Search Documents

By B. C. Blake

IN general, billet-type or long slender ingots are used when it is desired to produce directly from the ingot in one conversion a product of medium or small cross-sectional area. They are designed to eliminate the blooming and billet-mill stages of the usual procedure. As used at Connors, they constitute a means of keeping a continuous rolling mill busy in the production of high-quality small rods, small angles, hoop stock, baling ties and concrete reinforcing rods without the need for a blooming or billet mill. They represent sound steel with the best surface that is commercially practical to use in the rolling of small continuous mill products.

Jan 1, 1947

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,' and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6'7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.' EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.' Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

By G. Thodos, W. F. Stevens

The point-source function introduced by Horner' us a solution to the general unsteady-state equation for the flow of fluids through porous media has been utilized to calculate pressure profiles for adjacent wells as a function of time. By trial and error, the time at which the pressure waves meet to cause interference can then be calculated. For this calculation, the time of interference is arbitrarily defined as that time when both pressure waves exhibit a pressure decrease of 25 psi ar the same point within the formation. To illustrate the method, an example involving two adjacent wells producing at different rates has been worked out and is presented in detail. INTRODUCTION The initiation of production of a new well is usually accompanied by pressure drawdown measurements in order to establish the extent and characteristics of the formation. The interpretation of such pressure drawdown data is based on mathematical developments involving a single well in an infinite reservoir. If more than one well is present in a reservoir, the possibility of interaction between wells exists. Therefore, care must be taken in interpreting the pressure drawdown data. It becomes important to be able to determine when this interaction, or interference, becomes significant. This paper presents a method for the prediction of the approximate time of interference between two such adjacent wells. The basic differential equation describing the pressure distribution existing during unsteady-state flow of a slightly compressible fluid has been solved by Hor-ner.' for a constant production rate from a circular homogeneous reservoir of infinite extent. The solution utilizes the point-source function to define the pressure at various points within the formation as a function of time. The resulting expression is: q = production rate, STB/D ,;= formation volume factor, dimension-less µ = fluid viscosity, cp k = formation permeability. md H = formation thickness, ft C - fluid compressibility, psi' F = formation porosity, dimensionless R = distance from centerline of well, ft T = production time, hours Ei(—u) = Ei-function of U Eq. 1 may be used to calculate the pressure profiles generated during production from a single well in an infinite reservoir.

The Candelaria deposit was first discovered by Spanish prospectors in 1863; but its silver ore was not exploited on a large scale until 1873, when the Northern Belle mine was opened. The first Northern Belle mill was built at Belleville, 13 km (8 miles) to the northwest. From 1876 to 1886 the Northern Belle paid over $1 million in dividends each year. In 1882 a 43 km (27 miles) pipeline was built to Candelaria from the White Mountains to the west to furnish water for the mills and town at Candelaria; it was 100 mm (4 in.) in diameter, hand- riveted, and made in England. Sections of this pipe are used. as claim posts today. At its terminus at Metallic City, above Candelaria, a large concrete reservoir was built and called Metallic Lake. It is being used today by Candelaria Partners. Production at Candelaria declined after the mid-1980s, revived for a short period in the early 1890s, and during the 1920s a 300 ton mill operated for three years. Candelaria Partners is owned jointly by Occidental Minerals and Congdon and Carey, with Occidental being the operator. An engineering study done in mid-1979 resulted in engineering for the plant commencing in late that year and heap leaching being started in September 1980. Two million tons of ore per year containing 108 g Ag and 0.28 g Au per mt (3.15 oz Ag and 0.008 oz Au per st) will be mined from the Lucky Hill and Mount Diablo .areas about 1.6 km (1 mile) up Pickhandle gulch from the heap leaching operation. Waste -to -ore ratio is about 2:l. Ore is mined by front-end loaders and hauled by 85 ton trucks to the primary crusher, a 1,070 by 1,780 mm (42 by 70 in. ) gyratory. Primary crushed ore is conveyed to a stockpile of 10,000 tons live capacity from which it is reclaimed by hydraulic reciprocating feeders and conveyed to the crushing and agglomeration facility. This unit is composed of a 1.8 m by 2.6. m (6 ft by 12 ft) double deck screen, a 2.1 m (7 ft) standard cone crusher, and three conveyors. At the conveyor transfer points NaOH and NaCN solution is sprayed on the ore as it falls through a row of 75 mm (3 in.) hanging steel bars. During this process of turning and dividing the ore, the fines agglomerate with the coarse ore to give better percolation for the leach solution on the heaps. Provision was made for the later addition of 2 kg per mt (4 lb per st) of cement to aid in the agglomeration. Agglomerated ore at minus 50 mm (2 in.) size is then conveyed to a 390 mt (430 st) loadout bin where it is transferred to 85 ton rear dump trucks for haulage to the leach pads.

