Search Documents

By P. F. McIntyre

Electrolytic refining of lead was first carried out on a commercial scale at Trail, B. C., in 1903. The capacity at that time was small, and cell-changing operations were managed with chain block and monorail. Development up to 1922, utilizing crane installations and cell additions, attained a production of 100 tons per day. Successive additions from 1922 to 1926 further increased the rated capacity to 396 tons per day. Other improvements in metallurgical practice have gradually increased production, until for the year 1935 it was 448 tons per day. During the first five months of 1936, an average daily production of 504 tons was maintained without increasing the size of the plant. Lead Refinery Buildings.—The tank room and the lead-melting and casting equipment are housed in two buildings, which parallel each other and which for the greater part of their lengths are joined by a connecting aisle. All basements, walls, sumps and floors are of concrete. Where exposed to the electrolyte, the concrete has a protective coating of asphalt (220" melting point) over a coat of asphalt paint as a primer. Buildings erected before 1924 are of wood. More recent additions are made of structural steel with gunite siding. A brick building, adjoining the older section of the tank room, houses the slimes-treatment plant. The power house, containing motor generators, air compressors and rectifiers, is constructed of tile. Cell Construction.—The electrolytic cells are of reinforced concrete lined with asphalt. They are cast in pairs, the outside dimensions of a double cell being 113 in. long by 73 in. wide by 48 in. deep. The bottom is 6 in. thick and the sides, ends and center wall are 4 in. thick. A ledge 3 in. wide and 2½ in. deep is left along the top of the side walls to carry the insulators and bus bars. Reinforcing consists of ½-in. round iron rods. Cell inspection and repair work is done in conjunction with the cell-changing operations. The repair work necessary is usually confined to renewing chipped asphalt, unless a tank has been accidentally broken. Minor concrete repairs can be easily made in place. The broken concrete

Jan 1, 1937

C. W. GENNET, JR.,* Chicago, 111. (written discussion?).-Since the Lehigh Valley accident, transverse fissures have become a source of constant anxiety to railroad officials, because such defects, only infrequently detected by the trackmen, may appear under a moving train entirely without warning. The number of actual accidents resulting from rails containing fissures is no doubt a small proportion of the total, but the serious losses that have been directly attributable to fissures, coupled with the continual possibility of repetition, creates an alarming situation which demands a full investigation of the cause of fissures; apart from other types of rail failures. Mr. Howard's position gives him a field for action and an opportunity for laboratory examination and research that are unsurpassed, and the results. of his investigations must be received with the utmost attention and respect. His admirable paper, summarizing his previously published studies and analyses of the transverse fissure problem, constitutes a convincing treatment of the subject chiefly from the standpoint of stress and strain to which rails are subjected. The intricacies of the problem are so great that seemingly any theory advanced for the cause of fissures may be attacked from some angle; and although Mr. Howard's deductions are logical in the direction followed, it is apparently necessary for considerable work to be done along other lines before his theories can be fully accepted. It is generally conceded that fissures, whether fundamentally clue to fatigue or something else, are of a progressive character, their ultimate size' being the result of growth from an originating nucleus or point of rupture. Abundant proof of this lies in the variable sizes of the fissures found, and there can be no doubt that their development or growth is the result of the strains to which rails are subjected in the track. Obviously, therefore, the most important factor in investigating the cause for fissures lies in determining the conditions that exist at the point or

Jan 4, 1918

THE following paper has been prepared to meet a demand for a concise review of the California oil industry. It is based largely upon information secured during the course of the senior, author's professional activities, and upon data obtained during the course of investigations for the U. S. Geological Survey and the U. S. Bureau of Mines. Considerable information has been obtained from other sources, and to those who by publication or otherwise have contributed, the writers extend their thanks. GENERAL STATEMENT In 1912 the United States produced 63.25 per cent. of the world's production of petroleum, Russia, its nearest competitor, yielding only . about 19 per cent. The production in 1912 reached 222,113,218 barrels (or 29,615,096 metric tons), compared with 220,449,391 barrels in 1911. The average price per barrel in 1912 was nearly 74 c., as against nearly 61 c. in 1911. The total value, therefore, increased 22.20 per cent., or $163,802,334 above the value for the previous year. These figures of production include pipe-line runs, independent railroad shipments, oil piped direct to refineries, and the crude oil consumed as fuel in oil production. The production does not include oil in storage in the field which has not been sold.

