Search Documents

By W. A. Backofen

THE texture of cold-drawn copper wire has been described most often as a composite of [Ill] and [loo] directions aligned parallel to the wire axis.' Hibbard2 suggested that sufficient reduction will result in a single [111] texture and reported that after a reduction in area of 96.4 pct, such a texture was nearly obtained. Other work3-4 has shown that recrystallization within the temperature range of 300" to 1000°C does not alter the texture established by cold-drawing. In general, however, the texture of cold-drawn end annealed copper wire is not as well defined as the deformation texture. In the work reported here it was found that the double-fiber, deformation texture persists even after a reduction in area of 97.3 pct, and after recrystallization the texture is practically all [l00]. The wire used in this work was prepared in the following way. A 3/4-in. diam length of annealed OFHC copper was cold-drawn to a diameter of 1/8 in., a reduction in area of 97.3 pct. Each step in the drawing operation brought about a reduction in area that varied from 6 to 10 pct. Short lengths of this wire were etched in a 50-pct solution of nitric acid to a diameter of approximately 0.01 in. The texture of the cold-drawn specimens was determined with the conventional X-ray transmission diffraction technique using filtered copper radiation. The X-ray beam was directed perpendicularly to the wire axis and the diffraction rings were recorded on a flat film. Fig. la is typical of the photo-grams obtained and reveals that the cold-drawing schedule described above introduces a distinct, double-fiber texture with both [Ill] and [l00] directions aligned parallel to the wire axis. Supplementary measurements with a Geiger-Mueller counter of the intensity of reflection from (111) planes showed that the [111] component was much more predominant than the [l00]. Additional specimens of the drawn and etched wire were annealed in a salt bath at temperatures from 300" to 450°C. The texture of the recrystal-lized wire was studied with the same technique applied to the cold-drawn wire. Fig. lb is an X-ray photogram of a specimen annealed for 1 ½ at 300°C and is typical of those obtained from re-crystallized specimens. The photogram shows that recrystallization of this material is accompanied by the almost complete elimination of the [111] component of the deformation texture. A pronounced strengthening of the [100] component was evident from intensity measurements with a Geiger-Mueller counter. In summary, the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [Ill] and [loo] directions aligned parallel to the wire axis. Recrystallization of such wire at temperatures from 300" to 450°C introduces a texture which consists almost entirely of a [loo] alignment. Acknowledgment Sidney Rolle of the Scomet Engineering Co. generously supplied the OFHC copper used in this work. References 'C. S. Barrett: Structure of Metals. p. 382 (1943) New York. McGraw-Hill Book Co. 2 W. R. Hibbard, Jr.: Trans. AIME (1949) -185, p. 598; Journal of Metals (Sept. 1949) TN 19E. 3 P. 422 of ref. 1. 'E. Schmid and G. Wasserman: Ztsch. Physik (1926) 40, p. 451.

Jan 1, 1952

By F. H. Ellinger

TI HE crystal structure of neodymium has been re-A ported by Quill1 and by Klemm and Bommer"s to be hexagonal-close-packed, Strukturbericht-type A3, with a, = 3.650.4, c, = 5.890.4, c/a = 1.614. Klemm and Bommer,% owever, pointed out that the observed intensities of the lines of the neodymium powder pattern agreed only in part with the intensities calculated for the type A3 structure, and that the neodymium powder pattern showed extra lines which could not be traced to impurities. They found that these extra lines could be accounted for by doubling the c-axis, but apparently they did not consider their evidence to be sufficiently conclusive to justify reporting the doubled c-axis. In the present work, the structure of neodymium was found to be double hexagonal-close-packed. The neodymium metal used in the present investigation was obtained through the courtesy of F. H. Spedding of the Ames Laboratory. Its major impurity was stated to be 0.03 pct Ca. The author's spectrographic analysis indicated high purity and carbon was determined to be less than 30 ppm. X-ray powder specimens were prepared from filings stress relieved in vacuum at 200°C for 50 hr. Powder photographs were taken in an 114.6 mm diam camera (Straumanis film mounting) at room temperature and in a 19 cm diam Unicam high temperature camera at elevated temperatures. Copper x-radia-tion was used for all the photographs. The powder pattern of neodymium was found to index to a hexagonal unit cell with dimensions, as determined from the high angle Ka doublets, of: a.= 3.655+0.001.4; c, = 11.796+0.004.4; and c/a = 3.227 at room temperature. The measured density of neodymium shows that this cell contains 4 atoms, the calculated density is accordingly D, = 7.02 g per cu cm. The diffraction data for the first 15 lines of the powder pattern are listed in Table I. In a double hexagonal-close-packed unit cell, the 4 atoms would be in the positions (0,0,0), (0,0,%), (1/3, 2/3, 1/4), and (2/3,1/3,%) of space group P 6,/mmc. On the basis of these positions, the relative intensities of the reflections were calculated using the expression: 1+cos2 20 I oc \Frp 1 ' sin2 0 cos 0 where F is the structure factor and p is the multi- plicity factor. Since absorption was not taken into consideration, comparison of observed and calculated intensities should be made only for neighboring reflections. Each atom has 12 neighbors, 6 in the basal plane at a distance of 3.655.4 and 3 above and 3 below at the closer distance of 3.626.4. These distances correspond to an average radius of the neodymium atom of 1.820.4. The description of this structure in terms of A, B, and C close-packed layers of atoms is ABAC ABAC. ...... The structure repeats every fourth layer and the stacking sequence of the second, third, and fourth layers corresponds to cubic-close-packing of atoms. A series of powder photographs taken at successively increasing temperatures up to 680a10"C revealed that the double hexagonal-close-packed structure is stable up to this temperature. Acknowledgments The authw wishes to thank W. H. Zachariasen and A. S. Coffinberry for their helpful comments on this work and also Marion Gibbs for measuring the diffraction films. This work was sponsored by the United States Atomic Energy Commission.

