Search Documents

By B. L. Averba

THE determination of retained austenite by X-ray diffraction uses the following relationship:"" Pa = constant . RVaA (8) [1] where: P is the diffracted power from phase a; R, the calculated intensity factor; A, the absorption correction; 8, the diffraction angle; and Va, the irradiated volume of phase a For a flat sample making a glancing angle + with the incident beam the absorption correction is calculated as: * 1 sin (28 - 4) A .= 1 [2] µ sin, (28 — 4) + sin 4 where µ is the linear absorption coefficient. Beu3 has proposed that the computed absorption correction be combined with the constant and that the experimental observation of the absorption correction used in the original method be eliminated. This procedure is permissible only if: 1—There is no preferred orientation in the sample, and 2—The geometric requirements have been met precisely. If these conditions are not met the validity of the determination is questionable. Unfortunately the necessary conditions must be tested experimentally for each determination, and this is done most easily by observing whether the apparent absorption has the form of Eq. 2. In practice it may be convenient to plot P/R vs the parameter sin (2? — )[sin (28 — +) + sin +] to obtain straight lines for the ap- parent absorption correction. Deviations from straight lines indicate either that the sample has not been positioned correctly or that the relative intensities are incorrect. Geiger counter spectrometer methods also have been used successfully for retained austenite determinations. In the usual spectrometer arrangement the sample makes equal angles with the incident and diffracted beams (8 = ); thus the absorption correction is simply 1/2µ and independent of 8. The retained austenite is then easily calculated from integrated intensity measurements on austenite and martensite lines. If the austenite content is not too low and if excessive fluorescence is not encountered it is possible to use filtered radiation and a recording spectrometer. The integrated intensities are then proportional to the areas of the diffraction peaks. For lower austenite contents the following technique was used: A bent quartz monochromator and a Geiger counter spectrometer are employed. The monochromatic radiation is focused on the front slit, and the counter slit is made broad enough to include the entire line. A series of readings are taken in the vicinity of the diffraction peak. The highest reading includes the diffraction line plus background. The background is obtained from the average of several readings on each side of the peak. The integrated intensity is obtained by subtraction. CrK, and FeKa have been used for such determinations. This technique has been found to be as sensitive and as accurate as the photographic methods. In the spectrometer methods the ratio austenite/ martensite may be obtained from readings on austenite and martensite lines and the application of Eq. 1. It is also possible to use external standards and to obtain the austenite contents from measurements on the austenite lines alone. The small correction for carbides then becomes unnecessary. The best standards are probably samples with known

Jan 1, 1954

Professor Jenney has performed a notable service in presenting this summary of the steadily increasing body of observation on the presence of carbon in rocks of all kinds and its probable influence upon ore-deposition, and in formulating a mode of comparing directly the relative resistance of minerals to oxidation, as well as their reducing-power, and the protective action which minerals having higher reducing-powers exert in preventing the oxidation of associated minerals which possess relatively lower affinities for oxygen. I have had an opportunity of observing a vein which falls within the scope of his interesting discussion. The vein at Ku Shau Tzu, Mongolia, lies directly across a contact of limestone and overlying bituminous shales. Probably it occupies a compression-fissure. The shale has been reduced to such a condition of' non-coherence that much of it can be crushed in the hand, producing a handful of angular fragments resembling beech-nuts in shape and size. In the limestone the metals are principally in argentiferous galena with some pyrite and blende; but the latter two are very subordinate in quantity to the galena. In short, it is an every-day lead-vein in limestone, with siliceous limestone gangue. It is one of those veins in which the ore is not continuous, but consists of a band in the country-rock in which seams of lead sulphide begin at one wall and cross in a bent form, increasing in thickness, to the other wall, where they thin out and end. This may indicate torsional stress, but the shape of the lenses points to some other action. They often ran nearly parallel to the hanging-wall for a considerable distance and crossed the vein on a moderate angle, but turned sharply along the vein on approaching the foot-wall. The intermediate rock contains nodules, bunches and specks of ore, and the lenses vary exceedingly in size, shape and position in the vein.

