Search Documents

By AIME AIME

THE papers presented at the geophysics session" on Feb. 17 were concerned largely with three aspects of the science. The first ones dealt with the transmission of elastic waves through the earth, then electrical methods came in for their share of attention and finally, the question of the teaching of geo- physics came up for the first time at these meetings. Also, for the first time, there was a symposium of mining men on the practical value of the new science. The paper (T. P. 267) entitled "Seismic Propagation Paths" was presented by Donald C. Barton in the absence of the authors. It dealt with an investigation of the speed of propagation of seismic waves. The latter travel in a straight line when proceeding at a constant velocity, but if the velocity increases at increasing depths, the line of travel becomes a curve. Under the assumption of the authors this curve is found to be the arc of a circle, and their paper gives calculations for reflected and refracted wave paths under these circumstances.

Jan 1, 1930

By L. D. Fetterolf

The New Jersey Zinc Zompany operates at Depue, Illinois, an integrated zinc smelting plant using tie vertical retort reduction process. The overall operation comprises green concentrate roasting, sintering, vertical retort smelting and metal refining. In the roasting operation, the fine concentrate is pelletized, the dried pellets fluidized and autogenously roasted with air in a “fluid column” with minimal formation of dust requiring recirculation. The roasted pellets and any associated roaster dust are agglomerated in a rotating drum and laid down, in combination with coal for fuel, on a Dwight-Lloyd sintering machine which converts to a semi-fused mass - a physical state more suitable for vertical retort smelting. The smeltins plant of 27 vertical retorts rated at 8 T zinc each per day on average requires the following major processing steps - mix preparation and briquettine, briquet coking, vertical retort reduction, vapor condensation and slab casting of metal. A portion of zinc production is converted to 99.99+ percent purity by boiling and fractional distillation in columns consisting of externally heated, superimposed trays of high-conductivity refractory.

Jan 1, 1970

By H. L. Barr

THE following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geol-ogists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions.

Jan 1, 1940

By Louis V. Bender

THIS paper gives a short review of the installation for and the use of gas, as a. fuel, at the Anaconda Reduction Works of the Anaconda Copper Mining Co. Before putting in gas tile fuels used were pulverized coal, lump coal, coke distillate and oil. These fuels are now almost entirely eliminated. For nearly fifty years bituminous coals from Wyoming and Montana fields had been used. These coals were of a good grade, analyzing 11,300 B.t.u. and having an ash content of 12 per cent. When hydro-electric power replaced steam-driven equipment, the coal requirements were reduced; and, on account of improvements in metallurgy and/ or in furnace design, the quantity was lessened. Later, oil and distillate were introduced and used in some of the operations. All of these things tended toward the lessening of the amount of coal used, and had it not been for the increase in the size of the plant, the tonnage used would have been small when the change was made to gas.

Jan 1, 1932

By C. A. Meissner

The; following is a further discussion of the paper of James Qayley, " The Application of Dry-Air Blast to the Manufacture of Iron " (Trans., xxxv., 746), with special reference to his supplementary paper (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 797 to 819), and to the paper of J. E. Johnson, Jr., " Notes on the Physical Action of the Blast Furnace " (Bi-Monthly Bulletin, No. 5, September, 1905, pp. 1111 to 1146). Mr. Gayley's paper has been discussed also by E. Windsor Richards, R. w. Raymond, E. H. Saniter, W. J. Poster, H. M. Howe, V, Pendred, B. H. Thwaite, James Gayley and Alexander Pourcel (Trans., xxxv., pp. 1022 to 1042), Joseph W. Richards (Bi-Monthly Bulletin, No. 4, July, 1905, pp. '703 to 718); T. W. Robinson (Bi-Monthly Bulletin, No. 4, July, 1905, pp. 788 to 796); C. B. Dudley, R. W. Raymond, J. E. Johnson, Jr., W. F. Mattes, James Gayley, David Baker, John Birkin-bine and F. E. Bachman (Bi-Monthly Bulletin, No. 5, Septem-

Jan 1, 1907

By H. L. Barr

THE following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geol-ogists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions.

