Search Documents

By J. R. Jargon, H. K. van Poollen

Non-Newtonian fluids may be injected into a reservoir during secondary recovery operations. The non-Newtonian fluid used in this work is a power-law type of fluid that is, the viscosity of the fluid decreases as the flow rate or rate of shear increases. This paper presents equations for steady-state linear and radial flow of such fluids, transient behavior results from a finite difference model of a radial system, and transient behavior results from a field test. The equations that describe the flow of a non-Newtonian fluid are non-linear and are solved numerically. Finite difference solutions are presented as curves of dimensionless pressure drop at the wellbore us dimensionless time for a constant injection rate. Solutions were obtained for 5-percent, 10-percent and 100-percent PV of a non-Newtonian fluid for injection rates of 1, 10, 100 and 1000 cc/sec and for a 5 percent PV of non-Newtonian fluid located at T = Tw' 3, 10, 20, 50 and 100 ft for a flow rate of 1 cc/sec. The buildup curves do not exhibit a stmight-line portion as is the case for Newtonian flow through porous media. Correlations also are shown for the productivity index vs rate for the computer model study and the field tests. INTRODUCTION During various secondary recovery operations non-Newtonian fluids are injected. Such fluids, in general, include thickened water and gelled fluids. The term "non-Newtonian" implies that the viscosity is not only dependent upon temperature and pressure, but also on the rate of shear that is applied to the fluid. For example, water, which is a Newtonian fluid, will have essentially the same viscosity no matter what rate of shear is applied. A pseudo-plastic fluid exhibits a decreasing viscosity when higher rates of shear are applied; a dilated fluid has an increasing viscosity with increasing rates of shear. The objective of studies performed and described in this report is to obtain relationships and mathematical and empirical descriptions of the flow of non-Newtonian fluids through porous media. Simple mathematical relationships, computer studies that include the unsteady-state behavior of such fluids, and field tests are used. PREVIOUS LABORATORY STUDIES Laboratory studies have been performed by several investigators. The fluids used in one investigationl were surfactant-stabilized dispersions of water in hydrocarbons. Its Fig. 6 is reproduced as our Fig. 1. This effective-viscosity vs frontal-velocity diagram shows that this fluid is of the power-law type over a fairly large range of frontal velocities. Gogartyl developed an equation for the effective viscosity as a function of shear rate that reduces to Eq. 2 for frontal velocities greater than about 2 ft/D. The fluid characteristics used in the present study are similar to those reported by Gogarty. Christopher and Middleman2 performed experiments with power-law fluids flowing through pipes packed with glass beads. They used a modified Blake-Koteny

Jan 1, 1970

By Loyd R. Kern

A procedure for determining the behavior of a reservoir under a gas or water injection program was reported by Buckley and Levertt in 1942.1 This method, which allowed the calculation of the phase saturation distribution behind the front of a displacing fluid, has been extended to apply to a more general situation. The reservoir may initially contain flowing quantities of the displacing fluid, or the fluid in the reservoir may be above saturation pressure SO that solution effects are present. Production may occur behind the front as in the case of a well which is produced after breakthrough of the displacing fluid. The calculating procedure is simplified in that the graphical integration necessary to determine breakthrough saturation is eliminated by performing a direct integration and the graphical differentiation necessary to determine saturation distribution is eliminated by representing the displacing phase fraction of the flowing stream by an empirical equation. This representation results in simple expressions for the producing gas or water/oil ratio and cumulative production. INTRODUCTION A method for the calculation of the saturation distribution behind the front (interface between the displaced and displacing phases in a gas injection or water flooding operation) was reported by Buckley and Leverett in 1942. The method leads to a curve for the saturation distribution which is double-valued; consequently, part of' the curve was interpreted to be physically meaningless. That part of the curve which has physical significance was determined by a graphical integra-tion (material balance). In this paper it is shown that the integration may be performed analytically with a resulting equation for the saturation of the displacing phase at the front. The case in which the displacing fluid is initially flowing and the case in which the reservoir is initially above the saturation pressure so that some injected gas goes into solution are included in the integration. The calculations are considerably simplified by representing the fraction of the flowing stream which is oil by an exponential function of saturation. The methods is extended to apply approximately to reservoirs in which wells located between the injection well and the front are produced. An illustrative example utilizing the methods presented is included. RESERVOIR BELOW SATURATION PRESSURE In the case of a water flooding operation or in the case of a gas injection operation in which no gas goes into solution in the displaced oil, the equation for saturation in a linear flow system as a function of time and position as given by Buckley and Leverett is where* q = total reservoir volume flow rate, rvb/day A = cross sectional area of system, sq ft / = porosity of formation x = distance from injection point, ft t = time, days Pj = saturation of the displacing phase /dx velocity of planes of constant saturation, ft/day *The nomenclature used here is not the same as that used by Buckley and Leverett A complete nomenclature is given in Appendix A.

