Search Documents

By F. M. Stewart, F. H. Callaway, R. E. Gladfelter

In this paper oil initially in place is calculated by the various methods commonly used for analysis of water drive fields using data available as time progresses. Rate and pressure are predicted by means of the same methods using data available at the end of two years' history. These predictions are then compared with subsequent performance permitting an evaluation of the methods, which are Modified Schilthuis, Simplified Hurst, van Everdingen et al (1952), and the Electric Analyzer. INTRODUCTION Several variations of the material balance equation, differing in the term used to evaluate water influx, are in common use for estimating oil in place, predicting rate and volume of water influx, and forecasting producing rates and reservoir pressure in water drive reservoirs. The electric analyzer with an electrical network set up to simulate the oil reservoir and aquifer and their contained fluids may be used for the same purpose. Examples of the application of one or another of these methods have appeared in the literature. The accuracy and reliability of the material balance for calculating oil in place have been covered.' However, there have been few articles in which more than one method has been applied to an actual field allowing a comparison. It is felt that a field example, simple in nature, where the Modified Schilthuis, Simplified Hurst, van Everdingen et al (1952), and the Electric Analyzer have been applied would be of benefit in providing an evaluation of these methods as to their comparative usefulness and reliability in calculating initial oil in place and predicting performance. The Torchlight Tensleep reservoir is a small field in a large aquifer. The reservoir oil is greatly under-saturated, having a bubble point of only 55 psi and 2 cu ft/bbl of gas in solution. Changes in the reservoir volume factor in the range of pressures encountered are small, meaning little error in converting production to reservoir conditions. The pressure has declined from 1,618 psi initially to 137 psi during the first four and one-half years. Water production has been negligible. For Torchlight, the material balance equation as discussed later is considerably simplified by the omission of terms having to do with free gas. Thus with simpler equations, less variables to consider, the large pressure drop, the absence of a gas phase, and rapid pressure-rate adjustments, which mean an unusual amount of history in a short time, the reservoir appears suitable for comparing the methods listed above. GENERAL INFORMATION ON THE FIELD The Torchlight field is located on the eastern side of the Big Horn Basin, Big Horn County, Wyo., approximately 3 miles east of the town of Basin. The Tensleep reservoir was discovered in September, 1947. It lies at a depth of about 3,000 ft and produces oil of 35" API gravity. A total of five wells have been completed in the Tensleep, but only four are now producing. The reservoir is well defined in areal extent in that a total of 13 wells have penetrated the Ten-

Jan 1, 1955

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By J. B. Hess, R. L. Dietrich

In the mechanical twinning of magnesium on the {1012} planes the crystal-lographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only undef tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [1120] fibers,' the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to ( 1or2 ) twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or un-twinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler's lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig I is the pattern of an uncompressed specimen of AZ3I alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on (1072 planes produced an 86" reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o'clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o'clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1949

By Roscoe E. Bell

BETWEEN 1945 and 1948 the author made studies of the western phosphate industry and its potentialities. These included an appraisal of the opportunities for western development of the industry, studies of production costs, of market potentials, of transportation economics, and of industry location. This paper will be directed toward pointing up the factors which have an important bearing on the establishment of fertilizer plants in the western area. Industry Location Factors: There are, of course, an infinite number of possible organizational setups which might require consideration. However, the phosphate industry is simple enough so that studies of the most probable alternatives can be made conveniently. The salient factors which require special consideration in such a study are: (I) the location of the raw materials, (2) the location, size, and character of the present and potential markets, (3) the location of energy sources and materials required for fertilizer processing, (4) the location and capacity of present manufacturing facilities, (5) the cost of assembling the materials and energy needed in manufacturing, and (6) the cost of distributing the manufactured product. Raw Material Supplies: Rock phosphate is the raw material for the manufacturing of phosphate fertilizer. In the United States the important known deposits of this material are located in three general areas (fig. 1). The western deposits, comprising about 60 pct of the nation's supply, are in the four-state area—Idaho, Wyoming, Utah, and Montana. The Florida deposits comprise roughly 38 pct of the national supply. The Tennessee deposits, comprising about 2 pct of the national supply, have been the most important source until recent years. The western deposits, which are virtually undeveloped, have not been used to any extent to meet the nation's need for phosphate rock and phosphate fertilizer. Fertilizer Markets: The large national markets for fertilizer are in the midwestern and eastern United States (fig. 2). The principal far-western markets are along the Pacific Coast, especially in California. Until recent years the western markets have been extremely limited, whereas the markets in the eastern United States have long been established and manufacturing facilities have been provided to meet these needs (fig. 3). In recent years the western markets have expanded very rapidly, continuing to grow throughout the war years and postwar period at a similar rate. The question always arises as to whether this is a temporary war-swollen market which will shrink back to its original size as soon as the present agricultural price levels drop. In order to answer this question consideration must be given to the character of the market (fig. 4). I have considered seventeen western and midwestern states in the western market area where transportation costs from the western deposits are equal to or lower than those from Florida. They include all states west of a line drawn through Chicago, Kansas City and the western boundary of New Mexico. In the mewar period this was a small market totaling only 37,000 tons of P,O, annually. The 1946 total for this same area was approximately 200,000 tons. Considerably more fertilizer would have been used in 1946 had adequate supplies been available. Estimates of future markets are difficult to make, but we do have some indices that are useful. The

