Search Documents

By D. Harker, E. Epremian

The constitution of the nickel-tungsten system has been studied by a number of investigators, the most recent of which are Ellinger and Sykes.1 On the basis of metallography, electrical resistivity and hardness measurements and some X ray diffraction work, they constructed a consitution diagram (Fig 1). Ellinger and Sykes report a0 for the alpha face-centered cubic phase (nickel saturated with tungsten) as 3.66?.‡ The gamma phase (tungsten saturated with nickel) is given as body-centered cubic, but no value of a. is recorded. At 43 pct tungsten by weight (approximately 20 at. pct) a beta phase is reported, but structure and lattice parameter are not known. Primarily on the basis of metallographic evidence, they conclude that beta is a new phase and rule out the possibility of formation of a superlattice since they- observe a new phase in the microstructure. Grube and Schlecht2 report an ordering reaction in a system similar to the Ni-W (Ni-Mo) and Harker3 has shown that NirMo forms a superlattice upon the pre-existing face-centered cubic lattice of the alpha phase. Elliniger arid Sykes observed a change in the diffraction pattern of a 4.3 pct W alloy upon aging and attributed it to the formation of a new phase. Thus, there appears to be some question as to the character of the beta phase reported by Ellinger and Sykes. The purpose of the present work is to determine precisely the structure and nature of the beta phase in the Ni-w system of X ray diffraction methods. Experimental Procedure One inch diameter ingots of 43.66 pct, 40.15 pct and 34.06 pct .tungsten by weight (19.8, 17.6 and 14.1 at. pct respectively) were melted and cast under vacuum from electrolytic nickel and pure wire filament grade tungsten. The ingots were soaked for 16 hr at 1300°C in a hydrogen atmosphere furnace, then swaged at this temperature and finally drawn to 0.020 in. diam wire. Some of the bar stock was retained in 1/2 in. diam rod for hardness and metallographic studies. Wire samples for diffraction work were sealed in evacuated quartz tubes and subjected to the various solution and aging heat treatments in a hydrogen furnace. X ray photograms were taken in a Debeye-Slierrer camera using copper K radiation filtered by nickel foil. Results X RAY DIFFRACTION The lattice parameters of the alpha and gamma phases at saturation were determined by an X ray photogram of the 19.8 at. pct W alloy after solution heat treatment at a temperature well within the alpha-gamma range above the peritectoid temperature (17 hr at 1150°C—oil quenched). The alpha phase was found to be face-centeted cubic with a. of 3.594 ± 0.001?, while the gamma phase was determined as body-centered cubic with a. of 3.158 ± 0.001?. Exactly the same phases and parameters were ohtained with the 17.6 at. pct W alloy for the same solution heat treatment. Thorough analysis was made of an X ray photogram of a 19.8 at. pct alloy sample in the quenched and aged condition (solution treated 1T hr at

Jan 1, 1950

By W. P. Barba

IN THE early summer of 1917, it became evident that the then existing sources of supply of guns and gun forgings were totally inadequate for the enormous and rapidly growing requirements of the Ordnance Department of the Army, so arrangements were made with sixteen makers of other products to take up the manufacture of guns and gun forgings. Nine of these makers were required to produce their own steel from the raw materials and convert it into rough machined gun forgings; the others finished and assembled these forgings into completed guns. In December, 1914, four of these makers of steel and rough gun forgings were instructed to manufacture the same amount of the 6-in. and 9.5-in. guns and howitzers. It, therefore, seemed practical .and profitable to assemble these makers into a small group, together with the officers of the Ordnance Department, and provide standard 'equipment in each of the four works for the production of these two types of guns. The advantages of this cooperation were immediately manifested, and there commenced an interchange of shop practice and a free discussion of facilities and methods that covered not only the equipment but the manufacturing processes.

