Search Documents

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By H. H. Dievendorff, F. W. Hertel

The method of drilling deep wells into the earth for the recovery of oil and gas is beset with many hazards. This is especially true in the Ventura Avenue field, which has the distinction of being the hardest field in California in which to complete a deep well. The hard, shifting and squeezing formations must be penetrated to great depths in the face of tremendous gas pressures. This field presents problems that keep the operators abreast with all of the latest developments in oil-field tools and machinery and in oil-well drilling practices. Equipment must be strong, and adapted to deep-well drilling and the handling of long heavy strings of casing. High-pressure sands require the utrnost care and attention of the operators and no chances can be taken, since a serious blowout may cause the loss of a well that has cost months of labor and expense. Equipment must meet these requirements or be discarded. Although the deepest wells in the world are not in this field, nor hav:. the longest strings of casing been set, nevertheless, the consistency with which deep wells are drilled and long strings of casing are set places the Ventura Avenue field foremost, in this respect, among the oil fields of the world. The V'entura Avenue field dors claim the deepest commercial oil-producing well in the world, in the Shell Co. of California's "Edison" No. 18. This well was drilled 7015 ft. and came in flowing 3280 bhl. of oil per day. This field also claims the deepest average depth of producing wells in that its Ill producing wells average 5676 ft. in depth. Of these 111 producing wells, 50 arc 6000 ft. or deeper, and 16 are 6500 ft. or deeper. Also, of the 111 producing wells 100 arc flowing, and 11 arc pumping wells. This paper is intended to set forth the methods used in the drilling of deep wells with rotary tools and the handling of long heavy strings of casing in the Ventura Avenue field.

Jan 1, 1928

By H. J. Stehli

The first sintering of zinc ores was done at the Bartlesville plant of the National Zinc Co., under the auspices of the late Otto Rissman. Mr. Rissman, who had had a long experience in the treatment of zinc ores, well realized all the difficulties of satisfactorily roasting zinc concentrates, which were becoming finer and dustier as each year went by—thus increasing the difficulties of roasting them in the existing forms of roasters, which were furnaces of the Ropp, Hegeler or similar types. Mr. Rissman's idea of the advantages of sinter was expressed in this way: in a zinc ore dead-roasted in a mechanical furnace there are many particles that are just like an egg; that is, they have a hard and impervious film of fused material on the outside, and in the retorting this completely cuts off access of the reducing gases to the center of the egg until a temperature has been reached at which this shell of the egg can be broken down through fusion. A particle of sintered zinc sulphide, on the contrary, is exactly like a piece of sponge. The moment the retort reaches the temperature at which the reactions can take place, they begin, because the reducing gases have ready access to the interior of the particles by means of the pores of the '" sponge." His faith in the advantages of sinter was amply borne out by the results obtained at the pioneer sintering plant for zinc ores installed by the National Zinc Company. Early Method of Sintering The method of procedure at Bartlesville was to roast the zinc concentrates down to somewhere in the neighborhood of 8 per cent residual sulphide sulphur; to cool these, then to wet them down to the proper moisture and mix them in the mixer of the sintering plant; then to sinter them by means of the heat available from the residual sulphides. The sulphur contents of the roast varied considerably, of course, as it was difficult with the furnaces in use to control the roasting exactly at any point short of dead roast. Hence at times the concentrates were roasted a little too low to sinter readily, and at such times the lack of sulphur was made up by the addition of raw concentrates to the sintering-machine charge in suitable amount.

Jan 1, 1937

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By Ernest Klepetko

A NOTABLE amount of fossil resin exists in many of the bituminous coal beds of Utah. The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8inches. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements. They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics have been found by Inter-Chemical Co. research chemists in the refined resins: [Specific gravity (melted) 1.03 -1. o6 Acid number6-8 Softening point, mercury method 160 -165°C Iodine value (Wijs)140-1.50 Refractive index1.544 Color (Hellige, 25 pct toluol) ...14 Molecular weight, average732 Purity, 99 + pct pure hydrocar Bon] "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility. The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residual coal without excessive size degradation. The late W. D. Green, concentration engineer for Combined Metals Reduction Co., obtained U. S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1947