Jan 1, 1951

By C. B. Post, D. G. Schoffstall

A determinatioil of the hydrogen content of molten steel by means of the Vacuum-extraction method, as reported here, consists in first casting a sample of the bath in a bomb, so that the gases evolved during solidification are trapped for analysis. A portion of the cast steel sample is then prepared and heated at a temperature of 600" to 800°C. under high vacuum, and the gaser given off during this vacuum extraction (which are shown to be hydrogen), are collected and measured. Analysis of the gases evolved on solidification and the gases in the solid sample enables an accurate determination of hydrogen in the molten steel. Fig. I shows the bomb and accessories that have been found suitable for trapping the gases evolved on solidification. The bomb is made of scamless steel pipe, approximately 7 in. long by 136 in. i.d., and welded at the bottom. An ordinary pipe cap has a vacuuni-type metal stopcock threaded and brazed in its upper end. This pipe cap fits onto the bomb by means of machined threads. A flange is brazed to the pipe at the point where the cap starts to tighten up, and a rubber gasket is placed between the flange and cap. Heavy vacuum grease is used between the flange and gasket and the gasket and cap. The weight of the complete bomb and it? interval volume is known before the sample is cast. In practice, a sample of about 400 grams of steel is poured into the bomb, the funnel quickly swung out of the way, the bomb cap spun down the threads and tightened against the gasket, and the bomb set in a pail of water to keep the gasket and vacuum grease cool. It is estimated that at least 80 per cent 01 the gases evolved from the liquid sample during solidification are trapped in the bomb."

Jan 1, 1945

By R. L. Rickett, W. C. Leslie, W. D. Lafferty

Notch toughness of 0.10'pct C steels, rimmed or killed, is improved by holding the steel at a temperature just above the Ae,, followed by air cooling. The improvement can be gained without apparent change in gross microstructure or hardness. The limits of the process have been determined and some possible reasons for the observed effects are discussed. The results appear to indicate that the current theories of transition temperature are inadequate. THE effects of gross microstructural variables (ferrite grain size, austenite grain size, type and distribution of carbides) on the notch toughness of mild steels have been the subject of many investigations.'-' The results indicate that increasing ferrite grain size raises the notch-impact transition temperature. The transition temperature also rises with increasing size of pearlite colonies and with increasing prior austenite grain size, but these factors are not independent of ferrite grain size. The effects of gross composition of steels have also received considerable attention. As a result, manganese, nickel, aluminum, and silicon are known to improve the notch toughness of mild steels. The other elements that have been investigated—carbon, nitrogen, boron, copper, chromium, molybdenum, phosphorus, sulfur, titanium, and vanadium—reportedly are either deleterious or have little effect on notch toughness. Despite this large volume of work, it is still not possible to predict the notch toughness of a mild steel from its microstructure and composition, even when these are supplemented by hardness and tensile tests. Steels with equivalent microstructures, but different thermal and/or mechanical histories, can differ in notch toughness. Such factors as type and distribution of precipitates, substructure, local variations in composition, or unrecognized variables, may be important in determining the notch toughness of mild steels. However, quantitative knowledge of the effects produced by these factors is almost completely lacking. In an effort to improve this situation, an investigation was begun to determine the effect of a very fine precipitate on the notch toughness of low-carbon steels. Aluminum nitride was chosen as the precipitate because of its presence in aluminum-killed steels, the ease of control of precipitation, and past

Jan 1, 1961

Discussion of the papers of Benjamin Talbot. E. A. Beck, Emil Gathmann, Sir Robert A. Hadfield, and P. H. Dudley, presented at the New York Meeting, February, 1913, and printed in this Bulletin (No. 76, April, 1913). CHAIRMAN JAMES F. KEMP :-I call upon Prof. Albert Sauveur to open the general discussion on the subject of sound steel ingots. ALBERT SAUVEUR, Cambridge, Mass. :-I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain some very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my Views.