Jan 1, 1981

26. G. H. S. Price, S. V. Williams, and G. J.O. Garrard: Heavy alloy, its production. properties and uses. Metal Industry (1941) 599 354s 372. 394. 27. R. Kieffer and W. Hotop: p. 320 of ref 12. 28. F. R. Hensel. E. I. Larsen, and E. F. Swazy: Physical properties of metal compositions with a refractory metal base. Chap. 42, 483, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 29. R. Kieffer and W. Hotop: p. 290 of ref. 12. 30. H. Freundlich: Kapillarchemie. 211 (1923) Leipzig. 31. W. Ostwald: Zisch. f. Phys. Chemie. (1900) 34, 503. 32. G. A. Hulett: Zisch. f. Phys. Chemie. (1901) 37. 385; and (1904) 47, 357. 33. J C. Chaston: Discussion to Price, Smithells and Williams, p. 257 of ref. 4. 34. W. Dawihl: Untersuchungen ueber die Vorgaenge bei der Abnuetzung von Hartmetallwerkzeugen. Ztsch. f. techn. Phys. (1940) 21 336. 35. W. Dawihl and J. Hinnueber: Ueber den Aufbau der Hartmetallegierungen. Kol-loidzlsch. (1943) 104, 233. 36. F. Skaupy: Dispersoidchemische und verwandte Gesichtspunkte bei Sinter-hartmetallen. Kolloidzlsch. (1942) 98, 92; and (1943) 102, 269. 37. F. C. Kellcy: Cemented tantalum car- bide tools. Trans. ASST (1932) 19, 233. 38. E. W. Engle: Cemented carbides. Chap. 39, 436, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 39. W. Dawihl: Zlsch. f. Melallkunde. (1940) 32, 320. 40. P. M. McKenna: Tool Materials (Ce- mented Carbides). Chap. 40. 454. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 41. G. A. Meerson. G. L. Sverev, B. Y. Osinovskaja: Zhurnal Prikladnoi Khimii. (1930) 139 66. 42. A. G. Metcalfe: The mutual solid solubility of Tunesten Carbide and Titanium carbide- Metal Trealmenl (1946) 13, 127. 43. P. Schwarzkopf: Powder Metallurgy. 196-201 and 354-356 (1947) New York. 44. H. Burden: The manipulation and sintering of hard-metals. Special Rep. No. 38, p. 78. Iron and Steel Inst.. 1947. London. 45. W. D. Jones: Principles of powder metal- lurgy. 150. (1937) London. 46. J. E. Drapeau: Sintering of powdered copper-tin mixtures. Chap. 32. 332, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 47. H. E. Hall: Sintering of copper and tin powder. Metals and Alloys (1939) 10, 297. 48. F. Sauerwald: Present status of powder metallurgy. -.Melallwirlschafl. (1941) 20, 649. 671. 49. H. L. Wain: Powder metallurgy; influence of some processing variables on the properties of sintered bronze. Report ACA-25. Australian Council for Aeronautics (1946) Melbourne. 50. S. L. Hoyt: Constitution of copper-tin alloys. Metals Handhook, 1364. (1939) Cleveland. 51. T. Ishikawa: Studies on the interdiffusion of copper, tin and graphite powders. Nippon Kinzoku Gakkai-Si (1937) I, 226. 52. A. Carter and A. G. Metcalfe. The struc- ture of porous bronze bearings. Special Rep. No. 38, p. 99. Iron and Stecl Inst. (1947) London. 53. R. P. Koehring: Sintering atmospheres for production purposes. Chap. 25, 278. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 54. C. G. Goetzel: Some properties of sintcred and hotpressed copper tin compacts. Trans. AIME (1945) 161, 569. 55. J. W. Lennox: The production of some non ferrous engineering components by powder metallurgy. Special Rep. No. 38. p. 174. Iron and Steel Inst., 1947, London. . P. Duwez and H. E. Martens: The power metallurgy of porous metals and alloys having a controlled porosity. TP 2343, Metals Tech. April 1948. This volume. p. 848. 57. E. A. Owen and L. Pickup: X-ray study of the interdiffusion of copper and zinc. Proc. Royal Soc., London, Series A. (1935) 149, 283. 58. C. G. Goetzel: Sintered and hotpressed compacts of copper-zinc powder. Chap. 34. 352, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 98, R. Chadwick. E. R. Broadfield, and S. F. Pugh: Observations on the pressing. sintering, and properties of iron-copper powder mixtures. Special Rep. No. 38, p. 151, Iron and Steel Inst. (1947) London. 60. A. Squire: The properties of iron-copper compacts. Watertown Arsenal Lab. Rep. WAL No. 67101. 61. F. C. Kelley: Properties of sintered iron- comer uowder. Iron Age (Aug. 15. 193) 158 57. 62. G. H. Howe: Sinterinn of Alnico. Iron Age (Jan. 11. 1940) 14.5, 27. 63. R. Kieffer and W. Hotop: p. 359 of ref. 12. 64. W. Hotop: Permanent magnets from sintered iron-nickel-aluminum. Stahl und Eisen (1941) 61, 1105. 65. P. R. Kalischer: Some experiments in the production of aluminum-nickel-iron alloys by powder metallurgy. Trans. AIME (1941) 145, 369. 66. S. J. Garvin: Production of sintered per- manent magnets. Special Rep. NO. 38. p. 67. Iron and Steel Inst. 1947, London. 67. F. C. Kelley: Discussion to P. R. Kalischer. p. 375 of ref. 65. 68. R. Kieffer and W. Hotop: p. 357 of ret, 12. 69. C. H. Howe: Sintered alnico. Chapter 48, 530, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. Powder Metallurgy Seminar (C. G. Goetzel presiding) C. G. Goetzel—The seminar has been opened by a man who has been active in the field for over fourteen years and has made, since then, some major contributions to the advancement of the art. After having been associated with the Moraine Products Division of General Motors Corporation for over ten

