Search Documents

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

IRON AND STEEL DIVISION Established as a Division February 22, 1928 K C. McCutcheon, Chairman T. L. Joseph, Past Chairman J B Austin, Vice-Chairman E K Miller, Vice-Chairman T. J. McLoughlm, Vice-Chairman Ernest Kirkendall, Secretary-Treasurer CO M M I T T E E S EXECUTIVE J. A. Bowers '54 J. S. Marsh '55 R. W. Campbell '54 D. L. McBride '53 Walter Carroll '55 G. B. McMeans '53 K. L Fetters '53 F. L. Toy '54 H. M. Griffith '55

Jan 1, 1952

By R. E. Holmes, T. W. Leland

The solution to the unsteady-state mass- and heat-transfer equations describing the adsorption of a dilute component from a gas stream flowing through a packed bed is readily applicable to the design of hydrocarbon recovery units. The solution to these equations depends on the assumption of a linear equilibrium equation to relate concentrations on the surface to concentrations in the gas. This assumption is shown to be justifiable for components which are very dilute in the gas stream. This approach permits the prediction of the effects of bed shape and size, cycle time, and gas mass velocity on the recovery of each component. It also allows the time and gas flow rate needed for regeneration to be determined. The equations involve a constant for each component and another constant characterized by the type of adsorbent. These constants must be evaluated from operating data. Values of these constants determined for silica gel are presented. This paper points out the type of experitrrental data needed for a thorough design of hydrocarbon adsorption units. INTRODUCTION The growing importance of adsorption processes to recover hydrocarbons from natural-gas streams has created an urgent need for better methods to design and predict the performance of these processes. Since the original use of solid adsorbents in natural-gas processing was for dehydration, most of the current design methods for hydrocarbon recovery re extensions of those developed earlier for dehydration. These methods are based on an adsorptivity or bed loading factor defined as the amount of a particular component adsorbed per unit weight or per unit volume of the packed bed. The recovery of a given component is then expressed as an empirical function of its adsorptivity on a given adsorbent. In spite of the simplicity and initial utility of these methods, they are not completely satisfactory in that they do not predict the effect of the dimensions of the bed in relation to flow rate and cycle time, and do not predict the distribution of various components along the length of the bed. It is possible, however, to make a considerable improvement in the design of these processes by applying the basic equations of mass and heat transfer applicable to gases containing small concentrations of adsorbing components flowing through granular beds. These equations have been developed and solved by Anzelius,' Furnas,% nd Hougen and Marshall." where G = mass velocity of the inert constituents (assumed to be methane), lb/hr-sq ft, y = weight of an adsorbing component in the gas per unit weight of inert, lb of a given constituent per lb of methane, x = bed length, ft, p, = packed bed density, lb/cu ft, P, = gas density, Ib/cu ft, f = void fraction in the bed, t = time, hours, and w = weight of a given component adsorbed per unit weight of adsorbate free solid, Ib/lb pure adsorbent. The term on the left side of Eq. 1 represents the flow rate per unit bed volume of a component entering less the flow rate per unit bed volume of that component leaving the differential bed length. The terms on the right side represent, respectively, the accumulation rates per unit bed volume on the solid and in the gas phase within the differential bed section. The last term is negligible for this application since pgfv is quite small in comparison with p, and G. The partial differential is determined by the mass-transfer rate between gas and solid in the differential section.

By F. C. Noyes

DAME Nature was in a generous mood when she distributed widely over the face of the globe numerous deposits of phosphate rock from which man can make phosphatic festiIizer to replace the phosphate re- moved from the soil by crops. The principal deposits are readily accessible to the world's greatest consuming areas and most of them are such that mining operations can be carried on at relatively low cost. The world's known reserves shown in Table 1 are sufficient to last well over 2000 gears at the present rate of consumption. Before giving a brief outline of the phosphate rock industry of foreign countries let us try to get a picture of the movement of phosphate rock throughout the world in 1938, the last full normal calendar year where it came from and where it was consumed. Table 2 shows the origin and finial destination of world shipments in 1938 by grand divisions. Table 3 (p. 499) shows shipment9 of phosphte rock to each country in Europe. Europe is seen to be by far the world's greatest market and the French North African mines the world's most important producers outside of the U. S. A.