Jan 3, 1914

By Walter Herd

FOR the past eight years No. 2 mine of the Cumberland Railway & Coal Co., Springhill, Nova Scotia-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent that some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Department of Nova Scotia requested from the U. S.. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room and pillar method wasp employed and in January of that year (there being a cessation of work from March to August due to labor troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In the interval development work for longwall retreating below the 5900-ft. level was vigorously pushed. This longwall retreating system was suggested by Mr. Rice as a possible remedy and was heartily endorsed by the company officials. This paper describes the conditions and happenings subsequent to Mr. Rice's report and more especially the results with the longwall retreating system of mining under the peculiar circumstances pertaining to mining No. 2 Seam, Springhill, at depth, and records the conclusions which experience with several severe bumps under this mode of extraction would suggest. Except where necessary to make the paper intelligible as an entity any duplication of Mr. Rice's report will be avoided.

Jan 1, 1929

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By R. L. Templin

The increasing use of aluminum and its alloys in commercial fields tias demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure alunlinum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. Comparison oF Cutting Tools Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30" to 50°, making the total angle of the cutting edge of the tool from 35' to 55". A side

By Thomas L. Garwood, F. C. Menk

IT is generally, accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sizes contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uniform bed. With a dusty feed the fines tend to segr6gate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants dedusting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets. DEDUSTING The practice of dedusting, sometimes called aspirating, has presented a problem in disposing of the dust and intermediate small sizes recovered in the process. It has been found that no difficulty is experienced in disposing of the intermediate sizes, since they are free of fine dust and burn freely on grates built for small coal. They handle well, flowing freely from bins and hoppers and into conveyors, and pulverize easily. They have a low angle of repose. In tests made on this size as a feed to coke ovens, the results have been excellent, in that the natural breakdown of .coal in handling and shooting in the mine gives this small-size coal good

Jan 1, 1943

By John Rogers

The goal of a detailed quantitative understanding of the variables insulfide flotation in terms of established, or new, scientific principles is still distant, although there has been a good beginning in the past 50 years with more rapid progress since 1930. Advances have paralleled closely those in other branches of surface chemistry and the development of a series of experimental techniques such as contact angle, surface area measurement, radioactive tracers, infrared spectra, electron diffraction, monolayer, and electro- chemical methods of investigation. The second editions of books by Sutherland and Warkl ( 1955) and Gaudin2 ( 19571, are detailed accounts of this progress. The complexity of sulfide mineral flotation systems is indicated by Sutherland and Warkl who list 32 variables of flotation, of which only 22 can usually be controlled by the metallurgist. A consequence of this multiplicity of variables, many of which may be specific to each particular ore, is that ways of floating sulfide minerals from new ores are still developed empirically. How- ever, this review will try to show how the chemistry of the function of frothers, collectors, depressants, and activators in sulfide flotation is being steadily unravelled. Chiefly, it will be concerned with the interaction of pure soluble compounds with individual sulfide minerals, the surfaces of which are often not stoichiometric for several reasons discussed by Plaksin.3 As a result, for example, a freshly cleaved galena surface has cathodic and anodic areas which have different degrees of oxidation and different reactivity to- wards collectors like xanthate. Such complicating considerations should be remembered in the subsequent discussion of pure minerals. THE NEED FOR FLOTATION REAGENTS After considerable controversy it has been established with a few exceptions that unoxidized, uncontaminated sulfides will not float. Moreover all flotation plants recovering sulfide minerals use collectors which are removed from the circuit with the sulfides. Gaudin, Miaw, and Spedden4 have discussed the relation between the crystal structure of solids and the native floatability of the exceptions mentioned above. A second question which has been much explored is the nature of the surface on which a collector like xanthate is adsorbed or reacts. Is this the un- changed surface of the sulfide mineral, or does the adsorption depend on the initial oxidation of the sulfide surface ? Sutherland and Warkl and Gaudin2 discuss the work of Taggart5 and others on this question without reaching any other conclusion than that oxygen was important.