Jan 1, 1956

By H. W. R. Wardlaw

This paper shows how the cost of the drilling operation per 100-ft drilled can be related directly to bit weight, rotary speed and hydraulic horsepower variations. This enables optimum drilling conditions to be determined in a rapid and concise manner. The paper also shows how data for such calculations cun be obtained quickly and accurately by the "drill-off" method suggested by Lubinski. Examples are given to illustrate the principles and methods used. INTRODUCTION The problem of drilling oil wells at lowest cost and hazard needs little introduction, since it has been with us virtually from the earliest days of our industry. With better understanding of the effect of the various factors of bit weight, rotary speed and hydraulic jet action, however, the problem has recently taken on a more scientific aspect, and engineers or groups of engineers have been assigned to study many of the facets of this problem not immediately apparent to the general observer. Moreover, the availability of better equipment and materials has enabled certain practices to be adopted which were hitherto impractical or uneconomic. This has paved the way for further efforts to reduce footage costs, and so on. The improvements to be made in drilling technology and cost reduction are by no means exhausted, and we still frequently hear of new records being set and new materials and equipment becoming available. Some of the analytical methods used by the author to assist in promoting faster and more economic methods of drilling, particularly in Venezuela, form the basis for this descriptive study. STATEMENT OF THEORY AND DEFINITIONS In a highly competitive industry, it is no longer permissible to regard penetration rate as the sole criterion for drilling efficiency. Every new technique, however spectacular, must nowadays be viewed in the cold light of whether it will eventually lead to lower cost per foot drilled. In the exposition which follows, therefore, actual drilling rates will play only a secondary role, and attention will be focused on the more important aspect of cost per foot drilled. Changes in drilling factors such as weight and rotary speed will be studied in the light of how they directly affect the cost of operations. The advantage of this method is twofold—(1) cost increments are indicated directly; and (2) the relationships are, surprisingly enough, simpler than those relating to drilling rates. To achieve these advantages, it is necessary to introduce a new unit of measurement which, although unfamiliar, is readily understood. The unit in question will be referred to as the "actual drilling cost factor" and will be designated by the symbol h. The unit is defined as the number of rotating hours taken to penetrate 100 ft of formation. The unit can be obtained immediately from the actual drilling rate (r) in feet per hour; thus, This latter transformation is so easily effected that it may be convenient to use h as an international symbol for drilling cost, and to delay conversion to dollars, bolivars, pounds, etc, per foot until actually required (e.g., for fiscal reasons, etc.). In actual operations, h was found to vary in a relatively simple manner with increases in bit weight. The variation in h with rotary speed was found to be somewhat more complex. However, this also could be enormously simplified by introducing a further factor known as L or relative bit life. The factor L is also defined very simply by dividing 1,000 by the rotary speed (N) in revolutions per minute.

By R. B. Ladoo, C. A. Stokes, R. N. Secord, A. L. Hall

INDUSTRIAL mineral history shows that the entrance of new, nonmetallic minerals into commercial production can be expected to occur from time to time. Latest entrant into the field is wollastonite. Except for one short-lived period in Kern County, Calif., starting in 1933, wollastonite has never before been produced on a commercial scale. But the signs are up for its entrance as an economic factor in the mineral market. Small scale experimental production from a deposit near Willsboro, N. Y., started about 1943. A pilot plant was built in 1949-50 and irregular, small scale, production has continued. In early 1951 Godfrey L. Cabot, Inc. of Boston, world's largest producer of carbon black, took an operational lease on the property to study the deposits and make market surveys. This became Cabot's first venture in the mineral field, when they took over operations and began design of a new mill, expected in production in 1953. Properties The properties and major uses of wollastonite are comparable to New York fibrous talc. It has about the same specific gravity and index of refraction as talc, but is somewhat whiter and softer. The two most important fields of use, paint and ceramics, are the same as for talc. Ground wollastonite has a fiber length as much as 13 to 15 times the diameter. This particular property makes it applicable in the paint field and others. In addition, the length-diameter ratio may be controlled to rather narrow limits by choice of grinding method. Another important commercial property is brightness or whiteness. Wollastonite reads from 92 to 96 pct of MgO on the G.E. brightness meter for a 99 pct -325 mesh grind. Purity and uniformity of product are important. Chemically, the wollastonite now being mined analyzes SiO2 51.76, CaO 47.56, FeO 0.46, MnO 0.04, and H2O 0.09 pct. Theoretically pure wollastonite analyzes SiO2 51.75 and CaO 48.25 pct. This analysis indicates over 98 pct calcium silicate, with only small amounts of contaminating ingredients. That these ingredients are not detrimental to color or brightness is shown by the high brightness value of the fine ground material. [ ] By-product calcium silicate from electric furnace production of phosphoric acid has little physical re-semblance. to this wollastonite, being an off color white, and lacking in fibrous crystalline character. Minerology Wollastonite is a calcium metasilicate, CaSiO3, a white, medium hard, fibrous mineral. In this deposit wollastonite occurs as well crystallized aggregates of bladed crystals intergrown with garnet, and with a few percent of green diopside. The beneficiated product is about 75 pct wollastonite, 15 pct garnet, and 10 pct waste, largely middling. Wollastonite-garnet ore occurs in at least two beds. The main bed, varying in true thickness from 30 to 70 ft, dips into the hill at an average 30° and is enclosed in gneisses. Diamond drilling has proven the orebody to an average depth of 200 ft along 2000 ft of outcrop with adequate tonnage for many years of quarry operation. The wollastonite-garnet ratio varies locally, but average composition is uniform over long distances. A friable ore, it is easy to drill, shoot, and crush. Beneficiation Unlike talc this ore has to be beneficiated. Successful treatment depends upon the fact that it contains virtually nothing but wollastonite, garnet and a minor percentage of diopside. A very pure wollastonite product can be made by high intensity magnetic and/or gravity separation methods.

Jan 1, 1952

By H. J. Ramey

A general solution is presented for the transient temperature distribution caused by radial movement of a cylindrical heat source through a homogeneous medium of infinite extent. This problem represents a highly simplified model of the movement of a combustion front during the thermal recovery of oil. Numerical solutions are presented for a heat source moving at a constant velocity, and a velocity inversely proportional to the radial location of the heat source. Numerical solutions are presented for both finite and infinite vertical thickness of the heat source, i.e., with and without vertical heat losses. The numerical solutions are used to estimate the fuel concentration needed to maintain a combustion front during the thermal recovery of oil. The sensible heat carried to the combustion front by the injected gas stream is discussed in regard to the fuel concentration. Numerical solutions for a heat source (combustion front) of finite vertical thickness indicate the field conditions that may be necessary to sustain the temperature of a combustion front above the ignition temperature of the fuel over considerable distances from an injection well. The results also have implications in regard to the quantity of heat required during ignition. The results of this computation apply to a highly idealized model of a thermal recovery process. But the results may be used as a guide in engineering consideration of the thermal recovery process. INTRODUCTIO N The thermal recovery of crude oil has received considerable attention since the publication by Kuhn and Kochl of laboratory and field tests of this method of oil recovery. Other publications2,3,4,5,6, since that time have dealt with various features of the thermal recovery of oil and have illustrated the extremely complex nature of this process. Vogel and Krueger7 described an electric analog computer designed to solve a moving heat source problem which was analogous to movement of a combustion front during the thermal recovery of oil. The heat source was maintained at constant temperature and was a cylindrical source of infinite height (no vertical heat loss) moving radially at either constant velocity, or at a velocity inversely proportional to the radial location of the heat source. Jenkins and Ramey2 presented analytical solutions to a similar heat conduction problem and pointed out the possible importance of vertical heat losses. The following presents a general solution to the transient heat conduction problem introduced by Jenkins and Ramey4 as well as numerical solutions for a wide range of conditions possibly similar to those that might exist during field operation of the analogous thermal recovery process. DESCRIPTION OF PROBLEM The problem considered in this paper is determination of transient temperature distribution caused by a cylindrical heat source of infinite or finite vertical height, moving radially through an isotropic medium of infinite extent. It is further assumed that the heat flux generated at the surface of the moving heat source may be a function of time such that the fuel concentration required may be constant, or permitted to vary, and that heat is generated at the surface of the heat source only. In regard to the thermal recovery of oil the assumption that heat is generated at the surface of the front is equivalent to assuming that the thickness of the combustion zone is infinitely small, or that the reaction rate between fuel and oxidant gas is infinite. The last assumption does not appear stringent. See laboratory information published by Martin, et al3 Under these assumptions the temperature distribution throughout an infinite medium caused by a heat source moving radially with an arbitrary velocity may be described by The heat generation function or heat flux at the surface of the source, +(t), is Note that the fuel concentration may be defined as a function of time. Eq. 1 is derived in the Appendix.