Jan 1, 1952

By R. Taggart, D. H. Polonis, J. C. McMillan

Thin foil electron microscopy techniques have been used to study the micros tructure of a Ti- 7.5 wt pct vanadium alloy in the quenched and aged cond_itions. Selected area diffraction has identified a (1011) twinning mode accompanying the martens ite t9.an.sfo?rn~ation. Precipitation of the 0 phase during the aging of quenched alloys has been obsevced to occuv in the form of plates and needles with preferential growth along the (1120) direction in the a' matrix. In the present work, the micro structures of quenched and aged alloys of the 0 isomorphous Ti-V system have been investigated by means of thin-foil electron-microscopy techniques. Most of the previous studies of martensitic phases in titanium-base alloys have utilized optical microscopy and X-ray diffraction techniques. The application of transmission electron microscopy is more recent, and only a few such studies have been reported.1-5 This paper is concerned particularly with the crystallographic nature of substructures formed in the martensitic a' plates. The early stages of aging or tempering have also been examined to determine the modes of precipitation from the martensitic solid solutions. Such information is essential in studying strengthening mechanisms and in determining the feasibility of high-strength rnartensitic alloys based on titanium. Liu and Margolin6 reported several types of substructures within the martensitic plates of quenched Ti-Mn alloys. It was later suggested by Liu7 that the structure of martensitic plates might be very complex and not single crystals as normally assumed. The sub-markings could not be identified with the two possible habit-plane orientations {334}ß and {344}ß, and it was not positively determined whether they are associated with mechanical twinning. The recent studies by Armitage5 on titanium martensites in a variety of commercial alloys have indicated that twinning does not generally accompany the transformation. This observation is in accordance with the Mackenzie and Bowles model for the transformation in pure titanium8 which suggests that twinning is not to be expected. However, a number of other recent investigators have reported twinlike substructures in the martensitic plates of several titanium systems including commercia1 titanium,2,3 Ti-Cu,5,9 Ti-Ta,1 and the commercial alloy Ti-8A1-1Mo-1V. Blackburn* has reported that the structure of quenched Ti-8A1-1Mo-1V depends on the prior solution temperature. He identified two types of martensitic structures, one of which is described as a heavily faulted hcp or twinned fcc structure and the other an hcp structure with a high internal dislocation density. The latter type exhibited some twinning with a (1011) twin plane. EXPERIMENTAL PROCEDURES AND RESULTS The alloy used in the present work was a 7.5 wt pct V alloy that was prepared by conventional arc-melting techniques. This alloy composition was selected

Jan 1, 1968

By David Turnbull

In most reactions involving solids the transformation kinetics may be represented by the combination of two processes —those of nucleation and of growth. For example, Mehl and his coiq-orker in their studies on the transformation of austenite to pearlite in steels have been able to describe the kinetics in terms of the rates of nucleation and of growth. By micrographic examination of their specimens they determined the nucleation rate (rate of appearance of pearlite colonies) as a function of time, of percent transformation, and of temperature. They observed that after an incubation period in which no nuclei are observed, the number of nuclei appearing per unit time per unit of untransformed grain boundary area, increases at an increasng rate with time. When recrystallization rates have been interpreted in terms of rates of nucleation and growth and the rate of nucleation determined, an incubation period followed by an increasing rate of nucleation has also been reported. Among the studies in which this phenomenon has been observed are those of Kornfeld and coworkers3 on cold-drawn aluminum wire, of Anderson and Mehl4 n the recrystallization of aluminum sheet, and of Stanlcy and Meh15 on the recrystallization of silicon ferrite sheet. The existence of an incubation period during which no nuclei are observed does not appear to have been reconciled with the generally accepted Volmer-Becker theory of nucleation in condensed systems. This theory ostensibly requires the rate of appearance of nuclei to be independent of time. Volmer-Becker Theory In order to form a stable nuclcus of a new phase B in a mother phase A, the molecules or atoms of the mother phase must surmount a free energy barrier whose height is determined by the volume free energy change accompanying the transformation and the energy of the surface separating the two phases. The free energy difference between nuclei of various sizes and the molecules or atoms of the mother phase is plotted schematically in Fig I as a function of the radius of the nucleus r. This free energy difference is plotted for two values of the change of free energy per atom, (Jb — ja) accompanying the transformation when the volumes of the two phases are infinite. One of these values of (Jb—Ja) corresponds to a temperature above the temperature To at which the phascs A and B are in equilibrium, and the other to a temperature below To. In order for a nucleus of phase B to be stable at a temperature T² < TO, its radius must be equal to or greater than the critical value r* for which the free energy of formatioil of the nucleus is a maximum, the of phase B having radii equal to or less than r* will be called embryos hfehl and Jetter," in discussing the kinetics of nucleation in solid systems, suppose that embryos of critical size are formed

Jan 1, 1949

R. H. Sweetser.—Mr. Reinartz spoke of slag containing 18 per cent FeO. I think he expressed the iron as oxide. I should like to ask at what point, in iron contents, it is usual practice to quit sending that open-hearth slag to the blast furnace? L. F. Reinartz.—NO problem is involved in disposing of open-hearth slag to our blast furnaces because, on account of the grades of iron and steel made by our company, the iron oxide in the slag is sufficiently high to make it very acceptable to the blast-furnace operator. I have been told that if the total iron oxide in the slag is under 18 to 20 per cent, it is not economical to use such slag in a blast furnace. J. T. Mackenzie,* Birmingham, A1a.—Mr. Reinartz mentioned sulfate in the limestone. I wonder if he did not use the wrong word. We always have assumed that the sulfate sulfur is practically harmless. Most limestone carries some pyrite (sulfide sulfur) which we thought was what gave the sulfur pick-up. L. F. Reinartz.—I have had no experience, personally, in the use of limestone high in sulfates. I have been told, on several occasions, by other open-hearth men, that the sulfates will be reduced and increase the sulfur content of the metal. We have never found any pyrite in our limestone. A. Hayes,† Middletown, Ohio.—I should think that sulfates would be readily reducible to sulfites, and possibly to sulfides at various distances through the slag layer, from the top down to the interface between the bath and the slag, because reducing conditions are certainly sufficiently strong next to the bath in the slag to reduce sulfates to sulfides. A. L. Feild,‡ Baltimore, Md.—What is Mr. Reinartz&apos;s theory as to the effect of silica in the slag on the iron oxide content of the metal? L. F. Reinartz.—I have no particular theory as to the effect of silica in the slag on the iron oxide content of the metal. I know from practical experience that it does have an influence on reduction of iron oxide in the metal. We know that if the silicon content of the charge, and, therefore, the silica of the slag is increased, the iron oxide in the slag will be decreased. Based on Dr. Herty&apos;s work, we assume that the iron oxide is correspondingly decreased in the metal. C. H. Herty, JR.,§ Bethlehem, Pa.—In the theory of iron oxide control, we have tackled the matter from the physical standpoint, rather than the chemical standpoint or from the slag itself, and we worked on the basis that the change in iron oxide content in a slag—that is, whether the slag increases or decreases in iron oxide—is due to the simple fact that if you put more iron oxide into the slag from the gas than you put oxygen from the slag into the metal, the slag must increase in iron oxide;

