Search Documents

By W. M. Small

From the one producing well in Austria, 7000 bbl. of heavy oil was produced and sold in 1933. This well, owned by the Raky-Danubia, was completed late in 1932 in the formation called Flysch (Upper Cretaceous or lower Eocene) near Zistersdorf north of Vienna. Two wildcats drilling in the vicinity have not yet reached the producing beds. Near Vienna, the European Gas and Electric Co. drilled five shallow wells for gas, three of which were failures. One gas well was completed for 8 million cu. ft. capacity at 260 meters depth and with a pressure of 570 lb. Another is being tested following blowouts. One gas well and one dry hole were completed in the pool in 1932. In Upper Austria, the same company abandoned one wildcat at 679 m. and is drilling at 280 m. on a second. No gas was sold during the year, but a line is being completed to supply fuel to boilers of the Vienna Electric Works. Hungary No deep drilling was done in 1933. Oil and gas concession was granted by Parliament to the European Gas and Electric Co. on Trans-danubia. Active geological and geophysical investigation is in progress. Czechoslovakia In the Gbely and Hodonin shallow fields, some 26 wells were drilled of which three were reported as failures. The total production of the fields was 111,736 bbl. of oil and 40 million cu. ft. of gas used as fuel in the field. At Vacenovice, where there were already two small gas wells, a third producer was completed at 420 m. This pool markets a small amount of gas, which is compressed and used to light railway carriages. Wildcat wells were reported drilling at about 300 m. depth at both Jasina and Telnice. One 700-ni. wildcat near the Hodonin field was abandoned. Another failure was reported completed and abandoned at 820 m. near Holic.

Jan 1, 1934

By Eckley B. Coxe

I wish to call the attention of the Institute to a peculiar variety of anthracite which occurs in the Buck Mountain vein at our collieries at Drifton, and in the same and other veins in different localities in the anthracite coal-fields. It is known among the workmen as iron-gray or cast-iron. It has a dull, greasy appearance, as if a piece of ordinary anthracite had been rubbed with a dirty and greasy rag and allowed to dry. It was formerly considered a very impure coal containing a high percentage of ash, and was picked out of the coal and thrown away. But the following analysis of it and of its ash, made by Mr. J. Blodget Britton, of Philadelphia, shows that such is not the case, the percentage of ash not being much higher than that of the ordinary anthracites as they are prepared for market. ANALYSIS OF COAL. Water,.........4.36 Fixed carbon, by difference,.. 84.90 Volatile combustible matter,. . 3 48 Ash,..........7.26 100.00 The carbon proved to some extent to be of the nature of graphite, and slowly combustible. ANALYSIS OF ASH. Silica,.........25.66 Sulphur,........ .17 Alumina,........27.03 Phosphoric acid,.......21 Ferric oxide,.......42.83 Alkali, undetermined matter and Lime,.........1.56 loss,.........60 Magnesia,........1.83 Manganous oxide,......11 100.00 We recently collected a quantity of the substance and made a fire with it, in an ordinary stove, which was kept up several days. We found that it burned with intense heat, and apparently as freely as our other coal does. Mr. Britton is probably right in his view, that the difference in appearance is not due to impurities in the coal, but to the fact that the carbon is in a more or less graphitic form, as many of the standard coals are no purer. I bring this before the Institute as I know that a large quantity of this valuable fuel is thrown away every year, on account of its supposed impurities.

