Search Documents

By J. R. Low, D. F. Stein

Single crystals of iron have been grown from three different lots of Ferrovac "E" of somewhat different chemical composition by the strain anneal technique. Using a technique to seed the crystal similar to Dunn's for silicon-iron, it has been possible to orient the crystals grown in both direction and plane of growth. Crystals having the plane of the strip oriented (100) , (110), (111), (112), (123), and (491) have been grown. The growth directions used have been [100], [110], 45 deg from a [110}, and various others of no specific crystal orientation. The usual dimensions of the crystals were 8 by 1 by 0.08 in. Attempts to grow crystals were about 90 pct successful. METHODS of growing single crystals of high purity iron have been reported in the literature.1-4 However, each of these methods was not completely reliable when used on materials having slightly different chemical composition and in some instances a small number of successes were obtained using identical materials. Except for the method used by S. Dohi and T. Yamoshita,1 it has not been possible to reorient single crystals of high purity iron to give any desired orientation. The method to be described has made it possible to grow single crystals from three different lots of material having different compositions, and to orient the crystals with respect to growth direction and surface. STARTING MATERIAL The material used during this investigation was a vacuum melted high purity iron marketed by the Vacuum Metals Corporation designated Ferrovac "E." Three lots of Ferrovac "E" having the following composition were used with equal success: The compositions listed are those of the as-received material; and they may have been modified before the growth of single crystals. Analysis of heat B just before growth and after growth revealed that the heat treatment prior to growth did not change the carbon content, but the oxygen content was changed from 0.0092 pct to 0.0034 pct and the nitrogen content from 0.0003 pct to 0.0001 pct. After growth of the single crystals, the carbon had dropped to 0.001 pct. None of the heat treatments would be expected to change any of the other impurities very markedly. Heat C would be expected to have a metallic impurity content similar to heats A and B. PROCEDURE Ferrovac "E" iron which had been obtained in bar form having a diameter of about 1 in. was rolled into strip for growing single crystals. By passing the 1-in. bar through a cold rolling mill several times, it was reduced to a strip 0.15 in. thick. The strips obtained were then cut into suitable lengths for heat treating (about 9 in. long), annealed at 925°C for 2 hr in dry hydrogen and water quenched. It was then necessary to bake the strip at 200°C for 24 hr in air in order to prevent cracking during further rolling operations. While it was possible to cold roll the 1-in. bar directly to the desired 0.080-in. strip, the intermediate anneal was used because the strip so obtained produced better single crystals. The strip obtained by rolling the 1 -in. bar directly to 0.080-in. strip produced single crystals having a large number of occluded grains. Experiments showed that the optimum reduction in area by rolling prior to the growth of single crystals was about 50 pct. Attempts to grow single crystals from material that had been reduced less than 40 pct were unsuccessful presumably because the matrix did not possess the critical amount of texture necessary for growth. The strip obtained after the rolling operations had very irregular edges which were ground to give a strip with uniform dimensions. The strip was then annealed at 825°C for 3 hr in hydrogen and furnace cooled. Fig. 1 illustrates the grain size obtained. A temperature of 940°C was used for the annealing temperature on one group of strips

Jan 1, 1962

By Richard Franchot

DISCUSSION of a paper is sometimes more in-teresting in what has not been said than in what is said. In the present case the paper is mainly directed to certain thermo-dynamic relation-ships in the blast furnace. Careful reading of the dis-cussion fails to show a single use of the term, heat unit, or its equivalent. If we wish to know very-much about the furnace action it is necessary to count calories or B.t.u. Nothing much is. said about the availability of heat at high temperatures, although it will be generally admitted that in seeking underlying limiting factors in the furnace economy the hearth heat relations offer-the most promising clues. Those discussing the paper, with exceptions of course, apparently have failed to recognize an outstand-ing fact. It is a fact that the heat actually generated by the air oxygen in CO formation (including the blast heat) is in excess, after charging off radiation, etc., by from 70 to .90 per cent over the heat absorbed in melting the iron and slag and calcining the stone reduction by CO absorbing no heat. The fact stands out as plainly as does the fact that the furnace functions largely as a gas producer. The surplus heat is there. It is in the picture. Why not take a look at it, face the fact? That the surplus heat is necessitated by the hearth conditions admits of very little if any doubt. The furnace is really two separate pieces of apparatus: the hearth, doing certain work, and the superimposed shaft, doing certain other work. The combustion of fuel in the hearth, primarily serving the hearth pur-poses, generates much more heat and gas than the shaft requires, or can use, in smelting work. The result is surplus heat makes still more gas in the heat-absorbing reaction between CO, and coke; what is left of the surplus going to top heat. Here we have a simple yet adequate sketch of the furnace action. Having obtained a fairly comprehensive view of the existing heat relations of both hearth and shaft, the way to improvement seems quite plain. Either do more of the work above the hearth or put more heat into the hearth. Since there is already a great surplus of heat above the hearth, probably little needs to be done by way of increasing the proportion of the work done in the shaft. The shaft can, however, probably do much more work than it is now doing provided that a way, can be found to get more work, done in the hearth. The hearth heat is nicely balanced. Losses by radiation and water cooling and other losses are already taken care of. Any increase of hearth heat development could be utilized in taking care of increased smelting work. Aside from the possibility of increased blast heat, there is one sure way of putting more heat into the hearth, and this is to blow more air. And since the shaft already has more gas than it needs, the increased gas resulting from the greater blast volume can be withdrawn from the bosh after it has done its work in the hearth. Now an increase of burden will cool the shaft, cut down solution loss and thereby supply addi-tional coke in the hearth to burn with the additional air blown. The hearth heat per pound of coke charged will be proportionately increased. The balance between hearth and shaft will be better. Gruener's ideal will be more nearly attained, if not exceeded. Most inter-esting of all perhaps, the more the burden is increased, the more coke will reach the hearth and the more burden can be added. The effect is to be cumulative.

Jan 3, 1927

By D. P. Harris

The construction of a model to associate probability of occurrence of some measure of mineral wealth with the geology for each subdivision (cell) of the area is postulated. The questions (1) are the observations made in reconnaissance geology sufficiently related to mineral wealth to distinguish the cells of high value from those of low value, and (2) can this geology be related mathematically to mineral wealth and probability are answered in a case study of 97,000 square miles in Arizona and New Mexico. Measurements on mineral wealth and geologic variables of 243 cells were made. The geologic variables, valued in counts, percentages and lengths, quantified the theoretical concepts of the model. It was found that multiple discriminant analysis and classification analysis by Bayesian statistics and multivariate normal probability function constitute a two-phase probability model that associates probabilities with geologic information and mineral wealth. The cells of explored area must be allotted the value class indicated by their cumulative production and estimate reserves (given well-defined geological relationships in a mineral wealth area), and a discriminant and classification analysis must be performed in which probabilities of the cell belonging to each of the value groups are generated as a function of the geologic variables. This determines whether high value cells can be distinguished from low value cells by their geology as well as indicating those cells misclassified by the model into a higher value group than warranted by their known mineral wealth. The second use of the model is for extrapolation. It is demonstrated how geologic information on an explored area can be utilized in guiding exploration in an unexplored area. Exploration decisions can be predicted on explicitly determined measures of uncertainty (the probabilities). SUMMARY This study postulates the construction of a model to associate probability of occurrence of some measure of mineral wealth with the geology for each subdivision (cell) of the area. Such a model will distinguish those cells deserving further exploration on the basis of their geology: The basic postulates of this study are as follows: v = Q(R,S,F,A) P(V) = G(R,S,F,A,V), where V = a measure of mineral wealth P(V) = the probability of occurrence of V R = age and type of rock F = rock fracturing A =age of igneous activity and contact relationships. There are really two questions to be answered: 1) are the observations made in reconnaissance geology sufficiently related to mineral wealth to distinguish the cells of high value from those of low value, and 2) can this geology be related mathematically to mineral wealth and probability? In order to answer these questions, an area of about 97,000 square miles situated chiefly in Arizona and New Mexico was selected as a case study. This case study area was divided into 243 cells, each 20 miles square, and measurements were made on mineral wealth and geologic variables. Crude geologic variables valued in counts, percentages and lengths are constructed to reflect the above postulated variables. These measurement variables thus provide quantified values defining the theoretical concepts of the model. It was found that multiple discriminant analysis and classification analysis by Bayesian statistics and the multivariate normal probability function constitute a two-phase probability model that associates probabilities with geologic information and mineral wealth. Given the availability of an area that is well explored and upon which the relationships of mineral wealth to geology can be adequately defined, there are two ways in which the analysis outlined in this paper can prove beneficial. First, the cells of the explored area must be allotted the value class indicated by their cumulative production and estimated reserves, and a discriminant and classification analysis must be performed in which probabilities of the cell belonging to each of the value groups are generated as a function of the geologic variables. Such an analysis determines whether cells of high