By Lawrence A. Roe

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% SiO2, 31.89% MgO, and 4.75% H2O. However, as an industrial commodity, talc rarely approaches theoretical purity. Nevertheless, the impure talc products of commerce find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are tremolite, chlorite, dolomite, mica, and magnesite. Steatite was originally a mineralogical name applied to pure talc. In today's commerce steatite generally refers to the massive variety of talc suitable for electrical insulator manufacture. Block steatite ore can be machined into various shapes. Impure varieties of massive or block talc are still commonly referred to as soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soapstone and talc, this is a natural thing since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as "slip") have been grouped together and called soapstone or talc. Further, there is a mineralogical relationship of pyrophyllite to montmorillonite and talc to hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Indians on Santa Catalina Island, Calif. In the mid-1800s, soapstone from deposits along the western foothills of the Sierra Nevada mountains was used by white settlers for building and ornamental stone and in the linings and foundations of furnaces (Anon. 1956). Previous to 1916, the annual recorded production in California did not exceed 2000 tons. In the period 1912 to 1918, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state's annual output of talc was in the range of 9,000 to 20,000 tons. In the mid-1930s, the use of talc in wall tile grew rapidly. In California, the production of talc grew to 63,000 tpy in 1943. The post-war building boom helped California production to grow to 120,000 tons in 1951. In 1968, production was 165,000 tons, 1969 was 145,000 tons, 1970 was 185,000 tons, and 1972 was 155,000 tons. Talc mining in New York state dates to about 1878 when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville, New York. In 1893, this operation was sold to the International Pulp Co. which changed its name to the International Talc Co. in 1944. Total production from seven New York mines, in 1948, was 130,000 tons. A new talc operation, the Gouverneur Talc Co. owned by the R.T. Vanderbilt Co., began operations near Balmat, N.Y., in 1948. The initial capacity of the processing plant was 200 tpd (Gillingham, 1950). Subsequent expansions have increased capacity to over 600 tpd. The Vermont talc industry began just after the start of the 20th century. Talc was discovered in the area of the present Johnson, Vt., talc mine in 1902. The American Min¬erals Co. initiated plant operations at Johnson in 1904. The Magnesia Talc Co. opened a plant at Waterbury, Vt., in 1913 (Burmeister, 1963; Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine has a long history as a producer of talc crayons. The Eastern Magnesia Talc Co. was formed in 1924 by a merger of the Eastern Talc Co.

Jan 1, 1975

By R. E. Collins

The existence of fluid migration across fixed boundaries in oil and gas reservoirs has been known for many years. Several techniques have been developed in the past for estimating The rate of migration across fixed boundaries as an aid in planninng field development and in the valuation of oilfied properties. The principal de/errc7nt to the use of these techniques lies in the rather extensive reservoir and field data required for ca1cula1ion.s of fluid migration. For this reason, a new, simplified procedure has been developed which makes possible the calculation of fluid migration with a minimum of field and resrvoir data. This new technique is based on certain. solutions of the differential equations describing flour in the reservoir which assume, for the portion of the reservoir of interest, that the formation can be approximated by a homogeneous rock of uniforrn thickness, that only a Single mobile fluid phase exists, and {hut fluid production at the well is solely a result of expun.rioti of rile resersoir fluds. The results of the, present work are compiled in a set of curves. These curves can he used to calculate both rule and cummulative fluid migration when the abovc assumptions ore ju.r/ifiril. The only data required for such calcu1ations are the production hisrories of all wells in the field, the permeability and porosity of the reservoir., the, compressibility and viscosity of the fluid. and the shape of the reservoir, INTRODUCTION The migration of fluids across fixed boundaries in oil and gas reservoirs has long been recognized as an engineering and economic problem, but no methods for estimating the extent of migration during the development stage of a reservoir have been published. The investigation reported here has been directed toward providing a simple technique for estimating the extent of such migration and has therefore been restricted to the simple case of a homogeneous reservoir of uniform thickncss containing compressible liquids. It is assumed that only a single mobile fluid phase exists and that fluid production at the wells is solely by expansion of the reservoir fluids. Obviously, few, if any. reservoirs conform to these assumptions during their entire productive life. On the other hand, most reservoirs approximate fluid expansion reservoirs during their initial stages of primary production. Consequently, the present work should be applicable during the field development of most reservoirs, regardless of whether or not they ultimately are gas cap, dissolved-gas, or water-drive reservoirs. The mathematical analysis of this problem has been outlined in the Appendix, while the results of the investigation are presented in the following discussion. DISCUSSION OF CALCULATION PROCEDURE SLNGLE Well, Ini-iimite Reservoir The procedure for calculating fluid migrations is based on solutions of the partial differentia1 equations describing the flow of a homogeneous compressible liquid in a homogeneous reservoir of uniform thickness. This differential equation has the form of the well-known diffusion equation. The equation, as applicable to our problem, is where p is fluid density, is porosity, EL is viscosity, c is compressibility,* and k is permeability; .r, y and t are the space coordinates and time. Derivation of this equation is given in the Appendix. The analytical solution of this equation for a single well of negligible radius producing at a constant rate. q, from a reservoir of infinite areal extent for a time, 1. can he readily obtained. From this solution the rate of flow and also the cumulative flow across a straight line segment of length, 1, at a perpendicular distance. 6. from the well can be computed. One end of the line must be on the perpendicular joining the well to the