Jan 4, 1913

By Hugh H. Waesche

High quality quartz crystals weighing more than 50 grams are required in several important industrial applications.30,31 Primarily, they are the basic raw material for precision, electronic, frequency control components; this includes oscillators and filters in both radio and telephone services. Quartz crystals are also necessary for optical lenses and prisms in special applications requiring high ultraviolet light-transmission as in spectrographs. Quartz wedges are regular components for petrographic microscopes. The application of crystalline quartz as a transducer* in ultrasonic devices has increased in recent years despite strong competition from barium titanate and magnetostrictive [f] devices. Some quartz is fabricated into delay lines for radar. Man has valued quartz for fabrication of art objects since the dawn of history. The art forms were and are painstakingly carved and polished to form intricate figurines, bowls, statuettes, and the well-known crystal balls. The largest known ball, made of perfect quartz from Burma, is now in the National Museum in Washington. It is 12 7/8 in. in diameter and weighs 106 lb 12 oz. Clear, pure quartz chips and small crystals not meeting the electronic-grade dimensional requirements are known by the Brazilian term lasca. They are used to produce fused quartz having wide application in laboratory equipment, as special glasses, for torsion suspension in scientific instruments, and as a source material for growing large artificial quartz crystals 18,35 Electronic applications far exceed all other uses in importance so any discussion of high-quality quartz crystals must be concerned almost exclusively with those functions. Historical Background Because of their ubiquitous character and natural beauty, quartz crystals have long been of interest and known to man. They have been found among early Egyptian and Chinese art forms and the Sumerians are believed to have fashioned seals, beads, and other jewelry from quartz crystals, perhaps 5,000 years ago. Also, American Indians made arrow heads and fashioned some simple objects of different kinds. The origin of the name quartz, although of Greek derivation, is uncertain. The Greeks appropriately applied their word for frozen water or ice, krustallos, to quartz. The present-day, large-scale practical applications of quartz crystals began in 1880-1881 when Pierre and Jacques Curie reported discovery of the "piezoelectric" effect. They found this effect first in Rochelle salt, a common product of grape-wine refineries, while studying crystal symmetry. Piezoelectricity is that property found in certain crystals, including quartz, whereby electrical charges of equal and opposite sign appear on opposite parts of the crystals when they are stressed. If equal and opposite forces are applied to two opposing prism edges of a single untwinned quartz crystal a positive electrical charge will appear on one edge and a negative charge on the other. The amount of the charges will be directly proportional to the force applied. This property seems to be intimately related to pyroelectricity

Jan 1, 1960

By D. E. Etter, J. E. Selle

The Pu-Ce phase diagram was determined by differential thermal analysis, metallography, and elechm-nricroprobe analysis. The dingram is chararterized by a eutectic with extensive solid solubility in the cubic Phases of both cerium and plutonium. No intermediate phases were found. Cerium is soluble in e plutonium to 16.0 at. pet Ce at 626OC nnd in d plcltoniurn to 23.0 at. pet at 613 "C, decreasing to 17.5 at. pet at room temperature. No solubility in the a, ß, or ? phases was jound, and the mininum cerium required to stabilize 5 plutonium to room temperature is 3.2 at. pet. The maximum solubility of plutonium in 6 cerium is 19.5 at. pet at 721OC, and the maximum soluhility of plutonium in ? cerium is 34.5 at. pet. Invariant points in the system are: a) eutectic at 626oC, L16.5 = E Pu16.0 + y Ce65.5; b) peritectoid at613oC, e Pu13.5 -y Ce65.5- d Pu23.0. AS part of a program aimed at the determination of the phase equilibria in the Pu-Ce-Cu ternary system, preliminary investigations were made of the three binary systems. A survey of the Pu-Ce binary system by differential therma1 analysis indi- cated several areas of disagreement with the published diagram,' primarily in the shape of the liquidus surface. Consequently, a thorough investigation of the system was undertaken, and this report presents the results of the study. EXPERIMENTAL PROCEDURE Three methods of investigation were used: differential thermal analysis (DTA), metallography, and analysis with electron-microprobe X-ray analyzer (EMX). The EMX analysis was particularly useful for the determination of solvus lines. The DTA method was most useful for the determination of the liquidus curves. Metallography complemented both of these techniques. Materials. The cerium metal used for most of this work had a freezing point of 805°C. This material showed 15°C premelting, and was found metallographically to contain some unidentified in~lusions.2 The temperature of premelting is defined as the point at which the DTA curve breaks away from the base line, analogous to a curve obtained from a solid-solution alloy. Several compositions were prepared near the cerium end of the diagram with higher-purity material which had a freezing point of 800°C. etallographic analysis showed this material to be relatively free of inclusions and only 8°C premelting was observed. Major impurities were found by spectrographic