Jan 1, 1935

By J. T. Norton, J. G. McMullin

An 1820°C isothermal cross section of the Ti-Ta-C ternary diagram was prepared from X-ray diffraction and metallographic data. No phases other than those appearing in the three binary diagrams were observed. At temperatures above the titanium transition temperature titanium and tantalum form a complete series of solid solutions containing up to 2 atomic pct C. The phases Tic and TaC also form a continuous series of solid solutions extending across the diagram. PREVIOUS work on this alloy system was very limited. Of the three binary constitution diagrams involved, only one, the Ta-C system was available in the literature. Preliminary data on the other two systems was received from the investigators during the course of the investigation and both have been published in recent months. It had been shown that Tic and TaC formed a continuous series of solid solutions, but the range of carbon content in this phase was not known. While Ta2C had been described, its solubility for or reactions with other carbides had not been reported. It was not known whether or not any ternary compounds occurred in the system. The present program was undertaken to determine experimentally the general form of the ternary diagram. It is hoped that the results will be of value in furthering the development of sintered carbide cutting materials and high temperature ceramets, many of which contain combinations of Tic and TaC. The Binary Systems Of the three binary diagrams involved only that of Ta-C was available at the time this project was started. The diagram of Ellinger¹ redrawn in Fig. 1, shows a hexagonal phase Ta2C having a very small composition range and a cubic TaC phase having a composition range of from 40 to 50 atomic pct C. The authors made a separate determination of the composition range of TaC using lattice constant values and found the range to extend from 40 to 49.7 atomic pct C in good agreement with Ellinger&apos;s diagram. Two determinations of the Ti-Ta system have appeared recently.2,3 These two diagrams are in good agreement and show that ß titanium and tantalum form a complete series of solid solutions. The Ti-C diagram by Cadoff and Nielsen4 shows a very limited solubility of carbon in both a and ß titanium. The single carbide formed persists over a wide range of carbon contents. Several values for the upper limit of carbon content of this phase have been reported."&apos; The highest value obtained in the M.I.T. Laboratory was 47.5 atomic pct C with a lattice constant of 4.328?.5 Fattinger7 describes a gas carburization method which he claims produces stoichiometric Tic although he does not present any data showing that he actually had 50 atomic pct combined carbon. Several complete analyses on

Jan 1, 1954

R. H. Sweetser.—Mr. Reinartz spoke of slag containing 18 per cent FeO. I think he expressed the iron as oxide. I should like to ask at what point, in iron contents, it is usual practice to quit sending that open-hearth slag to the blast furnace? L. F. Reinartz.—NO problem is involved in disposing of open-hearth slag to our blast furnaces because, on account of the grades of iron and steel made by our company, the iron oxide in the slag is sufficiently high to make it very acceptable to the blast-furnace operator. I have been told that if the total iron oxide in the slag is under 18 to 20 per cent, it is not economical to use such slag in a blast furnace. J. T. Mackenzie,* Birmingham, A1a.—Mr. Reinartz mentioned sulfate in the limestone. I wonder if he did not use the wrong word. We always have assumed that the sulfate sulfur is practically harmless. Most limestone carries some pyrite (sulfide sulfur) which we thought was what gave the sulfur pick-up. L. F. Reinartz.—I have had no experience, personally, in the use of limestone high in sulfates. I have been told, on several occasions, by other open-hearth men, that the sulfates will be reduced and increase the sulfur content of the metal. We have never found any pyrite in our limestone. A. Hayes,† Middletown, Ohio.—I should think that sulfates would be readily reducible to sulfites, and possibly to sulfides at various distances through the slag layer, from the top down to the interface between the bath and the slag, because reducing conditions are certainly sufficiently strong next to the bath in the slag to reduce sulfates to sulfides. A. L. Feild,‡ Baltimore, Md.—What is Mr. Reinartz&apos;s theory as to the effect of silica in the slag on the iron oxide content of the metal? L. F. Reinartz.—I have no particular theory as to the effect of silica in the slag on the iron oxide content of the metal. I know from practical experience that it does have an influence on reduction of iron oxide in the metal. We know that if the silicon content of the charge, and, therefore, the silica of the slag is increased, the iron oxide in the slag will be decreased. Based on Dr. Herty&apos;s work, we assume that the iron oxide is correspondingly decreased in the metal. C. H. Herty, JR.,§ Bethlehem, Pa.—In the theory of iron oxide control, we have tackled the matter from the physical standpoint, rather than the chemical standpoint or from the slag itself, and we worked on the basis that the change in iron oxide content in a slag—that is, whether the slag increases or decreases in iron oxide—is due to the simple fact that if you put more iron oxide into the slag from the gas than you put oxygen from the slag into the metal, the slag must increase in iron oxide;