Jan 1, 1944

By L. B. Schmitt, N. H. Polakowski

Square bars of cold-dvawn copper, mild steel and a 2024 aluminum alloy were forced through an adjulstable gap between two hardened steel rollers by pulling or pushing. The rollers were either free to rotate or were locked in position so that conditions comparable with drawing, rolling, ad containerless extrusion could be created at will. Push or pull forces as well as roll separatirg forces were measured. Forming efficiency and coefficients of friction were determined. For- slow-rate deformation the values ot µ wrere between 0.09 and 0.14. Possibilities for further investigation are indicated. THIS work was undertaken with the aim of a) determining the principal parameters of cold drawing under simplified conditions directly, without recourse to speculative assumptions and b) comparing drawing with rolling and extrusion from the viewpoint of forces involved and deformation efficiency. Data of type a) relating forces in axially-symmet-rical drawing to die geometry. drafting schedules, material properties and lubrication conditions are abundant. Their intrinsic value is. however. limited as long as the radial die forces are unknown. On the other hand. the difficulties associated with measurement of these forces are serious as witnessed by the extreme paucity of such information."" Comparative investigations of type b) were also remarkably few and they all employed ring-shaped dies through which round bars were either drawn or pushed.2-4 Only in one case were the applied and the die splitting forces measured simultaneously.2 In order to simplify the problem, deformation under approximately biaxial conditions was adopted in the present work;. This enables both the drawing (rolling, extruding) efforts and the separating forces to be measured with reasonable ease by conventional methods. Since drawing, extrusion, and rolling can be carried out under virtually identical conditions only in a roller die. an adjustable tool of this type was constructed. The circular die profile involved a difficulty with interpreting the drawing and extrusion data. This was obviated by arbitrarily defining the angle between a contact chord and the drawing plane as the -.equivalent" die semiangle. The simplification was considered permissible since the effect of die angle was not specifically investigated. An additional conlplication was caused by the square cross section of the processed bars. This shape was selected as a compromise between the desire to have as massive as possible specimens and the capacity of the roller die. The metal was only partially restrained from spreading laterally. the flow conditions being therefore intermediate between plane stress and plane strain. On the Huber-Mises yield criterion the constrained and uni-axial yield strengths differ by up to 16 pct but the actual error due to the ignorance of the constraint factor was presumably much smaller than the maximum. In spite of these reservations it was felt that the method employed and results obtained have some merit. With certain further refinements to be indicated later, this technique can yield data perhaps more useful for checking metal forming theories than other, mostly indirect, methods. EXPERIMENTAL Materials—The metals used together with their principal mechanical properties are listed in Table I.

Jan 1, 1961

By Samuel S. Wyer

THE following abbreviations have been used in, the text: Cassier's, Cassier's Magazine. Eng. Lond., The Engineer (London). Eng. Mag., Engineering Magazine. Eng. and Min. Jour., Engineering and Mining Journal. Eng. News, Engineering News. Eng. Rec., Engineering Record. Engng., Engineering. Engr., The Engineer (Chicago). J. I. and S. I., Journal of the Iron and Steel Institute. Jour. F. I., Journal of the Franklin Institute. Jour. Assn. Eng. Soc., Journal of the Association of Engineering Societies. Mar. Eng., Marine Engineering. . Mem, Soc. Ing. Civ., France, Memoires de la Society des Ingenieurs Civils, France. Prac. Eng., Practical Engineer. Proc. Digs. Soc. of W. Pa., Proceedings of the Engineers' Society of Western Pennsylvania. Proc. I. C. E., Proceedings of the Institute of Civil Engineers. Proc. I. 1M. E., Proceedings Institution of Mechanical Engineers. Trans. A. I. M. E., Transactions of the American Institute Mining Engineers. Sci. Am., Scientific American. Sci. Am. Sup., Scientific American Supplement. Zcitschr. d. V. D. Ing., Zeitschrift des Vereines Dentscher Ingcnieure.