Jan 1, 1967

By C. Laird, C. E. Feltner

An investigation into the effect of a material's slip character on its high strain fatigue properties has been carried out using copper and Cu-7.5 wt pct A1 as representative wavy and planar slip mode materials, respectively. In copper, the constant term and exponent in the Coffin-Manson equation, ?EpNf1/2 = const, are unaffected by the temperature of testing or the history of the metal. On the other hand, in Cu-7.5 wl pcl Al, while the exponent is invariant, the constant is increased with respect to copper and increased further with decrease in temperature. The life in Cu-7.5 wt pct A1 is double that of copper at room temperature and about four times at 78°K. Fractoflaphic studies indicate that these diffevences in life are associated with the early stages of cracking. In copper, severe surface rumpling provides crack nuclei at pain boundaries independent of' testing temperature or the history of the metal. In Cu-7.5 wt pct Al, the planar slip mode of deformation prevents grain boundary folding; crack nucleation is therefore mainly transgranular and the increase in life with respect to copper is associated with a prolonged linking-up stage of such transgranulay cracks. At the lower temperature the increased difficulty of cross slip inhibits multiplication of trans-granular cracks and retards the linking-up process, giving a further enhaancement in life. It is expected that such behavior will be found general in materials of wavy and planar slip mode, respectively. STAGE II crack propagation in high strain fatigue takes place by a repetitive process of crack tip blunting in the tension part of a fatigue cycle followed by resharpening of the crack in the compression part.1-3 This mechanism has come to be called the "plastic relaxation process".3 At very high strains (lives to failure less than 103 cycles), most of the life of a specimen is spent in crack propagation by the plastic relaxation process.4,5 Since the differences in the cyclic strain hardening behavior of metals and alloys are comparatively small in this strain range,6,7 the amount of blunting at a crack tip depends primarily on the applied strain amplitude. The rate of crack propagation in this life range is therefore nearly constant with respect to material and temperature of testing. In the longer life portion of the high strain fatigue range (l03 to 103 cycles to failure), a considerable fraction of the lives is spent in crack initiation and Stage I growth. Grain boundaries have frequently4,5,8 been found to be the sites for this growth which is also associated with a surface folding process.4'5 Such folding behavior may also be general in any material having a grain structure and capable of plastic deformation. It has therefore been suggested475 that the universality of the Coff in-Manson law,9'10 constant,* where ?Ep is the plastic strain range and Nf the number of cycles to failure, is reflected in the approximate invariance of both the crack initiation and propagation behavior. It happens that, in most investigations of the phenomena associated with failure,4,5,8 materials with a wavy slip mode have been used as vehicles for the studies, or else "normally" planar slip mode materials have been tested under conditions giving rise to wavy glide deformation, e.g., stainless steels cycled at high temperature.'' The purpose of the present investigation was to determine whether or not different cracking phenomena would occur when the slip mode of a material is planar and if the associated life to failure would be different than that of a wavy slip

Jan 1, 1968

By R. R. Boucher, O. J. C. Runnalls

A pronounced thermal effect has been observed on heating or cooling a1wninum-rich Al-U and Al-Pu alloys. From microscopic and X-ray diffractionstudies, the effectl has been attributed to trnsfor)nations in the inlemetallic phases UAl, and PuAl , involuing rearrangement or cluslering of vacancies The transformation obsrved in Al-20 wi oct U alloys occurred near the a Al-UAl4 eutectic tem-perature of 646°C making it difjicult to detect from heating curves. When cooling, howeoer, thermal mad X-ray analyses indicnted that the high-temperati~re phase labeled p UAL, precipitated initially during euitectic solidification. As solidification continued and after an induction period o-f 5 lo 20 tnin the nu-cleatiorz and growth of the low- twmperature phase, a UAl4 produced an euolution of energy which raised the observed alloy temperature by 1° to 2°C. in Al-Pu alloys the transformation occurred at 645°C, 5 deg below the eutectic solidification temperccture. The eslimated latent heat of transformation was 25 +5 cnl per g PuAl,. The high-tetnpevcl-ture forms of UAl, and PuAl, were easily 9-etccined by chill casting Al-U and Al-Pu alloys and on reheating the alloys the trcltzsforrnation to the a phase was sluggish even above 600°C. Separated single cryslals o-f UAl4, joy example, showed no evidence Of transformalion after heating for 16 hr at 620°C. The transformation rates increased yapidly enough with increasing temperature, however, that a a spontaneous liberation of energy lens observed on occasion when bealing cast Al-20 wt pet U to neal- the RECENT phase studies on A1-Pu alloys have indicated that earlier reported equilibrium diagrams should be modified to take account of several poly- morphic transformations in the intermetallic compound PuAl,.' During the course of the latter work an unexpected heat evolution was observed while cooling a solid alloy consisting of a mixture of a aluminum and PuA1,. The evolution occurred at 645°C, y below the a A1-Pu A1, eutectic solidification temperature. Subsequent thermal-analysis experiments with A1-U alloys showed that heat was evolved there also at a temperature nearly coincident with the a A1-UA1, eutectic solidification temperature of 646°. A search of the literature revealed that similar thermal effects had been observed before for both A1-U and A1-Pu but had never been fully explained.2,3 The purpose of the present paper is to describe thermal-analysis and X-ray diffraction experiments which have led to the conclusion that the thermal effects are due to transformations which involve the rearrangement of vacancies in the intermetallic compounds UA1, and PuA1,. EXPERIMENTAL PROCEDURE The A1-U alloys were prepared by heating super-pure aluminum (99.99 pct +) obtained from the Aluminum Co. of Canada in a graphite crucible surrounded by an induction coil. At 1000°C high-purity uranium metal produced by the Eldorado Mining and Refining Co., Ltd. was dropped into the liquid aluminum and was dissolved completely within 15 min. The impurities in the uranium were A1—4 ppm, Ca-4, C-70, Cr-3, Cu-6, Fe-30, Mg-2, Mn-10, Ni-25, Si-25, and Zn-2. The A1-Pu alloys were prepared by reacting plutonium dioxide with liquid aluminum under cryolite (3 NaF . AlF,) for 10 min at 1100°C in graphite crucibles exposed to the air. The plutonium was 99.8 pct pure, containing trace impurities of Ca, Cu, Fe, Pb, Si, and Zn. The liquid alloys were usually poured into water-cooled molds to provide castings of uniform composition from which samples could be cut for heat treatment and thermal-analysis experiments.