Jan 1, 1940

By F. R. Zacher

Unmined blocks in the Sewickley seam, surrounded by worked out areas, have been found to transmit overburden oads through the interval strata to the Pittsburgh seam workings 90 ft below. Operating experiences under these conditions are described in this paper. IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1953

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct Cr region were carefully resolved. Phase relationships in the 50 to 100 atomic pct region were outlined. A single intermediate phase, ZrCr,, was established in the system. A eutectic and a eutectoid were found in the zirconium-rich region of the system, while a eutectic was located in the chromium-rich region. Limited solubility of chromium in both a and a zirconium was observed. THIS is another in a series of papers on zirconium-base binary phase diagrams based on a program sponsored by the Atomic Energy Commission. The Zr-Sn,' Zr-Si,' and Zr-Mo and Zr-W" systems have already been published. Previous work on the Zr-Cr system includes a partial diagram by Hayes, Roberson, and Davies' and a complete diagram by McQuillan." The phase relationships reported by these authors were determined with magnesium-reduced zirconium, whereas those reported herein are based on iodide metal. Some X-ray work on the intermediate phase in this system was also reported by Hayes et al., as well as by Wallbaum.' Comparisons with these data are made in the appropriate sections. Thermal analysis, metallographic and incipient melting techniques were employed to accurately resolve phase relationships in the 0 to 50 atomic pct Cr region, while the remainder of the diagram is outlined on a basis of cast structures and thermal analysis. A description and analyses of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar (Westinghouse "Grade 3") was used. This material was produced by the decomposition of a volatile iodide onto a hot zirconium filament. The as-received crystal bar was coated with corrosion product from a standard autoclave test by which its grade designation is determined. A sand-blasting and subsequent HF-HNO, pickling treatment was employed to remove this contamination. The bars were cold-rolled to approximately 1/32-in. sheet, pickled again, sheared to 1/4-in. squares, washed with acetone, and stored for use. Ingot chromium metal from National Research Corp. and electrolytic chromium flakes from Johnson, Matthey and Co., Ltd., were available as alloy additions. The ingot chromium was received in granular form. The large granules were sized by crushing, treated for iron removal, rinsed with acetone, and stored. The flakes were broken to approximately 1/8 in. with mortar and pestle, cleaned with acetone, and stored for charging. Experimental Procedure A nonconsumable electrode arc furnace identical to that described by Hansen, Kessler, and McPher-son,' was used in this work. A 400 amp dc welding generator was the source of power. To insure homogeneity, ingots were melted in a water-cooled spun copper crucible, a total of four times without opening the furnace. No difficulties were encountered in the preparation of these binary alloys. Analyzed chromium contents were found to agree very well with the intended content. Melts of pure zirconium were interspersed in the course of preparing the alloys and their hardness was measured to keep a constant check on the melting technique. Vycor and quartz bulbs were used to contain the samples for isothermal annealing treatments. Vycor bulbs were employed for temperatures up to 110O°C, while quartz was used above this temperature. For treatments up to 950°C the bulbs were evacuated before sealing, but for higher temperatures a partial pressure of argon was admitted to the

Jan 1, 1954

By F. R. Zacher

Unmined blocks in the Sewickley seam, surrounded by worked out areas, have been found to transmit overburden oads through the interval strata to the Pittsburgh seam workings 90 ft below. Operating experiences under these conditions are described in this paper. IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1953

By John C. Branner

Inquiries are frequently made concerning the chalk- and clay-beds of Arkansas, usually with a view to the manufacture of Portland cement. The chalk-deposits were first described by Professor R. T. Hill in the annual report of the Geological Survey of Arkansas for 1888, vol. ii., pp. 153-162. Since the publication of that report I have visited localities then unknown, and have accumulated considerable additional information concerning these deposits, dl of which is brought together in the present paper. My report upon the clays of the State has never been published; only a few of the more conveniently available deposits are mentioned in the present paper. The Chalk-Deposits. Stratigraphic Position of the Chalk.—The chalk-deposits of Arkansas belong to rocks of Cretaceous age. The Cretaceous rocks are confined to a single definite area in Southwest Arkansas. Beginning on the Ouachita river, a little northeast of Arkadelphia, its southern or upper margin follows a line about five miles southeast of, and approximately parallel to, the St. Louis, Iron Mountain and Southern Railway from Arkadelphia

Jan 1, 1898

By C. B. E. Douglas

In an interesting article on evaluation of the water problem at Eureka, Nev., W. T. Stuart describes how a difficult water problem, or one phase of it, may be evaluated by means of a small scale test. Test data are plotted by a method rendering, under certain conditions, a straight-line graph that can be projected to show how much the water table will be lowered by pumping at any specified rate for a given time. A formula is then used to determine the size of opening, or extent of workings, necessary to provide sufficient inflow to enable pumping to be maintained at that rate. At first glance this might seem the answer to a miner's prayer, but a word of caution is in order. It may not be the whole answer. Moreover, results obtained by the method described are reliable only for conditions approximating those assumed. Even where conditions do not meet this requirement, however, it may be possible to draw helpful inferences from the results, perhaps enough to facilitate another approach to evaluation of a problem.