By M. S. King

In the design of foundations for large structures and of safe mine openings in rock, the results of laboratory and small-scale in-situ tests are often used to predict the behavior of the material as a whole. For reasons of simplicity in these analyses, the rock is usually treated as an ideally elastic, isotropic material. It has been observed, however, that most rocks are neither isotropic nor ideally elastic. This observation is particularly true for rocks subjected to low confining pressures. It is therefore necessary to investigate further the effects of anisotropy and nonlinearity on the mechanical behavior of rocks. When small differences in stress and strain only are involved, the rock may be treated as an elastic material. The elastic constants for such a material subjected to a particular confining pressure can be calculated from the classical theory of elasticity for different degrees of anisotropy. There are two experimental methods by which this can be done: first, from measurements of static stress-strain relationships; second, from elastic wave velocities measured in the rock. The former yields the static elastic constants, and the latter, the dynamic constants. The static constants will be equal in magnitude to the corresponding dynamic constants only if the rock is ideally elastic. Walsh and Brace1 have reviewed theoretical studies of the elasticity of rock considered as a material containing pores and cracks. They re- ported that the presence of sharp, narrow cavities at low confining pressures strongly influences the mechanical properties of a rock. A considerable reduction in magnitude of elastic moduli is associated with the presence of inhomogeneities such as cracks or joints. The elastic properties appear to approach those of the uncracked material in magnitude as the cavities are closed by higher pressures. Walsh and Brace

Jan 1, 1970

By A. K. Knickerbocker

Practically all underground work on the Minnesota iron ranges is done by miners working on a so-called contract wage system. This system, while it has certain advantages over the straight day's pay or company-account method of wage payment, has serious and vital defects. In view of the scarcity and demands of labor, it is important that employers of labor scrutinize their systems of wage payments carefully, not only to save losses and trouble, due to labor disturbances, but also to secure the greatest efficiency of their workmen and reduce their operating costs. It is admitted that an adequate, just, and equitable wage is the prime factor in bringing about these benefits. The wage of labor and its method of application and payment have been, and always will be, the main factors in the unrest and dissatis. faction of labor. Not only does labor want and need an adequate wage, assuming that work is adequately performed, but it wants and is entitled to a just and equitable wage. Labor must have respect for the fairness of the wage and for the fairness of the management in the application of the wage It is conceded that the Minnesota iron miners are now, and have been, in the main paid adequately, but the inherent defects of the so-called contract system prevent any just or equitable application of this wage to the various units of the labor body. The defects of the contract system, with its obvious inequalities, favoritisms, and injustices, are cancers in the brain of labor. Every thinking miner realizes these defects and knows just what they are; the unthinking do not realize the details of the subject, but each month they are forcibly reminded of these defects through the pay envelope. As practiced on the iron ranges, however, the so-called "contract " system is not a contract and the name is a misnomer. No true contractual obligation exists. As usually practised, the contract system involves the setting of a price per foot in development work, or per foot or per car, usually the latter, in slicing or stoping, by the mining captain, and assumes its acceptance, though often under protest, by the men. A price is set for each working place, in which there are usually two men per shift. This price includes labor and supplies, such as explosives, fuse and caps, shovels, carbide, etc., and the men divide the total earnings less the amount expended for supplies. The cost of the supplies charged to the men varies

Jan 1, 1920

By P. H. Dudley

When we see the magnificent passenger-trains of from 8 to 12 coaches, drawn by locomotives weighing from 100 to 110 tons, at speeds of from 50 to 60 miles per hour between terminals, to make a schedule of 45 miles per hour, and freighttrains of from 50 to 75 cars of 60,000 pounds capacity, drawn by one locomotive, it is hard to realize that it lacks a few months of fifteen years since my pioneer 5-inch 80-pound rail for the United States was laid by the New York Central aid Hudson River Railroad Co., in July, 1884, on the Harlem line. Shorter passenger-trains, of from 4 to 5 coaches, are run much faster, notably the Empire State Express, the schedule of which for the 440 miles between New York and Buffalo requires 53.3 miles per hour, calling for a running-speed, for much of the time, of from 65 to 75 miles per hour, while higher speeds are very common. On other railroads laid with my 5 1/8-inch 80-pound rail, speeds of from 60 to 75 miles per hour obtain in daily practice. On many of the important railroads east of the Mississippi high speeds of from 60 to 70 miles per hour are part of the daily service. So many instances of speeds of 90, and even 100, miles per hour have been recorded that they must be considered as likely to occur on important lines, and provision must be made for them in the track. Solid mail-trains of from 6 to 8 cars are run from New York to Chicago, 1000 miles, in twenty-four hours; and, commeneing with the present year, shorter trains are running from Chicago to San Francisco, 2000 miles, in three and one-half days. In the freight-service equally important progress has been