Mar 1, 1905

By T. S. Lundy, J. Askill

J. Askill and T. S. Lundy (Oak Ridge National Laboratory)—Moore has proposed a simple correlation between the activation energy for solute diffusion in fee metals and the atomic volume of the diffusing species using both tracer and chemical-diffusion data. The first point we wish to make is that it is wrong to attempt such correlations without separating the two types of data. Activation energies obtained using tracer techniques cannot, in general, be directly compared with those obtained from chemical-diffusion experiments. A knowledge of the variations of chemical potentials with composition is necessary and chemical-diffusion data must be corrected for such variations, even for dilute alloys, before a comparison is possible. Secondly, for nickel, iron, aluminum, and lead, Moore neglected a number of recently published works, e.g., Al26 and Mn54 in aluminum,46 cr51 in nickel,47 and Fe55 in iron.48 These and others should have been used. If one considers only the tracer diffusion data, there is left no simple correlation of the type proposed by Moore. For example, in the case of solute diffusion in aluminum the only reliable tracer data listed by Moore are for zinc and aluminum. The nickel, cobalt, and iron data of Agarwala49 are representative of near-surface diffusion-not bulk diffusion. In conclusion we suggest that for tracer diffusion data in these fee metals there is no justification for proposing any simple correlation of activation energy with atomic volume using the limited data that are presently available. R. H. Moore (author's reply)—The writer has proposed a simple correlation which is useful in estimating the internal consistency of diffusion data. The accuracy of the correlation is, of course, a function of the number of data available. Lundy and Askill take issue with the writer's decision to include data for the systems: nickel, iron, aluminum, and lead, taking the view that the data are insufficient to establish the correlation. The writer agrees that the data are insufficient and has cau- tioned the reader that the correlation is tentative in these instances. Inclusion of these systems is justified by the interesting trends the correlation reveals. For example, the distinction between interstitial and substitutional diffusion may be clearly established, Figs. 4 and 6, and the behavior of transition elements and nontransition elements is indicated to parallel the behavior illustrated by the silver and copper systems. Lundy and Askill have singled out the aluminum system for special criticism. The writer chose to discuss the data for diffusion of iron, nickel, and cobalt in aluminum in the terms used by the original authors9 and has included the comments of Balluffi.l0 The writer did not intend the reader to conclude that data for these elements should correlate with data for the nontransition elements as Lundy and Askill have evidently assumed. Iron, nickel, and cobalt form intermetallic compounds with aluminum, so the activity coefficients of these elements may be expected to deviate markedly from unity. This may account for the low frequency factors observed by Hirano.9 The nontransition elements, on the other hand, yield relatively simple phase diagrams with no evidence for intermetallic compound formation as in the case of iron, nickel, and cobalt. In dilute solution, Henry's law should be closely obeyed, the activity coefficients should not deviate markedly from unity, and the effect on the activation energy should not be large. The accuracy of the correlation applied to these systems will improve as the data is extended. It does not seem unreasonable to conclude that its extension should be encouraged.

Jan 1, 1965

By Arthur B. Foote

THE ball mill has superseded stamps for the reduction of gold ores in most of the recently designed plants, partly because stamps are not suited to die fine grinding required for flotation, and partly to save space and construction cost. Experience with these new mills seems to confirm the idea that it is more difficult to recover bold from a ball-mill product than it is when stamps are used for crushing. Microscopical examination of particles of gold that have passed through a ball mill show that the gold has been pounded into exceedingly thin flakes coated with a talcy surface, making it more difficult to save by amalgamation, flotation, or concentrating. Bearing in mind that gold is extremely malleable, it seems reasonable that this should be so. Contrast the action in a stamp battery, where the crushing is by impact in the presence of mercury, to the grinding and rolling under pressure in a ball mill. It is well known that a better recovery can be obtained by panning or amalgamation from a sample of ore that has been crushed by mortar and pestle than from one reduced on a bucking board.