Jan 1, 1965

By G. R. Speich, D. J. Mack

The transformation of was studied by isothermal methods. At all temperatures, the ß transforms quickly to fine grained ß" which develops silver-rich striations. At higher temperatures the striations disappear, the final structure being Widmanstatten a in ß'. At lower temperatures, the striated ß" is consumed by pearlite nodules of a + ß' which in turn form the Widmanstatten a in ß'. The transformation is unlike any previously reported for a eutectoid. AS part of a general program of study on the eutectoid reaction, the Ag-Cd eutectoid seemed particularly attractive because the ß phase which undergoes the reaction is another of the typical "electron compounds," AgCd, having the disordered body-centered cubic structure. This work deals with the eutectoid which occurs at 50.5 wt pct Ag, and not with the eutectoid which has been reported at 42.9 pct Ag.' There has been no work reported specifically on the Ag-Cd eutectoid which was studied. The only information available on this eutectoid is that work done in the determination of the phase diagram. For the most part, the terminal portions of the diagram, Fig. 1, are well established; however, the region from 40 to 60 pct Cd is still somewhat in doubt. The X-ray evidence'..' in this region is in conflict with the results of thermal analysis. X-ray analysis3 does not show a polymorphic transformation at about 240°C as indicated by thermal analysis.1,5 Even the X-ray evidence, within itself, is confusing in this region of the diagram. One investigator2 reports the ß phase as hexagonal close-packed and has found three phases in the one-phase ß field. Other X-ray investigators"' ' report the ß phase as body-centered cubic. The authors believe that much of the confusion resulted from incomplete homogenization of the alloys. It was found that it takes almost a week to produce a completely homogeneous two-phase structure at 370°C. Another possible source of error is the volatilization of cadmium from the surface and cracks of the specimen during annealing with the possible formation of a cadmium-poor phase. The only metallographic data available on this eutectoid alloy are those of Durrant1 and Fraenkel and Wolff.5 his information is very limited. The phase diagram chosen as most nearly correct is that in the Metals Handbook," which is almost identical with the phase diagram suggested by Durrant.1 Materials and Procedure The alloy was prepared from high purity silver (999.5 plus fine) and high purity cadmium (0.02 Pb, 0.005 Cu, trace Fe). The metals were melted in carbon under a nitrogen atmosphere. Some cadmium was lost by volatilization but by remelting several times and adding cadmium a 200 g ingot of approximately eutectoid composition was obtained. Because the CdO fumes are quite toxic, the exit gas from the furnace was led through a water trap to condense the CdO. The ingot was homogenized at 650°C for 24 hr, no attempt was made to prevent decadmiumization. This resulted in a narrow decadmiumized rim on the ingot which was removed. Filings for analysis were obtained from cross sections of the ingot. Silver was determined by the Volhard thiocyanate method,? cadmium by difference. The ingot analyzed 50.8 pct Ag at the top of the ingot and 50.7 pct at the middle and at the bottom of the ingot. This alloy was only slightly hypo-eutectoid compared to the accepted value of 50.5 pct Ag and was used for the isothermal studies. It was felt that further attempts to adjust the composition might be futile because of the volatility of the cadmium. The ingot was sectioned to specimens approximately 3/4 x 3/4 x 1/8 in. These specimens were "austeni-tized" for 3 hr in air at 650°C to yield homogeneous ß and then quenched into a salt bath held at constant subeutectoid temperatures where the transformation

Jan 1, 1954

By William C. Hagel

Oxygen-18 exchange between gaseous oxygen, held at a pressure of 125 mm Hg in a PL-IORh chamber, and splzeres of a Fe2O3 containing three or less grains was determined from 9000 to 1250°C. Isotope equilibrum on crystal surfaces appears to be quickly established, and the rate-determining factor is self-difiusion confbvrning to the relation D = 2.04 esp(- 77,900/RT) sq cin sec-'. Changing sphere diameters caused no detectable variation in diffusion coefficients. Oxygen ions diffuse faster than cations at low temperatures, but a crossover may occur at about 1150°C. INVESTIGATIONS by Davies et al.' and Himmel et al2 have suggested that the mechanism of iron oxidation above 600°C involves a predominance of cation migration in the wüstite (FeO) and magnetite (Fe301) layers and oxygen-ion migration in the hematite (a Fe2O3) layer. Evidence for little cation migration during hematite growth consists of: 1) the disappearance of radioactive-silver markers, presumed to vaporize from the oxide-gas interface, and 2) a large discrepancy between parabolic rate constants for magnetite oxidation and those calculated from Lindner's3 data for cation self-diffusion, D:, using Wagner's theory.4 Reversing the calculations gave anticipated self-diffusion coefficients, D:, for oxygen ions of 3.6 x 10-9 sq cm sec-1 at 1100°C and 5.9 x 10-10 sq cm sec-1 at 1000°C. Since then Kingery et a1.5 reported three values for oxygen-ion diffusion in polycrystalline, sintered hematite. These were obtained near 1200°C, at an oxygen pressure of approximately 150 mm Hg, and could be represented by the Arrhenius expression, Dg = 1 x 10 11 exp(-146,000/RT) sq cm sec-1. Extrapolation to temperatures below 1100°C infers that oxygen ions are less mobile than cations. This contradicts the aforementioned oxidation evidence and also coble7s study of the initial sintering of hematite. From the latter, apparent diffusion coefficients for the slowest rate-controlling species could be calculated, and fair agreement was found with an extension of Lindner's data for cation diffusion. Fig. 1 depicts such comparisons graphically. Three points have been included for the determinations of Himmel et al. on cation diffusion in large, natural hematite crystals surrounded by pure oxygen at atmospheric pressure. No dependence on crystal log raphic direction was noted. Since the value of 10-l4 sq cm sec-' at 1000°C actually represents an upper limit, one might interpret that there is a small decrease in D: when single crystals are employed. On the whole, however, cation diffusion appears relatively well-defined,* while the few results tension to lower temperatures. After having gained experience measuring oxygen-ion diffusion in certain glasses7 and in the corundum oxide, a Cr2O3, the purpose of this work was to determine D; values for hematite and thus possibly assist a mechanistic understanding of the kinetics of the oxidation and reduction of solid iron oxides. I) EXPERIMENTAL PROCEDURE A) Material. Hematite powder of moderately high purity was received from the Columbian Carbon Co. An accompanying lot analysis listed 0.03 H2O, 0.008 weight percents, with the remainder Fe2O3. Subsequent treatments were ball milling, drying, prepressing, and hot-pressing for 60 min at 1350°C under 5000 psi. Since graphite dies coated with a slurry of alumina were used for hot-pressing, the surrounding atmosphere at temperature was sufficiently reducing to form some magnetite on the outer surface of each cylinder. After removing any attached alumina, a stabilizing anneal of 50 hr at 1300°C in oxygen was added. The final product was nonmagnetic and exceeded 97 pct of the density (5.24 g cm-3) usually given for FezO3. On polishing cylindrical ends, counts were made of the number of grain boundary intercepts per