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for OFHC copper, and for a series of binary solid solutions of high purity copper with zinc, gallium, germanium, arsenic, and silicon, to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity. The apparatus used was of the torsional pendulum type developed by KeI1 modified so that the specimen and vibrating system could be maintained in a high vacuum. The activation energy for grain boundary relaxation in copper is 33,000 cal per mol. This is considerably less than the activation energy for self-diffusion, in disagreement with Ke's theory2 that the two activation energies should be the same. All the alloying elements increase the activation energy for grain boundary relaxation to approximately 44,000 cal per mol, increasing the grain boundary viscosity at a given temperature. The results are discussed in terms of theories of grain boundary slip put forward by MottQ and by Ke.+ Experiments have also been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. EXPERIMENTS described in this paper were designed to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity, using the internal friction method developed by Kel for measuring grain boundary viscosity. It was considered desirable to make the system under investigation as simple as possible by making experiments on a comprehensive series of binary alloys of copper with the elements immediately following it in the periodic table, i.e., zinc, gallium, germanium, and arsenic. These elements are within the range of favorable size factor for solution in copper, and the systems have been extensively investigated by Hume-Rothery and his co-workers." Later, in order to study the effect of the relative size of the solvent and solute atoms, experiments were made on a series of Cu-Si alloys, since the apparent atomic diameter of silicon when in solution in copper—the diameter necessary to assign to the solute atoms to account for the lattice constant of the solid solutiona—is almost the same as that of the solvent atoms. Preliminary experiments were made to measure the variation of internal friction with temperature for pure copper. Ke made some experiments on copper," but found that the curves obtained were not reproducible in consecutive experiments. The copper was maintained in an argon atmosphere during the experiments but, although he took precautions to exclude oxygen, Ke came to the conclusion that the precautions were not entirely satisfactory, and that the lack of reproducibility must be due to absorption of oxygen by the copper. Experiments have therefore been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. Previous Work Ke made extensive experiments on high purity aluminum and was able to show that the grain boundaries behave viscously at high temperatures. He found that the relative rate of movement of the grains could be expressed as Where v is the velocity of slip, A is the constant, u is the shear stress, H is the activation energy, R is the gas constant, and T is the absolute temperature. By assuming that the boundary layer was one atom thick, he obtained a value for the viscosity which, when extrapolated to the melting point, gave good agreement with the viscosity of the liquid metal at the melting point. Ke also made experiments on other high purity and commercial purity metals:, and on some alloys." " He came to the conclusion2 that the activation energy for grain boundary slip was the same as for self or volume diffusion and for steady state creep in single crystals. Rotherham, Smith, and Greenough" have shown recently that the activation energy for grain boundary slip is not the same as for self-diffusion in tin,

Jan 1, 1957

By F. D. Patchen

Changes in the properties of partland cement upon the addition of fine-ground silica are discussed. Data were collected from formulations cured for periods up to 60 days at temperatures varying from 180" to 350°F. Compressive strengths, permeabilities and thickening times are compared. It is demonstrated that addition of find-ground silica in proper proportion results in a hydrated cement with superior properties above 230°F; i.e., early compressive strengths are higher and increase with additional curing, permeabilities are significantly lnrver and thickening times are increased. X-ray analysis of hydrated cement samples have been used to determine more fully the complex chemistry of these systems. Dicalcium silicate alpha-hydrate was found in all neat cements cured above 260°F. A 10 weight per cent silica addition produced a maximum amount of this phase. Xonotlite and tobermorite have been identified as hydration products at 320°F in systems containing 35 or more weight per cent silica. Formation of these components appears to be primarily responsible for the gain in strength and reduction of permeability observed after the addition of silica. INTRODUCTION For several years it has been recognized that loss of compressive strength occurs when portland cement is cured at a temperature above 250°F. This phenomenon has been called "strength retrogression". More recently it has been recognized that increased permeability usually is associated with decreased compressive strength at these temperatures. At curing temperatures above 300°F, these factors reach serious proportions. A compressive strength loss of 50 per cent between curing times of 24 hours and 14 days has been reported,' and permeabilities as high as 10 md have been measured in neat cements cured at 320°F for seven days.' Earlier investigators,' although unsuccessful in eliminating strength retrogression, stated ". . . .it appears possible that by the proper selection of additives for cement, strength loss with age at high temperatures can be either eliminated or considerably lessened". One solution suggested was the use of a pozzolanic material, hydrated lime, and a retarder. Menze15 in 1934 discovered that portland cement containing finely divided silica possessed high compressive strengths when the curing temperature was 350°F. The use of such a composition is now an established practice in the manufacture of steam-cured cement blocks. It is reasonable to assume that the same beneficial effect can be used advantageously in high-temperature oilwell cementing operations. Ludwig first mentioned the use of sand for this purpose. Later, a portland cement containing moderate additions of silica flour and retarded with CMHEC, a cellulose derivative. was recommended for high-temperature application." These formulations have been successfully employed in the field."'" This paper presents the results of a research program to test the efficacy of finely ground silica in increasing the compressive strength and reducing the permeability of oilwell cement compositions containing portland cement. Included also are X-ray diffraction patterns of powdered samples which have been used to determine some of the important chemical reactions occurring in these systems. LABORATORY PROCEDURES AND MATERIALS All compressive-strength test specimens were prepared and cured from a slurry in accordance with API RP 10B, with two modifications. A final curing pressure of 5,000 psi was maintained for a one- or three-day period; but, for further curing, pressures were reduced to the vapor pressure of water at the curing temperature. Also, the water content was varied in samples containing silica to maintain the slurry viscosity within a range of 5 to 15 poise as measured on a consistometer. Test specimens at 180°T were cured in a water bath at atmospheric pressure. At higher temperatures the specimens were cured in a steam-jacketed high-pressure curing vessel at 5,000 psi for a one- or three-day period. cubes cured for longer periods were removed from the pressure-curing vessel after 24 hours, sealed in small bombs containing water and placed in an aging oven.

By S. K. Mitra

A refinement of the Seeger model for intersection process is investigated which is in better agreement with experimental observations than the original. It is shown that, in single crystals, the strain hardening in Stage II is mainly due to the short-mnge interactions when intersection is the rate-controlling process. It is also demonstrated that the creep curves, as predicted by this theory, are in good agreement with the experimental observations. MOTT: Cottrell? and Seeger have developed an approximate theory for plastic deformation of single crystals over the range of variables where the strain rate is controlled by the rate of intersection of dislocations. Although it is now generally agreed that the low temperature deformation of many pure metals is controlled by the intersection mechanism, various dictates of the over-simplified Seeger model are not in good agreement with all the experimental facts. It is the purpose of this paper to reveal that by appropriate extensions of the Seeger model, particularly those suggested by Basinski: a much more reliable theory results. The refined model to be presented here will be shown to account, in a satisfactory way, for the effect of stress, temperature, and strain on the creep rate under constant stress and for the effect of temperature and strain on the flow stress in constant strain-rate tests. EXPERIMENTAL METHOD To Check the theoretical deductions, both creep and tension tests were conducted on single crystals of high-purity Al (99.994 pct Al) so oriented that both the active slip plane and the Burger's vector of the operative dislocations on that plane made angles of about 45 deg to the tension axis. Single crystals of aluminum (5/8 in. by 1/10 in. by 8 in.) were grown in a graphite mold under an inert atmosphere using the Bridgman method. The chemical composition of the aluminum is given in Table I. A common seed was used for all crystals and their orientation is shown in Fig 3. The extensometry consisted of two differential transformers with matched outputs mounted so as to measure the extension in a 2 in. gage length. The amplified difference in output of the two transformers was recorded by a potentiometer. The amplification was calibrated before each run so that one chart division of the recording potentiometer indicated a 105 shear strain on the specimen. Stresses were measured to the nearest 1 x l04 dynes per sq cm. ACTIVATION VOLUME The concept of Basinski that the activation volume is not constant but is a function of the force that aids thermal fluctuation in effecting the cutting of dislocations will be adopted in this section. The force acting due to an applied shear stress on the dislocation being intersected is where L is the mean spacing between the forest dislocations, is the Burger's vector and T is the back stress. A detailed discussion about the origin of back stress will be taken up later in this report. As shown by Basinski, the activation energy, U, that must be supplied by a thermal fluctuation in order to effect intersection, is equal to where x is the distance through which the dislocation must be translated for complete intersection, and Fm is the maximum force encountered in intersection. When the applied stress is decreased abrupt ly F also decreases and the activation energy increases correspondingly as documented in Eqs. [ 1 ] and [2]. The Seeger equation for the strain rate when the deformation is controlled by rate of intersection of where the shear strain rate (per sec) N = the number of points per unit vol at which intersection can take place