Jan 1, 1935

By Irwin Roman

IN studying the possibilities of a continuously recording magnetometer for use along the surface of the earth and in an airplane, the Federal Bureau of Mines was led to a study of the theoretical resolving power of magnetic observations, both in the variation of the total magnetic intensity and in each of the two components ordinarily measured. Along with this general study, an attempt was made to determine the relative worth of the total intensity anomaly and the vertical anomaly in geophysical prospecting. General considerations led to three conclusions: I. In the northern magnetic hemisphere of the earth, the total intensity anomaly is offset to the south of the vertical anomaly, for a positive anomaly (see Appendix, note I). 2. The resolving power of magnetic observations decreases rapidly with distance from the disturbing body. 3. The horizontal anomaly has little value in prediction of the disturbing body but might be useful in making a choice between bodies suggested by the vertical or total anomaly. Some of the considerations leading to these conclusions were: I. The normal intensity and the anomalous intensity are vectorially additive; hence for a positive anomaly in the northern magnetic hemisphere the total intensity will be a maximum at some point south of the disturbing body and north of the point at which the line to the disturbing body is parallel to the normal earth&apos;s field. The anomaly itself has a maximum value directly above the body. For a positive anomaly of constant magnitude, the total intensity will be a maximum when the anomaly vector is parallel to the normal vector. This is shown schematically in Fig. I (not to scale) for a magnetic distribution not restricted to a relatively thin sheet in the magnetic meridian. The normal field has a magnitude Io with vertical component Vo and horizontal component H,. Six station points along a traverse&apos; across the body from south to north are shown at M to S. At each of these stations the normal magnetic field vector terminates at F. At each of these stations the magnetic field vector due to the disturbing body B terminates at A. The line through the station point and the point A passes through B. The magnitude of the anomaly, indicated by the length of the vector terminating at A, is proportional to some power of the distance from the station point to the disturbing body. If the&apos; disturbing body B is a concentrated point of magnetic material, the anomaly is proportional to the inverse second power of the distance. For a uniform magnetic distribution over a line perpendicular to the observed traverse, the anomaly is proportional to the inverse first power of the distance. For surface distributions, the law of intensity is more complicated. At each field point, the total magnetic intensity T is the vector sum of the

Jan 1, 1946

By R. W. Raymond

to same extent, the assumptions tinderlying Dr. Ilu?ley&apos;s con alusions. These amrrmptions are: that &apos;the loss of metal per million tons of trafffc, depends, first upon the circrtnistances under which the rail is worn; secondly, upon the proportions of its various constituents, ancl that the anlorlnt of loss is afEect~d by eacb constitnent in a cer tain ratio, so that if the circunlstances were the same for all tlie mils, the wear per nliilion tons might he upproxi91ately expre~sed by an equation of the form I + Cc + Pp + SR + Mm = R, io wtlioh I is an unknown valne, dependi~.rg on the quantity of iron (and other ingre dients not determined) in the rail, and assumed to be constant for all the rails ; c, p, s, and m are the experimentally determined quan tities of carhon, phosphorus, sulphur, and manganese, as tabulater1 in YIates VT and VII of Dr. Dudley&apos;s paper; and R is the experirnen tdlly dcterlnincd wear per million tons; while C, P, S, and M are onknown wfficients. In other words, it is assunled that the differ ence in wear is proportional to a difference in c, p, s, or m, and that the effects of a change in the amonnt of either are independent of the amount of the rest-—within the experinlental limit5 of the problem. It is also assr~med that sulphar, copper, and other ingredients, not determined, are qually present in all the rails, or at least {lo not affect the wear, since I is taken as constant. Dr. Dudley tacitly assumes the coefficient6 C, P, S, and M to be positive; and assigns certain valries to them, by means of which he redom t.he equation to the form I + Pa: = R, x being equal to cc + Es +Mm i Pp, or tjje uanjbe,. of so-called phosphorus units in the rail. But we do not have R directly given under constant circumstances. The varying weights (per engine, car, or train) and the varying epds, we must neglect for lack of data, and assume that in these rwpects the rails examined have been treated srlbstantially alike. But there remain the varying conditions as to track, which mnst he elirninsted. Dr. Dudley gives six clrlsses, four of which contain 8 rails each, and two 16 rails each. Beginning with the 6~st (tangent grade), take the mean of the figures expressing wear for that clam; and continaing tliis process through the other five, we obtain six expressions in quantity of loss &apos;by wear, which we assome tc, represent, in their differences, the varying conditions of the trarli, with respect to grade and direction. We now take the mean of these moans (giving double weight to the gmiip containing 16 ohwrvafieras). This general rnean is the 10 of metal per million tons of trafio for a rail of avorage constitution under mean ciroumstances.