Jan 1, 1903

By Henry S. Drinker

(Canal Zone Meeting, November, 1910.) FEW men reach middle life without having had the experience of failure in one or more undertakings; and most of us can look back with gratitude to help or advice given us by friends at critical periods of our lives. If, as men, we ask and take the benefit of such aid, why should we expect our sons to be stronger? A parent can make no greater mistake than to send a boy, however steady and intelligent he may be, off' to school or college, and expect the boy always to cope successfully with all the new conditions and new difficulties that may confront him. This is undoubtedly more the case with a freshman, in his first year at college, than in later years, or than it is with a boy at day- or boarding-school, where the boy receives a greater degree of care and oversight than can be given to the young man entering college; of all periods in life, the youth in his freshman year-fresh from the overshadowing care of home and school-may need judicious advice and timely aid. The change from the restraint of home and school to the freedom of college life is sudden and marked, and it is in this the first year of the boy or young man of 17, 18, or 19 years of age, that some tactful, judicious aid should be near him in his work and course. Some boys go to college so well prepared that they become careless and finally fall behind in their work from over-confidence. Others meet trouble from ambitiously trying to do more than their previous preparation, or physical or mental strength, can sustain. Others fall behind from illness-from injuries-from natural inability to grasp at first, without more aid than comes to them in the regular course of instruction, the higher mathematics-or mayhap the modern languages, or other subjects presented by the advanced curriculum of the present day. When a boy or youth begins to

Jan 1, 1911

By Harrison Souder

UNDER the stimulus of steadily in- creasing 'demands of the steel industry at home, and with the supply of available ores from abroad appreciably diminished owing to vigorous rearmament campaigns in Europe, production of Eastern magnetite ores reached an all- time peak in 1937. Although the figures given in the accompanying table are partly estimated (actual figures were available for eleven months only), it appears that 1937 production was nearly 47 per cent higher than that of 1936.

Jan 1, 1938

By F. D. Delve

RECENT studies by the author on the reduction of titanium from TiO2-bearing slags have been accompanied by difficulties that are attributed to

Jan 1, 1959

By AIME AIME

A MODERN copper reduction works has both a genera1 chemical laboratory for control work and a research laboratory for the study of improvement of present processes and better working-up of by-products. The division of work in the general laboratory would naturally differ in different plants. The following statement to the writer from a chemist in one of the works will give a good idea of the type. of work in the general laboratory :

Jan 1, 1929

By Benjamin F. Tillson

THE past seven years, and 1937 in particular, have witnessed the return of New Jersey iron mining to a place of importance. Following the World War period, little mining was done for several reasons. The properties were operated by small merchant furnaces whose demand was not sufficiently large to warrant large-scale methods with their attendant low operating costs. Under those conditions, the ore produced could not compete with that from the Great Lakes. However, when on Nov. 1, 1.929, the Alan Wood Steel Co., of Conshohocken, Pa., leased the Scrub Oak and Washington properties at Mine Hill and Oxford respectively, they made radical changes in the mining and milling processes which greatly reduced the cost of production and pointed the way to a renewed interest in mining in New Jersey. The following factors have been advanced as influencing the reopening of New Jersey mines:

Jan 1, 1938

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselrnan Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo.

Jan 1, 1949

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. We are referring here, of course, to properties inherent in the just solidified ingot and are not considering variations in properties caused by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. In plain carbon steels these elements are ordinarily not more than five: carbon, manganese, silicon, phosphorus, and sulphur. In alloy steels the special alloying elements also are specified and. determined. It might be thought that variations in properties due to such variations in ordinary chemical composition are to be expected, well understood, and hence not in need of discussion in this chapter. It will be considered here, however, that this phase of the subject is not always wholly clear. Furthermore, it certainly seems profitable to seek the explanation of anomalous properties in the ordinary chemical composition of the steel before looking into less well understood variables of open-hearth practice. It is sometimes surprising to learn that some puzzling variation in properties is caused merely by a variation in the ordinary analysis of the steel. This surprise is apt to be due not to general lack of knowledge of the effects of the composition of steel upon its properties but rather to the fact that we do not happen to have been previously much concerned with the particular property under consideration. For example, if we are accustomed to using S.A.E. 1035 bars for applications which depend chiefly on the stiffness, strength, and toughness of the steel in the as-rolled condition, we might quite logically develop the conclusion that variations in carbon content from 0.30 to 0.40 per cent are not significant. Then if we later have occasion to make heat-treated bolts of the same grade of steel, we may be surprised to