Jan 1, 1962

By W. van der Knapp

A theoretical and experimental ana1ysis is given of the change in volume of a porous medium due to changes in external and internal pressures. The result enable one to deduce directly the effect of large increlents in stresses. It is shown that the three-dimensional representation of the volume of a nonlinear porous system is a cylindrical rules surface, the generating lines of Which have a slope according to the solid rock compressibility. Analytical expression for such a ,surface is very simple. It follows that the bulk and pore compressihilities depend only on the difference between pore fluid and external hydrostatic pressure, i.e., the effective rock frame pressure. From measurements on a number of sandstones as well as limestones it can be conduded that for practical values of this effective frame pressure the pore compressibility falls in the range between the compressibility of water and that of undersaturated crude oil. In general, pore compressibility is found to be higher the lower the porosity. For a particular limestone reservoir pore compressibility and porosity could he related by means of a simple empirical formula. Results from the described study find a direct applicxtion in material balance calculations and in prob1ems of liquid flow through porous media. Since the elastic constants of the rock bulk material enter into equatiorls for velocity of acoustic waves, the results are also of importance for calculating rates of wave propagation in these media. It is shown for sandstones with 1.5 to -10 prr cent porosity that laboratory measured porosities may differ from those lender reservoir conditions by about I per cent of their value. The difference for low porosity limestotnes can be of the order of 10 per cent. The subsidence caused by elastic deformation of reservoir rock is shown to he very small. General formulas relating pore and bulk volume to external and internal pressure can be derived, as has been shown by Biot1, Gassmann2 and Geertsma.2 Their theories describe the differential change in volume caused by a variation in pore fluid tension and external hydrostatic tension. It has been known for a long timei that the stress-strain relations of a packing of spheres are essentially noninear. Our experiments show that for almost all reservoir rocks which arc elastically deformable the relation between volume and loading is also a nonlinear one, resembling that of a packing of spheres very closely. The behavior of these media is often described by using the linear stress-strain relations for small incremental stresses and strains in the vicinity of a pre-stressed condition." The present study differs from these considerations in that it enables one to deduce the effect of large increments in the stresses directly. In analogy to the stress tensor for a homogeneous body the stress tensor for a porous body can be written in the conventional way: where the tensor components, o, and t, represent the total forces acting on the faces of a unit cube of porous material. This tensor can be split into two parts. a hydrostatic and a deviatoric part, as follows2,3,1 where the component of the hydrostatic stress system, a. equals The hydrostatic stress causes a change in volume whereas the deviatoric stress system gives rise to a change in shape only. One of the difficulties in describing changes of volume occurring in reservoir rocks is that the relations connecting these volume changes with external and internal stresses are essentially non-linear. A complete description requires the bulk volume, V,,, as well as the pore volume,V,,. to be known as a function of both the changes in pore fluid tension (v) and the hydrostatic tension on the outer boundary.

By Alton B. Cook, G. B. Spencer, F. P. Bobrowski

In estimating production gas/oil ratios and oil recoveries from reservoirs containing highly volatile oils it is highly important to include condensate that may be recovered from the gas produced from the reservoir. The volume of the hydrocarbon liquid condensed from the production of the solution gas that has been liberated. in some reservoirs may equal or even exceed the volume of recoverable stock-tank oil as estimated by present methods. The usual procedure1, 2, 3 in estimating future reservoir performance includes use of relative permeability data of the reservoir rock to gas and oil and includes material-balance calculations utilizing data on the volume of the reservoir fluids, oil and gas production and reservoir pressure decline, and data on the physical properties of the initial reservoir fluids. The inaccuracy in the procedure results from the false assumption that all of the free or liberated gas that enters the well bore of reservoirs containing highly volatile oils remains in the gaseous phase as it is produced. This paper presents a method for estimating future reservoir performance and oil recoveries based on special labora. tory analyses of reservoir-oil samples and recognition of the additional volume of hydrocarbon liquid that will be recovered at various stages of depletion from a solution.gas.drive reservoir. The method also includes calculations of the volume and composition of the hydrocarbon liquids that can be recovered by processing the produced gas in a natural-gasoline plant. The development of the method resulted from a study of laboratory analyses of reservoir samples and of field data obtained from two reservoirs containing oil of the highly velatile type. Relatively high pressures and temperatures prevail in oil reservoirs discovered at the greater depths of present-day drilling. The contained fluids may have high saturation -Dressures and large volumes of gas in solution. The oils and gases under these conditions may be almost identical in compositions and densities.4,5 Also, engineers have noted that, for a number of oil reservoirs and especially the deeper reservoirs, the API gravity of the stock-tank oil increaees as the production gas/oil ratios increase. They attributed this increase in API gravity of the stock-tank oil to the formation of condensate as the liberated gas in the reservoir is being produced. SOURCE OF DATA FOR CALCULATIONS Subsurface oil samples and well-test data were obtained from the E. Constantin-Lambert Well No. 1 in the Elk City Field, Okla., to demonstrate the need for and a method of calculating future reservoir performance when consideration is given to the recoverable hydrocarbon liquid from the production of solution gas that has been or will be liberated in a reservoir. The Lambert well is located in C, SW 1/4, SW 1/4, Set- 18, T-l0-N, R-20-W, Washita County, Okla. At the time of completion it was on the east edge of the development and Was producing from conglomerate through 30 perforations in the 5 1/2-in. casing at a depth of 9,859 to 9,864 ft. The well Was completed on July 9, 1949, and subsurface oil samples were obtained July 29 and August 1, 1949. Production gas/oil ratio data were obtained during the operation in series of two Separators at high and low-pressures of 314 and 44 psia, respectively, and at an average temperature of approximately 60°F. The flowing bottom-hole pressure at the time of sampling was 3,934 psis. The static bottom-hole pressure was not obtained at the time of sampling, as the well could not be shut in long enough for testing because gas produced from the well was used for fuel at an offset drilling well. However, the initial reservoir pressure was calculated to be 4,364 psia from knowledge of pressure gradients in other wells in the field and the depth of the casing perforations in the Lambert NO. 1 well.