Jan 1, 1900

By H. R. Barnhurst

It would be a difficult matter to trace from the beginning the very few improvements made in the burning of fuels prior to 1860. Donbtless the crossing of the sticks of wood in building a mood fire early appealed to our savage ancestry as a means of expediting its effectiveness for their crude culinary purposes. Stones and andirons came later in assisting the admission of air to the under part of the fuel bed, while beacons and cressets, utilized metal bars as supports for the same purpose. It is probable that Tuba1 Cain owed his success to the use of bellows making possible the use of mixed fuel and charge upon a hearth. With the development of working in cast iron, grate bars came in, and they are still with us doing duty in every household and almost every art where heat is a factor. Little was done beyond these crude methods prior to 1860. With the advancement of knowledge came the fuel-gas producer, a natural child of the retorts employed in supplying illuminating gas. It is only within the last 15 years that the conclusion became general that complicated systems for saving heat would not remedy deli-. ciencies in its primary development, and within that time there has been great advancement in the means of producing initially a fire of high effciency, so that to-day we are moving rapidly toward both high development and high absorption, with the resultant of high efficiencies. In studying the subject of the availability of pulverized coal as a fuel, it may occur to ask, why has this not come up earlier? This, question would be naturally prompted by recalling the fact that Thomas Crompton's English patents upon his methods were issued to him nearly 40 years ago. A conclusive answer to this, however, is that Crompton at that time had very crude facilities for making what was at best a very imperfect pulverization of the coal, arid the expense of preparation mas very great. He does not seem to have been aware of the advantage of a thorough drying of the coal in the

Jan 1, 1914

By J. Bruce Wagner, Roger L. Levin

Lattice-parameter measurements have been carrzed out at room temperature on undoped and on chromium-doped wustite as a function of oxygen concentration. Results may he expressed by for the undoped uustite. These data are in agreement with and extend the work of' Jette and Foole. The present results are consistent with the cation vacancy model. for metal- deficil wuslite, both undopen and doped. SEVERAL investigators have made room-temperature lattice-parameter measurements on wustite as a function of composition. Jette and Foote used these measurements to determine the phase limits of wustite. Willis and Rooksby and Benard have also measured the lattice parameters of wustite at room temperature, but their values of a. vary considerably from those of Jette and Foote. In conjunction with Studies' on the transition from surface-controlled heterogeneous reactions involving CO-C02 oxidation of metals, lattice-parameter measurements on undoped and chromium-doped wiistite have been performed. These studies are especially needed to clarify conflicting data of previous authors, to extend the data to the stability limits of wiistite as determined by Darken and urr,6 which include a larger range of existence than that found by Jette and Foote, and to test by X-ray means the role of chromium as a vacancy producer in wiistite.

Jan 1, 1967

By GILBERT C. DAVIS

ANY thought of Morenci naturally includes its sister town of Clifton, its gateway to the outside world. Clifton, the country seat of Greenlee County, is the terminus of a branch line of the Southern Pacific railroad from Lordsburg, N.M. Carload freight incident to the Morenci operation moves from Clifton over Phelps Dodge?s standard-gauge industrial railroad. Private freight must be hauled by truck. These two communities fell far short of supplying adequate housing for the personnel concerned with the new operations so a new townsite, Stargo, was developed adjacent to Morenci. Here 234 housing units with garages have been built and twenty similar units have been erected near the reduction works.