Jan 1, 1920

NORTH AMERICA Number Members Alaska 32 Canada 300 Mexico 165 Newfoundland 3 United States Alabama 43 Arizona 121 Arkansas 9 California 674 Colorado 184 Connecticut 94 Delaware 19 District of Columbia 120 Florida 17 Georgia 5 Idaho 66 Illinois 211 Indiana 56 Iowa 8 Kansas 32 Kentucky 31

Jan 1, 1934

By James Douglas

IN discussing the waste upon which hinges, or is supposed to hinge, so largely the preservation of our national resources, the conclusions reached would be more reliable if actual ex¬perience were consulted, and fewer deductions were drawn from general statements, which are often the product of the imagination. It cannot be questioned that the value of by-products has not been sufficiently appreciated by us, and that our, tardiness in recovering the useful ingredients of the escaping gas of our coke-ovens is one of the most glaring instances of shortcoming in that direction. And yet even for that sin there is some palliation in the immature condition of affiliated industries. I presume that it is admitted, without argument, that, except under very exceptional conditions, all the elements cannot be recovered from most of the ores or natural products. which we treat. While it is a shame that the by-products from our coke-ovens should be dissipated, Edward W. Parker's report to the U. S. Geological Survey for 1906' supplies a fairly good excuse in justification of this appalling waste. He says (pp. 773 to 774.)

May 1, 1909

By J. C. Bayles

Jan 1, 1886

By Jose J. Alvarez

INTRODUCTION Three major plant processes control the operation of an uranium in-situ mining plant. The three pro- cesses can be categorized under the headings termed - loading, elution, and precipitation. All other plant processes can be subcategorized under the three. In summary, the major plant processes in an in- situ mining plant are: 1. Loading - The pregnant lixiviant from the production wells flows through anion exchange resin. The loading of the uranium on the resin is controlled by various factors, such as ionic strength, valence, functional groups, etc. 2. Elution - The uranium-loaded resin is eluted or regenerated by a high ionic strength solution. The effluent from this process is de- fined as the pregnant eluate. 3 . Precipitation - The pregnant eluate is chemically treated to attain the ideal conditions for the selective precipitation of uranium. Hydrogen peroxide is an ideal precipitating agent under URI conditions. This paper will focus on two of the major processes: Elution and Precipitation. For the most part this relatively young industry has grasped the theory of liquids in continuous flow for the operation of the plant processes. Likewise, URI initially operated the two processes of interest with the continuous flow concept. Through laboratory experiments, URI has abandoned the flow concept and operates the eluting and precipitating stages with the concept of "batch" processes, whereby only one container, filled to a specified liquid level, is chemically processed. In the proceeding sections, each of the two pro- cesses will be discussed in detail, from their original concept to the present operation. Only minor modifications were made to the existing circuits for the conversion with results revealing a greater level of efficiency. ELUTION The elution of the loaded anion exchange resin can be achieved by different high ionic strength solutions. The selection of constituents is dependent on both chemical and economic considerations (i .e., efficiency and operating/restoration factors). The regenerant presently used is a pH 9.5 solution containing 7.5% NaCl and a mixture of Na2C03/NaHC03. expressed as 2.5% NaHC03.

Jan 1, 1980

By Howard N. Eavenson

AN analysis of the bituminous coal situation by an authority who traces the production, mining, safety, markets and labor trends in comparison with other fuels. BEFORE 1918 the production of coal experienced a steady growth, with slight recessions in ouput in only twelve years (1837, 1841, 1852, 1855, 1861, 1874, 1876, 1889, 1894, 1905, 1909, 1914), and in each of these cases the loss was recovered in the following year and the increase continued. In each decade the output was doubled. Prices, while not high, allowed some profit. In 1918 during World War I, an output of 580 million tons was reached and with the exception of 1923 this total was not again reached until 1942, in World War 11. Losses of output in this period were much greater than ever before; in 1932 the total was 270 million tons less than in 1918 or 1923, and the loss after 1923 was not recovered until 1942. The greatest output was 631 million tons in 1947.

Jan 1, 1950

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The Blast Furnace Studies Section, Metallurgieal Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1940

By Oliver Bololes

UNDER the able leadership of Samuel H. Dolbear, the Committee on Nonmetallic Minerals furnished a program of sixteen papers comprising three sessions. An outstanding accomplishment in technology presented at the first session by Benjamin L. Miller and C. H. Breerwood is the application of flotation to the purification of limestone used in cement manufacture. In place of selective quarrying to provide high-grade raw material, the quarry-run stone is pulverized and treated in froth flotation cells for removal of free silica and mica. Some advantages are cheaper quarrying, more complete utilization of quarry rock, avoidance of purchasing high calcium stone, lower fuel cost and improvement in the finished cement. Paul M. Tyler presented the general subject of milling methods as applied to nonmetal lies. He pointed out the importance of some of the more recent refinements in ore dressing, and urged the need of a wider appreciation of their possibilities. The gypsum industry of Canada was described by L. H. Cole. Crystal growth during the setting process was illustrated by moving pictures. The Coastal Plain and interior salt