Jan 1, 1879

By T. A. Rickard

Clement Le Neve Foster was born at Camberwell on March 23, 1841, his father being Peter Le Neve Foster, who was secretary of the Society of Arts for 26 years. As a boy of 12 he was sent to school at Boulogne, receiving a preliminary education there; and in 1857, when only 16 years old, he took his degree of Bachelor of Science from the University of France. In October of the same year he returned to London and entered the Royal School of Mines, which was then in Jermyn Street. He distinguished himself by winning a scholarship and a medal, and by securing his degree as Associate of the Royal School of Mines in the abbreviated period of two years. This was followed by a year at the Bergakademie at Freiberg; subseque1:tly he visited several mining districts in Germany and Hungary. On returning to England, in November, 1860, he received from Sir Roderick Murchison an appointment upon the Geological Survey. During five years he was engaged in field-work, first on the Wealden beds in Kent and Sussex, and then in Derbyshire and Yorkshire. At this time his evenings were largely devoted to reading for a degree from London University. In 1861 he matriculated, obtaining the Bachelor of Science in 1863, with honors in biology and a University scholarship in geology; in 1864 he passed the two examinations entitling him to the Bachelor of Arts degree, and in 1865 he received the degree of Doctor of Science. In 1865 he succeeded Mr. Richard Pearce as lecturer to the Miners' Association of Cornwall and Devon. At the same time he became the curator to the museum of the Royal Geological Society of Cornwall at Penzance, a member of the council in 1873, and a life-member in 1874; he made frequent donations to the museum, besides contributing several valuable papers to

Jan 1, 1905

By Morris M. Fine, Norwood B. Melcher

It is out of the question, at this time, to select any one prereduction process as superior to the others. It is apparent that several share a basic similarity and that within the groups listed in Part 1, the reduction vessel is sometimes the only significant variable. Claims as to the virtues of one machine over another are difficult to substantiate: one may be rapid, another thermally frugal. Based on published data, however, all seem to be performing adequately. It would appear that processes based on carbonized pellets are most applicable to foundry iron at low production rates. Adaptation to large scale manufacture of blast furnace hot metal or to agglomeration of fine concentrates at the mine site is much less likely.

Jan 8, 1966

By John V. Beall

Cutting costs and increasing safety with new ideas is the byword with The Cleveland-Cliffs Iron Co. on the Marquette Range in Michigan. Among the new ideas being tried out are mechanical shaft mucking, prefabricated lagging to replace timber poles, Carset bits in shaft sinking, and rubber tired guide wheels on the ore skips. Plans are being made to stockpile ore with conveyor belts during the winter. In sinking the Mather "B" Shaft a 3/8-yd clamshell-type bucket is used for mucking. The clamshell is opened and closed by means of a verticallymounted hydraulic ram actuated by 5000 psi oil pressure. An Ingersoll Rand-type hoist is used to raise and lower the clamshell. The hoist is controlled by one member of the crew on the floor of the shaft. When the bucket is raised, the men swing it over the muck pile to the desired position and then it is lowered on to the broken rock. The 1400-lb weight of the bucket causes it to sink into the broken rock and it digs as the ram closes the bucket. The hydraulic ram is operated by a man on the lowest shaft steel set who controls a specially designed oil pump which supplies oil pressure. The clamshell is emptied.

Jan 1, 1949

By Zay Jeffries

Rearmament superimposed on buying sprees by the public, caused a general shortage of metals in 1911. and the rare metals were no exception; they also shared with the more common metals the uncertainty of future demand. In general, the apparent undersupply of metals is a favorable condition for the realization of sleeping possibilities of the rare metals, especially if the supply can he made sufficient to take care of the possible new demand. Many changes in metal usage in 1941 were forced because of shortages. When such changes are in the direction of the economic trend there is a speeding up in the tempo of the inevitable change, but when the forced changes are against the economic trend they are likely to be shortlived. In any event, the latter is not a solid foundation on which to build a future business.