Jan 1, 1942

By George W. King

The yield strength of a dispersion-hardened W-3.8 vol pct Tho,alloy, in both the recovered and recrys-tallized condition, was investigated and cornpared with that ofrecrystallized pure tungsten over the temperature range of 325" to 2400°C. It is deduced that the Orowan mechanism is obeyed in the recrystallized alloy. In the recovered alloy, a further enhancement of the yield strength results from the retained substructure which is stable up to temperatures in excess of 2700°C. Temperature and strain rate cycling tests were also performed, and the apparent activation energy for the deformation process was derived. This activation energy, - 3 ev, for the recovered and also the recrystallized alloy was about the same as that for re crystallized pure tungsten. However, the activation volume of the recovered alloy, -10-2 cu cm, was about an order of magnitude lower than that of the recrystallized alloy or pure tungsten. This fact accounts for an enhancement oj- the temperature dependence of the yield stress of the recovered alloy. A dislocation velocity exponent of about 4 to 13 was deduced frorn the strain rate cycling tests , which is in good agreement with values reported for tungsten single crystals. VARIOUS theories have been developed to explain the enhanced yield strength of a metal containing a dispersed second phase of small hard particles. These theories are thoroughly reviewed by Kelly and Nicholson.' The theoretical models can be separated into two types. The first type assumes direct interactions between moving dislocations and dispersoids. One of the most widely investigated models for this mechanism is the bowing out of dislocations between the dis-persoids and their subsequent pinching off in order to bypass the obstacles. This is the well-known Orowan mechanism.' The second type is an indirect effect of the dispersion because of its ability to stabilize to high temperatures the substructure introduced by cold working. In this instance, the increment in the yield strength is expected to be inversely proportional to the square root of the subgrain diameter. In the present work, a quantitative study was made of the strengthening effect caused by a thoria dispersion in a recrystallized W-3.8 vol pct Thoz alloy over the temperature range 325" to 2400°C. The results are compared with the increment predicted for the Orowan mechanism based on the calculations by ~shb~.~ In addition, the alloy was tested in the recovered state so that any additional strengthening resulting from the substructure produced during fabrication could be measured. The respective contributions can be separated in this manner, provided that the particle size distribution of the dispersion remains the same in both the work-hardened and the recrystallized state. Particle size distribution measurements showed that this condition was met in the present work. I) EXPERIMENTAL PROCEDURES A) Material Production and Fabrication. The alloy investigated is essentially the same as that reported much earlier by ~effries,~ who also found the strength of tungsten to be improved by the thoria dispersion. The procedure for producing the alloy consisted of mechanically blending a thorium nitrate solution in proper concentration with tungsten oxide (WO3) powder, followed by hydrogen reduction to metal powder. After reduction, the dispersed second phase is present as thoria (Thoz). The pure tungsten powder used for comparison was produced in the same manner except that the thoria doping step was omitted. The powders were consolidated by cold pressing and self-resistance sintering in hydrogen. The resulting ingot had a cross section about 0.6 sq in. and a density about 93 pct of theoretical. The ingot was swaged to 0.174-in.-diam rod at temperatures varying from 1650°C initially to -1200°C near final rod sizes. Two intermediate recrystallization anneals were employed during fabrication. Analysis of the swaged rods is reported in Table I. B) Electron Microscopy Techniques. Carbon extraction rrPxcas prepared by a technique reported by ~00' were used to quantitatively evaluate the thoria particle size and distribution. Electron nlicrographs of extraction replicas were taken at 20,000 times but were then enlarged two to three times in printing. The areas photographed were randomly selected. A Zeiss Particle Size Analyzer (Model TGZ3) was used to count and measure the sizes of all particles present on the print. About three thousand particles were counted in determining a distribution curve. Electron transmission microscopy was used to determine the effect of annealing on the substructures of the materials. Thin foils were produced by a two-stage thinning process. The rods were first ground on emery paper to ribbons about 10 mils thick and then a jet of 5 pct KOH was used to electrolytically reduce a portion of the cross section of the ribbon. Final perforation was achieved by immersing the specimen in a 5 pct KOH solution and electrolytically polishing at a current density of about 0.3 amp cm-'. The foils were examined with a Hitachi HU-11A electron microscope. C) Tensile Testing. Tensile testing was performed in an Instron Testing Machine equipped with a radiation-type vacuum furnace which operates at about 1O"S torr at temperatures as high as 2400 °C. The same furnace was used for annealing the tensile specimens.