Jan 1, 1951

By F. P. Bobrowski, G. B. Spencer, Alton B. Cook

In estimating production gas/oil ratios and oil recoveries from reservoirs containing highly volatile oils it is highly important to include condensate that may be recovered from the gas produced from the reservoir. The volume of the hydrocarbon liquid condensed from the production of the solution gas that has been liberated. in some reservoirs may equal or even exceed the volume of recoverable stock-tank oil as estimated by present methods. The usual procedure1, 2, 3 in estimating future reservoir performance includes use of relative permeability data of the reservoir rock to gas and oil and includes material-balance calculations utilizing data on the volume of the reservoir fluids, oil and gas production and reservoir pressure decline, and data on the physical properties of the initial reservoir fluids. The inaccuracy in the procedure results from the false assumption that all of the free or liberated gas that enters the well bore of reservoirs containing highly volatile oils remains in the gaseous phase as it is produced. This paper presents a method for estimating future reservoir performance and oil recoveries based on special labora. tory analyses of reservoir-oil samples and recognition of the additional volume of hydrocarbon liquid that will be recovered at various stages of depletion from a solution.gas.drive reservoir. The method also includes calculations of the volume and composition of the hydrocarbon liquids that can be recovered by processing the produced gas in a natural-gasoline plant. The development of the method resulted from a study of laboratory analyses of reservoir samples and of field data obtained from two reservoirs containing oil of the highly velatile type. Relatively high pressures and temperatures prevail in oil reservoirs discovered at the greater depths of present-day drilling. The contained fluids may have high saturation -Dressures and large volumes of gas in solution. The oils and gases under these conditions may be almost identical in compositions and densities.4,5 Also, engineers have noted that, for a number of oil reservoirs and especially the deeper reservoirs, the API gravity of the stock-tank oil increaees as the production gas/oil ratios increase. They attributed this increase in API gravity of the stock-tank oil to the formation of condensate as the liberated gas in the reservoir is being produced. SOURCE OF DATA FOR CALCULATIONS Subsurface oil samples and well-test data were obtained from the E. Constantin-Lambert Well No. 1 in the Elk City Field, Okla., to demonstrate the need for and a method of calculating future reservoir performance when consideration is given to the recoverable hydrocarbon liquid from the production of solution gas that has been or will be liberated in a reservoir. The Lambert well is located in C, SW 1/4, SW 1/4, Set- 18, T-l0-N, R-20-W, Washita County, Okla. At the time of completion it was on the east edge of the development and Was producing from conglomerate through 30 perforations in the 5 1/2-in. casing at a depth of 9,859 to 9,864 ft. The well Was completed on July 9, 1949, and subsurface oil samples were obtained July 29 and August 1, 1949. Production gas/oil ratio data were obtained during the operation in series of two Separators at high and low-pressures of 314 and 44 psia, respectively, and at an average temperature of approximately 60°F. The flowing bottom-hole pressure at the time of sampling was 3,934 psis. The static bottom-hole pressure was not obtained at the time of sampling, as the well could not be shut in long enough for testing because gas produced from the well was used for fuel at an offset drilling well. However, the initial reservoir pressure was calculated to be 4,364 psia from knowledge of pressure gradients in other wells in the field and the depth of the casing perforations in the Lambert NO. 1 well.

Jan 1, 1951

By Keith R. Bock, Norman Parlee, Albert M. Barloga

Coils of pure iron and iron-carbon alloy wire (0.05 to 0.80 pct C) and sufficient sulfur to saturate the solid phase were equilibrated in evacuated or argon filled tubes. After rapid cooling, and removal of the outside nonmetallic layer, the wires were analyzed for carbon and sulfur and the data used to construct an Fe-S binary and isotherms of the Fe-C-S ternary in the range 1149° to 1427°C. THE solid solubility of sulfur in steel is of interest in connection with such phenomena as hot shortness, burning, and so forth. "Burning," the more or less permanent damage that some steels suffer when heated for forging or rolling, has been shown to be related closely to the behavior of sulfur and less closely to carbon and oxygen.' Attempts to interpret burning phenomena in steels fail because of lack of data on the Fe-C-S and the more complex systems in this family. Rosenqvist and Dunicz 2 and Turkdogan, Ignatowicz, and pearson3 have largely elucidated the Fe-S diagram in the region of interest but no information on the Fe-C-S diagram in this region appears to be available in the literature. This paper deals with the elucidation of the Fe-C-S diagram in these interesting ranges. The method employed is different from those used by previous workers2'3 on the Fe-S system. EXPERIMENTAL METHOD Pure iron wires (Ferrovac E) or iron carbon alloy wires of 1 mm in diam were cleaned with acid and acetone, coiled, and placed in silica tubes (7 mm OD and 5 mm ID) previously closed at one end. Enough sulfur was added to assure saturation of the solid iron phase. The filled tubes were either simply evacuated and sealed, or filled with argon at a reduced pressure and sealed. The argon was required at the higher temperatures to prevent collapse of the tubes. The filled and sealed tubes were placed in the middle uniform temperature zone of a Globar tube furnace and equilibrated at temperatures ranging from 2100°F (1149°C) to 2720°F (1493°C). After equilibration the tubes were removed from the furnace and quenched in air or water, the form of quenching being found to have no effect on the results. The tubes were broken open and the coils were placed in a 1 : 1 HC1 solution to remove the sulfide-rich layer. The coils were then cut into small pieces and analyzed for sulfur and carbon. In the early stages of the investigation different equilibration times ranging up to 17 hr were tried and the cores of the wires were analyzed to test for saturation. One hour appeared to be sufficient to reach maximum sulfur content at 1454°C and 2 hr sufficient at 1149°C. The practice adopted was to use at least 3 hr at the higher temperatures and at least 5 hr at the lower temperatures. The iron-carbon alloy wires used were made by carburizing pure iron wire with carbon monoxide gas in a one inch diameter ceramic tube at about 1204°C. Differing carbon contents were obtained by allowing fairly large coils to react with the gas for varying lengths of time at a flow rate of 800 cc per min. The reacting times ranged from 15 min to 4 hr depending upon the amount of carbon desired. The furnaces used were controlled by means of Leeds and Northrup Speedomax Type H instruments with D.A.T. Control attachment. Thermocouples were calibrated against the melting points of gold and copper. The temperatures recorded appear to be accurate within i2.7OC. Starting with run No. 85 and continuing with the