Jan 1, 1942

University or College Society President Secretary Alabama, University of University. Ala Mining and Metallurgical Society Warren G. Payne Melbon J. Langley Alaska Agr. College and School of Mines, College, Alaska Alaska Mining Society Robert McCombe Robert Mize Arizona, University of, Tucson, Aria Miners' Society Frank Bacon Charles V.' Harris California University of, Berkeley, Cal...: Students Mining Association C. F. Bedford J. R. Hollcraft, Jr. Came is Inst. of Technology, Pittsburgh, Pa The Miners and Metallurgists Society Richard M. Barnhart Jack E. Morris Case School of Applied Science, Cleveland, Ohio Pick and Shovel Club R. H. Randolph W. B. Scott Colorado School of Mines, Golden, Colo Student Branch of A. I. M. E, Donald Peaker T. H. Evans Jones Harvard University, Cambridge, Mass Geological Club H. E. Quinn Lincoln Thiesmeyer Idaho, University of, Moscow, Idaho Associated Miners John T. Carpenter Robert D. Baily Illinois, University of Urbane, Ill Mining Society H. M. Adams R. M. Sherer' Kansas University of, Lawrence, Kane : Student Branch of the A.I.M.E. Henry Gould Everett Stidham Kentucky, University of, Lexington, Ky : Norwood Mining and Metallurgical John D. Lancaster James A. Purnell

Jan 1, 1929

World Petroleum Consumption. By V. R. GARFIAS AND R. V. WHETSEL. (Trans, vol 107). A tabulation showing world consumption of gasoline, kerosene, gas and fuel oil, lubricants, and miscellaneous petroleum products by counties in the years 1931, 1932 and 1933 , Totals are given; for instance, Cuba consumed 3,998,000 bbl of all petroleum products in 1933, in 1933; the world consumed 1,366,291,000 bbl. of all petroleum products, etc. Domestic Production. Annual Symposium of Petroleum Division, February Meeting, 1934 (Trans, vol. 107. 181 pages.) The symposium consists of reports on petroleum and gas developments and production in the producing states of the United States. This year the statistical information is presented in a new and far more comprehensive form. The reports on domestic production are as follows: Arkansas, by B C Craft; California, by V H. Wilhelm and H. W. Miller, Colorado, by C. E. Shoenfelt, Illinois, by A H Bell, Indiana, by W. N Logan and P. Simpson; Kansas, by Marvin Lee; Kentucky, Ohio and West Virginia, by V. C Smith; Louisi¬ana, by B C Craft, Michigan, by Theron Wasson; Mississippi, by B C Craft; Missouri, by F C Greene, Montana, by H. N Hickey, New Mexico, by C. E Shoen¬felt and D E Winchester, New York, by D. H. Newland, Oklahoma, by L. G. E. Bignell, J 0 Lewis and E. A Hanson, Pennsylvania, by G H Fancher, Tennessee, by L. C Glenn, Central Texas, by R B. Kelly and P R Martin, East Texas, by A R. Denison, Gulf Coast, by L P Teas, North Texas, by H B Fuqua and B. E Thomp¬son; North Central Texas, by J M. Armstrong, Panhandle, by R H Lynn and T. C. Craig, Southwest Texas, by 0. G. Bell; West Texas, by C W. Reith, Utah, by E S Shaw, Wyoming, by J G Bartram.