Jan 1, 1881

By S. C. Sircar, B. K. Dhindaw

KINETICS and mechanism of sulfation reactions have been studied extensively. Qualitative and quantitative data are reported for the kinetics and mechanism of sulfation reaction of copper oxide pellets;&apos;&apos;2 yet it remains a controversial Subject. The mechanism and kinetics of the sulfation of zinc oxide powder (B.D.H. analar quality) were studied by gravimetric technique. A spring of high-carbon steel wire with accuracy well within 0.2 mg was used for measuring weight change. The sample was taken in a Pyrex glass bucket, hanging freely inside a Pyrex glass tube reactor, with a gold wire attached to the spring, the reactor being surrounded by a movable furnace (double wound type) with a temperature control within *5"C. Flow of oxygen, 60 cu cm per min, and sulfur dioxide, 45 cu cm per min, were measured through calibrated flowmeters and the mixture dried over PZ05 before entering the reactor. The experimental results are presented in Figs. 1 and 2. The plot of weight change of zinc oxide, giving the amount of zinc sulfate formed, was found to be linear over the temperature range of 500" to 700° C and up to a conversion of approximately 60 pct, as beyond it they divert from linearity.&apos; The rate of sulfation was found to be affected by total flow rate of gases at a fixed ratio of SO2/O2, up to 60 cu cm per min, and was found to be linearly dependent on quantity of total powdered sample taken. The plot of rate of sulfation of zinc oxide, 70 mg, with varying amounts of vanadium pentoxide, at a constant ratio of gases as mentioned above, and at a constant temperature of 625"C, was also found to be linear as seen in Fig. 2. Extrapolation to zero V2O5 addition gives the same rate of sulfation, as in case of pure zinc oxide, 70 mg. Vz05 was prepared by heating ammonium vanadate at 600°C for 15 min in a muffle furnace. The available literature points out that the theory of sulfation that has received the maximum support postulates the following mechanism for sulfation of ZnS: 2ZnS + 30, = 2Zn0 + 2SOZ; the ZnO formed acts as a catalyst for the reaction, 2 S02 + O2 = 2S03. This SO3 reacts with ZnO to give zinc sulfate. It is suggested here that the above widely supported mechanism is operative in the sulfation reaction and that the rate-controlling step in the sulfation reaction of ZnO is the formation of SO3 from SO, and 0,. The authors are carrying on further work in this line, and the details will be published later. The authors wish to acknowledge the facilities provided and the help extended by Prof. P. R. Dhar, Head, Department of Metallurgical Engineering, and the permission granted to publish this note by the Director, I. I. T., Kharagpur.

Jan 1, 1969

WHILE papers on cleaning coal and mining coal were presented at the iron and steel and mining methods sessions, respectively, the first general session on coal was held on Wednesday afternoon. Howard Eavenson of Pittsburgh, Pa., as chairman of the session,* reported progress by the Committee on the Valuation of Coal for Blast-Furnace Coke. A paper on blasting coal effectively and safely in Southern Illinois, by J. E. Tiffany and S. S. Lubelsky, was abstracted and commented on by Dan Harrington, of the U. S. Bureau of Mines. W. J. German commented on some conditions mentioned in the paper as unsafe or bad practices, and added to these some further ex-amples; he made a strong plea for holes to be: drilled parallel to the bedding as the easiest way to determine the proper length or depth to agree, with the depth of kerf cut. Mr. Barron called attention to proper cutting and-drilling and rate of detonation of the explosive used, as effective aids in blasting coal. Another speaker mentioned an odd case where compressed black powder or "pellet powder," had decreased accidents at a non-gaseous mine where permissible explosives had been formerly used; the permissible cracked or shattered the roof, with a resulting high accident rate from falls of roof, and pellet black powder overcame this trouble. Eugene McAuliffe of the Union Pacific Coal Co. told of difficulties in changing from black powder to permissible in Wyoming mines. J. B. Dilworth read a paper on valuation of coal prop-erties, expressing a preference for the method of capi-talizing the earning power of a property. Eli T. Con-ner of Scranton, Pa., with much experience in valuation work, stated that the method was undoubtedly good, but many times failed because of inability to forecast accurately future earnings, and further contended that total valuation -and royalty rates could generally be fixed fairly when based on similar neighboring proper-ties&apos; rates when these had recently been established by a free bargaining. S. A. Taylor of Pittsburgh, Pa., stated that a leasehold value could be fairly established by figuring based on 10 to 20 per cent of the profit resulting from operation. The chairman read a written discussion from Henry Louis of England, called atten-tion to differences in valuation resulting from whether gross or net profit or earnings were used as a basis for capitalizing. John A. Garcia of Allen & Garcia gave a most inter-esting account of coal mining and general conditions in Russia as noted in his recent extensive visit there, which appears elsewhere in this issue. Although agree-ing with most thinking Americans that government operation is incompatible with progress, he showed that mining conditions were far from impossible in present-day Russia. Charles E. Stuart gave motion pictures of parts of the trip, with, his own comments supple-menting those of Mr. Garcia.

Jan 3, 1928

By Fred W. Stiefel

THIS paper covers the operation and maintenance of Diesel locomotives underground on a portion of the Delaware River Aqueduct.[t] This part of the tunnel is 15 miles long, with shafts 14 ft. in diameter spaced about 5 miles apart. These shafts (2, 2a and 3) are 825 ft., 1551 and 840 ft. deep, respectively. The grade of the tunnel is almost level, except for the 12,100 ft. north of shaft 2, which has a grade of 2.31 per cent. The tunnel is circular, 17 to 19 ft. in diameter. It lies at a depth of 400 ft. below sea level, with a maximum over-burden of 2400 feet. The tunnel driving was carried on in six headings, using 15 storage-battery locomotives, each of 13 gross tons and having a maximum speed of 8 miles per hour. The longest haul was 3 miles, which proved to be the maximum distance for which storage-battery locomotives could be employed economically for the amount of material to be moved. One locomotive was used for switching cars at each heading, one for switching cars at the bottom of each shaft and one on the main-line haul from the heading to the shaft. The maximum amount of material hoisted in one shaft from two headings when 104 ft. of tunnel was driven in 24 hr. was 1000 cu. yd., or about 2000 tons of rock in place. The total quantity excavated was 750,000 cu. yd. (1,500,000 tons of rock). The tunnel-lining operations using concrete presented a problem of hauling a maximum distance of 5 miles in the tunnel. The concrete-placing equipment had a capacity of about 2000 cu. yd., or 4000 tons in 24 hours. Experience had shown that storage-battery equipment could not handle this quantity of material within the time required at the distance of 5 miles. Trolley-locomotive haulage was considered dangerous and expensive, and would cause interference because transmission equipment would be required. Therefore the performance of Diesel locomotives of 160 hp., with a speed of 18 miles per hour, in comparison with that of other types of locomotives, was studied. CHOICE OF LOCOMOTIVES In deciding upon the type of locomotive to be used for the 5-mile haul, four alternatives were considered, as follows: I. To purchase additional storage-battery locomotives with the necessary batteries over the 6 locomotives and 12 batteries available. 2. To convert the existing battery locomotives to the trolley type. 3. To purchase new trolley locomotives. 4. To purchase Diesel locomotives. PROPOSITION No. I The 90-hp. storage-battery locomotives available (each weighing about 12 tons), when hauling a load of 64 tons, with a drawbar pull of about 1900 lb. on a level track, developed a speed of 8 miles per hour and could make five round trips in 8 hr. with a