Jan 1, 1935

By Evan Just

DIRECT subsidies for mine production in this country began as an outgrowth of wartime 'price regulation. The price-fixing authorities realized that the volume of production to be required from domestic copper, lead, and zinc mines would invoke costs of production considerably higher than the established ceiling prices. Accordingly, beginning Feb. 1, 1942 the Premium Price Plan was set up, which undertook to pay premiums to mines for production in excess of quota, of 5¢ per lb of copper and 2Y4¢ per lb of zinc or lead. Quotas, except for small mines, were initially established at the average rate of production in 1941, but were later reduced arbitrarily on an individual basis. Subsequently, additional "B" premiums were set for lead and zinc of 2Y40 per lb and a further "C" zinc premium of 2%¢. Additional copper premiums were negotiated on an individual basis, mainly with small mines. Quotas under each of these successive categories were the production obtained at the next lower premium level. In other words, under ceiling prices of 12¢ for copper, 6,14¢ for lead, and 83¢ for zinc, it was possible for high-cost operations to receive prices plus premiums of 17¢ or more for copper, 12¢ for lead, and 16% 0 for zinc on a portion of their production. On the other hand, some of the larger operators received only slight premiums and in at least one instance none at all. The average price plus premium for copper was 12.25¢ in 1942 and rose to 13.65¢ in 1945. That for lead was 6.99¢ in 1942 and 8.73¢ in 1945, and for zinc it was 9.06¢ in 1942 and 11.200 in 1945.

Jan 1, 1948

By AIME AIME

IT IS impossible in this short sketch to give a detailed description of each part of the plant at Bethlehem, therefore, only such facts will be touched on as are necessary to give a general idea of the works. The extent of the plant, and the fact that the units making up the various departments are located in different parts of the works, make it impracticable to mention the departments in any regular order with regard to their location. They are, therefore, mentioned approximately in the order of their relation to each other with reference to their functions in the making of the various products.

Jan 1, 1924

By E. V. Daveler, Frank L. Antisell

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface, and the "set," or the decail appearance of the surface of the shape. The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are these characteristics connected that they are often used as synonymous terms by the refiner when he is speaking of well-refined copper. Oxygen is often spoken of as a medicine for copper, it being used to regulate the pitch.

Jan 1, 1920

By Scott Turner

MY YEAR OF SERVICE as president of the A.I.M.E. came at a time when the mineral industry had suffered severely because of disturbed economic conditions throughout the world. The Institute, an integral part of this industry, had been similarly affected. Its membership and revenues decreased; it was confronted by problems of retrenchment at a time when its vigorous operation was especially important to its members, of some moment to the mining industry, and of value to the nation. Throughout the last year, the recession of activity in our industry continued with slight abatement. Your Board accordingly exercised such economy within the Institute as was possible without impairment of essential functions. It endeavored to aid in sustaining the morale of members, their sense of professional unity, and their interest in maintaining research and the interchange of scientific and technologic data upon which the progress of our industry depends. Effort was made to assist in the difficult task of finding employment for needy members; our endeavors have met with some success.

Jan 1, 1933

By Russell Dayton

THE metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concern-ing the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chal-cography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Konigsberger,(1)? in 1909, was the first to apply polarized light to the microscopic study of