Jan 1, 1962

By E. Heaton Hemingway

DURING the past year, the Watertown Arsenal has been interested in the occluded gas and oxide content of certain ordnance steels in order to determine, if possible, whether some of the peculiar failures in their physical properties might not be traced to these causes. For the purpose of best accomplishing a study of this nature, it was decided to heat the various samples of steel in a vacuum for definite periods of time at high temperatures and carefully examine the quantity and composition of the gases evolved. By the use of a fused quartz tube fitted with a water-cooled, ground-glass stopper, it was possible to maintain a vacuum at a temperature of 1000° C. for 10 hr. without perceptible leakage being evidenced as measured by a McLeod gage. The silica tube was connected with an evacuating system so constructed that the volatilized gases could be removed from time to time and a low vacuum of 0.002 to 0.0010 mm. of mercury continuously maintained. At no time during the period of heating or in the removal of the gases did the evacuated system come in contact with rubber stoppers or any rubber connections, making contamination from such a source impossible. In other words, the only volatile products that could be obtained must necessarily have come from the steel itself or from the glass and fused quartz system or from the mercury used as a sealing agent. In the earlier experiments, the steel treated was in the form of turnings, but this practice was discarded because the weights of the turnings before and after being heated were widely inconsistent, even when taken from the same piece of steel. This discrepancy developed largely through variation in the amount of metal volatilized with the gases; this metal could always be seen in the form of a ring where it condensed in the cooler portion of the tube either in the amorphous or crystalline condition. Because of the frequency in occurrence and the variation in the manner of deposition, this material was roughly analyzed and found to consist for the most part of iron. At the same time two samples of steel that had been

Jan 8, 1920

By S. J. Aresco, George E. Keller, J. Visman

INTRODUCTION The accurate sampling of coal, as with most minerals, is a difficult task. Coal is a very heterogeneous material made up of different types of coal and varying amounts of mineral matter. The product as mined may contain all of the layers of coal and impurities found in the seam as well as portions of the strata above and below the coal seam. The preparation plant is the device to size, crush and/or remove impurities so that the coal may be shipped as a saleable product. Sampling may be needed at many stages in the preparation process. Although this chapter is mainly concerned with sampling in connection with preparation processes, the principles will apply to all coal sampling. The main reasons for sampling in connection with coal preparation are: 1. To determine the washability characteristics of the raw coal by means of float and sink tests. These may be used for the design of a preparation plant, prediction of results to be obtained or for monitoring raw coal delivered to the plant. 2. To check the performance of various operating units in the plant, either by float and sink tests or chemical analyses. 3. To determine the analytical characteristics of the products produced, such as moisture, ash, Btu, sulfur, etc. HISTORY The earliest accepted methods of sampling coal in the United States were given in U. S. Bureau of Mines publications by J. A. Holmes,1 G. S. Pope2 and A. C. Fieldner.3 The American Society for Testing and Materials more or less adopted the methods proposed by the U.S. Bureau of Mines in their Standard D-21-1916, and it remained a standard for many years. Briefly, the standard called for a 500 pound sample for coals less than. 3/4 -in. in size and a 1,000 pound sample for all coals over ?4 -in. in size. No mention was made of increments but there was an instruction that the sample should spread over the coal to be sampled. Sample preparation was by hand crushing with the alternate shovel method for reduction to 250 pounds followed by coning and quartering below 250 pounds. Obviously, with the amount of work involved, this method of sample preparation was rarely followed. This method of preparation resulted in samples that were practically air dried because of long exposure while crushing, shoveling and quartering. In the late nineteen twenties and early nineteen thirties, studies for more practical methods were begun. Dr. E. S. Grummell4, Imperial Chemical Industries, Ltd, London, summarized the work to date at the