Jan 1, 1935

By G. S. Cole, G. F. Bolling

Recent experitnents on crystal growth have indicated that thermal convection in the liquid influences the conditions of solidification and subsequent crystal characteristics. However, the important columnar-equiaxed transition in castings has not been examined as a function of this free convection. An experiment is presented here to demonstrate a change in the transition as convection is suppressed. Lead- and tin-based alloys were cast in stainless-steel molds either without special procedures or with thin grids placed horizontally across the tnold diameter in portions of the castings. While the grids allowed some diffusion of heat and mass transport to occur during solidification, massive fluid flow was hindered in the vegiotz of the grids. A larger percentage of columnar grains appeared in the grid region than in other parts of the special castings or than in all regions of normal castings. This structural difference can be explained in terms of thermal convection. THERE is little information about the possible effects of natural convection which may occur during the solidification of a casting. Ruddlel-3 has stated that the movement of liquid metal produced by convection might assist in the transfer of heat, but in the absence of confirmatory evidence he suggested that this idea be treated with caution. chalmers4 considers, but does not assess, the importance of fluid motion in casting, while Tiller5 suggests that, in liquid metals which have extremely high thermal diffusivities, the effects of thermal convection may be negligible. In addition, throughout the literature, there are statements indicating the possible presence of thermal convection but without proofs or evaluations of its influence. Natural convection may be divided into two categories: thermal convection, where liquid flow is due to density differences caused by temperature gradients in the liquid (e.g., liquid near a cold wall falling with respect to hotter liquid further away from the wall); and solute convection, where flow is due to density differences as a result of concentration gradients, see Wagner.6 In most instances thermal convection predominates over solute convection. Nevertheless, even thermal convection has not been studied in any detail and is difficult to handle, since it can vary quantitatively from one experiment to another depending upon the exact positions of heat sources and sinks or the attitude of the container with respect to gravity. In spite of these difficulties it is possible to realize that a higher rate of heat transfer must result with convection than in any situation where conduction acts alone. Thus, the degree of increased heat transfer is the important undecided question in considerations of casting. It will be demonstrated here that a reduction in convective flow leads to a suppression of the columnar-equiaxed transition in a casting and that this suppression is related to a decrease in the degree of heat transfer. Fortunately it is possible to do this by comparative rather than quantitative measures. The insertion of horizontal plates or grids into a simple mold does not appreciably influence heat transfer per se, but in reducing the allowable height through which colder liquid may fall freely it reduces natural thermal convection. This leads to a reduced fluid velocity, a different flow pattern, and an altered heat transfer which can be measured. EXPERIMENTS The alloys were prepared from elements of 99.9 pct nominal purity and cast into an uncoated 2-in.-diameter stainless-steel mold insulated at the bottom with a suitable refractory so as to ensure predominantly radial heat flow during freezing. Casting was performed either in empty molds or in molds containing grids or plates in various configurations . The grids were constructed of aluminum screen (1/32 in. thick) which was cut to the desired shape, cleaned in aqua regia, and coated with a mixture of 2 parts aqua dag graphite -1 part Sauereisen cement mixture, thus supplying a hard, protective, and insulating layer approximately 0.006 in. thick. The

Jan 1, 1965

By Alistair Frame

INTRODUCTION In April 1988 discussions were about to start with BP on the possibility of buying their- mineral interests, and it took a long time to arrange a deal. I will talk about RTZ without BP Minerals, look at the new RTZ with BP Minerals, discuss the outlook for metal prices, and review the problems in South Africa and develop the case against sanctions on that country. RTZAT THE END OF 1988 Late in 1987, after completing a worldwide review of our strategic thrust, we decided: 1. That the business focus would be to remain a major diversified natural resource group with interests in related industries. 2. To divest non-core and low growth businesses. 3. To develop a logical acquisition plan. 4. To emphasise organic growth and, most importantly, to enhance shareholders' wealth by capital increase and a progressive dividend policy. Subsequently, we concluded that we should sell our oil and gas business and dispose of several assets for which we saw little growth potential. The disposal programme raised some U.S.$ 1,600 million, representing a significant capital gain on our various investments. All transactions were carried out by our small Head Office staff in London, without the help of merchant banks and lawyers, and we were able to safeguard the employment of our staff in all these operations. The most interesting disposal was of our oil and gas interests. Before the 1987 strategic review, we had ambitions to develop our oil and gas interests and to become the leader in the second division of European oil companies. Our interests, which were purely in exploration and production of oil and gas, consisted of the 100% owned RTZ Oil and Gas company, and 29% of LASMO, a publicly quoted U.K. oil and gas company with extensive worldwide interests. LASMO, in turn, owned 25% of Enterprise Oil, one of the more successful of the North Sea oil exploration and production companies. Prior to the end of 1987, our intention was to acquire control of both LASMO and Enterprise. However, when we evaluated the net asset value of these two companies based on our oil price assumptions, which were pessimistic for the next five years or so, we concluded that they were both trading in the market at significant premiums. This, taken with the additional premium required for acquisition and the high cost of exploration, led us to conclude that, since funds could undoubtedly be used to better effect, we should sell our interests. Turning to the other major achievements in 1988, we commissioned, and built up to design levels in a very short period of time, the Morro do Ouro gold mine in Brazil. This mine reached its design output of 100,000 ounces of gold per year within three months of start-up, which was on time and under budget. We are now considering a possible expansion of this property. In South America, Utah International, Mitsubishi and RTZ arranged non-recourse finance, with post completion guarantees, for the giant Escondida Project in Northern Chile. Financing came from a group of banks in Japan, Germany and Finland -- the countries to which most of the concentrates will be sold -- and from the LEC. The average output of the mine for the