Jan 1, 1942

By Earl Ingerson

BORE surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. METHOD AND APPARATUS In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel ,bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. st the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 5000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (1:16), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1947

C. M. Bishop (Aircraft Div., A. V. Roe Cnnada Ltd., Toronto)—Reference is made to the coherency hardening of ß due to ß&apos; and also to the hardening of ß due to a coherent precipitation of the a phase. What is meant by the term "ß&apos;?" Would not the coherency hardening of ß during cooling be due to precipitation of a sub-microscopic dispersion of a, as is the case during reheating a ß-quenched alloy? I feel that these two phenomena are essentially the same mechanism, i.e., precipitation of a from unstable or supersaturated ß. From the text, it would appear that Tables III and IV are intended to show the effect of the martensite transformation on the properties of Ti-Mn alloys. Referring to Table 111, the ß-quenched alloys would contain a greater proportion of retained ß than would the equilibrated alloy. Could not the increase in properties be attributed to this, along with possible coherency hardening of the ß? In the same way, the structures referred to in Table IV contain ß from which they could derive their hardness. It would appear to be difficult, if not impossible, to assess the role of the martensite transformation from the data contained in these tables. F. C. Holden, H. R. Ogden, and R. I. Jaffee (authors&apos; reply)—In reply to the first question raised by Mr. Bishop, the term "ß"&apos; designates an apparent retained-p structure which is harder than it is after the most rapid cooling from the ß field. It is thought to be the result of a coherent precipitation of a. The mechanism by which hardening takes place is undoubtedly the same as that involved in the early stages of aging of a re-tained-p structure, and we are in agreement with Mr. Bishop on this point. The term "ß&apos;" to designate the anomalously hard retained-ß structure was agreed upon at a symposium in 1953." The authors do not agree that the quantity of retained ß and/or ß&apos; in the ß-quenched specimens of Table III is necessarily greater than that of the 600°C equilibrated specimens. The ß-quenched specimen has a structure which appears to be completely a&apos; formed by the martensite reaction. It is recognized that there could be some retained ß (or ß&apos;) between the a plates if the M, temperature is below room temperature. This is unlikely for the 3.4 pct Mn alloy where the M, is known to be at about 640°C. Therefore, the increase in strength cannot be attributed to the presence of a greater quantity of coherency-hardened ß, but, rather, the increase in strength must be attributed to the transformation products formed, e.g., a&apos; (martensiti-cally formed a). Concerning the data in Table IV, we agree that it is difficult to estimate the role of the martensite reaction, since the 6.4 pct Mn alloy was retained ß in the quenched condition.

Jan 1, 1955

By A. A. Watts, R. I. Jaffee, F. C. Holden, H. R. Ogden

Hypoeutectoid Ti-Cu alloys are responsive to heat treatment, and considerable variation of mechanical properties may be produced by transformation of the ß phase. Control of cooling rate, isothermal transformation, or quench tempering determine the transformation structure and properties. The transformation products are similar to those of carbon steel. THE equilibrium diagram for the Ti-Cu system has been studied by various investigators, and the most recent diagram is that determined by Jou-kainen, Grant, and Floe.&apos; The titanium-rich portion of this diagram is reproduced in Fig. 1. The alloy compositions and annealing temperatures used in this work are shown. The Ti-Cu alloys containing up to 17 wt pct Cu are representative of an active eutectoid alloy system. Joukainen et a1.l have stated that ß phase cannot be retained on quenching and this has been confirmed in the present work. The similarity between the Ti-Cu system and the Fe-C system is evident and, as will be shown later, many of the transformation products appear to have similar microstructures. Heat treatments in this program were designed to produce the structures of primary interest for study and determination of mechanical properties. Experimental Procedures Preparation of Alloys: Five ½ lb ingots, ranging in composition from 0.8 to 6.83 pct Cu, were prepared by double arc melting in an atmosphere of high purity argon. Titanium melting stock was obtained from high purity iodide titanium, and copper additions were made from copper wire clippings. Segregation was reduced by inversion melting, in which the once-melted ingots were inverted in the crucible and remelted. The double-melted ingots were forged at 1600°F to ¾ in. diam rods, with both heating and forging operations being carried out in air. Surface scale was removed by grit blasting and grinding, after which the forgings were vacuum annealed at 900°C. The alloys then were swaged to ¾ in. diam rod at 750°C and test specimens were cut from this material. The vacuum annealing operation was to remove dissolved hydrogen, which is commonly present in the iodide titanium as-received. Although vacuum fusion analyses were not obtained for all these alloys, past experience indicates that the 6 hr treatment with a limiting pressure of 10- to 10-5 mm of Hg is sufficient to reduce the hydrogen level to 10 to 30 ppm. Vacuum fusion analysis of the 0.8 pct Cu alloy showed 19 ppm of hydrogen. In addition to the five hypoeutectoid alloys, three 15 g ingots were prepared with nominal copper additions of 9, 10, and 11 pct. Fabrication procedures were similar, except that these alloys were rolled to 0.040 in. sheet. Microstructure specimens only were obtained. Table I shows analyzed compositions and fabrication temperatures for these alloys. Heat Treatments: All heat treatments were made in potentiometer-controlled, resistance-wound tube