Nov 1, 1955

Polluted air and water, despoiled land and excessive noise are the unwelcome results of the population growth and a rising standard of living. The consumption of goods and services, including metal products and minerals, by all people is increasing so rapidly that civilization is in danger of destroying the environment in which it lives. This is true because every human activity affects the environment, whether it is air, water or land. While E. F. Osborn, director, U.S. Bureau of Mines, says . . . "some members of the mineral industry are reluctant to recognize environmental demands" . . . William T. Pecora Under Secretary of the U.S. Department of the Interior.. . says that, "to maintain levels of resource development and environmental quality needed to satisfy our affluence, we must trade off values rather than turn off troublesome operations." What it seems to boil down to is how much control of its operations is the mineral industry willing to accept-internal policing or strict government control? The answer lies in how well the mineral industry maintains a balance between mineral development and environmental quality.

Jan 1, 1971

By R. E. Hook, H. J. Garrett, A. M. Adair

X-ray diffraction and metallographic techniques were employed to examine the impurity phases occurring in as-swaged and recrystallized chromium produced fvom high-purity iodide chromium crystals. Chromium oxides are found to form in a consistent manner associated with the temperature of recrystallization. Microscopically observable second phase particles of Cr203 are observed to form intergranulurly beginning at 1300T. Beginning at 1500°C. Cr30, is formed intergvanulurly, atzd at 1600°C and above Cr30, is also formed in association with migrating grain boundaries. Geometrical traces formed by particles of this high temperature oxide uithin the grains rez)eal the histmy of grain boundary motion. X-ray evidence is presented which suggests the existence of a high temperature form of Cr203. Other impurity phases in addition to the oxides of chromium are also present. THE partitioning Of impurity elements between grain boundary aid lattice sires, either as solutes in solution or as second phases, may exercise an important influence on the mechanical behavior of metals and alloy systems. This partitioning of impurities could have a direct bearing on the iecrys-

Jan 1, 1963

By AIME AIME

THE quarters provided for the session on Milling Methods, Monday afternoon, Feb. 17, were filled to capacity. Galen H. Clevenger presided and notables, such as A. W. Fahrenwald, A. O. Gates, F. A. Thomson, W. L. Zeigler and others who had not graced a milling meeting in New York in recent years, or per- haps even never before, were actually present and spoke "in person." The first paper, by A. W. Fahrellwald (T. P. 275), entitled "Classifier Efficiency ; An experimental Study," was summarized by the author, who clearly showed the inconsistency of determining the efficiency of a classifier by means of sizing tests, especially where the material classified consists of a mixture of minerals of different specific gravities. In place of sieve analysis the procedure recommended involves the use of a glass settling-tube which is considered to give ideal classification and thus serve as a standard against which mill classification will be compared and relative efficiency calculated. This procedure sounds logical. Perhaps the greatest difficulty may lie in securing an ideal classifier acceptable to every one.

Jan 1, 1930

By JAMES H. McGRAW

P UBLZCLTY and engineers do not mix. In the very words of my subject, there is an apparent contradiction. In the past, publicity has been abhorrent to the engineer. It seems to be true that the engineer, because of his training or his background, has developed a state of mind which omits publicity. At any rate he has done a poor publicity job for himself. The average engineer is self-conscious; he ought to be class-conscious. If T should ask the men in this hall to get up one by one and tell who they are and what they have done, there would be an instinctive reaction in the mind of each man-a feeling that this was out of place. If I should ask each man to get up and tell something about his neighbor, I should find that each neighbor, once he got acquainted with the man next to him and understood what he was doing, would be as human and as generous-hearted in telling about his brother engineer as is any professional man.