Jan 1, 1949

Jan 1, 1970

Jan 1, 1967

By A. C. Fieldner, W. A. Selvig

For purposes of coal classification it is desirable to know the composition and calorific value of the pure coal substance; that is, of the coal free from its ash-forming minerals. Two methods suggest themselves: (1) To free the coal from most of the ash-forming material previous to the analysis; and (2) to analyze the coal as received and calculate the analysis, with certain more or less arbitrary corrections, to the pure-coal basis. Calculation methods are obviously more apt to give correct results with low-ash than high-ash coals. With coals of unusually high ash it would appear preferable to remove, previous to the analysis, as much of the inorganic matter as possible, by float-and-sink or acid-treating methods. Effect of Ignition on Inorganic Constituents of Coal The need of corrections in calculating analysis to the pure-coal basis is due to the fact that the ash, as determined by ignition, is not the same, in either weight or composition, as the inorganic mineral matter in the coal. On ignition a number of changes occur in the coal such as loss of water of hydration of the shaly material, conversion of pyrite (FeS2) to ferric oxide (Fe203) with evolution of the sulfur as sulfur dioxide or possible fixation of more or less of the sulfur in the ash as calcium sulfate (CaSO4), and decomposition of calcite (CaC03) to calcium oxide (CaO). The amount of sulfur from pyrite which remains in the ash as calcium sulfate depends on the amount of calcite and pyrite in the coal. Certain coals high in both calcite and pyrite show relatively large amounts of sulfate sulfur in the coal ash. The determination of total carbon and hydrogen in coal includes, besides the organic carbon and hydrogen, the carbon of inorganic carbonates such as calcite, and the hydrogen of the water of composition of some of the ash-forming minerals. For detailed discussion of corrections proposed for calculations of coal analyses to the " pure "