Jan 1, 1970

By B. H. Caudle, L. H. Silberberg

Reservoir depletion by natural water drive is typified by the movement of water from an aquifer into the adjacent oil-bearing formation. Prior studies of this type 01 water movement have generally neglected the resistance to flow in the aquifer and its effect on the movement of water into the oil bearing zone. A method for designing and operating scaled models of such reservoir systems is presented. Experimental data on a model of an edge-water-drive reservoir are shown and discussed. INTRODUCTION Most petroleum reservoirs derive at least a part of their productive capacity from water influx. This water may be injected from the surface or it may come from an aquifer adjacent to the oil zone. In either case, the reservoir engineer must be able to estimate the advance of the water as a function of either the elapsed time or the fluid produced. This paper describes a type of fluid flow model which includes the effect of viscous and gravitational forces in the reservoir and the surrounding aquifer. Natural water influx can be divided into three general (but widely overlapping) categories according to the direction of flow in the aquifer. These are shown schematically in Fig. 1. Fig. l(a) illustrates an edge-water-drive mechanism. In this case, water advances updip along the stratum but the movement of water is essentially horizontal and very little of the oil is actually underlain by water. The bottom-water drive (Fig. l(b)) is characterized by a thick aquifer underlying the oil zone. The water movement is generally vertical in the aquifer. The third category is illustrated in l(c). Referred to as the "thin oil column", this type of oil accumulation consists of oil over water in a relatively thin stratum. Fluid movement is horizontal in both the oil and water zones, except close to the producing well. One characteristic which all three of these types have in common is that part of the water flow takes place in the water invaded region of the oil reservoir while the remainder of the water flow occurs in the aquifer. The resistance to the flow of water usually will not be the same in these two regions. This occurs because the porous rock normally contains only water in the aquifer, while the water-invaded region always contains microscopic globules of bypassed oil (residual oil) which interfere with the flow of water through the rock. The production history of any type of a water-drive system is a function of two phenomena — where the water goes, and how it displaces the oil in the area invaded by the water. It is usually impractical to study these two phenomena at the same time. In most cases one type of analysis is used to predict the gross movement of water in the reservoir, while a different type of analysis is employed to determine the amount of oil to be recovered from the gross volume contacted by the water. The portion of the oil reservoir which is invaded by water is mainly a function of the resistances to fluid flow in the several parts of the flow system. This gross water influx in the three types of natural water drive typically results in water cusping to the production wells either from the side or from below (water coning). In 1747, Muskat described a greatly simplified mathematical model for predicting the area invaded by water in a bottom-water-drive reservoir.1 This model used the Laplace equation and suitable boundary conditions to describe the isopotentials and streamlines in the flow system. The use of this model assumes that (1) the reservoir rock is homogeneous in nature, (2) the oil and water mobilities are equal, (3) there is no oil flowing in the water invaded region, and (4) external forces — such as gravity — do not affect the flow. This method has been used for both natural water drives and water injection projects. In this, as in most models, the method of images is used to reduce the size of the model necessary to describe the reservoir. The assumption of equal viscosities and permea-