Jan 1, 1935

Jan 1, 1902

By H. D. Hoskold

I. Instrument-Parts and Implements. Cross-hairs ; Stadia-measurement; Fineness of Graduation ; Cylindrical Gradu ation ; Nonius; Vernier ; One Vernier or two ; Leveling-Screws ; Troughton & Simms' Shifting Tripod-Head ; Hoskold's Shifting Tripod-Head; Hoskold's Extensible Tripod ; Electric Lamp ; Plumb-lines; Chain. II. Instruments. Compass (Mine-compaes of 1518, Compass of 1541, and Agricolals of 1556, Voig tel's Setz-compass, Circumferentor, Stanley's Hedley Dial, Compass on Tele scope, Hanging Compass, Lack of Precision) ; Plane-table; Octant and Quadrant; Theodolite and Transit (Evolution of the Theodolite, Scott's Tachymeter, Hoskold's Engineer's Theodolite, Angleometer, Precision of Mine-Theodolites). I. Instrument-Parts and Implements. Cross-Hairs.—Mr. Scott‡ says Lean's dial " might also have been provided with a diaphragm and cross-hairs; for Huygene discovered that any object placed in the common focus of the two lenses of a Kepler telescope (1611)- appeared as distinct and well defined as any distant body. Following this established theory, in 1669 Jean Picard, Marquis Malvasia and others crossed silken fibers in the mutual focus of their astronomical instruments." If by this Mr. Scott means that Huygens and Picard first devised and applied cross-hairs to the focus of the telescope, the writer cannot agree with him. Huygens did not describe " his telescope without tubes until 1684, in his Astroscopia Compendiaria."§ Moreover, it is recorded that the English astronomer, Gascoigne,?

Jan 1, 1902

By R. A. Hadfield

It seems a specially fitting opportunity to present a paper on the alloys of iron and aluminum at the New York meeting of this Institute, owing to the fact that America has, more than any other country, originated and developed the manufacture of cheap aluminum. The Cowles, Castner, and Hall systems have all originated in the ever-busy brain of our cousin across the water. The problem of cheaply producing this valuable metal has been a difficult one, but to the writer it seems that the more arduous the task the greater the delight with which our American friend attempts to overcome the difficulties surrounding it, and the more vim he throws into the work. Another and equally striking proof of this is to be found in the recent appearance of the already wellknown remarkable work, The Mefallurgy of Steel, by Mr. H. M. Howe, of the Institute of Technology, Boston, Mass. It is to be hopel that this Institute will not be slow to recognize by some special mark its appreciation of this signally valuable and original work. The writer has been led to describe the following experiments, believing that so far no full and exact report has yet been presented to this Institute as to the effect of aluminum alloyed or combined with the metal iron. It has been a special object to make the material as far as possible a true alloy or combination of aluminum and iron, with as small quantities as possible of other disturbing ingredients, such as silicon, manganese, etc. In the material described in these experiments, the total amounts of other elements present (sulphur and phosphorus being disregarded as present in such small quantities) do not exceed about 0.5 per cent. Such material may therefore be probably taken as fairly illustrative of the effect of the metal aluminum upon iron. Since completing the experiments the writer