Jan 1, 1968

By J. W. Spretnak, H. R. Ogden, A. G. Imgram

The effect of working reduction, stress-relief annealing, and recrystallized grain size on the tensile and notch-tensile properties of molybdenum and Mo-0.5 Ti was studied. It was found that increasing the amount of working reduction increased the strength and reduced the tendencies toward brittle behavior. Stress -relief annealing did not alter the strength but lowered the transition temperature. Increasing the recrystallized grain size lowered the strength and raised the transition temperature. The notch -unnotch strength ratio began to decrease with decreasing temperature at temperatures below those at which the notched ductility fell to zero for all of the micro structural conditions investigated. BEING bcc metals, the refractory metals in Groups Va and VIa (V, Cb, Ta, and Cr, Mo, W) undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures. Previous research has shown that molybdenum and tungsten not only have higher transition temperatures than columbium and tantalum but show a marked sensitivity of transition temperature to structure as well.' Recrystallized materials become brittle at considerably higher temperatures than is the case with material having a worked or fibered micro-structure. Evidence of structure sensitivity has also been detected in columbium- and tantalum-base alloys containing appreciable amounts of molybdenum or tungsten such as F-48 (Cb-15W-5Mo-1Zr) and Ta-10w.2 This paper describes the results of research conducted to further evaluate the effects of metal. lurgical structure on the low-temperature tensile and notch-tensile properties of molybdenum and Mo-0.5Ti. The effects of rolling reduction, stress-relief annealing temperature, and recrystallized grain size were studied. Considerable progress has been made in explaining the fundamental mechanisms of the flow and fracture characteristics of bcc metals. Several of these concepts are helpful in interpreting the data obtained in this study. Brittle fractures occur when the highly temperature-sensitive yield strength equals, or exceeds, the temperature-insensitive brittle cleavage fracture stress.3 The rapid increase in yield strength with decreasing temperature, characteristic of all bcc metals, is therefore of primary concern. petch4 has described the yield strength, ay, (stress required to initiate plastic flow) of bcc metals by the expression where ai is the frictional resistance to slip, Ky is a constant numerically equal to the slope of a a vs curve, and 2d is the average grain diamefer. The oi term itself is thought to be composed of a temperature-insensitive component dependent on impurity content and second-phase particles and a temperature-sensitive component dependent on the Pierls-Nabarro force.5 This equation has also been demonstrated to hold for the flow stress (stress required to maintain continued plastic flow).' Brittle-crack nucleation is thought to occur by the coalescence of dislocations piled up in slip planes at sessile dislocations or twin and grain boundaries.7,8 These proposed mechanisms require that a large number of dislocations be released into the active slip planes so that sufficiently large stress concentrations are produced at the dislocation pile-ups to enable coalescence into a micro-crack. Therefore, at least a microscopic amount of slip must occur in some grains to facilitate initial crack formation. Cottrell 7 has predicted that brittle fracture, nucleated by slip, should occur when where ty is the shear yield strength, ß = 1 in un- notched xension, u is the shear modulus, and y is the effective surface energy. This equation incorporates the Griffith concept of fracture that a crack will propagate if the decrease in strain energy equals or exceeds the increase in surface energy.