Jan 1, 1930

By O. U. Bradley

THE extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, somelosses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. , Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 13 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of. 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause, more or less deterioration in quality, particularly when the fresh production is run direct from the. gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks.

Jan 7, 1918

By Junichi Sato, Takash Suzuki, Tatsuo Imamura, Mamoru Hojo

INTRODUCTION Hitachi Refinery of Nippon Mining Co., Ltd. was constructed in 1911. The refinery began early to recover by-product metals and to manufacture copper products. Today, the refinery recovers gold, silver, selenium, platinum and palladium as by-products of the copper refining process and manufactures copper powder, copper foil, wire bars and chemicals for plating. In 1969, the capacity of the Hitachi Refinery reached 6,000 tons/month. (T/M). Because, at that time, the forecast was for the demand for copper in Japan to increase, planning for the expansion of the Hitachi and Saganoseki refineries was begun. A new 10,000 T/M capacity tank house, a new electrolyte purification plant and a enlarged anode slime treatment plant were planned for the Hitachi Refinery. Construction at the Hitachi Refinery began in December, 1970, and was completed in April, 1974. The development of new machines and processes has resulted in an efficient refinery with a production capacity of 16,000 TIM. This paper is a report on the new anode slime treatment plant at the Hitachi Refinery, and especially on the copper removal process in that plant, the Ferric Leaching Process.

Jan 1, 1976

By L. F. Reinartz

ANOTHER year has rolled by. We are twelve months further away from the start of the depression and. therefore that much nearer to recovery. The accumulated needs and wants 'of our lame, virile population are ready to burst their bonds as soon as confidence returns and credit is stabilized. The steel industry has been harassed by uncertainty of the Government's attitude toward organized labor's de¬mands, and irregularity in volume of production. Steel labor, if left to its own devices, would in most instances, march shoulder to shoulder with the management of steel plants in their effort to pull the industry nut of the ?red.? Cooperation between management and men has improved considerably during; the year.

Jan 1, 1935

By Lewis Robert M.

The importance of phosphate in feeding the people of the world has been recognized by mining companies as they continue their search for new ore deposits and ways of improving phosphate production. An extensive phosphate-recovery research project involving investigation of beneficiation variables by batch testing, flotation pilot-plant processing of the major portion of the ore, gravity separation of the coarse fraction, and recovery of byproduct heavy minerals of a North Carolina phosphate deposit has been completed. Data obtained through batch tests enabled the development of an economical flowsheet which proved successful for the efficient recovery of a good quality phosphate concentrate in a pilot plant.