Jan 1, 1920

By S. F. Turcotte, B. J. Grierson

At the Q. I. T. ilmenite smelter, nine electric furnaces produce titania slag and iron At high power levels, a furnace requires either a slag or an iron tap approximately once an hour, using rail cars as slag receptacles and ladles for iron. The correct scheduling of taps is an important operational tool due to peak power load and operational considerations. Over recent years, large increases in furnace capacity have imposed severe strains on the product handling facilities. This situation results in loss of production when several taps are bunched, because of an in- ability to handle many taps simultaneously. An on-line computer program has been developed to generate schedules for tapping a single furnace. By improved scheduling, this program can en- large the tonnage of each tap and minimize the number of taps, while reducing traffic congestion and unit cost s. Future plans call for extension of this technique to all nine furnaces with addition of a master scheduling program to optimize the overall traffic flow in the smelter aisle.

Jan 1, 1969

By K. R. Waugh, Barbara S. Brown, D. W. James

AN electronic data-processing system is described which permits rapid, accurate, low-cost processing of strain-dependent damping data utilizing equipment normally available within the service facilities of most large laboratories. On analyzing the record of a stress-dependent damping test, the operator usually measures the double amplitudes at several points on the decay curve. The logarithmic decrement is then calculated for decay between consecutive amplitudes. These values of 6 are plotted against the corresponding maximum surface shear stress, T, which is proportional to the average of the two amplitudes between which is calculated: where d is the specimen diameter. The period of the vibration is not necessarily constant during decay; thus, each cycle must be counted. A decay curve may extend to, perhaps, 1000 cycles, and at least two curves are always obtained for each specimen or set of conditions. It can, therefore, be seen that manual analysis of decay curves is both tedious and costly in terms of man-hours. Furthermore, the resolution of the record is often such that accurate measurement of amplitude is extremely dif-

Jan 1, 1969

PAUL D. MERICA,* Washington, D. C. (written discussion t).-This paper is a discussion of some of the results of a recent investigation1 of Prof. Zay Jeffries, and of his interpretation and generalizations from these results. This work I have followed with great interest and with appreciation of its value in clarifying our views on the nature of deformation in metals and its relation to structure. It is only by such close study of the relation of structure to mechanical properties that we shall ever be able to describe the latter in terms of their ultimate elements, and thus explain what are still mysteries in the mechanical behavior of metals; experiment and thought along these lines are in my opinion of the utmost value. If I, therefore, here record some of the difficulties I have experienced in understanding some of the generalizations of Prof. Jeffries, it is only in order that perhaps from the discussion may emerge a clearer and more consistent statement of hypothesis or theory in explanation of the facts discovered by him.

Jan 11, 1918

By N. C. Nissen, J. A. Thomas, A. Illis, K. N. Subramanian

Successful miniplant and laboratory testwork has indicated that high purity selenium can be produced from copper refinery slimes. The recovery technique fits into existing unit operations, and the selenium recovery in the new process was close to 99%. This recovery virtually eliminated any selenium being processed through the smelting stage. In addition, miniplant tests conducted at Inco Metals Co.'s J. Roy Gordon Research Laboratory in Mississauga, Ontario, have demonstrated the reliability of the process with respect to extractions, product quality, filtration characteristics, and effluent disposal. Inco's copper refinery at Copper Cliff, Ontario, produces about 500 t/d of copper with the anode slimes fall typically averaging 0.5% of the throughput. Investigations relating to the treatment of slimes within Inco's R&D have been conducted on several occasions since 1959, when the available alternatives such as acid or alkaline pressure leaching, aqueous or high temperature chlorination, roasting, smelting, etc., were considered. Interest in slimes processing was revived recently to meet increasingly stringent environmental standards and to replace equipment of a relatively old plant.

Jan 11, 1978

Minnesota School of Mines Experiment Station, University of Minnesota, Minneapolis, Minn For copies of Bulletins or a list of publications, address The Director Bulletins available are Bulletin 1, Iron mining in Minnesota, by C. E Van Barneveld (1912), $1, 2, Concentration tests on Mesabi ores, by W R Appleby and E Newton (1913), 3, Preliminary concentration tests on Cuyuna ores, by W. R Appleby and E Newton (1915), 4, Bibliography of Minnesota mining and geology, by W. Gregory (1915); 5, Manganiferous iron ores of the Cuyuna district, by E Newton (1918), 7, The future of the Lake Superior district as iron-ore producer, by E W. Davis (1920), 9, Magnetic concentra¬tion of iron ore, by E. W Davis (1921); 10, Ball mill crushing iii closed circuit with screens, by E W Davis (1925); 12, Minnesota manganiferous iron ore in relation to the iron and steel industry, by T L Joseph and S P Kinney (1927). A mining directory of Minnesota, by J J Craig, is published annually.

Jan 1, 1933