7351. This study represents part of a broader research program aiming at the validation of a methodology recently proposed for analyzing both kinds of data together, considering different metallic materials. The results presented in Part 1 of this work, were analyzed according to 4 traditional methods of the literature for parameterization of creep data, namely: Larson-Miller, Orr-Sherby-Dorn, Manson-Succop and Manson-Hafferd. The compatibility of the hot tensile test results with those of creep is remarkably good, indicating the possibility of using both kind of data together also in extrapolation schemes. The criterion proposed for equivalence between hot tensile and creep data is verified to work well also for this kind of material, under the present experimental conditions.

Aug 8, 2018

By Adriano Francisco dos Santos

Dentre as diversas atividades executadas na área de Utilidades de uma empresa, o processo de clarificação e potabilização da água é de suma importância para a manutenção dos processos e das pessoas que ali trabalham. O presente trabalho visa mostrar a preocupação da Área de Energia com os funcionários, colaboradores e comunidade, no que se diz respeito aos riscos a saúde e segurança na utilização do cloro gasoso no processo de clarificação e potabilização da água e as atitudes tomadas para eliminação desse risco, durante o processo de substituição do cloro gasoso pela tecnologia Oxamine®.

Jul 31, 2018

By Fernando Henrique Gomes de Souza

Techniques which use a spring to supply the bias force to actuator are well adopted since they are inexpensive and simple to construct. In this work it was design an actuator concept using bias-type device technique, which comprises two coils that mutually push against each other to supply the stroke. For the coils springs, it was used a wire of NiTi shape memory alloys (SMA) and a wire of 400 grade maraging steel as construction materials.

Aug 8, 2018

By Helênio Resende Silva Júnior

Arcelor Mittal Asturias coking plant at Gijon works, Spain, is undergoing a complete modernization of the whole coke making complex. In this context, Gijon has to be considered a brownfield project, where Paul Wurth has been awarded with the engineering, supply of key equipment as well as erection and commissioning supervision services for the rebuild of two coke oven batteries the modernization of the adjacent by-product and relevant waste water treatment plants. Main objective of this paper is to present the technological improvements introduced by Paul Wurth in the rebuild of a modern plant focusing on fulfilling all the recent environmental regulations.

Oct 30, 2017

By Johanna Alegría-Ortega

Cr/CrN bilayer coating was deposited on AISI 440C by Cathodic Arc. The composition and structure of the Cr/CrN coating were investigated by scanning Electron Microscope, X-Ray Diffraction and X-ray Photoelectron Spectroscopy. The results show that crystal structure obtained was CrN phase with preferred [220] orientation. The hardness and adhesion of coating also were studied. The evaluation of erosion-corrosion (EC) on 440C bare and coated with Cr/CrN was performed by carrying out wear tests using a slurry jet with impingement angle 90° at 4 and 8 m/s. Corrosion, erosion and synergism wear rate were evaluated following the procedure described in ASTM G-119-09. This study presents that the synergism wear rate exceeds 40% of the total mass loss for coating and 60% of mass loss for the 440C, being the most aggressive wear component. The increase in impact velocity generated a rise in mass loss for both 440C bare and coated. The Cr/CrN coating offers better corrosion and erosion–corrosion resistance under all the tested conditions.

Aug 8, 2018

By Andrea Zanon

Recently steel manufacturers have significantly focused their attention on safety and working conditions thanks to new labour laws, comprehensive operators’ knowledge and increased company social responsibility. Even with a reduced budget, investments on safety are now widely approved. Mill constructors aim at developing upgraded solutions to comply with these new requirements. In some cases mill constructors can even anticipate customers’ requests and consequently put into the market innovative solutions. In this text we will analyze some advanced solutions developed by Danieli & C. Officine Meccaniche Spa - the leading company in long-product rolling mills - aimed at improving working conditions on wire-rod block settings. In particular, we will focus on rolling guides installed on fast-finishing blocks and on servo-assisted device for rolling rings changing. In fact, this equipment has shown effective benefits on our test plants and has mainly cut out the tendency of the personnel to be absent due to backache. This paper will first present standard working conditions, will then introduce the newest equipment developed by Danieli & C. Officine Meccaniche Spa, will analyze its operation and finally will describe in detail the benefits that can be reached with its use.

Jul 30, 2018

By Jan Lückhoff

The introduction of the EAF Quantum furnace by Primetals Technologies represents an important milestone in the field of electric steelmaking during the last 15 years. In this process the latent and chemical heat of the off-gas generated during a melting process in an EAF is used to pre-heat scrap in an integrated shaft prior the melting of the scrap in the vessel. Combining proven own technologies, Primetals EAF Quantum enables nearly continuous process, cutting down idle times and enhancing availability for production. The essential benefits will be shown in this Paper.

Aug 16, 2017

By Antonio Esposito

Saving energy and reducing resource’s consumption by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and designed to minimize the energy requirements and to maximize the recovery of materials and energy. The sensible heat in coke pushed out of oven chamber takes up 35 ÷ 40 % of energy consumption of coke oven. Usually the coke thermal energy is lost during traditional coke wet quenching, necessary to reduce the coke temperature for the storage and the following use in steelmaking processes. BPSL CDQ project is a sample how Paul Wurth’s technology allows to reach the energy saving goal and offers an alternative to traditional quenching. With the adoption of Coke Dry Quenching process, a considerable amount of this sensible heat in the coke can be recovered by producing steam; its production depends on various parameters, some of them battery related (Volatile Matters in red hot coke) and others CDQ system related (coke burning losses, superheated steam characteristics (i.e. P,T)), greatly depending also on boiler efficiency (heat exchange efficiency, insulation of the boiler itself, air leakage, etc.). The adoption of CDQ process reduces also the water consumptions in comparison with traditional quenching.

Aug 16, 2017