Jan 1, 1891

Abbott, Argyle Campbell 1209 Sherwin Ave., Chicago, Ill. Almstrom, Adne A., Student, Met. Engrg., Washington State College Pullman, Wash. Ankudinoff, N., School of Mines, Univ. of Utah Salt Lake Cite, Utah. Apter, Robert F., Student, McGill Univ Montreal, Que., Canada. Bailey, Donald G 798 Kensington Rd., Los Angeles, Cal. Baker, Kenneth B., Met., Aluminum Co. of America Pittsburgh, Pa. Barger, Thomas, Student, Univ. of North Dakota Grand Forks, N. D. Bartholomees, Geo. C Box 304, Bonne Terre, Mo. Bates, Walter, Student, Univ. of Utah, School of Mines Salt Lake Cite, Utah. Bobb, Russell V 16 College Ave., Houghton, Mich. Boswell, John C., Stripping Asst., Fairbanks Exploration Co Fairbanks, Alaska. Brandenburg, E. C., Student, Univ. of Kentucky 112 Church St., Lexington, Ky. Brannen, John, Chemist, Assay Office, Consolidated Min. & Smelt. Co. of Canada, Ltd., Tadanac, B. C., Canada. Brooker, Edgar, Jr., Student, Ferrous Met., Stanford Univ., Stanford University, Cal. Brooking, Leslie E 738 Lakoma, Norman, Okla. Clark, Martin Lester, Student, Missouri School of Mines Rolla, Mo. Collins, Edward D., Jr Box 1597, Ribbing, Minn. Comeau, Faye Bernard, Student, New Mexico State School of Mines Socorro, N. M. Conder, Henry S., Student, Pet. Engrg., College of Min., Univ. of California, Berkeley, Cal. Cotton, John Francis, Metallographist, Stealton Plant, Bethlehem Steel Corp., Steelton. Pa. Dahlgren, Elmer George, Student, Univ. of Wisconsin, Tripp Hall, Madison, Wis. Dale, James L., Student, Colorado School of Mines Golden, Colo. Dashti, Mirza Abdullah Khan, Graduate Student, Columbia School of Mines, Engrg. Chemistry, New York, N. Y. DeHuff, Gilbert L., Jr., Student, Lehigh Univ Bethlehem, Pa. de Romana, Enrique P., Jr. Engr Casilla 22, Arequipa, Peru. Oresbach, Charles Howard, Geol., Gulf Production Co Box 1428, Amarillo, Tex. Evens, Howard G., Student, Michigan College of Min. & Tech Houghton. Mich. Fassler, Glen Emerson Rodman, Inspiration, Ariz. Feight, Charles Donald, Foreman, Clairton By-Product Coke Wks., Carnegie Steel Co., 319 5th St., Wilson, Pa. Floe, Carl F., Student, State College of Washington Pullman, Wash. Fuentes, Vicente, Student, Pet. Engrg., Univ. of Oklahoma, School of Mines, Norman, Okla. Fuhrman, Carl F., Student, New Mexico School of Mines Socorro, N. M. Goergen, Gerald G., Cerro de Pasco Copper Corp Casapalca, Peru. Grove, Hubert A., Training Course, U. S. Aluminum Co New Kensington, Pa. Gastetter, Robert E 1010 N. Cherry Ave., Tucson, Ariz. Halbouty, M. T., Student, Texas Agriculturcl & Mech. College, Box 254, Faculty Exchange, College Station, Tex. Halfast, Edgar 710 E. Okmulgee Ave., Muskogee, Okla. Hall, Robert Lee 121 58th St., Niagara Falls, N. Y. Hanson, Rolf H., Student, Colorado School of Mines Golden, Colo. Hillyer. Shaler G., Student, New Mexico School of Mines Socorro, N. M. Hoertel, Frederick W., Met., R. W. Hunt Co., Engrs St. Louis, Mo. Holtz, Henry G., Student, Ohio State Univ Columbus, Ohio. Hon, Richard J Box 721, Miami, Ariz. Huffman, James O'Neil, Student, College of Min., Univ. of California Berkeley, Cal.

Jan 1, 1929

By Lucius W. Mayer

The iron-mines of the Ilsede Hütte Co. are at a town called Peine, about 20 miles east of the city of Hanover, on the railroad to Brunswick (Braunschweig). Hanover, the capital of the province, is a military city, of approximately 250,000 inhabitants, and Brunswick, 33 miles to the westward, has half this number. The mines here described are located in a hamlet called Bülten. The Ilsede Hütte Co. operates two mines, 1.5 miles apart, in this district, Gruber Bülten Adenstadt and Gruber Lengede Bodenstadt. It also operates an iron-mine north of Hanover, known as Eiserhaven, and one in the Harz mountains, the Georg Friedrich, at Grauhof. At Bülten a coarse conglomerate, a, Figs. 1 and 2, contains nodules of limonite, cemented together by calcium phosphate. The ore contains Fe, 25 to 45; Mn, 3 to 4; P, 0.6 to 1.4; S, 0.02 to 0.09; and CaCO3, 40 per cent. Directly above the conglomerate is limestone, b, followed by a mixture of clay and sand, c. Below the conglomerate is a hard clay floor, d. The ore-body, from 10 to, 12 km. long, and from 3 to 4 km. wide, has a maximum thickness of 20 m. It clips approximately 10° S.E., and strikes N. 45° E. Diamond-drill prospecting shows that the thickness diminishes to 1 m. as the end of the deposit is approached to the northward. At this point the deposit is 250 m. below the surface. In Fig. 2, the arrow, A, indicates the general direction of the work along the face, a, which is carried forward in a straight line for its entire length. At B, a train is approaching, which has come from the bench-track, shown at G, by a circuitous route, and is dumping the overburden behind the face, in the space left by the excavated rock. Formerly the work at this mine was essentially open-cut, the deposit having a very strong outcrop. Figs. 1 and 2 show also

Sep 1, 1908