Jan 1, 1944

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output mines. The largest one, Fortuna mine in the Cologne district, produced a total of 45 million tons of lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95.2 million bank m3 equal to 200 million tons of overburden had to be removed to accomplish this lignite output. The largest BWE ever built is working in the Fortuna mine [(Fig. 1)]. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 tons and its wheel diameter 21.6 m, as high as a seven-story building. Major reasons for the development of BWE technology in Germany were: ? Lignite deposits with moderately consolidated, alluvial-type overburden (gravel, sand, loam, marl, clay, etc.) ? Great overall depth of the deposits, ranging far beyond 100 m, requiring a wide opening of the mine, hence not permitting direct overcasting of overburden. ? Multiple-seam deposits of poor-quality coal divided by reject partings, which demand a perfectly selective digging tool for clean separation. In general, these conditions are almost identical to those prevailing in the lignite deposits of Texas and neighbouring states: The type of overburden suitable for BWE digging, the overall deposit depth ranges down to around 100 m, and finally, the multi-seam occurrence with partings between seams, the latter ranging from just 1 m to a few meters in thickness. Technique As the Texas-type lignite deposits come into focus more and more as a possible fuel source in power plants to replace natural gas and crude oil, the following will deal with the BWE technology for mining a typical Texas lignite deposit under the aspect of producing enough fuel for a 500-MW power plant located at the mine mouth.

Jan 1, 1980

By N. A. Ziegler

CONSIDERABLE work has been and is being done on the changes of physical properties that take place in alloys at elevated temperatures, and much information on this subject is published. Much less is known, as pointed out by Rickett and Wood,1 about reactions between the alloys and atmospheric gases and still less is known about changes within the alloy itself under the influence of heat and given atmosphere. Moreover, most of the work published has been done on the alloys of "heat-resist-ing" type, in which chromium is an essential ingredient, the behavior of all other alloys being quite unknown, except perhaps of decarburization produced at the surface by oxidizing atmospheres. It has been shown' that iron, with total amount of foreign ingredients not exceeding 0.01 per cent, if heated in an oxidizing atmosphere at above 900° C., may be saturated with oxygen to 0.1 per cent. It was suspected that something of a similar nature may take place in iron-silicon alloys (transformer material), the mechanism of such processes being either a direct diffusion of oxygen into the alloy, or oxygen combining with silicon to form Si02 or more complicated (silicate) inclusions. Another possi-bility to be considered was that during annealing in oxidizing atmos-pheres, when scale is being formed, silicon may oxidize preferentially at the surface, thus impoverishing the alloy in silicon. In collaboration with Dr. T. D. Yensen,3 the writer set out to investigate this problem about two years ago in order to settle these questions.

Jan 1, 1934

By C. L. Warwick, A. B. Parsons

The papers and discussion appearing in this volume were presented at a symposium jointly sponsored by the American Society for Testing Materials and the American Institute of Mining and Metallurgical Engineers and held at Philadelphia, Pa., November 29, 30, and December 1, 1944. Late in January, 1944, Lieut. Col. C. H. Greenall, Officer-in-Charge of the Laboratory Division, Frankford Arsenal, Ordnance Department, U.S.A., suggested to the American Society for Testing Materials that it might be a propitious time to arrange for a symposium on stress-corrosion cracking at the Annual Meeting of the Society in June, and agreed to make available a number of papers relating to work being carried out at that Arsenal. The Society's Committee B-5 on Copper and Copper Alloys, Cast and Wrought expressed keen interest in the symposium, and other Society committees were contacted and agreed to cooperate. Since the subject is one of primary interest also to the American Institute of Mining and Metallurgical Engineers, it was arranged that the two organizations would jointly sponsor the symposium. A Symposium Committee was formed under the joint leadership, for A.S.T.M., of Carter S. Cole, then Chief of the Metals Branch, Conservation Division, War Production Board and now Engineer on the Headquarters Staff of the Society; and, for A.I.M.E., of E. A. Anderson, Chief of Metals Section, Research Division, New Jersey Zinc Co. (of Pa.) and chairman of the Program Committee of the Institute of Metals Division. The Symposium Committee was constituted as follows:

Jan 1, 1945

Soil Testing for Engineers. By T. W. Lambe. Published by John Wiley & Sons. 165 P. $5.00.-Filling a need for a text for the teaching of soil testing in the laboratory, this book is also of value as a reference for practicing engineers and for personnel in soil laboratories. Following an introductory chapter on general laboratory procedures are chapters devoted to the individual laboratory soil tests which are commonly employed. Apparatus, supplies, recommended procedures, discussion of procedure, calculations results, and numerical examples are provided for each test. Brief derivations of formulas and explanations and discussions of calibration procedures and special techniques are given in the appendix. Mesabi Pioneer. Copyrighted 1951 by the Minnesota Historical Society.- Publication of this book has been made possible by a generous gift to Society from the E. J. Longyear Co. of Minneapolis. This book covers the evolution of the Mesabi Range from a wilderness into the nation's greatest iron producing area. In this book is found the first hand experiences of Edmund J. Longyear who saw the development of the range from its beginnings, and who himself took a notable part in it. In 1890 Edmund J. Longyear sank the first diamond drill hole on the Mesabi. During the next two decades he sank pits and holes- 7133 of them-throughout the length and breadth of the Mesabi Range, exploring for iron ore. He saw roads and railroads built. He watched the range communities--Hibbing, Chisholm, Biwabik, Mountain Iron and the others change from exploration camps to

Jan 11, 1951

Writing the Technical Report, third edition, by J. Raleigh Nelson. McGraw-Hill Book Co. $4.50, 356 pp., 1952.-The aim of the book is to inspire a greater interest in report writing. Basis for the increased interest is a development of a keener understanding of the writer's own mental processes and the practical procedures involved in writing a report. The book is concerned with basic principles and procedures, rather than incidentals. It emphasizes the importance of correct attitudes and suggests a method of approach and organization. In the first part of the book, design and composition are considered. Next, the text gives directions for setting up both the long and short term report. The third part of, the book gives a systematic procecure for critical examination of the report. The fourth section presents a 16 week course in report writing. The Rocks of the Sekondi Series of the Gold Coast, by A T. Crow. Gold Coast Geological Survey. 7s. 6d, 73 pp., 1952.-The book describes the results of careful and detailed mapping of the Sekondi Series. The Sekondi-Takoradi area is undergoing intensive development, including extensions to Takoradi Harbor and to the railways. Details are given on the nature, extent, and structure of the Series and many faults which cut into them. The book is aimed at those with a practical interest in the area. It is illustrated with geological maps and drawings of horizontal sections. In the back, the terrain of the series is illustrated in a group of plates.

Jan 1, 1952

By Herbert Hoover

THE Federation of Engineering Societies has been created for the sole purpose of public service. This initial meeting surely warrants some discussion of a few of the problems to which this organization, for expression of the --. engineering mind, can quite well give consideration. Some of the greatest of the problems before the country and, in fact, before the world, are those growing out of our industrial development. The enormous industrial expansion of the last fifty' years has lifted the standard of living and comfort beyond any dream of our forefathers. Our economic system under which it has been accomplished has given stimulation to invention, to enterprise, to individual improvement of the highest order, yet it presents a series of human and social difficulties for the solution of which we are groping. The congestion of population is producing subnormal conditions of life. The vast repetitive operations are dulling the human mind. The intermittency bf employment due to the bad coordination of industry, the great waves of unemployment in the ebb and flow of economic tides, produce infinite wastes and great suffering. Our business enterprises have become so large and complex that the old personal relationship between employer and worker has to a great extent disappeared. The aggregation of great wealth, with its power of economic domination, presents social, economic ills which we are constantly struggling to remedy.

Jan 1, 1920

By Charles H. Fulton

FOR some time it has been thought that there should be > closer relationship between the members' of the Institute engaged in education in the mining schools, the mining, metallurgical, ceramic, and geological departments of universities, and the members of the Institute actually engaged in the production of mineral products and the operation and direction of works. The American Society of Chemical Engineers and the American Ceramic Society have for some years past devoted especial attention to the educational matters of their respective fields. The Engineering Foundation, representing the great engineering societies of the country, is deeply interested in technical education and maintains a Committee on Educational Research.