Jan 1, 1937

By F. Claisse, R. Angers

Self-diffusion in iron has been measured during rapid a-r transformations using a variant of the Kryukou and Zhukhovitskii diffusion method. The study was performed by thermally cycling iron foils (1 to 6 cpm) through the transformation (=910°C). Some foils have been subjected to over 1000 cycles and some have spent more than 15 pct of their total diffusion time in the process of transformation. The experimental results show that the a-r transformation has no measurable effect on self-diffusion in iron. The study is completed by a quantitative analysis of mechanisms which can affect the diffusion rate during the transformation. The analysis confirms the experimental results. SINCE diffusion is an important factor in many solid-state transformations, it is of interest to study how it is affected by the stresses generated during these transformations. Clinard and Sherby1'2 were the first to make a study along these lines. They measured diffusion coefficients in Fe-FeCoV couples subjected to slow thermal cycling (1.5 cph) through the a-r transformation range. They found an enhancement of diffusion by a factor of about two. The purpose of the present paper is to report measurements of the self-diffusion coefficient of iron during much more rapid thermal cyclings (1 to 6 cpm) through the a-r transformation (-910°C). These more rapid cyclings produce higher strain rates during the transformation and should emphasize any possible influence of transformation upon diffusion. EXPERIMENTAL Iron foils, 25 to 35 µ thick, were cold-rolled from 99.92 pct pure iron and annealed in pure helium for 2 hr at 870°C; the resulting grain diameter was about 150 µ. Specimens 0.5 by 8 cm were cut from the foils and I7e55 was vapor deposited on one of their surfaces. A 38 gage alumel-chrome1 thermocouple was spot welded in the middle of one of the specimen long edges, Fig. 1. Two 38 gage chrome1 wires were also spot welded along the same edge on each side of the thermocouple; they were placed 2.5 cm apart and used for electrical resistance measurements. In order to prevent twisting and crumpling, the specimens were pinched between two quartz plates 0.1 by 1 by 7 cm and the assembly was close fitted into a 1 cm ID quartz tube. Four holes were drilled through the tube to let the 38 gage wires out: these were connected to the recording equipment by means of extension wires. 20-gage nickel wires fixed at both ends of the specimens were used to thermally cycle the foils by Joule heating. The above described device was placed in a 2.7 cm ID quartz tube which in turn was placed in a tubular furnace. Either a pure helium atmosphere or circulating hydrogen was used during the experiments. Specimens were subjected to thermal cycles between a minimum temperature To and a maximum temperature Tm at rates ranging from 1 to 6 cpm. This was obtained by maintaining the furnace at a constant temperature near the minimum temperature To and periodically passing an electric current through the specimen. Cooling was achieved by heat losses to the surroundings. The forms and periods of cycles were varied from one specimen to another; however, each specimen was subjected to one type of cycle only. The temperature and electrical resistance variations of the specimens were recorded as a function of time. The temperature curves were used for diffusion calculations while the electrical resistance curves were used to monitor the transformation and to determine its starting point and its approximate duration. Diffusion was measured by the method developed by Kryukov and zhukhovitskii3 and modified by Angers and Claisse.4,5 In this method a metallic foil is coated on one side with a radioactive isotope and the activity is measured periodically on both sides during the diffusion anneal. The following equation then holds: where: I1 Activity on the surface on which the deposit is made. I, Activity on the opposite surface. t Diffusion time. B Constant. D Diffusion coefficient. d Foil thickness including the deposit. G(t) A function of time; it is a second order correction term which is given graphically in Refs. 4 and 5. The diffusion coefficient D is found by plotting ln[(Il - I2)/(I1 + I,)] -G(t) against t; the resulting slope m leads to an accurate calculation of D through Eq. [2]. The effect of the a-r transformation on diffusion is expressed by the ratio DT/DU where:

Jan 1, 1970

By R. E. Heithecker

Almost every oil well drilled into limestone formations in Kansas is treated with hydrochloric (muriatic) acid upon completion: to increase potential capacity of well and thereby increase its "daily allowable" production; to shorten time required to produce recoverable oil; and to increase quantity of oil recovered ultimately from reservoir. Acid treating marked a forward step in the producing fields of Kansas; in fact, many old limestone fields that almost had reached their economic producing limit were "rejuvenated" with acid and their capacities to produce increased several times. It also caused a marked increase in the ultimate oil recovery of some old and nearly depleted fields of Kansas. The effect of the acid was due to the cleaning-out action by the acid at the face of the limestone, the enlargement of the small drainage channels, and the apparent penetration of the acid to previously undrained porous and saturated strata. Studies of the effects of acid were made in the Fairport field, three groups of wells in the El Dorado field and the Shutts field. Estimation of increased recoveries resulting from acid in these fields and groups of wells ranged from 1000 to 2400 bbI. per acre. Limestone structures that had been tested by drilling and found noncommercial were later completed as commerical oil-producing formations through the use of acid. The Kansas City formation, Valley Center field of Kansas, is an example. Increased oil production and revenue from the old fields justified the reconditioning of equipment, which in most cases had become in poor mechanical condition. The first treatment with hydrochloric acid of an oil well in Kansas was in October 1932, and by the end of 1937 almost 6000 wells had been treated. Many wells were treated more than once and the total number of treatments exceeded 8000 by the end of 1937. Approximately 12 3/4 million gallons of acid was required for these treatments. The report includes 15 illustrations and 16 tables.

Jan 1, 1939

By R. E. Heithecker

Almost every oil well drilled into limestone formations in Kansas is treated with hydrochloric (muriatic) acid upon completion: to increase potential capacity of well and thereby increase its "daily allowable" production; to shorten time required to produce recoverable oil; and to increase quantity of oil recovered ultimately from reservoir. Acid treating marked a forward step in the producing fields of Kansas; in fact, many old limestone fields that almost had reached their economic producing limit were "rejuvenated" with acid and their capacities to produce increased several times. It also caused a marked increase in the ultimate oil recovery of some old and nearly depleted fields of Kansas. The effect of the acid was due to the cleaning-out action by the acid at the face of the limestone, the enlargement of the small drainage channels, and the apparent penetration of the acid to previously undrained porous and saturated strata. Studies of the effects of acid were made in the Fairport field, three groups of wells in the El Dorado field and the Shutts field. Estimation of increased recoveries resulting from acid in these fields and groups of wells ranged from 1000 to 2400 bbI. per acre. Limestone structures that had been tested by drilling and found noncommercial were later completed as commerical oil-producing formations through the use of acid. The Kansas City formation, Valley Center field of Kansas, is an example. Increased oil production and revenue from the old fields justified the reconditioning of equipment, which in most cases had become in poor mechanical condition. The first treatment with hydrochloric acid of an oil well in Kansas was in October 1932, and by the end of 1937 almost 6000 wells had been treated. Many wells were treated more than once and the total number of treatments exceeded 8000 by the end of 1937. Approximately 12 3/4 million gallons of acid was required for these treatments. The report includes 15 illustrations and 16 tables.

Jan 1, 1939

By J. Burns Read

IT IS the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnance Department, during the War, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Ordnance Department in obtaining these data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The manufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodicals and, therefore, will not be given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540° to 650° C. (1000° to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases are then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followed, by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430° to 480° C. (800° to 900° F.) by immersion in a salt bath or by gas flames. After being washed, the cases are tapered, when they are ready for machining, inspection, and testing.