Jan 1, 1964

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to '939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By K. O. Stamm, B. A. Rogers

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By J. B. Hess, R. L. Dietrich

IN the mechanical twinning of magnesium on the {1012} planes the crystallographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only under tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [ 1120] fibers,1 the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to {1012 } twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or untwinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw3,4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler's lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig 1 is the pattern of an uncompressed specimen of AZ31 alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on {1012} planes produced an 86° reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o'clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o'clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1948

By W. A. Wood, W. H. Reimann, K. R. Sargant

A study is made of the microstructural changes produced in armco and pure iron subjected to alternating torsion at amplitudes above and below the knee of the S/N curve. The aim was to identify the basic mechanisms of fatigue and to find why they should give rise to a sharp S/N knee in contrast to the type of S/N curve shown by fcc metals. It is found that the basic structural change above the knee in the iron is a pronounced cell formation in the grains, which determines irregular micro-cracks, and below the knee a dispersion of fine slip that determines a dispersed pore formation in the grains. Comparison of these changes with those in fcc metals similarly tested shows that they do not include an intermediate structural change, a concentrating of slip in narrow bands with associated slip-band cracking, that characterizes the fcc metals and accounts for their different type of S/N curve. RECENT conferences on basic mechanisms of fatigue emphasize that fatigue damage takes many forms: for example, cracking in slip bands (Thompson1), at grain boundaries and inclusions (Hempel'), at precipitation zones in alloys (Han-stock, Forsythe), or at surface notch-peak effects, both hypothetical (Mott, cottrel16) and observed (Wood). Evidently it is not easy to see in this diversity a basic mechanism. At the same time the contributions suggest that some reconciliation may be possible if distinctions are drawn between three phases of the fatigue process: initiation of damage at nuclei, distribution of these nuclei, and the final macroscopic crack system. In initiation, the relevant features appear to be that nuclei may appear early, at least by 1/100th to 1/1000th of the life of a test specimen; that they may do so at many independent centers, appearing according to some observationsa as pores or voids; and that they are not necessarily self-propagating, damage spreading rather by their multiplication. In distribution, the relevant feature appears to be that they form preferentially in zones where the microstructure becomes abnormally strained (as defined more closely below). Now in these two phases the basic fatigue process should be systematic. But, at the same time, the "abnormal strains" in particular set the stage for considerable diversity in the final phase of macroscopic cracking, for where zones of abnormal strain develop will depend on what kind of fatigue deformation is applied and what kind of prior processing the test material has had. On this view it seems desirable to know what in

Jan 1, 1964

By Wheeler P. Davey

In an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. l.) Fig. 2 is a photograph of the end of the punching, showing the hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of radiographing metals. In order to gain some preliminary data, several pieces of 1/2-in. (12.5-mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter I.........................................1/4 in. =6.3 mm 2........................................1/8 in. =3.l mm. 3................................... 1/16 in. = 1.6mm. 4....................................... 1/32 in. = 0.8 mm. 5........................................1/64 in. = 0.4 mm. Exposures were made on Seed X-ray plates at 20 in. (50 cm.) distance with Coolidge tube X-117, operated on Scheidel-Western induction coil with mercury turbine break. The X-ray plate was placed on a sheet of 1/8in. (3.1-mm.) lead. The steel was placed above this and a Iead

Jan 1, 1916

By T. A. Wright

The sampling of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grat) sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases rnuch material can bc sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to incrcase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to makc sorting and grading more difficnlt in turnings, borings, clippings, etc., and conseqllcntly is making sampling of more moment. In tin, lead, alumiinum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosscs, battery lcad, and aluminunl skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or "metallic yield." Coppcr and Icad wastcl, howcvcr, is being sold more and more on actual copper and lead contents bascd on sarrlple and chemical analysts. This paper will be dcvotctl chiefly to the sampling of niaterials suitablc only for refining and recovery of one or more of the metals present. The methods described are often bascd on thc fact that but one, metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect thc final copper result, as the "after-melting" assay can be readily calculated to the "bcfore-nltltingl' basis, but if smelter efficiency continues to increase, so that in tiltie zinc, for instance, may be rccovrred on a paying basis, thc method of sampling dirty brass, for example, will have to bc changed also. As a matter of fact, we may cxpect that improved refining proresses will make possible the partial reeovrry of lcad and tin which are now lost