Jan 1, 1966

By V. B. Kurfman

Grain refinement of Mg-Al melts by carbonaceous additions has been attributed to nucleation by aluminum carbide. The effects of process and alloy variables are interpreted and predicted in terms of the dispersion and chemistry of this phase. The grain coarsening action of Be, Zr, Ti, R.E., chlorination, temperature extremes, and prolonged holding times is described. Measures necessary to insure an adequate dispersion of the catalyst are discussed. CARBON inoculation treatments have become fairly well known and used for grain refinement of magnesium alloys containing Al. Although there is general agreement that a nucleation process occurs, the process is not understood and the inoculants are used in a rather empirical fashion. The treatment is applied to the class of alloys containing 3 to 10 pct Al, i.e., AZ31A to AM100A. Typical methods involve melting, alloying, and adjusting the temperature to 1400° to 1450°F. Then 0.01 to 0.5 pct C as CaC2, C6C16, or lampblack is added by any convenient means, and the melt poured within 10 to 30 min. Investigators generally have been impressed by an assumed similarity of this refinement process to superheat grain refinement, which depends on heating approximately the same alloys to a temperature in the range of 1550" to 1650°F, then pouring promptly after the melt is cooled to the pouring temperature. Various predictions have been made that carbon refinement would replace superheating in commercial practice due to reduced process costs, but this replacement has not fully taken place because of production difficulties and conflicting observations. Davis, Eastwood, and DeHaven1 agree with Nelson2 and wood3 in suggesting that an excess of inoculant may be harmful. Wood however says that overtreat-ment is not a problem in production use of hexa-chlorobenzene inoculation, and Hultgren and Mitchell4 claim no evidence of harm from excess additions. Various grain coarsening reactions are known to occur, including the possibility of overtreatment mentioned above. Trace amounts of Be,2 Zr, and Ti may prevent refinement by either a carbon treatment or a superheat. Occasionally treatment with cl25 may cause coarsening, although the Battelle refinement process' uses a CC14-C12 blend. Grain coarsening also tends to occur on holding at temperatures below 1350°to 1400°F, especially after a superheat treatment, and for this reason Nelson2 stresses the desirability of a refinement method useful at lower temperatures for open pot melting practice. Since a carbon treatment can be made to work at temperatures below 1400°F, it seems desirable to investigate the mechanism of the refinement and the mechanisms of the coarsening reactions in order to establish control conditions for use in commercial production. The identity of the nucleating phase must first be established and then the factors affecting its chemistry and physical dispersion must be determined. THE IDENTITY OF THE NUCLEATING PHASE Davis, Eastwood, and DeHaven suggested that the nucleating phase in this system is Al4c3,1 but Mahoney, Tarr, and LeGrand8 disagree, largely because they found no evidence of the compound in alloys after carbon treatment and because there is no indication that aluminum carbide should be unstable over the temperature range used in the superheat treatment. This latter objection is based on the assumption that both the carbon treatment and the superheat treatment introduce the same nuclei. Electron diffraction studies have been made to identify the nucleating phase. Samples of grain refined A292 have been selectively etched SO that clean surfaces are obtained and so that secondary phases are in relief. Electron diffraction patterns from these surfaces have established that the carbon treatment of A292 introduces into the metal a large number of small, plate-like particles with a structure very similar to Al4C3. In most cases, the plate-like nature of the particles prevented positive identification but in the cases where the identification could be made the particles proved to be AIN A14C3. However, enough variation in lattice constants was observed so that all compositions from pure A14C3 to the 50:50 solid solution A1N.Al4C3 were probably present.14 In A14C3 and especially AlN.Al4C3 the A1 atoms occur in layers within which they have the same hexagonal symmetry and spacing as the Mg atoms in a single basal plane of a magnesium crystal. The solid solution spacing lies between the 3.16 of AIN and the 3.3? for Al4C3, in satisfactory agree-

Jan 1, 1962

By J. J. Jakosky

The fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.' One of the most important measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtaining bottom-hole data. The applications of bottom-hole pressure or fluid-level measurements are based on simple hydrodynamic principles. Under equilibrium conditions, pbh = hd + pg + pch [1] when pbk = bottom-hole pressure, Ib. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, Ib. per sq. in. per foot, p, = weight of section of gas column 1 in, square from fluid level to casinghead, Pch = casinghead pressure, Ib. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casinghead plus the casinghead pressure. At moderate rates of flow, the rate of production is approximatcly proportional to the difference between the reservoir, or static bottom-hole. pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939