Jan 1, 1956

By Alfred V. de Forest

We are now assembled in this hall for the eighteenth lecture in honor of the memory of our greatest American metallurgist, Henry Marion Howe. Many of his most intimate contemporaries, led, as was fitting, by Professor Sauveur, have described his vital accomplishments in three fields: as a leader in technical industrial development; in theoretical research; and finally as a teacher and source of inspiration for nearly two generations of students. In 1914 Professor Howe had retired from active teaching, but maintained his laboratory at Columbia University under the care of Arthur G. Levy, with whom he published many of the papers that later were incorporated into his last book, " The Metallography of Steel and Cast Iron." My position at the time was that of personal assistant to Professor Campbell—no pay, no duties, but the great privilege of preparing specimens, taking pictures and attending to some of the current consulting work. Whenever possible, I visited Howe&apos;s laboratory to chat with Levy and gather ideas about the wonderful field of metallography—in which I was a rank amateur, rescued by the quiet enthusiasm of Donald Smith of Princeton from an instructorship in civil engineering. Levy let me act as a fly on the wall during the Professor&apos;s occasional visits. Busy as he was, Professor Howe took the time and trouble to encourage my interest, as he had done for hun- dreds of others. He told me how he went about gathering his own information speculating as to causes, considering experiments, and verifying his conclusions. I ventured to mention some tests I had run on the irregular stretching of wires of different metals. He read the small volume I had prepared of ill-assorted facts and fancies and remarked: "Nobody cares for your theories or the history of your tests. Describe what you found as briefly as possible and perhaps I can help you to publish." Curiously enough, among my discards were some autographically recorded load-versus-electrical-resistance measurements. Taken with inadequate knowledge and equipment, these curves did not reproduce consistently, but if the relationship between strain and resistance had then been explored, the latest type of strain gauge might have been in useful service for the past 25 years. Professor Howe was a gifted teacher, perhaps because he was primarily an ardent and assiduous student. His own eagerness to learn and his willingness to revise and extend his opinions constantly encouraged those of his environment to be diligent and painstaking in the pursuit of knowledge. In honoring his memory, I also wish to bring to mind the kindly, humorous and quiet Levy, and join his name again, as it was for too brief a space in the past, with that of many-sided Henry Marion Howe. Factors oF Impact Strength The subject chosen for the Howe Memorial Lecture by Dr. Gillett last year

Jan 1, 1941

By Alfred V. de Forest

We are now assembled in this hall for the eighteenth lecture in honor of the memory of our greatest American metallurgist, Henry Marion Howe. Many of his most intimate contemporaries, led, as was fitting, by Professor Sauveur, have described his vital accomplishments in three fields: as a leader in technical industrial development; in theoretical research; and finally as a teacher and source of inspiration for nearly two generations of students. In 1914 Professor Howe had retired from active teaching, but maintained his laboratory at Columbia University under the care of Arthur G. Levy, with whom he published many of the papers that later were incorporated into his last book, " The Metallography of Steel and Cast Iron." My position at the time was that of personal assistant to Professor Campbell—no pay, no duties, but the great privilege of preparing specimens, taking pictures and attending to some of the current consulting work. Whenever possible, I visited Howe&apos;s laboratory to chat with Levy and gather ideas about the wonderful field of metallography—in which I was a rank amateur, rescued by the quiet enthusiasm of Donald Smith of Princeton from an instructorship in civil engineering. Levy let me act as a fly on the wall during the Professor&apos;s occasional visits. Busy as he was, Professor Howe took the time and trouble to encourage my interest, as he had done for hun- dreds of others. He told me how he went about gathering his own information speculating as to causes, considering experiments, and verifying his conclusions. I ventured to mention some tests I had run on the irregular stretching of wires of different metals. He read the small volume I had prepared of ill-assorted facts and fancies and remarked: "Nobody cares for your theories or the history of your tests. Describe what you found as briefly as possible and perhaps I can help you to publish." Curiously enough, among my discards were some autographically recorded load-versus-electrical-resistance measurements. Taken with inadequate knowledge and equipment, these curves did not reproduce consistently, but if the relationship between strain and resistance had then been explored, the latest type of strain gauge might have been in useful service for the past 25 years. Professor Howe was a gifted teacher, perhaps because he was primarily an ardent and assiduous student. His own eagerness to learn and his willingness to revise and extend his opinions constantly encouraged those of his environment to be diligent and painstaking in the pursuit of knowledge. In honoring his memory, I also wish to bring to mind the kindly, humorous and quiet Levy, and join his name again, as it was for too brief a space in the past, with that of many-sided Henry Marion Howe. Factors oF Impact Strength The subject chosen for the Howe Memorial Lecture by Dr. Gillett last year