Jan 1, 1975

By Euzebio De Oliveira

ONE of a recent batch of samples from the Serra da Baliza, in the state of Parana, Brazil, contained asphalt and a dark heavy oil; and workmen on the railway from Porto União to Uruguay discovered asphalt, coming from eruptives that outcrop along the Rio de Peixe. The occurrence f asphalt in the triassic eruptives of southern Brazil, however, has been known a long time, according to Dr. Gonzaga de Campos. It is generally believed that the Botacatú sandstone is always a hard vitrified rock, from the metamorphic action f. the overflowing eruptive contacts. In this region, however, the contact metamorphism is almost nil; the sandstone is slightly hardened in a narrow zone about 20 to 30 cm. wide. In many places, the sandstone is so friable as to be easily reduced to sand, which is used-.in, mortar for building in Guara-puava and Palmas. South and west from Porto União,. this bench of sandstone is about. 50 m. thick, and is capped by a heavy bed. f basic eruptives, many of which are amygdaloids. Dr. Geo: P. Merrill, after studying the triassic eruptives collected by the Coal Commission, reached the conclusion that. "All these rocks are of typical basalt-diabases, not in any essential different other than in structure. An interesting mineralogical phase is its paucity in olivine, which in many cases is completely lacking. Professor Hussak, who carefully studied these rocks and their accessory minerals, decided that in the dikes they are granular (diabase) and, that in the lava sheets, porphyritic (augite-porphyrite or melaphyre), and that the latter pass evidently to normal diabases and are always typical of effusive rocks. The examination f many slides from dikes and sheets leads us to adopt the opinion of Professor Hussak; the rocks of the dikes are of ophitic structure, while that of the sheets show a great variety f structure and may vary from almost granular to basaltic. The great paucity in olivine had been noted by Hussak, who classes as melaphyres, the porphyritic triassic rocks in Brazil which contain olivine.

Jan 4, 1921

By E. J. KENNEDY

FEBRUARY 15-18 will be the outstanding dates of the month for members of the A. I. M. E., for then the 141st Meeting of the Institute is to be held in the Engineering Societies Building, at New York. What with 41 technical sessions, the Annual Business Meeting at 4 o'clock Tuesday afternoon,, two sessions of the Section and Division delegates, minor committee meetings, and the many luncheons and dinners, the Dinner-Smoker, Informal Dance, President's Reception and the Dinner-Dance, the opportunity will be limited to do- more-than cast sheep's eyes at New York's other multitudinous attrac¬tions until the meeting is over. The technical program is diverse but well organized. The sessions are almost equally divided among the four days, with ten on Monday, Tuesday, and Wednesday, and 11 on Thursday. The meeting opens Monday morning with registration. Be sure to attend to this detail. Failure to do so may have its repercussions at the meeting and throughout the year.

Jan 1, 1932

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.'s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952

By C. G. Goetzel

E. V. Crane.*—I want to ask Dr. Goetzel concerning the control of atmosphere in heating and pressing. Was the heating and pressing done in the die, or were the two kept separate there? C. G. Goetzel.—The setup used for this investigation implied heating the die to the temperature at which the work was to proceed, introducing a preformed compact into the hot die. The atmosphere was supplied through an annular chamber from which it passed through two holes into the die cavity. E. V. CRane.—The compact was not preheated? C. G. Goetzel.—The compact was not preheated. Tee Chairman.—In the course of recent studies on the effect of time of heating upon the tensile strength and hardness, I have observed that there is often a maximum in tensile strength and hardness reached before complete homogenization has been attained. The magnitude of each mechanical Property changes rapidly with time in the early stages of sintering, the more so as temperature increases. For these reasons it seems that the comparison of values obtained by heating for the same time at a series of temperatures may be deceptive. Not only may those heated at higher temperatures give higher tensile readings, but the reverse may be true if the maximum in the tensile strength versus time curve has been passed. A better basis for comparison would be that of equal degree of diffusion. C' " Goetzel.—Thank you, Professor Rhines, for this interesting contribution. I would like to add here that I have noticed a similar effect with straight copper. There is, of course, the possibility that this maximum in hardness and tensile strength may be caused by work-hardening.

Jan 1, 1945

By Thomas A. Wright

No symposium on die casting could be complete without consideration of the methods of formula and impurity control. No consideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. COMPOSITION Aluminum.-Aluminum die castings are expected to conform to the specifications of the American Society for Testing Materials1† and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven

Jan 1, 1935

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935