Jan 1, 1967

By D. L. Albright, G. A. Colligan

An investigation has been conducted to determine the nature of the crystallographic substructure of nickel and a 1.0 wt pct Ag-Ni alloy which had been undercooled 105°C prior to solidification. A rotating back-reflection X-ray technique and modified Weissmann diffractometer were used to orient single-crystal sections from these poly-crystalline ingots and to determine the substruc-tural features of these single crystals, The sub-grain size in the pure nickel ingot is 0.5 mm diam while the silver-doped nickel subgrain size is only 0.1 mm diam. The misorientation between adjacent subgrains is approximately 1 deg of arc in both ingots, and the spread of orientation of sub-grains about the mean orientation of the crystal is 5 deg of arc in both ingots. The addition of silver results in a stable impurity substructure which is preserved during isothermal solidification and subsequent cooling to room temperature. In the absence of silver the initial impurity substructure is destroyed by dislocation interactions which produce a secondary substructure which grows to a size five times larger than the initial substructure. THE process of undercooling a metal entails cooling of the molten sample below the equilibrium freezing point without the occurrence of solidification, i.e., by exercising proper constraint over the experimental variables contributing to nucleation in the melt. The current work of walker1 and Colligan Metal reports undercooling large continuous samples of nickel by imposing appropriate restrictions upon the parameters of solidification. The silver-nickel equilibrium diagram3 reveals the presence of a monotectic reaction at 1435°C. At this temperature the maximum solid solubility of silver in nickel is approximately 3 wt pct, but this solubility decreases with decreasing temperature and the solute is rejected as a silver-rich liquid phase at temperatures below 1435°C. Thus, the 1.0 wt pct solute should be held in solution during undercooling and solidification and subsequently precipitate as a silver-rich liquid phase at grain and subgrain boundaries following solidification during cooling below 1435. This assumes no solute segregation sufficient to cause the monotectic reaction. One would expect this second phase to inhibit grain and subgrain growth by retarding dislocation motion after solidification is complete. The effectiveness of silver addition in growth retardation of high-angle grain boundaries has been demonstrated by Colligan and suprenantS4 The principal [l00] dendrite growth directions in a 2 wt pct Ag-Ni alloy undercooled 53 all radiated from the nucleation site. A similar pure nickel ingot undercooled 59°C exhibited a random orientation of [l00] dendrite directions with respect to the nucleation site. Since undoped nickel ingots do not retain any evidence of the casting or solidification texture and silver-doped ingots do retain this texture, it is reasonable to assume that considerable grain growth has taken place in the pure nickel. These particular experiments were performed in order to reveal the differences, if any, in the features of the crystallographic substructure of undoped undercooled nickel and silver-doped undercooled nickel. 1) EXPERIMENTAL PROCEDURE Data are reported on selected specimens from two massive (approximately 260 g) undercooled ingots of nickel. One ingot consisted of electrolytic nickel and the other of this same material with 1.0 wt pct addition of high-purity silver. Powder patterns were taken of both the as-received and as-solidified materials; in all cases the reflections recorded were attributable to the individual elements nickel and/or silver. Fig. 1 is a. schematic diagram of the apparatus employed for the undercooling experiments. The equipment consists in part of a fused silica crucible for containing the charge. A fused silica tube encloses the system, which is covered by a brass cap to permit partial sealing of the inert atmosphere. This cap contains a hole through which a Pt-Pt 13 pct Rh thermocouple is inserted for temperature measurement. The charge is inductively heated under a purified argon atmosphere.

Jan 1, 1963

By P. L. Raffo, T. E. Mitchell

Single crystals of Ta-Re alloys have been deformed in tension and compression as a function of solute concentration and temperature. The temperature dependence of the yield stress is decreased by alloying. At low temperatures there is a minimum in the yield stress (at about 2 at. pct) as a function of concentration. Three-stage hardening was not observed in the alloys. Linear hardening rates, where observed, were characteristic of stage II in pure tantalum. At low temperatures and high concentrations, work softening was often prominent at high strains. Electron microscopy revealed that dislocations are mostly of screw orientation, although heavily jogged and cusped, and often occurring in dipole pairs. The alloys become more prone to cleavage with increasing rhenium content, due mostly to an increasing yield stress rather than a change in cleavage strength. Alloying apparently decreases the Peierls stress of bcc metals at low temperatures by facilitating kink nucleation at solule atoms on screw dislocations. Higher solute concentrations further increase the yield stress. Quantitative calculations and comparisons with other bcc alloy systems are made to show that the predominant hardening mechanism is due to the interaction of dislocations with misfitting solute atoms close to their slip planes. The interaction is so localized that the core dilatation of dislocations could be important. CONSIDERABLE interest has arisen in recent years concerning the mechanical properties of unalloyed bcc metal single crystals.'-7 These and similar studies on polycrystalline materials have resulted in a considerable understanding of the macroscopic yielding characteristics8, 9 and the process of work hardening.'' This latter advance is due in a large part to the increased use of transmission electron microscopy in P I RAFFO junior Membar AlMF is Metallyureist Iewis such studies and the general observance of three stages of work hardening in the shear stress-shear strain curves. The properties of substitutional alloy single crystals of bcc metals have not been determined in as much detail as in the pure metals. Insufficient systematic studies have been made on the effect of alloying on the magnitude and temperature dependence of the yield stress or the stress-strain curves. The alloy systems which have been studied to some extent have been Ta-W,11, 12 Ta-Mo," Ta-Nb,12'14 Mo-Re,15 W-Re,16 and alloys of iron with nickel,17 platinum,17 vanadium,18 and aluminum.18 A large body of data exists on Fe-Si alloys, but these have mainly been a result of the experimental convenience of using this material in place of unalloyed iron, rather than a comprehensive study of the mechanical properties of the alloy system per se. The present authors have previously reported additional data on the properties of Ta-Re, Ta-W, and Ta-Mo alloy single crystals.1g Some of the data on Ta-Re alloys will be described later in this paper. Briefly, single crystals of Ta-Re (1.2 to 10.6 pct), Ta-W (6.2 and 10.2 pct), and Ta-Mo (2.9 and 9.0 pct) were grown by the floating zone method in vacuum. Compression tests were performed in the temperature range 77" to 623°K. Slip was found to occur in Ta-Re alloys at 77' and 298°K on the (~ll)[lil] system and slip lines were coarser and straighter than in unalloyed tantalum. No three-stage hardening was observed in any of the alloy systems and the curves were nearly parabolic. At temperatures above 175°K the yield stress* increased monotonically with in- creasing composition while at 77" and 175°K the yield stress initially passed through a minimum after which it began to increase again for concentrations greater than about 2 pct Re. Similar minima were observed in Ta-Mo alloys and to a lesser extent in Ta-W alloys. The minimum was interpreted as being a result of a

Jan 1, 1969

By R. R. Webster, H. T. Clark

The side-blown converter has been investigated as a possible commercial process for the production of low nitrogen steel. During this work, two converters of 3-ton and 22-ton capacity were operated on a pilot plant basis for a total of 214 heats. The steel made in these converters was low in nitrogen and possessed good cold working properties. Some problems of converter operation remain to be solved. IN plants operating with a high iron capacity, sev-eral different refining methods are used in the conversion of the molten pig iron to steel. These include various ore practices in stationary and tilting open-hearths, the duplex process employing the Bessemer converter and open-hearth, and the Bessemer process. At J&L, a considerable part of the iron produced is handled by the Bessemer process, either alone or in conjunction with duplexing, and therefore an appreciable portion of the steelmaking research effort has centered about the method. This paper covers research work on the development of the side-blow converter for the commercial production of low nitrogen ingots and includes descriptions of the operation of a 3-ton and a 22-ton experimental converter at the Aliquippa Works. The refining of iron to produce steel requires the removal of a large portion of the carbon and silicon and the control of manganese, phosphorus and sulphur which are present in the iron in varying amounts. The first large-scale means of refining iron was the acid Bessemer process which was brought into use almost 100 yr ago. This method, using compressed air as the refining medium, accomplishes substantially complete removal of carbon, manganese and silicon. Phosphorus and sulphur are not affected but, by choice of an iron composition sufficiently low in these elements, a commercial product can be produced. Since the process will handle large tonnages rapidly, operates without external fuel and with a minimum of additional equipment, it quickly became the major tool in the early expansion of the steel industry. Later, the basic open-hearth process, by affording control of phosphorus and sulphur and by consuming the large quantities of steel scrap that were becoming available, forced the acid Bessemer process into a secondary position in the industry. During the past two decades the demand for steel to be used in cold forming and drawing operations has gradually increased. Bessemer steel, because of its work hardening and aging characteristics, is not as suitable for these applications as basic open-hearth steel, consequently the decline of the process was accelerated. More recently, because of changing economic conditions, this long range trend appears to have been arrested or perhaps reversed. Ingot production data for recent years furnishes only an incomplete picture of the importance of the converter in the American steel industry; open-hearth furnaces utilize large tonnages of blown metal for which no published statistics are available. Metallurgical Aspects The fundamental difference between Bessemer and open-hearth steels apparently lies not in the method of manufacture but, rather, in the differences in chemical composition of the two steels. It is further believed that the principal features distinguishing Bessemer from open-hearth steel are the higher nitrogen and phosphorus contents of the former. Evidence supporting this position is supplied by tests on laboratory induction furnace heats that were made to contain varying amounts of phosphorus and nitrogen but were otherwise similar to normal low carbon silicon-killed steels. Fig. 1, 2 and 3, summarizing the test results, are taken from G. H. Enzian's paper titled, "Some Effects of Phosphorus and Nitrogen on the Properties of Low Carbon Steels."' Fig. l indicates that phosphorus has a marked effect on the cold work embrittlement of steel as shown by the work brittleness test of Graham and Work.' In the low nitrogen steels, which as a group have the better cold working properties, the effect of phosphorus variations is the more pronounced.