Jan 1, 1990

By F. Ernest Brackett

Much new data on the flow of gases have been discovered by recent experiments by the United States Bureau of Mines and others. Although additional investigation is still desirable, the information now collected seems sufficient to attempt a tentative coördination of the friction factors. This study is confined entirely to fluid friction when the density throughout the duct is so nearly constant that it may be so considered. In the subsequent discussion the following notation is used: v = mean velocity of fluid in duct, feet per second. v' = mean velocity of fluid in duct, meters per second. R = hydraulic radius of duct, feet. R' = hydraulic radius of duct, meters. S = the hydraulic slope. P = pressure absorbed by friction, pounds per square foot. p = pressure absorbed by friction, pounds per square inch. p' = pressure absorbed by friction, kilograms per square centimeter. A = sectional area of duct, square feet. O = perimeter of duct, feet. L = total length of duct, feet. L' = total length of duct, meters. d = diameter of a cylindrical duct, inches. w = density of the fluid, pounda per cubic foot. g = specific gravity of the fluid compared with water = w % 62.4. C, k and B, coefficients for formulas using English measures. C' = metric coefficient, v' = C'R'S. n = coefficient of roughness for English or metric units. The basic formula for the flow of all fluids at constant density appears in the three following forms, which may be denominated: (a) The slope formula, v = CRS (b) The ventilation formula, " n = (c) The pipe formula, C is Kutter's coefficient, which is extensively applied to the flow of water in ducts and channels of all kinds; E is Atkinson's coefficient, used principally with air in ventilation problems; B is a coefficient conveniently adapted to studying the flow of water, gases and vapors in pipes. 312

Jan 1, 1927

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

The following is an incomplete list of members and guests who called at Institute headquarters during the period July 11, 1918 to August 11, 1918. John Carter Anderson, Tucson, Ariz. Edson S. Pettis, San Francisco, Cal. Lieut. Frank A. Ayer, Tyrone, N. M. Wm. H. Rettie, Yonkers, N. Y. W. R. Canton, McGill, Nev. J. T. Robertson, Port Richmond, S. I. Alden Crankshaw, Palmerton, Pa. Harry O. Robinson, Margarita, John Davenport, W. Norfolk, Va. Venezuela. A. Faison Dickson. C. K. Seng, Gilbert, Minn. F. A. Fahrenwald, Cleveland, C). E. S. Sheffield. L. Hall Goodwin, New York. H. G. Smith. W. H. W. Hamilton, Baker, Ore. Harry M. Spoor. Floyd D. James, St. Louis, Mo. H. H. Stoek, Urbana, Ill. George A. Laird. Arthur L. Tuttle, Copperhill, Tenn. J. W. McBride, Spokane, Wash. Thor Warner, Phoenix, Ariz. Arthur Notman, Bisbee, Ariz. Christopher G. Atwater, Manager Agricultural Dept., The Barrett Co., is in Washington serving the U. S. Navy Bureau of ordnance in connection with the Navy nitrate plant recently authorized by Congress. Edward Ludlam Blossom announces his marriage to Mabel Townsend, daughter of Mr. and Mrs. George Comings Mills, on Wednesday, July 17, 1918, at New York City.