By John Dasher, Wilfred L. Freyberger, James H. Pannell, A. M. Gaudin

WHEN beryllium is bombarded by gamma rays under suitable conditions it evolves neutrons. This nuclear reaction, Bes + y + n + Be", [I] is utilized in the process that is described in this paper. The equation, which physicists often abbreviate to Bevy, n)Be" shows that a photon, y, is absorbed by the Be- sotope of beryllium which then emits a neutron, n, leaving Be8 as a residue." It has been determined that the threshold for this reaction is 1.63 mev; that is, gamma rays having an energy less than 1.63 million electron volts do not have enough energy to remove a neutron from the beryllium nucleus. The threshold value for the beryllium (y, n) reaction is lower than that for any other element. The next most sensitive element is heavy hydrogen (deuterium) whose gamma neutron reaction, D2 (-y, n) H1, has a threshold of 2.2 mev. Thus, gamma rays having an intensity between 1.63 and 2.2 mev will evolve neutrons from beryllium and from beryllium only. Nuclear reactions can be considered as occurring between a projectile and a target. The probability of the occurrence of any such encounter can be expressed in terms of the "cross section" of the target nucleus for the projectile and projectile energy. This cross section, then, is the area normal to the path of the projectile controlled by the target for the purpose of the reaction under consideration. Cross sections are usually expressed in barns, in which a barn is lo-" sq cm. The cross section for Eq 1 is very small, even for nuclear reactions, and of the order of 10"3 barns. It is therefore necessary that a high flux of gamma radiation at the appropriate energy be used to obtain an appreciable neutron yield. In view of the nuclear properties of beryllium it seemed that if pieces of beryllium ore on a moving belt were bombarded with an intense beam of gamma rays, those pieces which are rich in beryllium minerals would emit neutrons at a sufficiently high rate to make it possible to detect that emission, and to use it to actuate a mechanical device for removal of the active from the barren particles. The principal economic source of beryllium is the mineral, beryl. Beryl occurs mainly in pegmatites which are characteristically coarse grained. The suitability of mechanical concentration depends upon the size at which the desired mineral can be liber-

Jan 1, 1951

By Edgar R. Kendall

A knowledge of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. Locating the Supply The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1942

By J. B. Austin, R. L. Rickett

MEASUREMENTS Of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even interpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolation is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1938

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

THE beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than 90 per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as originally proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accumulated since then, showing the utility

Jan 1, 1945

By James H. Pannell, John Dasher, Wilfred L. Freyberger, A. M. Gaudin

WHEN beryllium is bombarded by gamma rays under suitable conditions it evolves neutrons. This nuclear reaction, Bes + y + n + Be", [I] is utilized in the process that is described in this paper. The equation, which physicists often abbreviate to Bevy, n)Be" shows that a photon, y, is absorbed by the Be- sotope of beryllium which then emits a neutron, n, leaving Be8 as a residue." It has been determined that the threshold for this reaction is 1.63 mev; that is, gamma rays having an energy less than 1.63 million electron volts do not have enough energy to remove a neutron from the beryllium nucleus. The threshold value for the beryllium (y, n) reaction is lower than that for any other element. The next most sensitive element is heavy hydrogen (deuterium) whose gamma neutron reaction, D2 (-y, n) H1, has a threshold of 2.2 mev. Thus, gamma rays having an intensity between 1.63 and 2.2 mev will evolve neutrons from beryllium and from beryllium only. Nuclear reactions can be considered as occurring between a projectile and a target. The probability of the occurrence of any such encounter can be expressed in terms of the "cross section" of the target nucleus for the projectile and projectile energy. This cross section, then, is the area normal to the path of the projectile controlled by the target for the purpose of the reaction under consideration. Cross sections are usually expressed in barns, in which a barn is lo-" sq cm. The cross section for Eq 1 is very small, even for nuclear reactions, and of the order of 10"3 barns. It is therefore necessary that a high flux of gamma radiation at the appropriate energy be used to obtain an appreciable neutron yield. In view of the nuclear properties of beryllium it seemed that if pieces of beryllium ore on a moving belt were bombarded with an intense beam of gamma rays, those pieces which are rich in beryllium minerals would emit neutrons at a sufficiently high rate to make it possible to detect that emission, and to use it to actuate a mechanical device for removal of the active from the barren particles. The principal economic source of beryllium is the mineral, beryl. Beryl occurs mainly in pegmatites which are characteristically coarse grained. The suitability of mechanical concentration depends upon the size at which the desired mineral can be liber-

Jan 1, 1951