Jan 1, 1951

By C. H. Li, R. J. Stokes, T. L. Johnston

The phenomenon of solid-solution strengthening has previously been studied in a number of binary alloy systems.1-8 There has been, however, very little information published concerning the strengthening effects of specific solutes in magnesium alloys. Schmid and his coworkers9,10 investigated the behavior of aluminum and zinc in binary and ternary magnesium-alloy single crystals, but this work was done before high-purity materials were readily available. Workers at the Dow Chemical companyH reported increases in the critical resolved shear stress upon alloying magnesium single crystals with zinc and indium. Recently, Hardie and parkins* investigated the extent of hardening produced by the addition of various solutes to poly crystalline magnesium. The present work was undertaken to provide data on the strengthening effects of a number of solutes in high-purity magnesium, for the purpose of supplying further experimental information which might be useful in describing a general mechanism for solid-solution strengthening. To simplify interpretation of the results, the mode of deformation was limited to basal slip, through the use of single crystals. EXPERIMENTAL PROCEDURE Magnesium and magnesium binary-alloy single crystals containing indium, cadmium, thallium, aluminum, and zinc were prepared in the form of l/2-in.-diam rods, approximately 8 in. long, using a modified Bridgman technique in which the crystals were slowly cooled from the melt in a steep temperature gradient, in an atmosphere of helium. It was found that a solid-liquid interface travel speed of about 0.7 in. per hr consistently produced single crystals. The poly crystalline starting materials for the preparation of single crystals consisted of 1/2-in.-diam extruded rods, prealloyed to the desired composition. The unalloyed magnesium and magnesium-indium extrusions were furnished by the Dow Chemical Co. The other alloys were prepared at the Rensselaer Polytechnic Institute Metallurgical Laboratories. Some preliminary studies of the strengthening effect of indium were conducted at room temperature using a constant rate of tensile loading of 1040 g per min. Stress was applied to the crystals by means of a simple 5:l lever arm. The lever was loaded by a constant rate of flow of shot into a receptacle suspended from the long arm of the lever. Plastic flow was detected by an electrical resistance strain gage cemented to the surface of the crystal normal to the minor axis of the predicted glide ellipse. The crystals were acid machined to produce tensile specimens with a reduced section between the grip ends, with an additional step in the center of the reduced section to compensate approximately for the slip-retarding effect of the strain gage. The balance of the single crystals were extended in an Instron tensile tester. This machine employs a synchronously driven screw and automatically records applied load as a function of cross-head separation. It became unnecessary therefore, to employ a strain gage to detect deformation or to acid machine a reduced section. Preparation for testing reduced merely to chemical cleaning of the surface, thus minimizing the amount of handling and probability of accidental damage to the crystals. The rate of elongation employed in all the tests was 0.002 in. per min, corresponding to a strain rate of approximately 0.0004 per min. EXPERIMENTAL RESULTS The investigation confirmed the finding of many workers that the yield strength of hexagonal metal crystals is strongly orientation-dependent. This is illustrated in Fig. 1, in which o, the tensile stress required to produce gross plastic flow in eleven unalloyed magnesium crystals stressed at a constant rate of loading is plotted as a function of sin X, cos Ao where X, is the angle between the

Jan 1, 1960

By P. H. Turnock, R. D. Pehlke

The effects of mutual interactions between elements on the solubility of nitrogen in liquid iron alloys containing chrormium, columbium, molybdenurn, nickel, or silicon have been determined. The equilibrium nitrogen solubilities in the liquid iron alloys were measured by the Sieverts method. The second-order effects caused by the presence of chrormium, columbium , or silicon in the melt were found to be significant. The solubility of nitrogen in liquid iron alloys containing several alloying elements has also been measured as a function of melt temperature and nitrogen pressure. The heat of solution of nitrogen in microcomponent iron alloys has been found to be a function of the logarithnz of the activity coefficient of nitrogen, irrvespectilje of the composition of the melt. The heat of solution of nitrogen in pure liquid iron was determined to be 1265 ± 450 cal per g-atom of N over the temperatxue range 1600° to 1800°. Sieverts ' law was obeyed for all melt compositions studied in the pressure interval 0.4 to 1.0 atm. The solubility of nitrogen in liquid pure iron and in many dilute binary liquid-iron alloys has been the subject of many investigations. Pehlke and Elliott' made a comprehensive investigation on this subject in which they summarized and compared previous researches. However, the practical application of these solubility studies requires prediction of the nitrogen solubility in the multicomponent alloys encountered in operating practice. The interaction parameter as defined by wagner2 has been used to predict the behavior of a solute in a complex alloy, and a modification of this approach has met with reasonable success in several instances.'1"5 The necessity for extending the nitrogen solubility data on binary alloys is caused by the lack of direct measurements of the solubility of nitrogen in molten alloy steels. A direct comparison between measured solubilities and those predicted for multicomponent alloys based on data in binary systems has been made in only a few instances, and most of these were reviewed by Langenberg,6 who developed a graphical technique for predicting nitrogen solubilities in multicomponent iron alloys. The solubility of nitrogen has also been studied over the entire Fe-Cr-Ni ternary system by Humbert and Elliott.? Both studies compared the solubilities computed from binary iron alloy data with those measured in ternary alloys in the liquid state at 1600°C. Most of the nitrogen solubility measurements referred to above were for iron alloys at 1600°C; thus, the ability to predict nitrogen solubilities in molten iron alloys has been restricted primarily to alloys at 1600°C. Recently, Nelsson8 devised an approximate method for calculating the change in nitrogen solubility in molten iron alloys as a function of temperature, but an assumption of regular solution behavior limits the applicability of the method. Chipman and Corrigan9,10 have developed an empirical correlation. based on the activity coefficient of nitrogen in the iron alloy at 1600°C, which facilitates the estimation of nitrogen solubilities at higher temperatures. This method also has limitations, due to the necessity of calculating the activity coefficient for nitrogen in a multicomponent iron alloy at 1600°C from the nitrogen solubility data for binary iron alloys. The shortcoming of such a straightforward approach to the problem of predicting nitrogen solubilities is the disregard of mutual interactions between elements in a complex iron melt. This investigation was conducted in an attempt to provide a more reliable method of predicting nitrogen solubilities in multicomponent iron alloys. The effects of the mutual interactions between chromium, nickel, silicon, molybdenum, or columbium in iron were studied, using the Sieverts' technique1,7 to measure the effects of alloy composition, temperature, and pressure on the solubility of nitrogen in ternary liquid iron alloys.