Jan 1, 1962

By C. Chu

A theoretical investigation has been made of the forward combustion process using a one-dimensional linear mathematical model, taking into consideration the effect of the vaporization-condensation which occurs on the leading edge of the heat wave. This work involves the solution of five coupled partial differential equations. Besides the vaporization-condensation phenomenon, these equations account for conduction, convection, combustion, heat loss, diffusion and bulk fluid flow. For the one-dimensional linear model studied, the vaporization-condensation phenomenon does not induce appreciable change in the temperature at the combustion front; and its primary effect is to create a steam plateau and to increase the length of the heated zone ahead of the combustion front. This effect becomes more pronounced at lower pressures, higher porosities or reduced gas saturations. The peak temperature and the temperature profile on the leading edge of the heat wave stabilize after a certain period. The length of the steam bank remains practically constant, although the length of the water bank increases as the heat wave advances. INTRODUCTION The existence of the vaporization-condensation phenomenon in the heat-wave process and the important role played by the phenomenon have been recognized by several investigators. Kuhn and Kochl stated that steam plateaus were frequently observed on the temperature records of their experiments. The steam plateaus were attributed primarily to the vaporization and subsequent condensation of the interstitial water existing in the oil sand. Szasz2 suggested that both lighter hydrocarbons and water are vaporized on the leading edge of the heat wave, carried forward in the gas stream, and then condensed to create banks of oil and water. Martin et al suggested that the vaporization-condensation phenomenon is one of the main mechanisms of the heat-wave process, along with thermal expansion and viscosity reduction. Wilson et al. reported the existence of a steam plateau several inches in length in their small-scale tube-run experiments. However, this important phenomenon has never been taken into consideration in the numerous theoretical analyses by various authors. 5 The purpose of this work was to study the thermal aspects of a linear heat wave, taking into consideration the vaporization-condensation on the leading edge of the wave, to determine the effect of this phenomenon on the temperature profile of the reservoir, and to investigate how this effect varies when other process variables are changed. THEORY We consider a reservoir of porous medium of cross-sectional area A, extending from x = 0 to x = L. This reservoir contains, aside from the solid matrix itself, a gas phase and a "combined liquid phase" which is a combination of two immiscible liquid phases — namely, an oil phase and a water phase. The oil present in the reservoir is assumed to consist of three fractions, a noncondensable gas, a nondistillable residuum, and a vaporizable oil fraction which may be present in both the gas phase and liquid phase. Before the heat-wave process begins, preheating has taken place and has imparted an initial temperature distribution T,(x) to the reservoir. At the start of the process, a stream of oxygen-bearing gas is introduced through the face at x = 0. This gas supports the combustion of the residual fuel and supplies the heat throughout the process. In order to develop a tractable system of equations, the model properties are postulated as follows: (1) the system is isotropic and homogeneous; (2) there is a uniform fuel content throughout the reservoir; (3) combustion takes place in a moving vertical planar region of infinitesimal thickness; (4) the temperatures of the fluids and the solid matrix are identical; (5) radiation is negligible; (6) the gas and liquid saturations are uniform throughout the reservoir and remain unchanged

Jan 1, 1965

By J. Fageant, W. C. Ellis

All major regions in a progressively solidified germanium ingot were related through successive orders of octahedral twinning. The occurrence of lineage structure and the generation and survival of orientations are discussed. WHEN metals solidify in a temperature gradient a preferred orientation, or casting texture, usually develops. For example, in face-centered and body-centered cubic metals, most of the solidifying crystals have a cube axis, <loo>, aligned approximately in the freezing direction.&apos; In the solidification of diamond cubic metals this is not the case, since there is a natural tendency to form twin orientations.&apos; . In this paper, twinning relationships in cast germanium are described; some conclusions with respect to nucleation and survival of new orientations are discussed. In the first experiment, an ingot of high purity germanium, % in. in diameter and 1 % in. in length, was formed by progressive solidification4 from the bottom. The ingot was cut into 21 slices, each circular and about 0.030 in. thick. The top surface of each slice was polished and etched to reveal the regions of different orientations. Orientations were determined by the Laue X-ray back-reflection method. The uncertainty in the determined orientation relationships was l" or 2" when separate slices and films were involved. Frequently, however, advantage was taken of illuminating across a boundary when the patterns of the two orientations were recorded on the same film. The uncertainty then was less than 1". Often the twin relation was evident from common zones or individual reflections. Twin relationships were recognized through comparison of the values of the nine angles between cube poles of the two orientations with those calculated for successive orders of octahedral twinning. The birth and survival of each region can be reconstructed by visual examination of the etched slices shown in Fig. 1. In slice 21, where solidification began, many regions are present; these regions were found to be twin-related. Solidification appears to have started from one nucleus formed probably at the wall of the crucible.* Subsequent ori- entations were developed by nucleation on existing solid surfaces, and only in the twin relationship. This is an example of a general process of nucleation on a surface of existing solid and may be descriptively termed oriented nuc1eation.t In germanium, and other diamond cubic substances, the orienting habit is that of twinning on an octahedral plane.&apos; " The prevalence of straight traces in the polished surfaces of succeeding slices (Fig. 1) suggests that the twinning observed in the first slice persisted throughout solidification. This was confirmed by X-ray determinations. The schematic diagram of Fig. 2 shows the twinning relationships of the major regions throughout the ingot. Since all observed relationships are describable as twinning, it is reasonable to conclude that no random nucleation occurred in the freezing of the ingot. An alternative possibility would be that nucleation of a random nature occurred, but only those nuclei in twin orientations survived in subsequent growth. This is unlikely for there would be as good a reason for the growth of randomly oriented nuclei as for the growth of the many different orientations present after several orders of twinning. The many twin components contain a wide distribution of orientations, and did grow. In fact, they are the only ones found in the solid. The conditions of solidification of this ingot were such as to discourage nucleation of crystals wholly in the liquid. The rate of solidification was 0.125 in. per min. This slow rate of heat removal afforded but small opportunity for supercooling within the liquid —a condition needed to provide enough decrease in free energy for such nucleation. When nucleation occurs on an existing solid surface, the interfacial energy between the existing and forming regions is important in determining the new stable orientation. The new orientation is expected to be one which minimizes this energy. In the diamond cubic structure, the interface for the