Jan 1, 1941

By E. M. Tory, P. T. Shannon

An analysis of batch and continuous thickening in terms of the movement of planes of constant concentration (i.e. continuity waves) is presented. Use of solids flux as a primary variable greatly facilitates the analysis and clarifies the relationship between batch and continuous thickening. An "ideal" slurry is defined as one whose settling rate is a function only of the local solids concentration. An analysis of continuous thickening of this ideal slurry in an ideal thickener explains many aspects of the steady — and unsteady — state behavior of real slurries, such as the main features of a thickener&apos;s "solids profile" (including the break attributed to rake action), the sudden appearance at abnormally high feed rates of a zone of constant concentration and the velocity with which it rises, and the effect of detention time at constant weight of sludge per unit area. Where deviations exist, they are explained in terms of the batch settling behavior of real slurries. The purpose of this paper is to interpret continuous thickening phenomena in terms of batch settling behavior. Both types of thickening may be considered as the process of propagating concentration changes, due to the downward movement of the solids, from the bottom of the settling vessel upward through the slurry.&apos; These concentration changes may be either finite or infinitesimal as in the case of the propagation of a continuous concentration gradient. The slurry itself may be moving downward as in the case of continuous thickening. The downward velocity of the slurry may be such that the concentration changes being propagated up from below remain stationary relative to the thickener walls. This is the case for steady-state thickening. It seems appropriate to analyze continuous thickening in terms of the movement of planes of constant concentration. This has already been done for batch settling."3 Although our main interest is in real slurries, there are certain aspects of both types of settling which can be deduced from a theoretical analysis of highly idealized systems. To this end, an "ideal slurry" is defined as one for which the dimensionless settling rate at any point is a function only of the local solids concentration.1,2 An "ideal thickener" is one in which there is no radial variation in either the solids concentration or in the downward component of slurry velocity. The underflow outlet is a point sink. It is to be expected that the behavior of non-ideal systems will deviate in some measure from theoretical results. However, the same characteristics which cause deviations in continuous thickening should be evident in batch settling, permitting a rational explanation of the former in terms of the latter. PREDICTED RESULTS FOR AN IDEAL SLURRY IN AN IDEAL CONTINUOUS THICKENER General Theory: In continuous thickening, the downward solids flux (mass/area-time) relative to the thickener, G, results from two different

Jan 1, 1967

By L. Burris, G. A. Bennett, P. A. Nelson

Staznless steels ave rrzuch less seuel-ely attacketl by zinc lapov than by molten zinc systems. To determine the applicubility of stainless steels fov equipment items which would be exposed only to zinc vapor, the corvosion resistance of several stainless steels to zinc vapor was investigated in 500-hr- exposuves at 900° C. Two austenilic stainless steels, Types 304 and 3-17, suffered severe intergranular attack. Loss of nickel from these steels and micro-probe crnalyses indicated the probable formation of low-melting zinc-rich phases. Good vesistance to attack by zinc vapor, as determined by metallo-9-rpaphic excr)rtination and physical testing, Loas exhibited by Type 405 stainless steel, a jevvitic steel. Type 440C stainless steel, a tnartensitic steel, although suffering considevable loss in weight, was not structurally weakened. At Argonne National Laboratory liquid zinc and zinc-rich alloys are being employed as solvent media in pyrometallurgical processes under development for recovering and purifying discharged reactor-fuel materials.&apos; Because of the high solubility of most metals in liquid zinc,&apos; there are few metals which can serve as container materials for liquid zinc at temperatures much above the melting point. The poor corrosion resistance of the common metals and alloys to molten zinc has been discussed by Eldred.3 DeKany, Lavendel, and Burris4 tested some of the less-common alloys of the nonrefractory metals and found that they also have poor resistance to attack by liquid zinc and Zn-Mg solutions. Of the metallic materials, only some of the refractory metals such as tantalum, tungsten, and molybdenum and their alloys have shown resistance to attack by liquid zinc.4-7 In the process-development work at Argonne National Laboratory, tantalum and tungsten vessels have been used to hold liquid-zinc alloys. These vessels are housed in stainless-steel equipment, principally to permit maintenance of an inert atmosphere and operation at various pressures. In this experimental work, it has often been observed that Type 304 stainless steel suffers little attack by zinc vapor at temperatures up to about 800 °C. In contrast, severe attack occurs in areas where zinc condenses as a liquid. The extent of attack by zinc vapor on several stainless steels was investigated because there are possible useful applications of stainless steel for equipment items which would be exposed only to attack by zinc vapor. These applications include, for example, housings around processing equipment as indicated above and vapor lines leading from zinc stillpots or retorts to condensers. EXPERIMENTAL EQUIPMENT AND PROCEDURE The experimental procedure consisted in exposing stainless-steel test coupons to static zinc vapor for 500 hr at a temperature of about 900°C. The apparatus, shown in Fig. 1, consisted of a 12-in.-long closed tantalum tube jacketed in Type 304 stainless steel to prevent oxidation of the tantalum. A Zn-10 wtpct Mg* alloy charge of 293 g in the bottom of the

Jan 1, 1965

By R. B. Hoy, Stanley J. LeFond, K. Reckling

Reported world production of natural diamonds approximates 40,000,000 carats a year (1980). The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, the Republic of South Africa third, and Botswana, fourth. Diamonds are also mined in South-West Africa (Namibia), Angola, Ghana, Sierra Leone, and other African countries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today it India, which was the first source of commercial production. In the US, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2,000 years ago, only about 260 tons have been mined. In order to obtain I g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential materials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamond in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (14/16 US mesh size). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite®, General Electric&apos;s Compax® and Stratapax® and Megadiamond&apos;s Megapax® have replaced natural diamond in turning tools, mining and oil drilling bits and dressing tool applications. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to modify light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem diamond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today.

Jan 1, 1983