Jan 9, 1918

[Separates of all the Pamphlets published within the last three years (starting with No. 1469) are available, with few exceptions, at Institute headquarters. Separates of all the Technical Publications are also available. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.] METAL MINING TRANS. PAMPHLET VOLUME NUMBER TITLE AUTHOR MEETING AND PAGE* -1033 Relation of Air Pressure to Drilling H. W. Seamon New York 66,743, 766 Speeds of Hammer Drills Feb., 1921 1034 Time Factor in Depletion of Mines J. W. Roberts New York - 66,711 Feb., 1921 1 1035 Calculation of Ore Tonnage and Grade J. E. Harding New York 66, 117, 122 from Drill-hole Samples- Feb., 1921 1038 Discussion of Papers Presented in 1920 1041 Run-off and Mine Drainage - H. N. Eavenson New York 66, 624, 630 Feb., 1921 1043 The Health of the Underground Worker A. J. Lanza New York Feb., 1921 1045 Dust-ventilation Studies in Metal D. Harrington New York 66, 272, 282 Mines Feb., 1921 1046 Discussion of Papers Presented at New York Meeting, 1921 1072 Breakage and Heat Treatment of Rock- B. F. Tillson New York 66,758 drill Steel Feb., 1921 1073 Discussion of Papers Presented at New York Meeting, 1921 1076-M Analysis of Some Drill-steel Tests F. B. Foley New York - 66,789 Feb., 1921 1077-M Application of Magnetic Analysis to C_ W. Burrows New York 66,796 Root Drills Feb., 1921 1078-M Heat Treatment of Rock-drill Steel G. H. Gilman New York 66,779 Feb., 1921 1080 What is the Ideal Drill Steel? F. H. Kingdon New York 66,807 Feb., 1921 1081 Rock Drill Steels, etc. W. T. Ober New York 66,814 Feb., 1921 1082-C Underground Mine Development, Its J. B. Dilworth Wilkes-Barre 66, 715, 721 Definition and Valuation Sept., 1921 1084 Drill Steel from Hollow Ingots P. A. E. Armstrong New York 66,809 Feb., 1921 1088 Authors' Replies to Recent Discussion 1092 Heat Treatment of Rock Drill Steel A. E. Perkins New York 66,811 Feb., 1921 1096-M Octagonal Ventilation Shaft of Davis- J. L. Bruce Wilkes-Barre 66, 252, 268 Daly Copper Co. Sept., 1921 1100-C Determination of Electrical Equip- G. Bright Wilkes-Barre 66, 580, 605 ment for a Mine Hoist Sept., 1921

Jan 1, 1926

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By BARONJUPTNER VON JONSTORFF, Andrew A. Blair, GUNNAR DILLNER

IT is a well-known fact that the results of different analysts, when operating on the same identical sample of steel or iron, are far from concordant, and it not infrequently happens that great annoyance and trouble in the commercial community are occasioned by these discrepancies. Attempts have been made at various times to investigate the causes of such differences and to obtain more reliable methods of analysis. The most important of these was made by the British Association in 1889: The following gentlemen, with Sir W. Roberts-Austen as Chairman, and Professor T. Turner as Secretary, were constituted as a committee to investigate the question, viz.: Sir F. A. Abel, Mr. Edward Riley, Mr. G. J. Snelus, Mr. John Spiller, Professor J. W. Langley, and Professor Tilden. Average .samples of steel were prepared in America under the superintendence of Professor J. W. Langley. The steels, in the form of turnings, were divided and distributed to sub-committees in Great Britain, America, France, Germany, and Sweden. In Sweden Professor Åkerman acted as Secretary to the Swedish committee. The Government Department of Tests was appointed in Germany; Mr. Ferd. Gautier in France; the British Association Committee in England; Messrs. William

Mar 1, 1905