Jan 1, 1955

By R. J. Weege, A. W. Schillinger

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. The work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept, as advanced by earlier writers to explain the concentration of the ore-bearing fluids into broad shoots constituting entire ore bodies, is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body. Recently, the Calumet Division of Calumet and Hecla, Inc. completed the unwatering of the old mine workings on the Osceola amygdaloid. Two shafts were subsequently reactivated and mining commenced on the Osceola lode after an idle period of over 20 years. Early in 1961, the Calumet and Hecla Geological Dept. was assigned the task of locating additional reserves. Accordingly, an intensive mapping and underground diamond drilling program was initiated. Except for a very few years following the first mining on the amygdaloid, the Osceola lode had never been a high grade producer. It was, therefore, recognized from the onset that a concentrated effort would have to be made by the mining, milling, and geological departments to insure success of the project. Company reports contained many references to ore that had been located near the footwall of the Osceola amygdaloid. Information concerning the grade of this ore was meager, but it was known that at least some was very rich. In contrast to ore that occurred near the hanging-wall, however, the footwall copper did not appear to have a systematic distribution and a large amount of poor rock had to be removed in developing this ore. This, of course, resulted in high development costs and discouraged any extensive mining of footwall ore. The possibility of more continuity than had previously been suspected was recognized by other workers, in particular Dr. T. M. Broderick, formerly Chief Geologist of Calumet and Hecla, who suggested attempts be made on a trial basis to follow the footwall contact with the main development drift. As most mining was done on the Osceola lode before a geological department had been established by the company, and almost all of these openings are now caved, very little information concerning the geology of footwall ore was available. It was, therefore, decided that the first step in the exploration program would be to become familiar with footwall ore occurrences by mapping the geology as the openings were driven. It was possible that a mapping program would reveal the features that controlled the localization of the ore. Furthermore, if it could be shown that footwall ore was more continuous, or if its distribution was more systematic than generally believed, it would be possible to produce a high grade ore that could be blended with the lower grade hanging-wall ore. In connection with the geological program, the Michigan College of Mining and Technology Geophysical Dept. under the direction of Professor Lloyal Bacon, is making a geophysical study of the problems of locating footwall ore by electrical methods. GENERAL GEOLOGY OF MICHIGAN NATIVE COPPER DEPOSITS The native copper deposits of Michigan are located in Keweenaw, Houghton, and Ontonagon Counties. The host rocks are Keweenawan in age and are comprised of interbedded sediments and lava flows which form a belt two to four miles wide and over one hundred miles long. These rocks form part of the south limb

Jan 1, 1962

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,&apos; these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton&apos; have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth&apos;s magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the in-trusive~, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust,&apos; these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure. The particular intrusive studied is located about 1 mile north of the small town of Avon at an elevation of 880 ft in the EVz SEy4 NEY4 of see. 2, T. 35N, R. 7E. Outcrop is through the Bonneterre dolomite in two separated exposures. The larger outcrop extends east and west for about 50 ft along a tributary in a small ravine (fig. 2). The smaller exposure occurs as a few scattered patches over an area 20 ft square about 100 ft to the north. The area between the exposures is covered, but scattered patches of the Bonneterre dolomite outcrop throughout the area surrounding the diatreme. Where exposed, contact relations show the surrounding dolomite to be shattered and metamorphosed to a fine-grained rock for a distance of 15 to 20 ft from the intrusive. The igneous rock occurs as a dark greenish-gray porphyry near the center of the diatreme and as a fine-grained, greenish-gray material containing lapilli and metamorphosed fragments of dolomite near the contact with the country rock. The most abundant original mineral of the porphyritic rock is olivine now largely serpentinized as the result of extensive hydrothermal alteration at time of emplacement. The most common constituent of the fine-grained rock, which occurs near the border of the intrusive, is calcite. Mica is a common constituent of both types of rock, occurring as tufts or flakes. Magnetite makes up about 2 pct of the diatreme and occurs as small irregular grains or streaks of tiny grains. Singewald and Milton&apos; have termed the rock of this body an "augite-free alnoite." Susceptibility measurements of pulverized specimens were made from selected samples taken from both the diatreme and the surrounding country rock. The susceptibility of the Bonneterre dolomite was found to be less than 40xlO-6 cgs (centimeter-gram-second) units and that of the metamorphosed contact dolomite less than 200x10-6 cgs. Measurements of individual samples of the igneous rock showed a wide variation in susceptibility between limits of 1000x10-6 cgs to 8000x10-6 cgs, with the maximum difference occuring in samples taken only a few feet apart. The maximum value was exhibited by a highly weathered sample taken from the northern outcrop, while minimum susceptibility was determined from a partially weathered sample taken only a few feet away. These extremes are believed to represent small local concentrations of stringers and grains of magnetite crystals in the igneous rock. A detailed magnetic survey of the horizontal and vertical components of the earth&apos;s magnetic field was made over the diatreme area. Stations were occupied at 20-ft intervals as shown by the grid on fig. 2. When greater detail was desired, intervening stations were also occupied. The field instruments were supplied by the Department of Geophysics, St. Louis University. The magnetometers are the Schmidt balance type constructed by the Ruska Instrument Co. These instruments are temperature compensated and have a standard sensitivity of 10 gamma. Calibration of the instruments

Jan 1, 1951

By Donald A. Corrigan, John Chipman

It is shown that the heat of solution of nitrogen in liquid-iron alloys is Proportional to the interaction coefficient. This proportionality forms the basis for a method of predicting nilrogen solubility at any temperature when the interaction coefficient is knoun at 1600°C ov when the solubility is known at some one temperature. A method for predicting the solubility of nitrogen in liquid steels, including alloy steels, was proposed some years ago by Langenberg.&apos; Since the data available at that time were restricted to temperatures of about 1600°C, his predictions were similarly restricted. More recently, Nelssonz devised an approximate method for estimating nitrogen solubilities at higher temperatures. It is the purpose of the present paper to present a method by which the solubility of nitrogen at any temperature within the steelmaking range may be predicted from the known interaction coefficients at 1600°C. Nitrogen in iron and in all of the alloys to be considered here is known to obey Sieverts&apos; Law; hence the activity of nitrogen in an alloy of fixed composition is proportional to its concentration, here expressed in weight percent. The activity of nitrogen is defined as equal to its weight percent in the binary Fe-N solution at any temperature. Its activity coefficient in any alloy is the comparison being made at equal values of T and PN2. In all alloys the activity coefficient changes with composition, log fN being a linear function of the percent of alloying element at low concentrations. In the following calculations the alloy compositions are restricted to those in which this linear relation is exhibited. For most systems this is a fairly wide range, for example up to 5 pct V and to 10 pct Cr or Ni. For this composition range. complex alloy is the same as that in the Fe-N-j ternary solution. Langenberg&apos;s method of prediction was based on Eq. [3], the values of log fN for various additions being taken from a graph. Instead of using the simple addition indicated in Eq. [3], he used a more complex method suggested for Fe-S-j alloys by Morris and Buehl.3 For the composition ranges in which Eq. [2] is valid the two methods are equivalent. Nelson extended the prediction to other temperatures on the assumption that logfN is inversely proportional to absolute temperature. It may be shown that inverse proportionality would result if the partial molal entropy of nitrogen were unaffected by addition of the alloy element, an assumption which Nelson designated as a "regular" solution. It has been shown recently by the authors4 that this assumption is not a good approximation. The heat of solution of nitrogen (N2) in an alloy may be obtained if the solubility is known as a function of temperature. Measurements of this nature have been reported recently by Beer5 for Fe-Mn alloys, by Nelsson2 for Fe-C, by El Tayeb and parlee6 for Fe-V, and by Pehlke and Elliott7 for many alloys embracing a wide range of compositions. In connection with the work of the last named authors it is noted that their Fig. 22 gives the heat effect per half mole rather than per mole of N2. In using their data we have shifted some of their values slightly by using the best straight line in preference to their curve. Their data, supplemented by others from the literature, are summarized in Table I. In Fig. 1 the heat of solution of nitrogen is shown as a function of composition for the several alloy systems. The difference between the heat effect in the alloy. AH; and that in pure

Jan 1, 1965