Jan 4, 1922

The following is an incomplete list of members and guests who called at Institute headquarters during the period Feb. 10, 1918 to Mar. 10, 1918: W. G. Anderson, St. John, N. B., Canada. Charles E. Locke, Boston, Mass. L. M. Banks, Camp Meade, Md. E. T. Lednum, Joplin, Mo. P. E. Barbour, Albany, N. Y. C.' K. McDonald, Washington, D. C. Alan M. Bateman, New Haven, Conn. C. T. Malcolmson, Chicago, Ill. Graham Bright, Pittsburgh, Pa. Stuart B. Marshall, Badin, N. C. J. F. Callbreath, Washington, D. C. T. C. Merriman, New Haven, Conn. J. E. S. Clark, Riverside. Cal. Arvid E. Nissen, Gary, Ind. G. H. Clevenger, Palo Alto, Cal. Herbert G. Officer, Conway, S. C. George C. Crossley, Trenton, N. J. J. E. Parker, Bulawayo, Rhodesia, S. Afr. R. H. Eagles, Palmerton, Pa. Francis R. Pyne, Elizabeth, N, J. Charles Enzian, Pottsville, Pa. Alfred Hull Ramage, Joplin, Mo. Albert H. Fay, Washington, D. C. H. H. Stoek, Urbana, Ill. David B. Gemmill, Crown King, Ariz. G. M. Taylor, Colorado Springs; Colo. Ronald Harris, London, Ont., Canada. Charles Tubby, St. Paul, Minn. Wm. J. Hayes, Colombia. So. America. J. B. Tyrrell, Toronto, Canada. B. B. Hood, Chrome, N. J. Edmund W. Westervelt, Ymir, B. C. 0. P. Hood, Pittsburgh, Pa. Carl Zapffe, Brainerd, Minn. H. M. LaFollette, LaFollette, Tenn. W. S. Boyd, formerly superintendent of mines of the Ray Consolidated Copper Co., has been appointed assistant general manager. William Campbell, Professor of Metallurgy, at Columbia University, is acting as metallurgist at the New York Navy Yard.

Jan 4, 1918

By R. V. Norris

1. INTRODUCTION. THE anthracite coal trade, with a shipment averaging about 70,000,000 tons per year, differs essentially from other coal business, in the fact that the larger sizes, comprising about 65 per cent. of the total, are used almost exclusively for domestic purposes, principally during the winter months; and that for proper combustion close-sizing is imperative, so that eight sizes are made; broken, egg, stove, and nut, known as prepared sizes, and pea, buckwheat, rice, and barley, known as steam sizes. These sizes are made in the regular course of preparation, and but little variation in the natural percentage of each is practicable. Thus it is necessary either to work the collieries intermittently, or to dispose of all the varying sizes in their fixed proportions. Unfortunately, the market does not at all times absorb the coal in proper proportions, and rather than interfere with the regular operation of the mines it has been found economical to provide storage for the excess. While the cellars of the consumers are the great storage-plants of the country, this capacity is not under the control of the trade, except so far as reduced prices during the spring and summer months may tempt the use of this reserve. The same remark applies but with less force to the retail yards, which,, though usually small, store in the aggregate a large amount of anthracite. While every effort is made to utilize to the utmost the individual storage-capacity of the country, there still remains the necessity for taking care of the irregularities of the market by the construction of storage-plants under the direct control of the producers. Such plants are usually the property of the railroads, and are situated at points most convenient from a traffic stand-point.

Jun 1, 1911

By Earl E. Hunner

At the end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping southwest, or exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a north-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly. Problems and Plans In order to understand what follows, the general layout and equipment of the mine as it was at this time must be briefly described. Fig. 6 indicates the relative positions of the shafts. The North Star (incline) shaft extends from the surface to the 6300-ft. level following the vein, with an average pitch of 26", between limits of 11" to 38. There is at present no hoisting equipment in this shaft between the 2700 and 4000-ft. levels. The Central (vertical) shaft connects with the North Star shaft at the 4000-ft. level, at a vertical depth of 1600 ft. In two compartments of this shaft 4-ton skips made a vertical turn of 15 ft. radius at the 4000-ft. level and ran down the incline to the 6300-ft. level. A cage operated in the third compartment to the 4000-ft. level. Men and supplies were transferred to a truck running on a third track down the incline shaft to the 6300, operated by an electric hoist on the 4000-ft. station. When the shifts changed double-deck cages were substituted for the skips in the vertical shaft, but they stopped at the 4000-ft. station. The truck to 6300 carried 22 men, and it required 8 min. to make a trip down and back. This arrangement was satisfactory as long as a fairly large proportion of the work was

Jan 1, 1930

By Frederic Brunton

I. INTRODUCTION THE smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at' very high efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of $1.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 tons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by Alfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Works, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913).