Jan 1, 1967

By Franklin J. Hill, Theodore D. Tiemann

Sized fractions of Wisconsin Gogebic taconite were reduced with hydrogen over the temperature range from 600° to 1000°C. In general, the degree and rate of reduction increase with temperature. Particle size has no observable effect except in the smaller fractions at 900°C and above, where reduction is impeded, possibly due to the siliceous nature of the ore. Gaseous diffusion appears to be significant as a rate controlling factor at certain stages. THE depletion of high grade iron ore reserves in the United States has established the need to utilize all available iron ore deposits, both in long range planning and from the viewpoint of national emergency. This has led to extensive research and development in this field. The beneficiation of Wisconsin Gogebic taconite ore has been previously studied by investigators at the University of Wiscconsin, 1 the United States Bureau of Mines,, Battelle Memorial Institute, 3 and others. Methods investigated have included concentration by flotation processes, magnetic and gravity separation, magnetic roasting and various combinations of them. The foregoing studies have been concerned with the production of an enriched ore suitable for blast furnace use. If the ore could first be reduced to metallic iron and then beneficiated, the product could be used directly in the open hearth or electric steel-making furnace. The by-passing of the blast furnace should enhance the economic feasibility of the beneficiating process. The work reported here,4 was undertaken to establish data on the hydrogen reduction of Wisconsin taconite that would eventually lead to the development of an economic direct reduction process for this and perhaps other low grade siliceous ores. The volume of work on direct reduction can be judged by the fact that 240 direct reduction processes were patented in the United States alone up to 1951, 5 and numerous additional processes have since been developed. Some of the factors contributing to direct reduction development are: 1) The increasing capital cost of the blast furnace and its accessory equipment. 2) The decreasing availability of high grade domestic ore. 3) The high cost of steel scrap for use in the open hearth and electric furnaces. In general, direct reduction processes can be divided into two types; those using a solid reductant (coal, peat, lignite) usually carried out in a kiln, and those using a gaseous reductant (H2, CO) in a shaft furnace or a fluidized bed retort. As there is no low cost coal readily available in northern Wisconsin but natural gas could be quite easily obtained, it is believed a gaseous reductant process would offer the greater feasibility for use on Wisconsin taconite. It is hoped that this preliminary work will beof interest to other investigators in this increasingly important field. TACONITE ORE The ore used in the investigation was obtained originally from the U. S. Bureau of Mines, and consisted of a representative composite made up from trench samples of the Norrie, Pabst, Plymouth, Pence, and Yale members of the Wisconsin Gogebic range iron formation. Chemically, the ore contains approximately 52 pct SiO, and 30 pct Fe. X-ray diffraction and other studies indicate the principal minerals to be quartz (SiO2), hematite (Fe2O3), and goethite (Fe2O3. H2O). Minor amounts of iron containing silicates, siderite (FecO3), and magnetite (FeO-Fe2O3) are present. The iron minerals and quartz are so finely disseminated that the ore requires grinding to less than 200 mesh (74 µ) for essential liberation.l,2 The iron content of each of the several size fractions studied is shown in Table I. EXPERIMENTAL METHOD The method used throughout the investigation was based on that developed by the U. S. Bureau of Mines in Minneaopolis6,7 in which the course of reduction is followed by the loss in weight of the ore sample. More specifically, a 100-g sample of the size frac-

Jan 1, 1962

By R. W. Parsons, P. R. Chaney

Oil recovery by the imbibition mechanism can be important in fractured carbonate reservoirs with a bottom water drive. Laboratory experiments were performed on water-wet carbonate rocks to model this process. The results are interpreted in light of the applicable scaling laws. The imbibition production behavior of a pillar of rock subjected to a slowly rising water table can be synthesized from data on total immersion experiments on small rock samples. If the rate of water table rise is slow enough and if the physical properties are such that the imbibition zone is of a small vertical extent, then only the final oil recovery on the small samples need be known. Applying laboratory imbibition data to a real reservoir should be done with caution because of possible wettability problems and the unknown behavior of two-phase flow in fractures. INTRODUCTION The spontaneous taking up of a preferential wetting fluid into a porous medium with the simultaneous expulsion of the contained fluid is termed imbibition. One of the many physical imbibition processes is the production of oil by the taking up of water into a water-wet reservoir rock. In certain types of heterogeneous reservoirs, e.g., fractured, it is realized that imbibition alone may be the dominant mechanism. Theoretical studies of imbibition oil recovery have followed several lines of attack. The behavior of certain mathematically tractable and conceptually simple models have been analyzed. Birks1 considered a bundle of vertical capillaries model, while Perotti et al.2 and Kelemen3 used a model of a series of vertically oriented fractures. If the oil production behavior from a block of reservoir rock is known, then the cumulative behavior of a vertical stack of these blocks subjected to a rising water table can be determined by a method outlined by Aronofsky et al. 4 Knowing the capillary pressure and relative permeability functions should uniquely set the imbibition behavior for a given sample. Solutions of the partial differential equations describing the process, however, present some formidable problems. Digital computer techniques have been applied to displacement processes in which the capillary pressure has been included.5"8 More recently, similar techniques have been used by Blair 9 to calculate countercurrent imbibition behavior. The fact that imbibition behavior is described by the usual fluid flow equations (Darcy's Law and continuity equation) implies that the derived scaling laws should apply equally to this situation. Use of model experiments to study imbibition has been employed by Graham and Richardson 10 and Mattax and Kyte,11 who actually tested the scaling law applicability. This study is concerned with scaled model imbibition experiments on water-wet carbonate rocks. Of particular interest is the slowly rising water table experiment. This simulates a highly fractured reservoir with the water table rising uniformly through the vertical fracture system. Experiments were performed on different sized samples and with different rates of rise of the water-oil interface surrounding the rock pillar. Total immersion imbibition experiments on smaller rock samples were performed to test the basic linear scaling laws and to see if these simpler tests could be used to synthesize the rising water table experimental results. THEORY IMBIBITION SCALING LAWS Scaling laws for the flow of two incompressible immiscible fluids in a porous medium have been presented by Rapoport.12 These are derived directly from Darcy's Law for the individual phases and the continuity equation. Results from a laboratory model experiment will duplicate those from some reservoir prototype if a constant proportion is maintained among the three forces acting on the fluids — the capillary pressure gradient, the gravitational gradient and the flowing pressure gradient. Operation of the model (i.e., fluid injection or withdrawal) must be conducted in accordance with specific equations. If the

Jan 1, 1967

By M. R. J. Wyllie, Walter D. Rose

The use of electrical well logs for the quantitative determination of such reservoir parameters as connate water saturation, formation permeability and connate water salinity has recently been attracting the attention of a number of workers1,2,3,4,5. While the theory of the determination of connate water salinity from the self potential S.P. log has received rather detailed treatment, relatively little attention has been paid to the theoretical aspects involved in the quantitative interpretation of resistivity data. It is clear that if electrical well logs can be used for the quantitative evaluation of physical characteristics of reservoir rock, they will provide a valuable tool to supplement cheaply information obtained by more laborious core analysis. In certain cases it is conceivable that the coring program could be considerably curtailed if the electric log could be relied upon to give reasonably accurate quantitative information. It is our object in this paper to examine the theoretical basis of quantitative log interpretation as expressed in such well-established logging concepts as formation factor and cementation factor. It is also our object to investigate the physical aspects of the rela- tionship which is presumed to exist between resistivity index and brine saturation in reservoir rock. In particular, we will endeavor to draw attention to the fact that it is possible to express these logging concepts in terms of capillary pressure-saturation relationships, permeability and tortuosity, parameters which we will consider in this paper to be fundamentally indicative of rock texture. The probability of being able to obtain from log recordings alone the data theoretically essential to permit quantitative log interpretatiou will be examined, and consideration will also be given to the problem of formulating simple semi-empirical relationships for use in the field. THEORETICAL CONSIDERATIONS The concept of formation resistivity factor, or as it is now commonly called, formation factor, appears to have been introduced by G. E. Archie",". Formation resistivity factor as defined by Archie is the resistivity of a rock 100 per cent brine-saturated divided by the resistivity of the brine. This relationship had previously been used by physical chemists and the concept is, for example, implicit in an early treatment by Fricke7 of the conductivity of aqueous slurries. Archie was able to establish the fact that although the relationship between formation factor and porosity did not change too greatly for different rock textures, the relationship between formation factor and permeability was markedly dependent on rock texture. The relationship found by Archie between formation factor and porosity was expanded by H. Guyod8. Archie had suggested that the formation factor, F, could be expressed in terms of the porosity, F, as follows: F =F-m .... (11 where, F = effective porosity fraction of the sand, and, m = an exponent greater than about 1.3. Guyod introduced the term cementation factor for the exponent, m, since it may be qualitatively shown that formation factor for any given porosity tends to increase as the sand becomes more cemented. It would appear that the concept of m as an exponent representing the cementation in a sand is strictly only of qualitative value, since the quantitative estimation of m by means other than the determination of F and F has not been possible. Guyod suggests that m can be estimated from a visual examination of a sample of rock, but this method appears to be both arbitrary and unreliable. It can be said, however, that in intergranular reservoirs of practical interest, the range of m is from about 1.4 to 3.0. A possible explanation for the fact that m is found to lie between these limits will be offered below. The determination of formation factor is an essential preliminary to the