Jan 1, 1964

By M. Cohen

THERE seems to be a natural urge for the human mind to wonder about the beginning of things. When an explosion occurs, we immediately inquire "what set it off?" If a person contracts a disease, we are likely to ask "how did it happen?" On a much loftier plane, when we reflect about the universe, there is the inevitable question "what, or rather Who, started it all?" In principle, these varied queries have at least one attribute in common: they are attempts, whether earnest or casual, to search out the origin of events in nature. Accordingly, they involve not only scientific, but philosophical and even re1igious matters of deep concern. It is evident that, in a broad sense, the phenomenon of nucleation is enmeshed in this enticing concept of "the beginning", but we must extract the scientific component of the problem for our present purposes. Nucleation, as in the case of phase transformations, is best regarded from the standpoint of kinetics. There are then two main steps, which may come in either order: (a) Experimentally, one attempts to measure the frequency with which transformation centers spring into existence; and (b) theoretically, one seeks a model that will account for this observed birth-rate. Temperature, composition, strain, and prior history are some of the important variables that must be considered both experimentally and theoretically when dealing with nucleation in the solid state. Such interaction of theory and observation is an integral part of science in general, but it is particularly significant in the nucleation problem because the very beginning of a phenomenon invariably occurs on too localized a scale in both space and time to be detected with available techniques. Thus, there is little hope of making direct measurements on the nucleus during its birth or to ascertain the exact nature of the process; one can only infer the details of nucleation from the model whose predicted behavior seems to harmonize best with the measured rate of nucleation and its dependence on known parameters. In the field of solid-state nucleation, both theory and experiment call for much ingenuity, but somehow the conceptual schemes have spawned faster than they can be tested by observation. This is not to say that there are many basically new ideas in modern nucleation theory; rather, as we shall see, it is because the required fine-scale measurements are of immense technical difficulty. Quite likely, some of the nucleation models existent today have survived only because of the latitude permitted by meager data. There is great need to bring theory and experiment into better balance in this important area of physical metallurgy. Although one can

Jan 1, 1959

The writing that is effective is woven with a he texture into an agreeable pattern; it is free from knots, loose threads, and stray fluff. The instrument that weaves this literary fabric, whether it produce a homely sock or a lordly tapestry, a simple story or a learned treatise, is a disciplined intelligence, as sure as a steel needle, as precise as a swift loom. The simile breaks down at this point, for the product of the pen is instinct with the human spirit and therefore transcends in beauty anything made by a mere machine. If words are to be woven into eloquent meaning, they must be well knit. Upon the relation of words to each other and of groups of words to other groups, known as phrases, clauses, and sentences, depends the success of writing as a means of transmitting thought from man to man. To be understood beyond question, you should know not only what your words denote' but how to build your sentences; you must not only choose your words aright but construct your sentences properly. A sentence is a combination of words that makes complete sense; it says something about something. A clause is a subordinate sentence or a sentence within a sentence. A phrase is a group of words without a predicate; it makes sense, but not complete sense. For example: I shall wait for a few minutes before I go home. The whole statement is a sentence; "I shall wait" and "before I go home" are clauses; "for a few minutes" is an adverbial phrase. The orderly arranging of words and of combinations of words is called 'syntax'; and from the original Greek form, [s?ta???] (suntaxis), is derived the Greek name for an editor,

Jan 1, 1931

By G. S. Scott, H. G. Turner, W. L. Kleene

It is well known that different forms of carbon show differences in chemical behavior under apparently identical conditions. It is fairly well known that these differences persist, although to a lesser degree, in a single group of carbons, such as the anthracites of Pennsylvania. It is the purpose of this paper to show the extent of these variations for Pennsylvania anthracites from actual quantitative measurements of the amount of carbon dioxide reduced under the standardized test conditions employed. As the amount of carbon dioxide reduced to the monoxide (under comparative conditions termed, for convenience, the "reactivity") is important in combustion, gas production and metallurgy, it is hoped that this paper will be a useful contribution to the store of knowledge on these subjects. In carrying out the investigation, considerable time and thought were spent in obtaining what seemed to be the best possible design of apparatus. The next step consisted in making a number of trial runs on the same sample, varying temperature, particle diameter, etc. and then outlining a standardized procedure to be followed in testing all samples. Fifty anthracites were tested. As a matter of interest, some 10 miscellaneous samples were also tested. The data show initial reaction temperatures (abbreviated I.R.T.), reaction velocity constants at 900" and 950" C., some effects of added substances, and a few additional tests designed to throw some light on the causes of differences in reactivity. The sample of charcoal, as was anticipated, proved to be easily the most reactive of any sample tested. The anthracites as a group came second. The five samples of gas and by-product cokes, obtained from five different coke manufacturers, came third, and a single sample of Rhode Island anthracite ranked fourth, with respect to reactivity as above defined. Although the five coke samples do not necessarily represent the average market coke, and five samples constitute a rather small number of samples to serve as a basis for comparisons, the fact that none