Jan 7, 1915

By R. B. Mears, G. F. Sagar, R. H. Brown

There are well recognized procedures for determining the various tensile, fatigue, and other mechanical properties of the common structural materials. This makes it possible for engineers to design structures of various materials which have adequate initial strength to stand the stresses to which they are subjected in service. There is also considerable general information about protective measures suitable for protecting the usual structural materials from the effects of ordinary environments. However, often insufficient quantitative information is available on the combined effects of stress and corrosion to permit the designer satisfactorily to appraise the structure from the stress-corrosion standpoint. This situation is further complicated by the fact that the stresses causing stress¬corrosion failures are usually not the design stresses but rather the residual forming and assembly stresses which are generally of unknown magnitudes. Thus, tests which will rapidly evaluate the susceptibility of materials to stress-cor¬rosion failures are extremely useful. Of particular value are tests which can be applied to built-up structures as well as to simple specimens, since, as mentioned above, residual stresses often are caused by fabricating procedures and assembly operations. The present paper contains

Jan 1, 1945

CONTENTS PAGE Bronze Bearing Metals. By G. H. CLAMER 1729 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. WARING . . 1733 The Tin-plate Industry. By D. M. BUCK. Discussed by G. H. CLAMER, J. W. RICHARDS 1735 The Aluminum Bronze Industry. By W. M. CORSE 1738 Bronzes, Bearing Metals, and Solders. By G. K. BURGESS and R. W. WOODWARD. Discussed by G. H. CLAMER, R. T. ROBERTS 1742 Babbitts and Solder. By G. W. THOMPSON 1751 The Cadmium Supply Of the United States. By C. E. SIEBENTHAL. Discussed by M. L. LISSBERGER, C. W. HILL, F.- F. COLCORD . . .. . . . . 1752 Solder, Its Use and Abuse. By M. L. LISSBERGER 1759

Jan 12, 1918

By Edward Griffith

The anthracite industry, which produces about 50 million net tons of coal annually, has been talked of as being able to last for another century; but if the water record of the past century continues into the expected century, this expectation of many years production still to come out of the remaining reserves will not be attained. The industry will be a submerged one in fact as well as in name. A recorded forecast of what has since occurred appears on page 34 of the Mine Inspectors' reports of 1897: It should also be noticed that bodies of water had accumulated in parts of abandoned mines before duplicate surveys of the same were required by law; and as a result we have today to contend with bodies of water, the exact location and position of which are not correctly known. Since that date, 47 years ago, the implications of the foregoing comment have grown enormously. This is shown in Fig. I and in the following table showing flooded and partially flooded areas that have come into existence since the early 1930's in the northern anthracite field: Number of Year Flooded Areas 1932...................... 2 1933...................... 3 1934..................... 3 1935...................... 5 1936...................... 7 1937...................... 9 1938.................... 11 1939...................... 11 1940...................... 11 1941...................... 14 1942...................... 14 1944...................... 26 Similar conditions exist in other fields in the anthracite region. In the period between 1923 and 1940, abandonment of collieries in the southern field resulted in the flooding of approximately 60 sq. miles (30 per cent) of the field. The ahandonment of collieries in this field has imposed additional expense for pumping on the collieries still operating. This condition will be aggravated by the extension of developments and cause suspension of operations if economic conditions do not justify the assumption of additional pumping costs. During the years, the region's rainfall has not altered, but the quantity going inside the mines through breakages in the surface, brought about by extraction of the coal, has increased materially, as indicated by the ratio of tons of water pumped to tons of coal produced underground for one of the large companies in the northern anthracite field: Year Ratio 1920................. 8.4:1 1925.................. 10.6:I I930.................. II.4:I 1935................. 26.2:1 1940.................. 32.7: I 1942.................. 30.3:I The data in Table I shows the total amount of water pumped and its ratio to underground production for one of the large companies in the southern anthracite field, and shows a rapidly growing serious situation. Rainfall quickly affects the workings in all the fields. In mine inspection district 7 of the southern field the rainfall in 1935 was 92,083,000,000 gal. The total water pumped was 36,274,000,000 gal. (39.4 per cent of the rainfall). The operating mines

Jan 1, 1947