By T. G. Lovering

Nonparametric statistical tests have practical application to many geological problems because, unlike the standard statistical tests, they do not require assumptions regarding the form of the population frequency distribution. Many of them do not even require that the variable be susceptible to numerical measurement. These tests are useful either 1) for geological data representing population distributions of unknown form, or otherwise not meeting the requirements for standard parametric tests; or 2) for sample attributes that cannot be measured but only ranked in order of relative magnitude. The application of two such tests will be illustrated. The Kolmogorov-Smimov test will be used to test for significant differences in copper distribution in samples of two rock types; the Spearman rank-correlation method will be used to determine whether there is a significant association between intensity of rock alteration and copper content of the rock. Nonparametric tests are, in general, quicker and easier to perform than the corresponding parametric tests, and they may be applied to a greater variety of data. They are not as powerful as the standard tests if used on data to which the latter are applicable, and computer programs utilizing them are not generally available. The use of standard or parametric statistical procedures for the interpretation of measured geological data is familiar to most mining engineers and explora- tion geologists. The computation of product moment correlation coefficients on sample assays for more-than one component is already standard procedure in some company operations, as is the use of Student's F test and Snedecor's F test for the comparison of means and variances of sample groups. The application of these three tests is limited by the prerequisites that the samples must be random, independent representatives of normally distributed populations and that the variables involved must be measurable. If such tests are applied to data which fall short of fulfilling these prerequisites, then the probability level attributed to the computed statistic is invalid and the conclusions based thereon may be erroneous. A number of nonparametric, or distribution free, statistical tests have been developed for use with data which are not amenable to standard parametric procedures. These tests have been widely used in the behavioral sciences such as psychology and sociology for some time, but their application to geologic problems is relatively new. Nonparametric tests may be grouped into two main categories: those which test for significant differences in a single variable by comparing either sample values with a standard value or representative values between two or more groups of samples; and those which test for significant association between pairs of variables in a single group of samples. The versatile chi square test, the Kolmogorov-Smirnov one and two sample tests, the Wilcox matched pairs signed ranks test, the median test, the Mann-Whitney U test and the Cochran Q test are examples of nonparametric tests with demonstrated or potential geological applications that belong in the first category. The contingency coefficient, Spearman rank correlation coefficient, Kendall rank correlation coefficient and the

Jan 1, 1963

By B. A. Rogers, K. O. Stamm

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By P. Chaudhari, Michael B. Bever

The heat of solution at infinite dilution of selenium in bismuth, the heat of mixing of selenium and bismuth, and the limit of solubility of selenium in bis~rzuth have been determined at 573, 623; and 663°K by metal solution calorimetry. The heat of forrrzation of the compound Bi2Se at these temperatures has been determined from the heat effects associated with the precipitation of the compound from a saturated solution oj selenium and bismuth. The published information on the thermodynamic properties of the system Bi-Se is limited. The heat of solution at infinite dilution of selenium in bismuth at 623°K has been measured.' The heat of formation at 273 K1 and room temperature2 and the heat capacity at 80 K3 of the compound Bi2Se3 have been reported. An estimate of the heat of formation of the compound BiSe at room temperature has been published.2 Information on the phase relations in the system Bi-Se is available.' In the investigation reported here the following quantities have been determined at 573", 623", and 663°K: 1) the heat of solution at infinite dilution of selenium in bismuth, 2) the heat of mixing of selenium and bismuth in bismuth-rich solutions, 3) the limit of solubility of selenium in bismuth, and 4) the heat of formation of the compound BizSe. These quantities were determined by the addition of selenium to bismuth-rich solutions in a metal solution calorimeter. The determination of the heat of formation at the tem- perature of the calorimeter bath involved the precipitation of the compound from a saturated solution in the calorimeter. 5,6 This method differs from that commonly used which requires the addition of the compound and of a mechanical mixture of its components and yields the heat of formation at the temperature from which the additions are made (273 K EXPERIMENTAL PROCEDURE AND CALCULATIONS The solution calorimeter has been described in detail.' Pure bismuth (99.999+ pct) was used as the bath at the start of a run. The calorimeter was calibrated with small amounts of bismuth added from 273°K; the differences of the heat contents of bismuth at 273°K and the temperatures of the baths are listed in Table I. After the calibration, additions of hexagonal selenium (99.999+ pct) were made. Loss of selenium by evaporation was negligible. No unusual experimental difficulties were encountered.9 The differences in the heat contents10 of selenium at 273°K and the temperature of the bath, listed in Table I, were subtracted from the measured heat effects to give the "adjusted heat effects". The methods by which the heat of solution at infinite dilution, the