Jan 1, 1932

By AIME AIME

A JOINT meeting of the Canadian Institute of Mining and Metallurgy and the American Institute of Mining and Metallurgical Engineers was held at Spokane, Wash., and Cranbrook and Kimberley, B. C., on Oct. 13 to 16, 1926, with a total attendance at one or another or all of the meetings of about 300 members, ladies and guests. At the opening meeting, on Oct. 13, in the Davenport Hotel, Spokane, about 175 were present. The morning was occupied with addresses of welcome by M. H. Sullivan for the Columbia Section, who called on Mayor Charles A. Fleming, President John F. Davies for the Chamber of Commerce, and E. R. Hannibal, president of the Associated Engineers, each of whom heartily welcomed the visitors. Philip N. Moore, former president, and special representative of President Samuel A. Taylor, replied for the A.I.M.E., and Lewis Stockett, president, and Charles A. Banks, chairman, British Columbia Division, Canadian Institute of Mining and Metallurgy, and Henry M. Parks for the visiting A.I.M.E. sections, made appropriate responses on behalf of those they represented. The members and ladies had luncheon with the Associated Engineers. Philip N. Moore addressed the assembly on "The Opportunity of the Engineer"; an excerpt from his address appears on another page. At the afternoon meeting, with Lewis Stockett in the chair, Frank M. Smith was asked to make a brief statement of the proceedings of the Silver Producers Association in Denver. Supplementing his talk by placing a well-prepared statement on "Silver and the Plan of the Royal Commission on Indian Currency and Finance" in the hands of those present, he narrated what had been undertaken by the Silver Producers Association and what they hoped to accomplish.

Jan 1, 1926

By WILLIAM E. NEWNAM

THE molding and loading of pig lead has, in the past, been accomplished mainly by the strong arm method and, as the pigs are usually loaded directly into the cars, it has been a hot and laborious task. Of late years it has been difficult to obtain men willing to perform such labor and the need has been felt for loading and molding machinery which would eliminate all manual handling of the hot pigs and which would be sufficiently compact to permit of installation in existing plants with little or no

Jan 1, 1924

By Arthur Zentner

THE PAST YEAR saw important developments in all the main branches of zinc metallurgy, which can only be douched on briefly here. Vertical Retort Smelting-The New Jersey Zinc Co. reports their operations to be about as last year when the number of vertical retorts at the Palmerton plant was increased from 16 to 28. The first unit of eight vertical retorts at Oker, Germany, to treat the Rammelsburg complex ore was completed early in the year. A second unit has been under construction and is probably ready to start operations about this time. Each unit is rated for 10,000 metric tons of zinc per year. A plant of 40,000 metric tons annual capacity is the goal. A reflux plant was also built to make high-grade zinc. The plant program is being -carried forward with government finan¬cial assistance, as was the case with the electrolytic zinc plant at Magdeburg. Government subsidies cover mining and 'smelting, and allow for depreciation and reasonable return on invested capital, according to U. S. Bureau of Mines reports.

Jan 1, 1938

By W. J., Kroll

MOST people believe that rare metals are always, scarce in nature, expensive to make, and therefore useless despite some miraculous properties which might make them a cure-all. There are' some metals, which are quite frequent in nature, such as zirconium, which are called rare only because our present methods for making them are elaborate, thus forcing the manufacturer to sell them at a high price. There are also truly rare metals, such as gallium, which do not occur frequently in ores, but are easily reducible from their oxides. In these cases the price of the concentration operation is the decisive factor. The distribution of the elements in the earth's crust is no indication as to the availability of a metal; the concentration operation is the critical factor. Concentration is frequently obtained in the course of metallurgical operations for the extraction of other metals, and the rare metal may be enriched in by-products, flue dusts, mother liquors or precipitates from electrolyte purification as are indium, thallium, selenium, and tellurium. A periodic table of the rare elements may serve as a basis for discussion of their properties and to establish a program. (Table 1.)

Jan 1, 1946