Jan 1, 1950

By J. H. Scaff, H. C. Theurer, E. E. Schumacher

The microwave region of the radio spectrum was effectively utilized in radar designs during the recent war and it has become of increasing interest in the field of communications. Work in this field has led to an important use for silicon—that of the point contact rectifiers†1 in the frequency converter of microwave (radar or radio) receivers—and has stimulated considerable interest in the electrical properties and preparation of silicon and its alloys. Silicon is an electronic semiconductor. Its conductivity at room temperature results principally from the presence of certain impurities. While for metals an increase in impurity content increases the resistivity, for semiconductors such as silicon the opposite occurs and, in general, the addition of impurities lowers the resistivity. Silicon materials may be classified into one of two groups depending upon the manner in which the impurities contribute to electrical properties. These have been termed for convenience p-type or n-type. P-type silicon develops a very large positive thermal emf against metals, has a Hall coefficient of positive sign and a low resistance direction in point contact rectification with the silicon positive with respect to the point. N-type silicon, on the other hand, develops a negative thermal emf against metals, has a Hall coefficient of negative sign and a low resistance direction in rectification with the silicon negative with respect to the point. Impurities which produce n-type silicon are called donors inasmuch as these elements contribute to electrical conductivity by donating electrons to an unfilled energy band in the silicon. On the other hand, elements which produce p-type silicon are known as acceptors as these impurities contribute to the electrical conductivity by accepting electrons from a filled energy band permitting what is known as conductivity by "holes" in which the sign of the carriers appears to be positive. A general treatment of the mechanism of conduction in semiconductors from the viewpoint of modern band theory has been given recently by Pearson,2 by Becker, Green and Pearson,3 and by Torrey and Whitmer.4 In this investigation boron and aluminum have been found to be acceptors, and phosphorus, arsenic, and antimony to be donors in silicon. Data on the effect of boron and phosphorus on the electrical properties, when present singly and in combination, have been acquired. These data are discussed in the present paper. Raw Materials Used and Methods for Adding Seeond Constituents Silicon from two sources was used in this work and these will be referred to as A and B respectively. Silicon A is a material of high purity supplied by the Electro Metallurgical Co. It is prepared by chemical purification of "commercial" silicon obtained from the arc furnace reduction of SiO2. It contains 99.8 pct silicon, minimum, with small amounts of calcium, iron, aluminum, boron, and phosphorus as the principal impurities. This material was extensively employed in these studies as well as in the commercial preparation of rectifier materials. Silicon B is a material of high purity from the du-Pont Co. It is prepared by a pyrolytic reduction of Sicl4 and is free of analytically detectable amounts of boron and phosphorus. Its use permitted study of the effect of boron and phosphorus individually on the properties. This material contains, however, spec-troscopic traees of a number of metals, some of which affect electrical and rectification properties. Typical analyses for the two grades of silicon are given in Table 1. To make controlled additions of boron to the charge it was necessary to employ a low boron content master alloy since the quantity of boron to be added was usually only a few thousandths of one percent. The alloy containing nominally one percent boron was prepared by melting chemically pure boron with silicon A using the melting techniques for 320 g silicon

Jan 1, 1950

By S. R. B. Cooke, H. S. Choi, D. H. Harraway, I. Iwasaki

The mineralogy of natural iron ore samples and their slimes have been investigated and the nature of slime interference in iron ore flotation has been studied. The results have been correlated with the flotation behavior of a natural ore sample. Various conclusions have been reached as a result of these studies. In the flotation of iron oxide ores, desliming is generally considered to be an essential step to successful separation, irrespective of whether the iron oxide or siliceous gangue minerals are to be floated, although some workers have found empirically that certain collectors and reagent combinations are less sensitive to the presence of slime than others. The detrimental effect of slime is considered to be twofold. First, the presence of slime presupposes a high reagent consumption because of high specific surface. When clays are present and when cationic collectors are used abstraction by ionic exchange may augment this condition. Attempts to compensate by the addition of large amounts of reagent result in only partial correction. Second, slime coatings on granular particles tend to interfere with the bubble-mineral contact. The nature of slime coatings in flotation is quite complex and has been the subject of considerable study; an attempt was recently made by Fuerstenau et al.' to relate the slime-coating density with flotation recovery and with the properties of the electrical double layer at the mineral surfaces. Although major constituent minerals in the oxidized iron ores of the Mesabi and Cuyuna ranges are hematite and goethite (limonite) as the iron oxides, and quartz and chert as the siliceous gangue, very little is known of the mineralogy and of the chemical and physical characteristics of the slimes, and still less of the interaction between slimes, collector, and the mineral surfaces. For pragmatic reasons iron ore slimes are defined as — 20p material, based upon the calculated settling velocity of a quartz sphere of the stated diameter, and of all other equal-settling mineral particles. Active slime interference with flotation is usually attributed to particles 5p in size or finer, the extent of such interference appearing to depend not only on the mineralogy but also on the size distribution of each mineral in the slime fraction. The objective of this work was to acquire a more specific knowledge of the constitution of iron ore slimes and of their role in flotation. The mineralogi-cal composition of natural slimes was obtained by differential thernal analysis (hereinafter referred to as DTA), electron microscopy, and chemical and X-ray analyses. Some flotation tests were made on natural ore samples. The surface properties of several constituent minerals were investigated by electrophoretic measurements and by determination of the adsorption of some typical flotation collectors. Finally, simplified flotation tests were made on granular goethite and quartz in the presence of various artifically prepared slimes; the results were compared with laboratory flotation tests made on natural ores. MATERIAL AND METHODS Mineralogy of Some Iron Ore Slimes: Samples of two wash-ore tailing::, hereinafter identified as A* and B, *Sample A of the present investigation 18 the same am ore A in ref. 3. of a wash ore C, and of a paint rock D, all from the Mesabi range, were selected for investigation on the basis of prior information concerning their flotation behavior. The two wash-ore tailings, when deslimed, were known to respond well to flotation, whereas the wash ore was high in goethite, tended to be slimy, and responded poorly to flotation. The paint rock also exhibited sliming tendencies, and was suspected to contain relatively large quantities of clay minerals because of its high A1203 content. Gruner states that the paint rock of the Mesabi frequently contains kaolinite. To ascertain the relative sliming tendencies of each sample a standardized desliming method was employed. All samples were ground through 65 mesh using jaw and rolls crushers. A 500-g sample of each