Jan 1, 1968

By F. H. Kihlstedt

THE Larap iron deposits, 125 miles east of Manila, are the biggest high-grade iron deposits in the Philippines, and have in seven years produced nearly 4 million tons of 6o per cent ore. Magnetic surveying followed by churn and diamond drilling cheaply developed a score of million tons. The ore zone is a wedge of metamorphic rocks in fresh, Miocene sediments overlain by agglomerates, which seem to have filled a river valley eroded in the sediments. A mild overthrust of the competent agglomerates crumbled the shale in front. Solutions gradually turned it into more competent hornfels and deposited pyrite, then magnetite and pyrite in the pores. As the temperature rose large bodies of magnetite with some pyrite were deposited by replacement and in open cavities in tensional areas of overthrust shears. At still higher temperature magnetite and calcium-magnesium silicates formed other bodies in similar cavities, and finally the thrust zone was invaded by syenite porphyry, causing high-temperature alteration products. Possibly, as temperature abated, more high-grade ore was deposited. The complicated faulting indicates dynamic, chronological and spatial changes of mineralization rather than zoning in a static system. Noncommercial copper, molybdenum and some gold accompanied the iron mineralization. In the thirties the Philippines gained a justified reputation as a country of considerable mineral wealth. Traces of Chinese workings show that these earliest travelers and traders had in a small way exploited the latent gold resources in the Islands. The Spaniards continued this for centuries, but did not succeed in establishing any steady mining industry. Modern technology was required to get it started. The rapid development in the last decade before the war got its impetus from several financial factors, the return to sugar growers of previously collected taxes, the influx of Spanish capital during the civil war in [ ] Spain, the influx of Chinese capital when the Japanese started their "China incident," and others. Directly or indirectly much of this capital reached the mining industry; in particular, gold mining. Out of the turmoil of an exceptional mining boom emerged a sufficient number of good and well managed gold properties to send the production to a level above that of any single state in the United States at the time. Other ore deposits besides those of gold also received their share, and for a country without any heavy industries at

Jan 1, 1946

By J. B. Murdoch, John G. Jackson

The many mechanical, geological, and economic factors which influence the planning of a directional drilling program are thoroughly discussed and analyzed. It is demonstrated that the planning of a directionally drilled multiple-well artificial island location is a complicated undertaking and that it is imperative that complete planning and engineering analysis be undertaken before the program is started. Complete planning is profitable because all of the factors influencing the directional work are in general interrelated and many time compromises have to be made before a harmonious program results. The engineering control necessary to accomplish a complicated directional drilling program is outlined. Various means by which engineering control can be increased, such as cylinder drilling specifications, are given. A hypothetical example is developed for a complete offshore artificial island of ten wells to demonstrate the more important factors involved in the planning. Included with this example are special charts and tables which make more rapid the drafting of directional drilling proposals and maps. Introduction A petroleum engineer must consider many and varied factors when planning a long range directional drilling program for an offshore or inaccessible location on an oil structure. The basic principles of direc- tional drilling planning and operation must be reconciled with his company's drilling practices, and frequently special concessions to standard drilling and production practices should be made. The field techniques and tools used in directional drilling are well known and widely used, but the deliberate, careful planning of a complete directional program is in the main a recent innovation. This development, plus the increased demand for oil resources and the consequent exploitation of inaccessible structures and offshore locations, has placed this problem before many engineering departments for the first time. Directional drilling programs of a very complex and difficult nature have been successfully carried out in the Mid-Continent and Pacific Coast regions. The planning itself of a directional drilling project, however, has not had the careful analysis it deserves and we can reasonably expect widespread future progress along thesc lines. Data and experience gained in these programs by the directional drilling service companies and the oil producers have been studied with the objective of giving the engineer a better conception of the factors which govern the various steps in planning a series of directional wells. The newest engineering procedures are the result of recent careful analysis of years of directional drilling work accomplished under the supervision of directional drilling service companies working with the oil companies. The purpose of this paper is to illustrate

Jan 1, 1949