Jan 1, 1934

By F. V. Greene

This paper is based on my experience in the use of asphalt, for paving and other purposes, during the last ten years, part of the

Jan 1, 1889

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to begin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTURES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, depending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1951

By A. M. Gaudin

A GREAT number of hypotheses has been advanced to explain the complex phenomena that are encountered in flotation. In the days of bulk-oil flotation, when a large quantity of oil was employed, it was observed that the oil-mineral aggregate floated above the ore-pulp because of its lesser density. With the advent of froth-flotation this phase of the theory had to be modified to take into account the presence of air bubbles. The reason why the mineral-bearing froth of today rises to the top of flotation cells is, of course, because the air-mineral aggregate, with whatever reagent may be associated with it, is lighter than the pulp. In an attempt to explain froth-flotation the fact has been emphasized that certain minerals are wetted and therefore remain in water; while others are not wetted and therefore become associated in preference with air. Such an "explanation" does not explain facts, it merely states them; for instance, it does not explain why minerals are wetted under some circumstances and not wetted under others. Going somewhat further, the wetting or nonwetting of minerals by water has been ascribed' to differences in the angles of contact between oil droplets and mineral surface at the surface of the minerals. This explanation, however, was abandoned when soluble flotation reagents came to replace the so-called "insoluble" reagents. Another theory, sponsored about 10 years ago by Ralston,2 involves the effects of electric charges at the surface of the minerals particles and air bubbles. This theory, unfortunately, was not developed as fully as it seems desirable.

Jan 1, 1927

By Sir Robert Hadfield

LAST year this Institute was good enough to accept some remarks by the writer regarding sound steel, entitled Plant for Hadfield Method of Producing Sound Steel Ingots, being a continuation of a research in which for some time the writer has been engaged, and full particulars of which were submitted in papers entitled A New Method of Revealing Segregation in Steel Ingots, and Method of Producing Sound Ingots, read before the Iron and Steel Institute in October, 1912. These papers gave rise to a very interesting discussion, both in England and America. This question is one of vital importance, as unless sound steel in the form of ingots is first obtained, sound steel in the finished forms of rail billets, rails, bars, sheets, and other forms cannot be expected. The working stresses demanded by modern conditions are so great, each year they probably approach nearer to the limit of safety, that without doubt those who produce steel will be compelled to pay the attention which this subject deserves. Moreover, the problem is not an insuperable one, as shown by the writer in the papers above referred to. In view of the information which has already been presented in these papers, it is not now necessary to go into details of the system advocated by the writer, except to repeat that the ingots and steel now referred to were produced by employing in the first place sound fluid steel, free from blowholes, this being poured into ordinary ingot molds, provided with the necessary feeding heads, the insulating slag medium, also charcoal and air blast or other suitable form of applying heat to the head portion of the ingot. Tile upper or head portion of the ingot is kept fluid by the intense heat generated by the air blast and charcoal, so that such fluid steel passes into the body of the ingot below the head, thus feeding and avoiding the shrinkage or piping which would otherwise occur. The result is the production of a sound steel ingot, free from blowholes, segregation and piping, and in which the waste portion, usually termed the discard, is but little over 7 or 8 per cent.

Jan 4, 1914

By W. Crafts, J. L. Lamont

Secondary hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to thc secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at II00 F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader. Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to IIOOOF, but the mechanism of the process has received little consideration.

Jan 1, 1949