Jan 1, 1962

By J. H. Scaff, W. G. Pfann

The effects of impurities on the electrical properties of silicon are discussed in a companion paper by Messrs. Scaff, Theuerer, and Schumacher.' It was shown that an ingot of silicon which contained boron and phosphorus in certain concentrations consisted partly of p-silicon and partly of n-silicon2 and that the common boundary between these regions was the source of a photo-voltage. These features were ascribed to the segregation of boron and phosphorus during solidification of the ingot. Because of different rates of segregation the first portion of the ingot to freeze contained a molar excess of boron over phosphorus and hence was p-silicon. The last-solidified region contained a molar excess of phosphorus and was n-silicon. This paper is concerned with the microscopic examination of such ingots. The microstructures are rather unusual in certain respects and their study has helped to show how the segregation of minor elements modifies the electrical properties of silicon. The microstructures of ingots prepared from two lots of silicon, designated 1 and 2, will be described. These lots were obtained from the Electro Metallurgical Co. Both contain 99.8+ pct silicon, but they differ in impurity analysis. For each lot will be shown the microstruc-ture of a slowly cooled ingot, for which the time of solidification is 6 min., and that of a rapidly cooled ingot, for which the time of solidification is 2 min. The ingots were prepared from 45 g charges of silicon. When an alloy freezes a cored structure is generally produced because of insufficient diffusion to remove concentration differences established during freezing. As a result of coring the first portion of a crystal to freeze is usually poorer in solute than equilibrium requires, while the last material to solidify is richer. In a columnar grain, growth is principally unidirectional and coring can produce a concentration gradient along the entire grain. By carrying the picture of the coring process from a single grain to an entire ingot in which columnar grains are aligned more or less radially, one can easily see that a composition gradient could be established between the outside and center of the ingot. This, to a considerable extent, occurs during the solidification of a slowly cooled ingot of silicon. Slowly Cooled Ingot In slowly cooled ingots of both lots of silicon, columnar grains which are approximately radial in direction and longest at the top of the ingot enclose a region in which the shapes and align- ment of the grains are considerably less regular. The central region is last to solidify and contains cavities and inclusions. The sketch of Fig 1 illustrates some of these features, as well as others which will be described below. If a polished section of an ingot is etched in a mixture of 2 parts of 20 pct HF and 98 parts of HNO3 the p-n barrier becomes visible. The overall shape of the barrier in a slowly-cooled ingot is roughly oval, as may be seen in Fig 1. The proportion of n-silicon, that is, the region enclosed by the barrier, is considerably greater in ingots of lot 1 than in those of lot 2. A sample about 34 x 1/8 X 1/8 in. was cut from a slowly cooled ingot of lot 1 with its long direction extending from the top of the ingot to the porous region. Thus its upper half was psilicon, its lower half n-silicon. A longitudinal face was polished and etched in the acid mixture. The areas of interest are identified in Fig 2. A band of parallel markings extends across the sample in the columnar region. These striae are roughly parallel to the upper surface of the ingot and cross grain boundaries with only slight deviations. They are quite distinct in the n-silicon,

Jan 1, 1950

By P. A. Beck, Hsun Hu

It has been known for many years that in cold drawn polycrystalline aluminum the recrystallization texture is practically identical with the deformation texture.l,2,3 V. Goeler and Sachs4 stated that in cold rolled polycrystalline aluminum, too, the deformation texture is retained upon recrystallization. This behavior was interpreted by Dehlinger9 as an indication that each recrystallized grain inherits the orientation of the matrix in which it grew. However, Burgers and Basart showed6 that in deformed aluminum single crystals the orientation of the recrystallized grains strongly deviates from that of the matrix. Barrett demonstrated8 that even in deformed polycrystalline aggregates the local orientation within each deformed grain changes on recrystallization. No explanation has as yet been offered of how the aggregate texture can be retained, while the local texture is everywhere changing. According to Burgers and Louwerse6 the orientation change on recrystallization in compressed and rolled aluminum single crystals corresponds to a rotation around [112] axes lying in the active slip planes and perpendicular to active slip directions. This orientation change was rationalized by them on the assumption that the orientation of the recrystallized grains is determined by the orientation of the available nuclei, and that these nuclei are small fragments of the deformed crystal, rotated in the deformation process. Barrett pointed out,? however, that these assumptions were by no means proven, and that the total volume of material necessary for the nuclei is so small, that it must be available in any orien- tation whatever. It is, therefore, unlikely that an "oriented nucleation" theory could satisfactorily explain the orientation changes in recrystallization of a deformed crystal. Furthermore, in contradiction to Burgers and LOU-werse's conclusions, Barrett's results for the orientation change could be best expressed in terms of rotations around. [Ill] axes. Thus agreement is lacking not only in the interpretations but apparently even in the experimental results contributed by the various investigators. The orientation relationships on coarsening* in a highly oriented polycrystalline matrix were first investigated by Burgers and Basart.5 They produced a fine grained highly oriented matrix by the recrystallization of a compressed or rolled single crystal of aluminum, and studied the orientation relationships in three successive generations of crystals: the "deformation texture" in the single crystal, the recrystallization texture, and the coarsening texture. Burgers24 showed that the preferred orientation of each successive generation was almost always widely different from that of the preceding one, but that the coarse grains often approximately reverted to the orientation of their grandparent, the deformed single crystal. This observation, and the idea that the orientation of the coarse grains is determined by that of the available "nuclei," led to the concept that the coarse grains are nucleated by the remnants of the deformation texture.12,15 On the other hand, Bowles and Boas16 found, in a carefully conducted experiment, that in recrystallized fine grained copper of cube texture coarse grains grow in orientations which can be derived from the orientation of the recrystallized matrix by rotation around a [lll].] direction: the coarsening texture here does not appear to be related in any simple manner to the original rolling texture from which the cube texture had been obtained by recrystallization. It may be assumed that in a recrystallized material, even with a strong texture, there always are present some grains of practically any orientation. These may serve as "nuclei" for the coarse grains, provided that the conditions are favorable for their growth. The existence of a coarsening texture may be considered as an indication that grains with certain relative orientations with respect to the preferred orientation of their neighbors can grow much faster than others. This "oriented growth" theory was briefly suggested by van Arkel, as early as 1936,13 and it was mentioned by Burgers." Recently, C. G. Dunn produced direct

Jan 1, 1950

By David L. Sikarskie

The measurement of residual stress fields using X-ray diffraction techniques requires the removal of successive layers of material from the specimen. In the process of removing these layers, the underlying residual stress field is altered; hence, if the original stress field is desired, corrections must be made to the measured stresses. Although these corrections already exist for a number of cases, an alternate procedure is outlined herein whereby the corrections are presented in series form. This form is numerically more convenient within certain ranges of correction depths and in its simplicity gives additional insight into the factors affecting the corrections. It, further, readily permits determining the proper slice depth to remove and the effect on the correction of both specimen thickness and magnitude and form of the measured residual stress itself. ONE of the techniques currently being used to determine residual stress fields is X-ray diffraction. Since X-rays are diffracted essentially from the layers of atoms near the surface of the specimen, of the order of 0.0001 to 0.001 in. depending on conditions, the method can only determine stresses* in this very thin surface region. Therefore, if the residual stress field at some depth into the specimen is required it is necessary to remove successive layers of material taking measurements after each cut. In the process of removing a thin surface layer of stressed material, however, the over-all equilibrium of a cross section of the specimen is disturbed with the result that the internal residual stress which existed before the slice of material was removed is altered. This alteration of stress occurs after each slice and its effect is cumulative. Thus, if the original stress distribution is desired, corrections must be applied to the measured stresses. These corrections can be found by satisfying equilibrium on each new cross section. These corrections have been derived in detail for a number of cases, e.g., cylinders, bars, plates,' and also are given in Appendix VI of Ref. 2. In each of the above cases the correction terms require the evaluation of definite integrals of the measured residual stress distribution. In general, this is indeed the way one would proceed with the corrections. There are a number of instances, however, where the integrals can be replaced by a series form of correction which is considerably more convenient numerically and, also, gives added insight into the factors which influence the corrections. Such a form of the correction is particularly useful, for example, if one is interested in designing a test such that stress corrections will be small. Also, the question of what depth of slice to use in relation to both specimen thickness and residual stress distribution itself must invariably be answered. Questions of this type can be readily answered using a series form of correction. In addition, if the correct residual stress distribution is needed only for limited depths into the specimen the series correction provides numerical results which are equivalent to the integral correction. I) DERIVATION OF THE SERIES CORRECTION The problem to be considered here is that of a bar or plate,* i.e., either one or two dimensions of the specimen is large compared with the third. Also, the residual stress distributions considered depend only on z, see Fig. 1. In view of this it can be shown' that a stress correction, based on simple beam theory, satisfies all conditions of "elasticity theory" and hence is the correct (and only) solution. The integral form of the correction (this assumes that the measured residual stress is a piecewise continuous function) as given in Ref. 1 is:

Jan 1, 1968